Enhanced biomimetic performance of ionic polymer-metal composite actuators prepared with nanostructured block ionomers.

Ionic polymer-metal composites (IPMCs) represent an important class of stimuli-responsive polymers that are capable of bending upon application of an electric potential. Conventional IPMCs, prepared with Nafion and related polyelectrolytes, often suffer from processing challenges, relatively low actuation levels and back relaxation during actuation. In this study, we examine and compare the effects of fabrication and solvent on the actuation behavior of a block ionomer with a sulfonated midblock and glassy endblocks that are capable of self-organizing and thus stabilizing a molecular network in the presence of a polar solvent. Unlike Nafion, this material can be readily dissolved and cast from solution to yield films that vary in thickness and exhibit enormous solvent uptake. Cycling the initial chemical deposition of Pt on the surfaces of swollen films (the compositing process) increases the extent to which the electrodes penetrate the films, thereby improving contact along the polymer/electrode interface. The maximum bending actuation measured from IPMCs prepared with different solvents is at least comparable, but is often superior, to that reported for conventional IPMCs, without evidence of back relaxation. An unexpected characteristic observed here is that the actuation direction can be solvent regulated. Our results confirm that this block ionomer constitutes an attractive alternative for use in IPMCs and their associated applications.

Long-range alignment of gold nanorods in electrospun polymer nano/microfibers.

In this study, a scalable fabrication technique for controlling and maintaining the nanoscale orientation of gold nanorods (GNRs) with long-range macroscale order has been achieved through electrospinning. The volume fraction of GNRs with an average aspect ratio of 3.1 is varied from 0.006 to 0.045 in aqueous poly(ethylene oxide) solutions to generate electrospun fibers possessing different GNR concentrations and measuring 40-3000 nm in diameter. The GNRs within these fibers exhibit excellent alignment with their longitudinal axis parallel to the fiber axis n. According to microscopy analysis, the average deviant angle between the GNR axis and n increases modestly from 3.8 to 13.3° as the fiber diameter increases. Complementary electron diffraction measurements confirm preferred orientation of the {100} GNR planes. Optical absorbance spectroscopy measurements reveal that the longitudinal surface plasmon resonance bands of the aligned GNRs depend on the polarization angle and that maximum extinction occurs when the polarization is parallel to n.

Characterization and optimization of RGD-containing silk blends to support osteoblastic differentiation.

The effect of blending two silk proteins, regenerated Bombyx mori fibroin and synthetic spidroin containing RGD, on silk film material structure (beta-sheet content) and properties (solubility), as well as on biological response (osteoblast adhesion, proliferation and differentiation) was investigated. Although the elasticity and strength of silks make them attractive candidates for bone, ligament, and cartilage tissue engineering applications, silk proteins generally lack bioactive peptides for enhancing cell functions. Thus, a synthetic spider silk, spidroin, containing two RGD cell adhesive sequences (RGD-spidroin) was engineered. RGD-spidroin was blended with different ratios of fibroin and spun coat into films on glass coverslips. beta-Sheet formation, contact angle, surface topography and RGD surface presentation were characterized and correlated with cell behavior. We found that the amount of beta-sheet formation was directly related to the RGD-spidroin content of the blends after annealing, with the pure RGD-spidroin demonstrating the highest amount of beta-sheet content. The increased beta-sheet content improved film stability under culture conditions. A new visualization technique demonstrated that the RGD presentation on the film surface was affected by both the RGD-spidroin content and annealing conditions. It was determined that 10mass% RGD-spidroin was necessary to improve film stability and to achieve osteoblast attachment and differentiation.

Preparation of combinatorial arrays of polymer thin films for transmission electron microscopy analysis.

We present a new method for harvesting multiple thin film specimens from polymer combinatorial libraries for transmission electron microscopy (TEM) analysis. Such methods are of interest to researchers who wish to integrate TEM measurements into a combinatorial or high-throughput experimental workflow. Our technique employs poly(acrylic acid) plugs, sequestered in an elastomer gasket, to extract a series of film patches from gradient combinatorial libraries. A strategy for simultaneous deposition of the array of film specimens onto TEM grids also is described. We demonstrate our technique using nanostructured polymer thin film libraries as test cases in which the nanoscale details can be successfully imaged. Microscopy of test case specimens demonstrates that these samples are of sufficient quality for morphology screening via TEM, and in some cases are sufficient for more detailed morphological studies.

Responsive PET nano/microfibers via surface-initiated polymerization.

Poly(ethylene terephthalate) (PET) is one of the most important thermoplastics in ubiquitous use today because of its mechanical properties, clarity, solvent resistance, and recyclability. In this work, we functionalize the surface of electrospun PET microfibers by growing poly(N-isopropylacrylamide) (PNIPAAm) brushes through a chemical sequence that avoids PET degradation to generate thermoresponsive microfibers that remain mechanically robust. Amidation of deposited 3-aminopropyltriethoxysilane, followed by hydrolysis, yields silanol groups that permit surface attachment of initiator molecules, which can be used to grow PNIPAAm via "grafting from" atom-transfer radical polymerization. Spectroscopic analyses performed after each step confirm the expected reaction and the ultimate growth of PNIPAAm brushes. Water contact-angle measurements conducted at temperatures below and above the lower critical solution temperature of PNIPAAm, coupled with adsorption of Au nanoparticles from aqueous suspension, demonstrate that the brushes retain their reversible thermoresponsive nature, thereby making PNIPAAm-functionalized PET microfibers suitable for filtration media, tissue scaffolds, delivery vehicles, and sensors requiring robust microfibers.

High-content profiling of cell responsiveness to graded substrates based on combinyatorially variant polymers.

We have developed a novel approach combining high information and high throughput analysis to characterize cell adhesive responses to biomaterial substrates possessing gradients in surface topography. These gradients were fabricated by subjecting thin film blends of tyrosine-derived polycarbonates, i.e. poly(DTE carbonate) and poly(DTO carbonate) to a gradient temperature annealing protocol. Saos-2 cells engineered with a green fluorescent protein (GFP) reporter for farnesylation (GFP-f) were cultured on the gradient substrates to assess the effects of nanoscale surface topology and roughness that arise during the phase separation process on cell attachment and adhesion strength. The high throughput imaging approach allowed us to rapidly identify the "global" and "high content" structure-property relationships between cell adhesion and biomaterial properties such as polymer chemistry and topography. This study found that cell attachment and spreading increased monotonically with DTE content and were significantly elevated at the position with intermediate regions corresponding to the highest "gradient" of surface roughness, while GFP-f farnesylation intensity descriptors were sensitively altered by surface roughness, even in cells with comparable levels of spreading.