Fabrication and application of composite adsorbents made by one-pot electrochemical exfoliation of graphite in surfactant ionic liquid/nanocellulose mixtures.

Previously, surfactant-assisted exfoliated graphene oxide (sEGO) formed with the triple-chain surfactant TC14 (sodium 1,4-bis(neopentyloxy)-3-(neopentylcarbonyl)-1,4-dioxobutane-2-sulfonate) was applied in wastewater treatment. The extent of dye-removal and the adsorption capacity of the sEGO formed with this triple-chain surfactant outperformed those of two other systems, namely, the di-chain version of TC14 (AOT14; sodium 1,2-bis-(2,2-dimethyl-propoxycarbonyl)-ethanesulfonate) and the single-chain surfactant sodium n-dodecylsulfate. In the present study, to further optimise the surfactant chemical structure, the sodium ion of TC14 was substituted with 1-butyl-3-methyl-imidazolium (BMIM) generating surfactant ionic liquids (SAILs; 1-butyl-3-imidazolium 1,4-bis(neopentyloxy)-3-(neopentyloxycarbonyl)-1,4-dioxobutane-2-sulfonate), hereafter denoted as BMIM-TC14. This SAIL, together with nanofibrillated kenaf cellulose (NFC), was used to electrochemically exfoliate graphite, yielding BMIM-TC14 sEGO/NFC composites. These highly hydrophobic polymer composites were then used for the removal of methylene blue (MB) from aqueous solution. 1H NMR spectroscopy was used to elucidate the structure of the synthesised SAILs. The morphologies of the resulting nanocomposites were investigated using Raman spectroscopy, field-emission scanning electron microscopy, and high-resolution transmission electron microscopy. Analysis using small-angle neutron scattering was performed to examine the aggregation behaviour of sEGO and custom-made SAILs. Zeta potential, surface tension, and dynamic light-scattering measurements were used to study the aqueous properties and colloidal stability of the suspension. Amongst the surfactants tested, BMIM-TC14 sEGO/NFC exhibited the highest MB adsorption ability, achieving 99% dye removal under optimum conditions. These results highlight the importance of modifying the hydrophilic moieties of amphiphilic compounds to improve the performance of sEGO/NFC composites as effective adsorbents for wastewater treatment.

Design of Surfactant Tails for Effective Surface Tension Reduction and Micellization in Water and/or Supercritical CO2.

The interfacial properties and water-in-CO2 (W/CO2) microemulsion (µE) formation with double- and novel triple-tail surfactants bearing trimethylsilyl (TMS) groups in the tails are investigated. Comparisons of these properties are made with those for analogous hydrocarbon (HC) and fluorocarbon (FC) tail surfactants. Surface tension measurements allowed for critical micelle concentrations (CMC) and surface tensions at the CMC (γCMC) to be determined, resulting in the following trend in surface activity FC > TMS > HC. Addition of a third surfactant tail gave rise to increased surface activity, and very low γCMC values were recorded for the double/triple-tail TMS and HC surfactants. Comparing effective tail group densities (ρlayer) of the respective surfactants allowed for an understanding of how γCMC is affected by both the number of surfactant tails and the chemistry of the tails. These results highlight the important role of tail group chemical structure on ρlayer for double-tail surfactants. For triple-tail surfactants, however, the degree to which ρlayer is affected by tail group architecture is harder to discern due to formation of highly dense layers. Stable W/CO2 µEs were formed by both the double- and the triple-tail TMS surfactants. High-pressure small-angle neutron scattering (HP-SANS) has been used to characterize the nanostructures of W/CO2 µEs formed by the double- and triple-tail surfactants, and at constant pressure and temperature, the aqueous cores of the microemulsions were found to swell with increasing water-to-surfactant ratio (W0). A maximum W0 value of 25 was recorded for the triple-tail TMS surfactant, which is very rare for nonfluorinated surfactants. These data therefore highlight important parameters required to design fluorine-free environmentally responsible surfactants for stabilizing W/CO2 µEs.

Water-in-CO2 Microemulsions Stabilized by an Efficient Catanionic Surfactant.

To facilitate potential applications of water-in-supercritical CO2 microemulsions (W/CO2 µEs) efficient and environmentally responsible surfactants are required with low levels of fluorination. As well as being able to stabilize water-CO2 interfaces, these surfactants must also be economical, prevent bioaccumulation and strong adhesion, deactivation of enzymes, and be tolerant to high salt environments. Recently, an ion paired catanionic surfactant with environmentally acceptable fluorinated C6 tails was found to be very effective at stabilizing W/CO2 µEs with high water-to-surfactant molar ratios (W0) up to ∼50 (Sagisaka, M.; et al. Langmuir 2019, 35, 3445-3454). As the cationic and anionic constituent surfactants alone did not stabilize W/CO2 µEs, this was the first demonstration of surfactant synergistic effects in W/CO2 microemulsions. The aim of this new study is to understand the origin of these intriguing effects by detailed investigations of nanostructure in W/CO2 microemulsions using high-pressure small-angle neutron scattering (HP-SANS). These HP-SANS experiments have been used to determine the headgroup interfacial area and volume, aggregation number, and effective packing parameter (EPP). These SANS data suggest the effectiveness of this surfactant originates from increased EPP and decreased hydrophilic/CO2-philic balance, related to a reduced effective headgroup ionicity. This surfactant bears separate C6F13 tails and oppositely charged headgroups, and was found to have a EPP value similar to that of a double C4F9-tail anionic surfactant (4FG(EO)2), which was previously reported to be one of most efficient stabilizers for W/CO2 µEs (maximum W0 = 60-80). Catanionic surfactants based on this new design will be key for generating superefficient W/CO2 µEs with high stability and water solubilization.

Highly branched triple-chain surfactant-mediated electrochemical exfoliation of graphite to obtain graphene oxide: colloidal behaviour and application in water treatment.

The generation of surfactant-assisted exfoliated graphene oxide (sEGO) by electrochemical exfoliation is influenced by the presence of surfactants, and in particular the hydrophobic tail molecular-architecture. Increasing surfactant chain branching may improve the affinity for the graphite surfaces to provide enhanced intersheet separation and stabilisation of exfoliated sheets. The resulting sEGO composites can be readily used to remove of a model pollutant, the dye, methylene blue (MB), from aqueous solutions by providing abundant sites for dye adsorption. This article explores relationships between surfactant structure and the performance of sEGO for MB adsorption. Double-branched and highly branched triple-chain graphene-compatible surfactants were successfully synthesised and characterised by 1H NMR spectroscopy. These surfactants were used to produce sEGO via electrochemical exfoliation of graphite, and the sEGOs generated were further utilised in batch adsorption studies of MB from aqueous solutions. The properties of these synthesised surfactants were compared with those of a common single-chain standard surfactant, sodium dodecyl-sulfate (SDS). The structural morphology of sEGO was assessed using Raman spectroscopy and field emission scanning electron microscopy (FESEM). To reveal the links between the hydrophobic chain structure and the sEGO adsorption capacity, UV-visible spectroscopy, zeta potential, and air-water (a/w) surface tension measurements were conducted. The aggregation behaviour of the surfactants was studied using small-angle neutron scattering (SANS). The highly branched triple-chain surfactant sodium 1,4-bis(neopentyloxy)-3-(neopentylcarbonyl)-1,4-dioxobutane-2-sulfonate (TC14) displayed enhanced exfoliating efficiency compared to those of the single-and double-chain surfactants, leading to ∼83% MB removal. The findings suggest that highly branched triple-chain surfactants are able to offer more adsorption sites, by expanding the sEGO interlayer gap for MB adsorption, compared to standard single-chain surfactants.

Water-in-CO2 Microemulsions Stabilized by Fluorinated Cation-Anion Surfactant Pairs.

High-water-content water-in-supercritical CO2 (W/CO2) microemulsions are considered to be green, universal solvents, having both polar and nonpolar domains. Unfortunately, these systems generally require environmentally unacceptable stabilizers like long and/or multifluorocarbon-tail surfactants. Here, a series of catanionic surfactants having more environmentally friendly fluorinated C4-C6 tails have been studied in terms of interfacial properties, aggregation behavior, and solubilizing power in water and/or CO2. Surface tensions and critical micelle concentrations of these catanionic surfactants are, respectively, lowered by ∼9 mN/m and 100 times than those of the constituent single fluorocarbon-tail surfactants. Disklike micelles in water were observed above the respective critical micelle concentrations, implying the catanionic surfactants have a high critical packing parameter, which should be suitable for the formation of reverse micelles. Based on visual observation of phase behavior and Fourier transform infrared spectroscopic and small-angle neutron scattering studies, one of the three catanionic surfactants tested was found to form transparent single-phase W/CO2 microemulsions with a water-to-surfactant molar ratio of up to ∼50. This is the first successful demonstration of the formation of W/CO2 microemulsions by synergistic ion-pairing of anionic and cationic single-tail surfactants. This indicates that catanionic surfactants offer a promising approach to generate high-water-content W/CO2 microemulsions.

Linear symmetric liquid crystal trimers exhibiting supramolecular chiral architectures.

We prepared a homologous series of achiral liquid crystal trimers (I-n) in which two phenylpyrimidine units and one biphenyl unit were connected via flexible spacers, and investigated the physical properties. All the trimers possessing odd-numbered methylene spacers exhibited soft crystalline chiral conglomerate phases. X-ray diffraction measurements reveal that they have an intercalated layer structure. On the other hand, the trimers possessing even-numbered spacers showed nematic and smectic C phases. We investigated the surface structures of odd-membered trimers in the soft crystalline phases using scanning electron microscopy. Trimers I-3 and I-5 were found to form cylindrical tubes, whereas trimers I-7, I-9 and I-11 toroidal pits. We discuss the formation of diverse supramolecular architectures in terms of the anisotropy of the chirality transfer.

Trimethylsilyl hedgehogs - a novel class of super-efficient hydrocarbon surfactants.

Presented here are the results for a novel class of hydrocarbon surfactants, termed trimethylsilyl hedgehogs (TMS-hedgehogs), due to the presence of silicon in the tails. By comparing the surface properties of these hybrid hedgehogs to purely hydrocarbon equivalents, links between performance and the structure are made. Namely, by controlling the molecular volume of the surfactant fragments, improvements can be made in surface coverage, generating lower surface energy monolayers. Small-angle neutron scattering (SANS) data have been collected showing that these novel surfactants aggregate to form ellipsoidal micelles which grow with increasing concentration. This study highlights the sensitive relationship between surface tension and the surfactant chain, for designing new super-efficient surfactants close to the limit of the lowest surface tensions possible.

Shape Modification of Water-in-CO2 Microemulsion Droplets through Mixing of Hydrocarbon and Fluorocarbon Amphiphiles.

An oxygen-rich hydrocarbon (HC) amphiphile has been developed as an additive for supercritical CO2 (scCO2). The effects of this custom-designed amphiphile have been studied in water-in-CO2 (w/c) microemulsions stabilized by analogous fluorocarbon (FC) surfactants, nFG(EO)2, which are known to form spherical w/c microemulsion droplets. By applying contrast-variation small-angle neutron scattering (CV-SANS), evidence has been obtained for anisotropic structures in the mixed systems. The shape transition is attributed to the hydrocarbon additive, which modifies the curvature of the mixed surfactant films. This can be considered as a potential method to enhance physicochemical properties of scCO2 through elongation of w/c microemulsion droplets. More importantly, by studying self-assembly in these mixed systems, fundamental understanding can be developed on the packing of HC and FC amphiphiles at water/CO2 interfaces. This provides guidelines for the design of fluorine-free CO2 active surfactants, and therefore, practical industrial scale applications of scCO2 could be achieved.

New Class of Amphiphiles Designed for Use in Water-in-Supercritical CO2 Microemulsions.

Water-in-supercritical CO2 microemulsions formed using the hybrid F-H surfactant sodium 1-oxo-1-[4-(perfluorohexyl)phenyl]hexane-2-sulfonate, FC6-HC4, have recently been shown to have the highest water-solubilizing power ever reported. FC6-HC4 demonstrated the ability to outperform not only other surfactants but also other FCm-HCn analogues containing different fluorocarbon and hydrocarbon chain lengths (Sagisaka, M. et al. Langmuir 2015, 31, 7479-7487). With the aim of clarifying the key structural features of this surfactant, this study examined the phase behavior and water/supercritical CO2 aggregate formation of 1-oxo-1-[4-(perfluorohexyl)phenyl]hexane (Nohead FC6-HC4), which is an FC6-HC4 analogue but now, interestingly, without the sulfonate headgroup. Surprisingly, Nohead FC6-HC4, which would not normally be identified as a classic surfactant, yielded transparent single-phase W/CO2 microemulsions with polar cores able to solubilize a water-soluble dye, even at pressures and temperatures so low as to approach the critical point of CO2 (e.g., ∼100 bar at 35 °C). High-pressure small-angle scattering (SANS) measurements revealed the transparent phases to consist of ellipsoidal nanodroplets of water. The morphology of these droplets was shown to be dependent on the pressure, Nohead FC6-HC4 concentration, and water-to-surfactant molar ratio. Despite having almost the same structure as Nohead FC6-HC4, analogues containing both shorter and longer hydrocarbons were unable to form W/CO2 microemulsion droplets. This shows the importance of the role of the hydrocarbon chain in the stabilization of W/CO2 microemulsions. A detailed examination of the mechanism of Nohead FC6-HC4 adsorption onto the water surface suggests that the hexanoyl group protrudes into the aqueous core, allowing for association between the carbonyl group and water.

Effect of Fluorocarbon and Hydrocarbon Chain Lengths in Hybrid Surfactants for Supercritical CO2.

Hybrid surfactants containing both fluorocarbon (FC) and hydrocarbon (HC) chains have recently been shown to solubilize water and form elongated reversed micelles in supercritical CO2. To clarify the most effective FC and HC chain lengths, the aggregation behavior and interfacial properties of hybrid surfactants FCm-HCn (FC length m/HC length n = 4/2, 4/4, 6/2, 6/4, 6/5, 6/6, and 6/8) were examined in W/CO2 mixtures as functions of pressure, temperature, and water-to-surfactant molar ratio (W0). The solubilizing power of hybrid surfactants for W/CO2 microemulsions was strongly affected by not only the FC length but also by that of the HC. Although the surfactants having short FC and/or HC tails (namely, m/n = 4/2, 4/4, and 6/2) did not dissolve in supercritical CO2 (even at ∼17 mM, ≤400 bar, temperature ≤ 75 °C, and W0 = 0-40), the other hybrid surfactants were able to yield transparent single-phase W/CO2 mixtures identified as microemulsions. The solubilizing power of FC6-HCm surfactants reached a maximum (W0 ∼ 80 at 45 °C and 350 bar) with a hydrocarbon length, m, of 4. The W0 value of 80 is the highest for a HC-FC hybrid surfactant, matching the highest value reported for a FC surfactant which contained more FC groups. High-pressure small-angle neutron scattering measurements from FCm-HCn/D2O/CO2 microemulsions were consistent with growth of the microemulsion droplets with increasing W0. In addition, not only spherical reversed micelles but also nonspherical assemblies (rodlike or ellipsoidal) were found for the systems with FC6-HCn (n = 4-6). At fixed surfactant concentration and W0 (17 mM and W0 = 20), the longest reversed micelles were obtained for FC6-HC6 where a mean aspect ratio of 6.3 was calculated for the aqueous cores.

Periodic Formation/Breakdown of Lamellar Aggregates with Anionic Cyanobiphenyl Surfactants.

This study reports unusual behavior of aqueous-phase lamellar aggregates with a new class of hybrid surfactant, CB-B2ES, having mesogenic units {6-[4-(4-cyanophenyl)phenyloxy]hexyl} and temperature-sensitive oxyethylated (butoxyethoxyethyl) tails. These tails are poorly miscible and likely to microsegregate if the surfactant molecules assemble. Lamellar aggregates appear at CB-B2ES concentrations higher than 5 wt % and were found to undergo repeat formation/breakdown periodically at 30 °C, with an average domain lifetime of ∼10 s. To investigate effects of the temperature-sensitive oxyethylene units on the hydrophilic/lipophilic balance (HLB) of the CB-B2ES bilayers, a fluorescence probe 1-pyrene-carboxaldehide was solubilized in the mixtures to sense the micro-environmental polarities. Fluorimetric measurements suggested that the polarity of CB-B2ES bilayers is very similar to that of the non-ethoxylated CB-B2ES analogue at high temperatures (≥65 °C). However, for CB-B2ES, polarity increased with a decreasing temperature, in contrast with the small decrease in polarity observed for analogous non-ethoxylated bilayers. This is consistent with increased hydration of the oxyethylene units in CB-B2ES bilayers at low temperatures. The periodic formation/breakdown and cooling-induced hydrophilicity of the CB-B2ES lamellar aggregates did not appear in the non-hybrid and/or non-ethoxylated surfactant systems. Therefore, the combination of two unsymmetrical tails, one containing oxyethylene units and the other containing cyanobiphenyl terminal tips, must play an important role promoting this unusual behavior.

Low-surface energy surfactants with branched hydrocarbon architectures.

Surface tensiometry and small-angle neutron scattering have been used to characterize a new class of low-surface energy surfactants (LSESs), "hedgehog" surfactants. These surfactants are based on highly branched hydrocarbon (HC) chains as replacements for environmentally hazardous fluorocarbon surfactants and polymers. Tensiometric analyses indicate that a subtle structural modification in the tails and headgroup results in significant effects on limiting surface tensions γcmc at the critical micelle concentration: a higher level of branching and an increased counterion size promote an effective reduction of surface tension to low values for HC surfactants (γcmc ∼ 24 mN m(-1)). These LSESs present a new class of potentially very important materials, which form lamellar aggregates in aqueous solutions independent of dilution.

Hyperbranched hydrocarbon surfactants give fluorocarbon-like low surface energies.

Two series of Aerosol-OT-analogue surfactants (sulfosuccinate-type di-BCnSS and sulfoglutarate-type di-BCnSG) with hyperbranched alkyl double tails (so-called "hedgehog" groups, carbon number n = 6, 9, 12, and 18) have been synthesized and shown to demonstrate interfacial properties comparable to those seen for related fluorocarbon (FC) systems. Critical micelle concentration (CMC), surface tension at the CMC (γCMC), and minimum area per molecule (Amin) were obtained from surface tension measurements of aqueous surfactant solutions. The results were examined for relationships between the structure of the hedgehog group and packing density at the interface. To evaluate A and B values in the Klevens equation for these hedgehog surfactants, log(CMC) was plotted as a function of the total carbon number in the surfactant double tail. A linear relationship was observed, producing B values of 0.20-0.25 for di-BCnSS and di-BCnSG, compared to a value of 0.31 for standard double-straight-tail sulfosuccinate surfactants. The lower B values of these hedgehog surfactants highlight their lower hydrophobicity compared to double-straight-tail surfactants. To clarify how hydrocarbon density in the surfactant-tail layer (ρ(layer)) affects γCMC, the ρ(layer) of each double-tail surfactant was calculated and the relationship between γCMC and ρ(layer) examined. As expected for the design of low surface energy surfactant layers, ρ(layer) was identified as an important property for controlling γCMC with higher ρ(layer), leading to a lower γCMC. Interestingly, surfactants with BC9 and BC12 tails achieved much lower γCMC, even at low ρ(layer) values of <0.55 g cm(-3). The lowest surface energy surfactant studied here was di-BC6SS, which had a γCMC of only 23.8 mN m(-1). Such a low γCMC is comparable to those obtained with short FC-tail surfactants (e.g., 22.0 mN m(-1) for the sulfosuccinate-type FC-surfactant with R = F(CF2)6CH2CH2-).

Spreading of aqueous surfactant solutions on oil substrates: Superspreaders vs non-superspreaders.

HYPOTHESIS: The question of why aqueous solutions of some surfactants demonstrate a rapid spreading (superspreading) over hydrophobic solid substrates, while solutions of other similar surfactants do not, has no definitive explanation despite numerous previous studies. The suggested hypothesis for this study assumes that once the spreading coefficient of surfactant is positive, there is a concentration range for solutions of any surfactant which demonstrates rapid spreading. As it is impossible to calculate spreading coefficients for solid substrates, we compare the spreading performance of known superspreaders and non-superspreaders on liquid (oil) substrate. EXPERIMENTS: The kinetics of spreading of aqueous solutions of a series of branched ionic surfactants and non-ionic trisiloxane surfactants on two liquid substrates was studied and compared with the spreading of a surfactant-free liquid, silicone oil. Both dynamic and equilibrium spreading coefficients were calculated using measured surface and interfacial tensions. FINDINGS: There is no difference in spreading rate on liquid substrate between solutions of surfactants proven as superspreaders (while spreading on solid substrate) or non-superspreaders. A rapid spreading (superspreading) with the characteristic rate of spreading O(102-103) mm2/s occurs if the dynamic spreading coefficients exceeds the positive threshold value. If the dynamic spreading coefficient is negative or slightly positive, complete wetting still occurs, but the spreading is slow with the spreading rate is O(1) mm2/s. Spreading exponents for surfactant solutions in the rapid spreading regime are considerably larger than for the surfactant-free liquid. A number of spreading and dewetting patterns were observed depending on the surfactant type, its concentration and substrate.

Nanostructures in water-in-CO2 microemulsions stabilized by double-chain fluorocarbon solubilizers.

High-pressure small-angle neutron scattering (HP-SANS) studies were conducted to investigate nanostructures and interfacial properties of water-in-supercritical CO2 (W/CO2) microemulsions with double-fluorocarbon-tail anionic surfactants, having different fluorocarbon chain lengths and linking groups (glutarate or succinate). At constant pressure and temperature, the microemulsion aqueous cores were found to swell with an increase in water-to-surfactant ratio, W0, until their solubilizing capacities were reached. Surfactants with fluorocarbon chain lengths of n = 4, 6, and 8 formed spherical reversed micelles in supercritical CO2 even at W0 over the solubilizing powers as determined by phase behavior studies, suggesting formation of Winsor-IV W/CO2 microemulsions and then Winsor-II W/CO2 microemulsions. On the other hand, a short C2 chain fluorocarbon surfactant analogue displayed a transition from Winsor-IV microemulsions to lamellar liquid crystals at W0 = 25. Critical packing parameters and aggregation numbers were calculated by using area per headgroup, shell thickness, the core/shell radii determined from SANS data analysis: these parameters were used to help understand differences in aggregation behavior and solubilizing power in CO2. Increasing the microemulsion water loading led the critical packing parameter to decrease to ~1.3 and the aggregation number to increase to >90. Although these parameters were comparable between glutarate and succinate surfactants with the same fluorocarbon chain, decreasing the fluorocarbon chain length n reduced the critical packing parameter. At the same time, reducing chain length to 2 reduced negative interfacial curvature, favoring planar structures, as demonstrated by generation of lamellar liquid crystal phases.

Hybrid CO2-philic surfactants with low fluorine content.

The relationships between molecular architecture, aggregation, and interfacial activity of a new class of CO(2)-philic hybrid surfactants are investigated. The new hybrid surfactant CF2/AOT4 [sodium (4H,4H,5H,5H,5H-pentafluoropentyl-3,5,5-trimethyl-1-hexyl)-2-sulfosuccinate] was synthesized, having one hydrocarbon chain and one separate fluorocarbon chain. This hybrid H-F chain structure strikes a fine balance of properties, on one hand minimizing the fluorine content, while on the other maintaining a sufficient level of CO(2)-philicity. The surfactant has been investigated by a range of techniques including high-pressure phase behavior, UV-visible spectroscopy, small-angle neutron scattering (SANS), and air-water (a/w) surface tension measurements. The results advance the understanding of structure-function relationships for generating CO(2)-philic surfactants and are therefore beneficial for expanding applications of CO(2) to realize its potential using the most economic and efficient surfactants.

Effective and efficient surfactant for CO2 having only short fluorocarbon chains.

A previous study (Langmuir2011, 27, 5772) found the fluorinated double-tail sulfogulutarate 8FG(EO)(2) to act as a superefficient solubilizer for water in supercritical CO(2) (W/CO(2)) microemulsions. To explore more economic CO(2)-philic surfactants with high solubilizing power as well as rapid solubilization rates, the effects of fluorocarbon chain length and linking group were examined with sodium 1,5-bis(1H,1H,2H,2H-perfluoroalkyloxy)-1,5-dioxopentane-2-sulfonates (nFG(EO)(2), fluorocarbon chain length n = 4, 6, 8) and sodium 1,4-bis(1H,1H,2H,2H-perfluoroalkyloxy)-1,4-dioxobutane-2-sulfonate (nFS(EO)(2), n = 4, 8). Visual observation and UV-vis spectral measurements with methyl orange as a reporter dye indicated a maximum water-to-surfactant molar ratio (W(0)) in the microemulsions, which was 60-80 for nFG(EO)(2) and 40-50 for nFG(EO)(2). Although it is normally expected that high solubilizing power requires long fluorocarbon surfactant chains, the shortest fluorocarbon 4FG(EO)(2) interestingly achieved the highest W(0) (80) transparent single-phase W/CO(2) microemulsion. In addition, a very rapid solubilization of loaded water into CO(2) was observed for 4FG(EO)(2) even at a high W(0) of ~80.

A guide to designing graphene-philic surfactants.

HYPOTHESIS: As compared to common aliphatic surfactants, increasing the number of pendant or incorporated aromatic groups in a surfactant is expected to offer significant enhancement in the affinity for graphene surfaces. The basis for enhanced graphene-philicity of aromatic surfactants is that they can develop appreciable π - π interactions with graphene. Furthermore, charged (anionic) surfactants are expected to confer electrostatic stabilization on surfactant-graphene composites. Hence, it is expected that anionic aromatic surfactants combine these two properties for effective stabilization of graphene dispersions in water. EXPERIMENTAL: The properties of two custom made graphene-compatible surfactants carrying two and three aromatic moieties in the hydrophobic tails, namely DC3Ph2 (sodium 1,4-dioxo-1,4-bis(3-phenylpropoxy)butane-2-sulfonate) and TC3Ph3 (sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3-phenylpropoxy)carbonyl) pentane-2-sulfonate) were compared with other common ionic commercial surfactants. Air-water (a/w) surface tension measurements were used to assess the surfactant adsorption and interfacial packing in the absence and presence of graphene. The surfactant coverage index for graphene (Ф) was calculated using surfactant headgroup areas derived from a/w surface tension data, chain volumes, and molecular fragment volumes from literature. FINDINGS: Increasing the number of aromatic groups and tails per surfactant was shown to increase the ability of surfactants to pack and fill space, as expressed by Ф. Comparison between the values of Ф for surfactants of different chain structure and architecture showed that the affinity for graphene increased with Ф. Hence, there is an implicit link between surfactant-graphene compatibility and the identity, chemical composition and architecture of the surfactant chains.

Super-efficient surfactant for stabilizing water-in-carbon dioxide microemulsions.

The fluorinated double-tailed glutarate anionic surfactant, sodium 1,5-bis[(1H,1H,2H,2H-perfluorodecyl)oxy]-1,5-dioxopentane-2-sulfonate (8FG(EO)(2)), was found to stabilize water-in-supercritical CO(2) microemulsions with high water-to-surfactant molar ratios (W(0)). Studies were carried out here to obtain detailed information on the phase stability and nanostructure of the microemulsions by using a high-pressure UV-vis dye probe and small-angle neutron scattering (SANS) measurements. The UV-vis spectra, with methyl orange as a reporter dye, indicated a maximum attainable W(0) of 60 at 45 and 75 °C, and SANS profiles indicated regular droplet swelling with a linear relationship between the water core nanodroplet radius and W(0). This represents the highest water solubilization reported to date for any water-in-CO(2) microemulsion. Further analysis of the SANS data indicated critical packing parameters for 8FG(EO)(2) at the microemulsion interface >1.34, representing approximately 1.1 times the value for common aerosol-OT in water-in-heptane microemulsions under equivalent conditions.

Low fluorine content CO2-philic surfactants.

The article addresses an important, and still unresolved question in the field of CO(2) science and technology: what is the minimum fluorine content necessary to obtain a CO(2)-philic surfactant? A previous publication (Langmuir 2002, 18, 3014) suggested there should be an ideal fluorination level: for optimization of possible process applications in CO(2), it is important to establish just how little F is needed to render a surfactant CO(2)-philic. Here, optimum chemical structures for water-in-CO(2) (w/c) microemulsion stabilization are identified through a systematic study of CO(2)-philic surfactant design based on dichain sulfosuccinates. High pressure small-angle neutron scattering (HP-SANS) measurements of reversed micelle formation in CO(2) show a clear relationship between F content and CO(2) compatibility of any given surfactant. Interestingly, high F content surfactants, having lower limiting aqueous surface tensions, γ(cmc), also have better performance in CO(2), as indicated by lower cloud point pressures, P(trans). The results have important implications for the rational design of CO(2)-philic surfactants helping to identify the most economic and efficient compounds for emerging CO(2) based fluid technologies.