Giant impurity effect on anomalous Hall effect of Mn3Sn.

Mn3Sn is an anomalous Hall effect (AHE) antiferromagnet that exhibits the hysteretic AHE in antiferromagnetic (AFM) phase at room temperature. We report that whisker Mn3Sn crystals grown by the flux method exhibit a non-hysteretic AHE at mid-to-low temperatures when the whisker Mn3Sn is surrounded by a thin layer of ferromagnetic Mn2-xSn. These crystals exhibit a hysteretic AHE above 275 K due to the spin alignment of the inverse triangular lattice, which is similar to other crystals. However, upon cooling the crystal, it exhibits a non-hysteretic AHE with a spiral AFM spin structure at 100-200 K. We concluded that the non-hysteretic AHE is induced at the interface of Mn2-xSn/Mn3Sn. We believe that the scalar-spin chirality in the spiral AFM phase of Mn3Sn, modulated by Mn2-xSn through the magnetic proximity effect, produces the AHE. This discovery opens a new avenue for tailoring the AHE by magnetic layers.

Superconductivity in High-Entropy Antimonide M1-xPtxSb (M = Equimolar Ru, Rh, Pd, and Ir).

The high-entropy concept was applied to the synthesis of transition-metal antimonides, M1-xPtxSb (M = equimolar Ru, Rh, Pd, and Ir). High-entropy antimonide samples crystallized in a pseudo-hexagonal NiAs-type crystal structure with a P63/mmc space group were successfully synthesized through a conventional solid-state reaction and subsequent quenching. A detailed investigation of the composition and equilibration conditions confirmed the reversible phase transition between a multiphase state at low temperature and an entropy-driven single-phase solid solution at high temperatures. Electrical resistivity, magnetization, and heat capacity measurements of single-phase M1-xPtxSb (x = 0.2) samples revealed a bulk superconducting transition at 2.15(2) K. This study demonstrates that the high-entropy concept provides numerous opportunities for the discovery of new functional materials such as superconductors.

Intensity Interference in a Coherent Spin-Polarized Electron Beam.

We investigate the intensity interference between pairs of electrons using a spin-polarized electron beam having a high polarization and a narrow energy width. We observe spin-dependent antibunching on the basis of coincident counts of electron pairs performed with a spin-polarized transmission electron microscope, which could control the spin-polarization without any changes in the electron optics. The experimental results show that the time correlation was only affected by the spin polarization, demonstrating that the antibunching is associated with fermionic statistics. The coherent spin-polarized electron beam facilitates the extraction of intrinsic quantum interference.

Creating electron phase holograms using femtosecond laser interference processing.

Recently, electron beams with structured phase fronts, such as electron vortex beams, have attracted considerable interest. Herein, we present a novel method of fabricating electron phase holograms using a femtosecond laser interference processing. A 35-nm-thick silicon membrane, corresponding to a phase shift of π for 200-keV electrons, was processed using single-shot laser irradiation, whereas processing such thin membranes with a focused ion beam milling technique would be very difficult. This rapid and efficient technique is expected to produce phase diffraction elements for practical applications in a wide range of electron optics fields.

Quantitative Operando Visualization of Electrochemical Reactions and Li Ions in All-Solid-State Batteries by STEM-EELS with Hyperspectral Image Analyses.

All-solid-state lithium-ion batteries (LIBs) are one of the promising candidates to overcome some issues of conventional LIBs with liquid electrolytes. However, high interfacial resistance of Li-ion transfer at the electrode/solid electrolyte limits their performance. Thus, it is important to clarify interfacial phenomena in a nanometer scale. Here, we present a new method to dynamically observe the Li-ion distribution and Co-ion electronic states in a LiCoO2 cathode of the all-solid-state LIB during charge and discharge reactions using operando scanning transmission electron microscopy (STEM) and electron energy-loss spectroscopy (EELS). By applying a hyperspectral image analysis of non-negative matrix factorization (NMF) to the STEM-EELS, we succeeded in clearly observing the quantitative Li-ion distribution in the operando condition. We found from the operando observation with NMF that the Li ions did not uniformly extract/insert during the charge/discharge reactions, and the activity of the electrochemical reaction depended on the Li-ion concentration in a pristine state. An electrochemically inactive region was formed about 10-20 nm near the LiCoO2/Li2O-Al2O3-TiO2-P2O5-based solid electrolyte interfaces. The STEM-EELS, electron diffraction, and Raman spectroscopy experimentally showed that the inactive region was a mixture of LiCoO2 and Co3O4, leading to the higher interfacial resistance of the Li-ion transfer because Co3O4 does not have pathways of Li-ion diffusion in its crystal.

Direct Observation of a Li-Ionic Space-Charge Layer Formed at an Electrode/Solid-Electrolyte Interface.

When two different materials come into contact, mobile carriers redistribute at the interface according to their potential difference. Such a charge redistribution is also expected at the interface between electrodes and solid electrolytes. The redistributed ions significantly affect the ion conduction through the interface. Thus, it is essential to determine the actual distribution of the ionic carriers and their potential to improve ion conduction. We succeeded in visualizing the ionic and potential profiles in the charge redistribution layer, or space-charge layer (SCL), formed at the interface between a Cu electrode and Li-conductive solid electrolyte using phase-shifting electron holography and spatially resolved electron energy-loss spectroscopy. These electron microscopy techniques clearly showed the Li-ionic SCL, which dropped by 1.3 V within a distance of 10 nm from the interface. These techniques could contribute to the development of next-generation electrochemical devices.

Development of silicon-on-insulator direct electron detector with analog memories in pixels for sub-microsecond imaging.

We have developed a high-speed recordable direct electron detector based on silicon-on-insulator technology. The detector has sixteen analog memories in each pixel to record sixteen images with sub-microsecond temporal resolution. A dedicated data acquisition system has also been developed to display and record the results on a personal computer. The performance of the direct electron detector as an image sensor is evaluated under electron irradiation with an energy of 30 keV in a low-voltage transmission electron microscope equipped with a photocathode electron gun. We demonstrate that the detector can record images at an exposure time of 100 ns and an interval of 900 ns.

Measuring the orbital angular momentum of electron vortex beams using a forked grating.

The present study experimentally examines how an electron vortex beam with orbital angular momentum (OAM) undergoes diffraction through a forked grating. The nth-order diffracted electron vortex beam after passing through a forked grating with a Burgers vector of 1 shows an OAM transfer of nℏ. Hence, the diffraction patterns become mirror asymmetric owing to the size difference between the electron beams. Such a forked grating, when used in combination with a pinhole located at the diffraction plane, could act as an analyzer to measure the OAM of input electrons.

Dynamic environmental transmission electron microscopy observation of platinum electrode catalyst deactivation in a proton-exchange-membrane fuel cell.

Spherical-aberration-corrected environmental transmission electron microscopy (AC-ETEM) was applied to study the catalytic activity of platinum/amorphous carbon electrode catalysts in proton-exchange-membrane fuel cells (PEMFCs). These electrode catalysts were characterized in different atmospheres, such as hydrogen and air, and a conventional high vacuum of 10(-5) Pa. A high-speed charge coupled device camera was used to capture real-time movies to dynamically study the diffusion and reconstruction of nanoparticles with an information transfer down to 0.1 nm, a time resolution below 0.2 s and an acceleration voltage of 300 kV. With such high spatial and time resolution, AC-ETEM permits the visualization of surface-atom behaviour that dominates the coalescence and surface-reconstruction processes of the nanoparticles. To contribute to the development of robust PEMFC platinum/amorphous carbon electrode catalysts, the change in the specific surface area of platinum particles was evaluated in hydrogen and air atmospheres. The deactivation of such catalysts during cycle operation is a serious problem that must be resolved for the practical use of PEMFCs in real vehicles. In this paper, the mechanism for the deactivation of platinum/amorphous carbon electrode catalysts is discussed using the decay rate of the specific surface area of platinum particles, measured first in a vacuum and then in hydrogen and air atmospheres for comparison.

Measurement and correction of TEM image distortion using arbitrary samples.

We have developed a method to quantitatively measure image distortion, one of the five Seidel aberrations, in transmission electron microscopes without using a standard sample with a known structure. Displacements of small local segments in an image due to image distortion of the intermediate and projection lens system are first measured by comparing images taken before and after a given shift at the first image plane of the objective lens. Then, the sum of the second partial derivatives, or the Laplacian, of the displacement field is measured, and the radial and azimuthal distortion parameters are determined from the measured results. We confirmed using numerically distorted images that the proposed method can measure the image distortion within a relative error ratio of 0.04 for a wide range of distortion amount from 0.1% to 5.0%. The distortion measurement and correction were confirmed to work correctly by using the experimental images, and the iterative measurement and correction procedure could reduce the distortion to a level where the average image displacement was < 0.05 pixels.

Phase Retrieval of Electron Rocking Curves using Total Variation and Total Squared Variation Regularizations.

In this study, a new method for the phase retrieval of electron rocking curves observed using convergent-beam electron diffraction, which is applicable to the determination of three-dimensional lattice displacement fields along the beam direction, is proposed. Total variation and total squared variation regularizations are introduced for phase retrieval to suppress overfitting to noise or background signals in the rocking curves and to reproduce the sparse characteristics of displacement fields, which exist only near lattice defects. The results show that the proposed algorithm is effective for rocking curves modulated by the dynamical effect of electron diffraction. The accuracy of phase reconstruction using the proposed method is also discussed. Phase retrieval of the experimental rocking curves obtained from a stacking fault in stainless steel is demonstrated.

Static Hydrophobic Cuprous Oxide Surface Fabricated via One-Step Laser-Induced Oxidation of a Copper Substrate.

In this study, we developed a one-step method for fabricating hydrophobic surfaces on copper (Cu) substrates. Cuprous oxide (Cu2O) with low free energy was successfully formed after low-fluence laser direct irradiation. The formation of Cu2O enhanced the hydrophobicity of the Cu substrate surface, and the contact angle linearly increased with the proportion of Cu2O. The Cu2O fabricated by low-fluence laser treatment showed the same crystal plane orientation as the pristine Cu substrate, implying an epitaxial growth of Cu2O on a Cu substrate.

Carbonization of a Molybdenum Substrate Surface and Nanoparticles by a One-Step Method of Femtosecond Laser Ablation in a Hexane Solution.

Molybdenum carbides (MoC and Mo2C) are being reported for various applications, for example, catalysts for sustainable energies, nonlinear materials for laser applications, protective coatings for improving tribological performance, and so on. A one-step method for simultaneously fabricating molybdenum monocarbide (MoC) nanoparticles (NPs) and MoC surfaces with a laser-induced periodic surface structure (LIPSS) was developed by using pulsed laser ablation of a molybdenum (Mo) substrate in hexane. Spherical NPs with an average diameter of 61 nm were observed by scanning electron microscopy. The X-ray diffraction pattern and electron diffraction (ED) pattern results indicate that a face-centered cubic MoC was successfully synthesized for the NPs and on the laser-irradiated area. Notably, the ED pattern suggests that the observed NPs are nanosized single crystals, and a carbon shell was observed on the surface of MoC NPs. The X-ray diffraction pattern of both MoC NPs and LIPSS surface indicates the formation of FCC MoC, agreeing with the results of ED. The results of X-ray photoelectron spectroscopy also showed the bonding energy attributed to Mo-C, and the sp2-sp3 transition was confirmed on the LIPSS surface. The results of Raman spectroscopy have also supported the formation of MoC and amorphous carbon structures. This simple synthesis method for MoC may provide new possibilities for preparing Mo x C-based devices and nanomaterials, which may contribute to the development of catalytic, photonic, and tribological fields.

Production of electron vortex beams carrying large orbital angular momentum using spiral zone plates.

We report the production of electron vortex beams carrying large orbital angular momentum (OAM) using micro-fabricated spiral zone plates. A series of the spherical waves, focussing onto different positions along the propagating direction of the electron beam, were observed. The nth order vortex beam has an OAM n times larger than that of the first-order vortex beam. We observed an electron vortex with an OAM up to in a high-order diffracted wave. A linear dependence of the diameter of the vortex beam on the OAM was observed, being consistent to numerical simulations.

Orbital angular momentum-resolved convergent-beam electron diffraction by the post-selected injection of electron beam.

Recent advances in the production of electron vortex beams carrying orbital angular momentum (OAM) offer unique opportunities to explore materials at the nanoscale level. We present a novel method for observing convergent-beam electron diffraction (CBED) patterns by using an electron vortex beam. In a transmission electron microscope, a series of electron vortex beams generated by a forked grating mask located above the specimen illuminate the specimen, and CBED patterns are imaged onto the observation plane of the microscope, selecting one of the electron vortex beams using an aperture located beneath the specimen. We demonstrate that the post-selection method yields the same OAM-resolved CBED patterns as when a single convergent electron beam is injected. The formation mechanism of the post-selected CBED is also discussed. This post-selection method is general and can be applied to electron energy-loss spectroscopy to probe multipole excitations using electron vortex beams.

Denoising of series electron holograms using tensor decomposition.

In this study, a noise-reduction technique for series low-dose electron holograms using tensor decomposition is demonstrated through simulation. We treated an entire dataset of the series holograms with Poisson noise as a third-order tensor, which is a stack of 2D holograms. The third-order tensor, which is decomposed into a core tensor and three factor matrices, is approximated as a lower-rank tensor using only noise-free principal components. This technique is applied to simulated holograms by assuming a p-n junction in a semiconductor sample. The peak signal-to-noise ratios of the holograms and the reconstructed phase maps have been improved significantly using tensor decomposition. Moreover, the proposed method was applied to a more practical situation of time-resolved in situ electron holography by considering a nonuniform fringe contrast and fringe drift relative to the sample. The accuracy and precision of the reconstructed phase maps were quantitatively evaluated to demonstrate its effectiveness for in situ experiments and low-dose experiments on beam-sensitive materials.

Performance of a silicon-on-insulator direct electron detector in a low-voltage transmission electron microscope.

The performance of a direct electron detector using silicon-on-insulator (SOI) technology in a low-voltage transmission electron microscope (LVTEM) is evaluated. The modulation transfer function and detective quantum efficiency of the detector are measured under backside illumination. The SOI-type detector is demonstrated to have high sensitivity and high efficiency for the direct detection of low-energy electrons. The detector is thus considered suitable for low-dose imaging in an LVTEM.

Observation of domain wall bimerons in chiral magnets.

Topological defects embedded in or combined with domain walls have been proposed in various systems, some of which are referred to as domain wall skyrmions or domain wall bimerons. However, the experimental observation of such topological defects remains an ongoing challenge. Here, using Lorentz transmission electron microscopy, we report the experimental discovery of domain wall bimerons in chiral magnet Co-Zn-Mn(110) thin films. By applying a magnetic field, multidomain structures develop, and simultaneously, chained or isolated bimerons arise as the localized state between the domains with the opposite in-plane components of net magnetization. The multidomain formation is attributed to magnetic anisotropy and dipolar interaction, and domain wall bimerons are stabilized by the Dzyaloshinskii-Moriya interaction. In addition, micromagnetic simulations show that domain wall bimerons appear for a wide range of conditions in chiral magnets with cubic magnetic anisotropy. Our results promote further study in various fields of physics.

Atom-column distinction by Kikuchi pattern observed by an aberration-corrected convergent electron probe.

Kikuchi patterns of an MgO crystal at the [110] incidence have been taken by a sub-angstrom electron beam focused on the single atom-column. A significant change in intensity has been observed in the 111 band; that is, the contrast in the central and side bands is reversed depending on the illuminated atom-column. The contrast reversal in the 111 band has been reproduced by multislice simulation using the frozen-phonon approach. The beam-position dependence of the 111 band intensity can be interpreted by electron channelling and the reciprocity theorem. The anomalous Kikuchi pattern can be a probe for identifying the illuminated atom-column, which is useful for column-by-column electron energy-loss spectroscopy and X-ray emission spectroscopy.