Different Scenarios of Autonomous Operation of an Environmental Sensor Node Using a Piezoelectric-Vibration-Based Energy Harvester.

This paper delves into the application of vibration-based energy harvesting to power environmental sensor nodes, a critical component of modern data collection systems. These sensor nodes play a crucial role in structural health monitoring, providing essential data on external conditions that can affect the health and performance of structures. We investigate the feasibility and efficiency of utilizing piezoelectric vibration energy harvesters to sustainably power environmental wireless sensor nodes on the one hand. On the other hand, we exploit different approaches to minimize the sensor node's power consumption and maximize its efficiency. The investigations consider various sensor node platforms and assess their performance under different voltage levels and broadcast frequencies. The findings reveal that optimized harvester designs enable real-time data broadcasting with short intervals, ranging from 1 to 3 s, expanding the horizons of environmental monitoring, and show that in case the system includes a battery as a backup plan, the battery's lifetime can be extended up to 9 times. This work underscores the potential of vibration energy harvesting as a viable solution for powering sensor nodes, enhancing their autonomy, and reducing maintenance costs in remote and challenging environments. It opens doors to broader applications of sustainable energy sources in environmental monitoring and data collection systems.

Establishment of a New Device for Electrical Stimulation of Non-Degenerative Cartilage Cells In Vitro.

In cell-based therapies for cartilage lesions, the main problem is still the formation of fibrous cartilage, caused by underlying de-differentiation processes ex vivo. Biophysical stimulation is a promising approach to optimize cell-based procedures and to adapt them more closely to physiological conditions. The occurrence of mechano-electrical transduction phenomena within cartilage tissue is physiological and based on streaming and diffusion potentials. The application of exogenous electric fields can be used to mimic endogenous fields and, thus, support the differentiation of chondrocytes in vitro. For this purpose, we have developed a new device for electrical stimulation of chondrocytes, which operates on the basis of capacitive coupling of alternating electric fields. The reusable and sterilizable stimulation device allows the simultaneous use of 12 cavities with independently applicable fields using only one main supply. The first parameter settings for the stimulation of human non-degenerative chondrocytes, seeded on collagen type I elastin-based scaffolds, were derived from numerical electric field simulations. Our first results suggest that applied alternating electric fields induce chondrogenic re-differentiation at the gene and especially at the protein level of human de-differentiated chondrocytes in a frequency-dependent manner. In future studies, further parameter optimizations will be performed to improve the differentiation capacity of human cartilage cells.

Materials and scaffolds in medical 3D printing and bioprinting in the context of bone regeneration.

The structural and functional repair of lost bone is still one of the biggest challenges in regenerative medicine. In many cases, autologous bone is used for the reconstruction of bone tissue; however, the availability of autologous material is limited, which always means additional stress to the patient. Due to this, more and more frequently various biocompatible materials are being used instead for bone augmentation. In this context, in order to ensure the structural function of the bone, scaffolds are implanted and fixed into the bone defect, depending on the medical indication. Nevertheless, for the surgeon, every individual clinical condition in which standardized scaffolds have to be aligned is challenging, and in many cases the alignment is not possible without limitations. Therefore, in the last decades, 3D printing (3DP) or additive manufacturing (AM) of scaffolds has become one of the most innovative approaches in surgery to individualize and improve the treatment of patients. Numerous biocompatible materials are available for 3DP, and various printing techniques can be applied, depending on the process conditions of these materials. Besides these conventional printing techniques, another promising approach in the context of medical AM is 3D bioprinting, a technique which makes it possible to print human cells embedded in special carrier substances to generate functional tissues. Even the direct printing into bone defects or lesions becomes possible. 3DP is already improving the treatment of patients, and has the potential to revolutionize regenerative medicine in future.

Microstructured zirconia surfaces modulate osteogenic marker genes in human primary osteoblasts.

In dentistry, zirconia has been used since the early 1990s for endodontic posts, more recently for implant abutments and frameworks for fixed dental prostheses. Zirconia is biocompatible and mechanically strong enough to serve as implant material for oral implants. Although several zirconia implant systems are available, currently the scientific and clinical data for zirconia implants are not sufficient to recommend them for routine clinical use. Here the influence of microstructured yttria-stabilized zirconia (YZ) on human primary osteoblast (HOB) behavior was determined. YZ surfaces were treated by sandblasting (YZ-S), acid etching (YZ-SE) and additionally heat treatment (YZ-SEH). Morphological changes of HOB were determined by scanning electron microscopy. Actin cytoskeleton was investigated by laser scanning microscopy and analyzed by novel actin quantification software. Differentiation of HOB was determined by real time RT-PCR. Improved mechanical interlocking of primary HOB into the porous microstructure of the acid etched and additionally heat treated YZ-surfaces correlates with drastically increased osteocalcin (OCN) gene expression. In particular, OCN was considerably elevated in primary HOB after 3 days on YZ-SE (13-fold) as well as YZ-SEH (12-fold) surfaces. Shorter actin filaments without any favored orientation on YZ-SE and YZ-SEH surfaces are associated with higher roughness (Ra) values. Topographically modified yttria-stabilized zirconia is a likely material for dental implants with cell stimulating properties achieving or actually exceeding those of titanium.

Machine Learning Classification of Self-Organized Surface Structures in Ultrashort-Pulse Laser Processing Based on Light Microscopic Images.

In ultrashort-pulsed laser processing, surface modification is subject to complex laser and scanning parameter studies. In addition, quality assurance systems for monitoring surface modification are still lacking. Automated laser processing routines featuring machine learning (ML) can help overcome these limitations, but they are largely absent in the literature and still lack practical applications. This paper presents a new methodology for machine learning classification of self-organized surface structures based on light microscopic images. For this purpose, three application-relevant types of self-organized surface structures are fabricated using a 300 fs laser system on hot working tool steel and stainless-steel substrates. Optical images of the hot working tool steel substrates were used to learn a classification algorithm based on the open-source tool Teachable Machine from Google. The trained classification algorithm achieved very high accuracy in distinguishing the surface types for the hot working steel substrate learned on, as well as for surface structures on the stainless-steel substrate. In addition, the algorithm also achieved very high accuracy in classifying the images of a specific structure class captured at different optical magnifications. Thus, the methodology proposed represents a simple and robust automated classification of surface structures that can be used as a basis for further development of quality assurance systems, automated process parameter recommendation, and inline laser parameter control.

Influence of the Volatility of Solvent on the Reproducibility of Droplet Formation in Pharmaceutical Inkjet Printing.

Drop-on-demand (DOD) inkjet printing enables exact dispensing and positioning of single droplets in the picoliter range. In this study, we investigate the long-term reproducibility of droplet formation of piezoelectric inkjet printed drug solutions using solvents with different volatilities. We found inkjet printability of EtOH/ASA drug solutions is limited, as there is a rapid forming of drug deposits on the nozzle of the printhead because of fast solvent evaporation. Droplet formation of c = 100 g/L EtOH/ASA solution was affected after only a few seconds by little drug deposits, whereas for c = 10 g/L EtOH/ASA solution, a negative affection was observed only after t = 15 min, while prominent drug deposits form at the printhead tip. Due to the creeping effect, the crystallizing structures of ASA spread around the nozzle but do not clog it necessarily. When there is a negative affection, the droplet trajectory is affected the most, while the droplet volume and droplet velocity are influenced less. In contrast, no formation of drug deposits could be observed for highly concentrated, low volatile DMSO-based drug solution of c = 100 g/L even after a dispensing time of t = 30 min. Therefore, low volatile solvents are preferable to highly volatile solvents to ensure a reproducible droplet formation in long-term inkjet printing of highly concentrated drug solutions. Highly volatile solvents require relatively low drug concentrations and frequent printhead cleaning. The findings of this study are especially relevant when high droplet positioning precision is desired, e.g., drug loading of microreservoirs or drug-coating of microneedle devices.

Simulating the mechanical stimulation of cells on a porous hydrogel scaffold using an FSI model to predict cell differentiation.

3D-structured hydrogel scaffolds are frequently used in tissue engineering applications as they can provide a supportive and biocompatible environment for the growth and regeneration of new tissue. Hydrogel scaffolds seeded with human mesenchymal stem cells (MSCs) can be mechanically stimulated in bioreactors to promote the formation of cartilage or bone tissue. Although in vitro and in vivo experiments are necessary to understand the biological response of cells and tissues to mechanical stimulation, in silico methods are cost-effective and powerful approaches that can support these experimental investigations. In this study, we simulated the fluid-structure interaction (FSI) to predict cell differentiation on the entire surface of a 3D-structured hydrogel scaffold seeded with cells due to dynamic compressive load stimulation. The computational FSI model made it possible to simultaneously investigate the influence of both mechanical deformation and flow of the culture medium on the cells on the scaffold surface during stimulation. The transient one-way FSI model thus opens up significantly more possibilities for predicting cell differentiation in mechanically stimulated scaffolds than previous static microscale computational approaches used in mechanobiology. In a first parameter study, the impact of the amplitude of a sinusoidal compression ranging from 1% to 10% on the phenotype of cells seeded on a porous hydrogel scaffold was analyzed. The simulation results show that the number of cells differentiating into bone tissue gradually decreases with increasing compression amplitude, while differentiation into cartilage cells initially multiplied with increasing compression amplitude in the range of 2% up to 7% and then decreased. Fibrous cell differentiation was predicted from a compression of 5% and increased moderately up to a compression of 10%. At high compression amplitudes of 9% and 10%, negligible areas on the scaffold surface experienced high stimuli where no cell differentiation could occur. In summary, this study shows that simulation of the FSI system is a versatile approach in computational mechanobiology that can be used to study the effects of, for example, different scaffold designs and stimulation parameters on cell differentiation in mechanically stimulated 3D-structured scaffolds.

A Printing Strategy for Embedding Conductor Paths into FFF Printed Parts.

A novel approach to manufacture components with integrated conductor paths involves embedding and sintering an isotropic conductive adhesive (ICA) during fused filament fabrication (FFF). However, the molten plastic is deposited directly onto the adhesive path which causes an inhomogeneous displacement of the uncured ICA. This paper presents a 3D printing strategy to achieve a homogeneous cross-section of the conductor path. The approach involves embedding the ICA into a printed groove and sealing it with a wide extruded plastic strand. Three parameter studies are conducted to obtain a consistent cavity for uniform formation of the ICA path. Specimens made of polylactic acid (PLA) with embedded ICA paths are printed and evaluated. The optimal parameters include a groove printed with a layer height of 0.1 mm, depth of 0.4 mm, and sealed with a PLA strand of 700 µm diameter. This resulted in a conductor path with a homogeneous cross-section, measuring 660 µm ± 22 µm in width (relative standard deviation: 3.3%) and a cross-sectional area of 0.108 mm2 ± 0.008 mm2 (relative standard deviation 7.2%). This is the first study to demonstrate the successful implementation of a printing strategy for embedding conductive traces with a homogeneous cross-sectional area in FFF 3D printing.

Correction: 3D printed and stimulus responsive drug delivery systems based on synthetic polyelectrolyte hydrogels manufactured via digital light processing.

Correction for '3D printed and stimulus responsive drug delivery systems based on synthetic polyelectrolyte hydrogels manufactured via digital light processing' by Sonja Vaupel et al., J. Mater. Chem. B, 2023, DOI: https://doi.org/10.1039/d3tb00285c.

Volumetric mass density measurements of mesenchymal stem cells in suspension using a density meter.

To use regeneratively active cells for cell therapeutic applications, the cells must be isolated from their resident tissues. Different isolation procedures subject these cells to varying degrees of mechanical strain, which can affect the yield of cell number and viability. Knowledge of cell volumetric mass density is important for experimental and numerical optimization of these procedures. Although methods for measuring cell volumetric mass density already exist, they either consume much time and cell material or require a special setup. Therefore, we developed a user-friendly method that is based on the use of readily available instrumentation. The newly developed method is predicated on the linear relationship between the volumetric mass density of the cell suspension and the volumetric mass density, number, and diameter of the cells in the suspension. We used this method to determine the volumetric mass density of mesenchymal stem cells (MSCs) and compared it to results from the established density centrifugation.

3D printed and stimulus responsive drug delivery systems based on synthetic polyelectrolyte hydrogels manufactured via digital light processing.

Hydrogels are three-dimensional hydrophilic polymeric networks absorbing up to and even more than 90 wt% of water. These superabsorbent polymers retain their shape during the swelling process while enlarging their volume and mass. In addition to their swelling behavior, hydrogels can possess other interesting properties, such as biocompatibility, good rheological behavior, or even antimicrobial activity. This versatility qualifies hydrogels for many medical applications, especially drug delivery systems. As recently shown, polyelectrolyte-based hydrogels offer beneficial properties for long-term and stimulus-responsive applications. However, the fabrication of complex structures and shapes can be difficult to achieve with common polymerization methods. This obstacle can be overcome by the use of additive manufacturing. 3D printing technology is gaining more and more attention as a method of producing materials for biomedical applications and medical devices. Photopolymerizing 3D printing methods offer superior resolution and high control of the photopolymerization process, allowing the fabrication of complex and customizable designs while being less wasteful. In this work, novel synthetic hydrogels, consisting of [2-(acryloyloxy) ethyl]trimethylammonium chloride (AETMA) as an electrolyte monomer and poly(ethylene glycol)-diacrylate (PEGDA) as a crosslinker, 3D printed via Digital Light Processing (DLP) using a layer height of 100 µm, are reported. The hydrogels obtained showed a high swelling degree q∞m,t ∼ 12 (24 h in PBS; pH 7; 37 °C) and adjustable mechanical properties with high stretchability (εmax ∼ 300%). Additionally, we embedded the model drug acetylsalicylic acid (ASA) and investigated its stimulus-responsive drug release behaviour in different release media. The stimulus responsiveness of the hydrogels is mirrored in their release behavior and could be exploited in triggered as well as sequential release studies, demonstrating a clear ion exchange behavior. The received 3D-printed drug depots could also be printed in complex hollow geometry, exemplarily demonstrated via an individualized frontal neo-ostium implant prototype. Consequently, a drug-releasing, flexible, and swellable material was obtained, combining the best of both worlds: the properties of hydrogels and the ability to print complex shapes.

Influence of Haunch Geometry and Additional Steel Reinforcement on Load Carrying Capacity of Reinforced Concrete Box Culvert.

The culverts are used to safely convey water under railways, highways, and overpasses. They are utilized in drainage areas or water channels and in areas where the bearing capacity of soil is low. The design and construction of this crucial infrastructure need to be improved to meet contemporary demands of reliability and affordability. Precast reinforced box culverts are popular alternatives as they ensure strength, durability, rigidity, and economy. This research seeks to develop an effective and affordable design improvement procedure for a precast box culvert using modern numerical tools. The Finite Element Method (FEM) based approach is used in studying the effects of haunch geometry and additional steel reinforcement on the load-bearing capacity of box culverts. A conventional box culvert is analyzed to create the numerical models in the Abaqus FEM code and to investigate the load-bearing capacity of culverts with an expanded span. The outcomes of the study reveal the critical places for stress concentration as well as the location of maximum damage. It is found that haunch geometry and additional reinforcement at these critical places significantly affect the load-carrying capacity of a culvert. From the comparison of capacity curves of models with and without haunches and diagonal reinforcement, it is found that a 25% increase in load-carrying capacity is achievable with the recommended changes. The proposed design improvement technique can be employed for the cost-effective and safe design of a concrete box culvert with larger span lengths and high water-flowing capacities. The findings of this study are expected to assist practitioners in strength enhancement tasks of box culverts for increased structural stability and drainage efficiency.

How droplets move on laser-structured surfaces: Determination of droplet adhesion forces on nano- and microstructured surfaces.

HYPOTHESIS: Lateral adhesion forces are a fundamental property of liquid-solid interactions and a key aspect of dynamic droplet mobility. But, commonly applied conventional wetting analysis is limited to static and quasi-static methods and cannot resolve dynamic and spatial liquid-solid interactions. However, droplet mobility is assumed to be affected by chemical and topographic surface inhomogeneities introduced by femtosecond laser treatment. EXPERIMENTS: In this study, we used a customized droplet adhesion force instrument to determine lateral adhesion forces on various femtosecond laser-structured surface designs to obtain a deeper understanding of the dynamic droplet motion with regard to chemical and topographic surface features. FINDINGS: We show that the droplet motion was highly affected by the chemical and topographical surface design and local inhomogeneities. The droplet mobility on femtosecond laser-structured surfaces could be classified into a static, a transfer, and a kinetic regime, which is essential for designing surfaces with extreme wetting characteristics and a wide range of scientific and industrial processes. Furthermore, with proper tailoring of surface structures and chemical modification, we were able to provoke adhesion forces on self-organized laser microstructures similar to those found on the natural lotus leaves.

Influence of PEGDA Molecular Weight and Concentration on the In Vitro Release of the Model Protein BSA-FITC from Photo Crosslinked Systems.

Novel 3D printing techniques enable the development of medical devices with drug delivery systems that are tailored to the patient in terms of scaffold shape and the desired pharmaceutically active substance release. Gentle curing methods such as photopolymerization are also relevant for the incorporation of potent and sensitive drugs including proteins. However, retaining the pharmaceutical functions of proteins remains challenging due to the possible crosslinking between the functional groups of proteins, and the used photopolymers such as acrylates. In this work, the in vitro release of the model protein drug, albumin-fluorescein isothiocyanate conjugate (BSA-FITC) from differently composed, photopolymerized poly(ethylene) glycol diacrylate (PEGDA), an often employed, nontoxic, easily curable resin, was investigated. Different PEGDA concentrations in water (20, 30, and 40 wt %) and their different molecular masses (4000, 10,000, and 20,000 g/mol) were used to prepare a protein carrier with photopolymerization and molding. The viscosity measurements of photomonomer solutions revealed exponentially increasing values with increasing PEGDA concentration and molecular mass. Polymerized samples showed increasing medium uptake with an increasing molecular mass and decreasing uptake with increasing PEGDA content. Therefore, the modification of the inner network resulted in the most swollen samples (20 wt %) also releasing the highest amount of incorporated BSA-FITC for all PEGDA molecular masses.

Micro Injection Molding of Drug-Loaded Round Window Niche Implants for an Animal Model Using 3D-Printed Molds.

A novel approach for the long-term medical treatment of the inner ear is the diffusion of drugs through the round window membrane from a patient-individualized, drug-eluting implant, which is inserted in the middle ear. In this study, drug-loaded (10 wt% Dexamethasone) guinea pig round window niche implants (GP-RNIs, ~1.30 mm × 0.95 mm × 0.60 mm) were manufactured with high precision via micro injection molding (µIM, Tmold = 160 °C, crosslinking time of 120 s). Each implant has a handle (~3.00 mm × 1.00 mm × 0.30 mm) that can be used to hold the implant. A medical-grade silicone elastomer was used as implant material. Molds for µIM were 3D printed from a commercially available resin (TG = 84 °C) via a high-resolution DLP process (xy resolution of 32 µm, z resolution of 10 µm, 3D printing time of about 6 h). Drug release, biocompatibility, and bioefficacy of the GP-RNIs were investigated in vitro. GP-RNIs could be successfully produced. The wear of the molds due to thermal stress was observed. However, the molds are suitable for single use in the µIM process. About 10% of the drug load (8.2 ± 0.6 µg) was released after 6 weeks (medium: isotonic saline). The implants showed high biocompatibility over 28 days (lowest cell viability ~80%). Moreover, we found anti-inflammatory effects over 28 days in a TNF-α-reduction test. These results are promising for the development of long-term drug-releasing implants for human inner ear therapy.

3D printing of piezoelectric and bioactive barium titanate-bioactive glass scaffolds for bone tissue engineering.

Bone healing is a complex process orchestrated by various factors, such as mechanical, chemical and electrical cues. Creating synthetic biomaterials that combine several of these factors leading to tailored and controlled tissue regeneration, is the goal of scientists worldwide. Among those factors is piezoelectricity which creates a physiological electrical microenvironment that plays an important role in stimulating bone cells and fostering bone regeneration. However, only a limited number of studies have addressed the potential of combining piezoelectric biomaterials with state-of-the-art fabrication methods to fabricate tailored scaffolds for bone tissue engineering. Here, we present an approach that takes advantage of modern additive manufacturing techniques to create macroporous biomaterial scaffolds based on a piezoelectric and bioactive ceramic-crystallised glass composite. Using binder jetting, scaffolds made of barium titanate and 45S5 bioactive glass are fabricated and extensively characterised with respect to their physical and functional properties. The 3D-printed ceramic-crystallised glass composite scaffolds show both suitable mechanical strength and bioactive behaviour, as represented by the accumulation of bone-like calcium phosphate on the surface. Piezoelectric scaffolds that mimic or even surpass bone with piezoelectric constants ranging from 1 to 21 pC/N are achieved, depending on the composition of the composite. Using MC3T3-E1 osteoblast precursor cells, the scaffolds show high cytocompatibility coupled with cell attachment and proliferation, rendering the barium titanate/45S5 ceramic-crystallised glass composites promising candidates for bone tissue engineering.

Mouldability of Additively Manufactured Attachments on Multipoint Tools.

Enhanced multipoint moulding with additive attachments (EMMA) is a process combining vacuum-assisted multipoint moulding (VAMM) and additively manufactured moulding attachments for carbon fibre reinforced plastics (CFRP) component production. The aim of this initial study is to investigate the mouldability of the additively manufactured attachments on the multipoint tool. For this purpose, two different test specimens were defined, the VAMM machine was adjusted, the attachments were additively built with the robot on the curved silicone interpolation layer and lastly, the CFRP specimens were moulded. The fabrication results were analysed with surface comparisons to check that there was no displacement of the attachments during moulding. A visual evaluation of the manufactured components was carried out, and the overall dimensional accuracy was assessed by comparing the surface with the target geometry. The results showed a very good agreement between the shapes before and after the moulding and thus prove that the attachments were not postponed in the moulding process. The optical evaluation confirms good moulding results for the parts manufactured with the enhanced multipoint moulding with additive attachments. Moreover, the evaluation shows that the major parts of the specimens comply with the permissible tolerance of t = 6 mm defined in ISO 20457. To the authors' best knowledge, this is the first study that has investigated the entire EMMA process and systematically proved the mouldability of the additively manufactured attachments on multipoint tools.

Comparison of Conventional and Robotic Fused Filament Fabrication on Silicone Build Plates.

The objective of this study is the investigation of the transferability of the material extrusion process from conventional to robotic fabrication on silicone build plates for use in Enhanced Multipoint Moulding with Additive Attachments. Therefore, the study is based on two series of experiments. The first series of tests used a conventional plant extended by a silicone construction platform. In comparison, a six-axis industrial robot was chosen to produce the test specimens in the second series of tests. The comparisons of adhesion strengths and relative shape deviations are used to validate the transferability. The results of the tests show a very good transferability of the process from conventional to robotic production. Whilst angular specimen geometries can be transferred directly, for round specimen geometries, the results show a need for further adaptation to the robot kinematics. The round specimen geometries showed deviations in the surface quality caused by an over-extrusion in the robotic manufacturing. This over-extrusion results from the slicing process in combination with the robot control and may be avoided through further optimisation of the process parameters. Overall, to the best of our knowledge, this study is the first that successfully demonstrates the transfer of Fused Filament Fabrication (FFF) from a conventional system to manufacturing using robots on silicone build plates for the use in Enhanced Multipoint Moulding with Additive Attachments.

Interactive effects of ZnO nanoparticles and temperature on molecular and cellular stress responses of the blue mussel Mytilus edulis.

Temperature is an important abiotic factor that modulates all aspects of ectotherm physiology, including sensitivity to pollutants. Nanoparticles are emerging pollutants in coastal environments, and their potential to cause toxicity in marine organisms is a cause for concern. Here we studied the interactive effects of temperature (including seasonal and experimental warming) on sublethal toxicity of ZnO nanoparticles (nano-ZnO) in a model marine bivalve, the blue mussel Mytilus edulis. Molecular markers were used to assess the pollutant-induced cellular stress responses in the gills and the digestive gland of mussels exposed for 21 days to 10 µg l-1 and 100 µg l-1 of nano-ZnO or dissolved Zn under different temperature regimes including ambient temperature (10 °C and 15 °C in winter and summer, respectively) or experimental warming (+5 °C). Exposure to high concentration (100 µg l-1) of nano-ZnO caused oxidative injury to proteins and lipids and induced a marked apoptotic response indicated by increased transcript levels of apoptosis-related genes p53, caspase 3 and the MAPK pathway (JNK and p38) and decreased mRNA expression of anti-apoptotic Bcl-2. No significant induction of inflammatory cytokine-related response (TGF-ß and NF-κB) of tissues was observed in nano-ZnO exposed-mussels. Furthermore, the oxidative injury and apoptotic response could differentiate the effects of nano-ZnO from those of dissolved Zn in the mussels. This study revealed that oxidative stress and stress-related transcriptional responses to nano-ZnO were strongly modified by warming and season in the mussels. No single biomarker could be shown to consistently respond to nano-ZnO in all experimental groups, which implies that multiple biomarkers are needed to assess nano-ZnO toxicity to marine organisms under the variable environmental conditions of coastal habitats.

3D printed gelatin/decellularized bone composite scaffolds for bone tissue engineering: Fabrication, characterization and cytocompatibility study.

Three-dimensional (3D) printing technology enables the design of personalized scaffolds with tunable pore size and composition. Combining decellularization and 3D printing techniques provides the opportunity to fabricate scaffolds with high potential to mimic native tissue. The aim of this study is to produce novel decellularized bone extracellular matrix (dbECM)-reinforced composite-scaffold that can be used as a biomaterial for bone tissue engineering. Decellularized bone particles (dbPTs, ∼100 â€‹µm diameter) were obtained from rabbit femur and used as a reinforcement agent by mixing with gelatin (GEL) in different concentrations. 3D scaffolds were fabricated by using an extrusion-based bioprinter and crosslinking with microbial transglutaminase (mTG) enzyme, followed by freeze-drying to obtain porous structures. Fabricated 3D scaffolds were characterized morphologically, mechanically, and chemically. Furthermore, MC3T3-E1 mouse pre-osteoblast cells were seeded on the dbPTs reinforced GEL scaffolds (GEL/dbPTs) and cultured for 21 days to assess cytocompatibility and cell attachment. We demonstrate the 3D-printability of dbPTs-reinforced GEL hydrogels and the achievement of homogenous distribution of the dbPTs in the whole scaffold structure, as well as bioactivity and cytocompatibility of GEL/dbPTs scaffolds. It was shown that Young's modulus and degradation rate of scaffolds were enhanced with increasing dbPTs content. Multiphoton microscopy imaging displayed the interaction of cells with dbPTs, indicating attachment and proliferation of cells around the particles as well as into the GEL-particle hydrogels. Our results demonstrate that GEL/dbPTs hydrogel formulations have potential for bone tissue engineering.