Effectiveness of occlusal splints and low-level laser therapy on myofascial pain.

The present study was designed to evaluate the effects of low-level laser (Nd:YAG) therapy and occlusal splints in patients with signs and symptoms of temporomandibular disorders (TMD) characterized with myofascial pain (MP). A total of 30 patients were selected after being diagnosed with MP according to the Research Diagnostic Criteria for Temporomandibular Disorders (RDC/TDM). The patients were divided into three groups. The first group was occlusal splint (OS) group A (n = 10), the second was low-level laser therapy (LLLT) group B (n = 10), and the last group C was placebo (n = 10). LLLT (1,064 nm, 8 j/cm(2), 250 mW, Fotona) was applied to the patients in the study group once a day for 10 days, for a total of ten sessions. The same parameters and application times were used for placebo group, but the patients were not irradiated. The application was on the trigger points. The patients in the OS group were instructed to wear occlusal splints 12 h/day for 3 weeks. Functional examination was based on RDC/TDM, and pressure pain values were obtained with the Visual Analog Scale. Comparisons were made between the groups before and after the treatment according to Wilcoxon, Mann-Whitney U, and Kruskal-Wallis tests. The pain score values decreased significantly after both LLLT (p < 0.05) and occlusal splint therapy (p < 0.05) compared to placebo group (p < 0.05). There was no significant difference between LLLT and OS groups after treatment (p > 0.05). OS and LLLT are effective for decreasing MP. In addition, this particular type of LLLT is as effective as occlusal splint for pain relief.

Effects of edentulism on mandibular morphology: evaluation of panoramic radiographs.

PURPOSE: The objective of this study was to evaluate morphological changes of the mandible in edentulous and dentate subjects using panoramic radiographs. MATERIALS AND METHODS: Panoramic radiographs were divided into the following three groups: Group I (completely edentulous group), Group II (old dentate group) and Group III (young dentate group). The research parameters of gonial angle, condylar height, ramus height, ramus notch depth, and antegonial notch depth were measured on panoramic radiographs. The Kruskal-Wallis statistical test was used to determine significant differences in mandibular morphological parameters among the three groups. The Mann-Whitney U test was used to compare the subgroups. RESULTS: Significant differences were found only in ramus height between three groups. According to the Mann-Whitney U test, a significant difference was exhibited among Groups I and II in the ramus height parameter. No significant differences were found in the gonial angle, condylar height, ramus notch depth, or antegonial notch depth when comparing the young dentate, old dentate, and completely edentulous subjects. CONCLUSIONS: Significant differences were found only in ramus height between the groups. Ramus height may be an indicator that changed by years and tooth loss. It must be considered that ramus height can be decreased in edentulism.

Bond strength of resin cement to zirconia ceramic with different surface treatments.

Zirconia-based ceramics offer strong restorations in dentistry, but the adhesive bond strength of resin cements to such ceramics is not optimal. This study evaluated the influence of surface treatments on the bond strength of resin cement to yttrium-stabilized tetragonal zirconia (Y-TZP) ceramic. Seventy-five plates of Y-TZP ceramic were randomly assigned to five groups (n = 15) according to the surface treatments [airborne particle abrasion, neodymium-doped yttrium aluminum garnet (Nd:YAG) laser irradiation (Fidelis Plus 3, Fotona; 2 W, 200 mJ, 10 Hz, with two different pulse durations 180 or 320 µs), glaze applied, and then 9.5 % hydrofluoric acid gel conditioned, control]. One specimen from each group was randomly selected, and specimens were evaluated with x-ray diffraction and SEM analysis. The resin cement (Clearfil Esthetic Cement, Kuraray) was adhered onto the zirconia surfaces with its corresponding adhesive components. Shear bond strength of each sample was measured using a universal testing machine at a crosshead speed of 1 mm/min. Bond strengths were analyzed through one-way ANOVA/Tukey tests. Surface treatments significantly modified the topography of the Y-TZP ceramic. The Nd:YAG laser-irradiated specimens resulted in both increased surface roughness and bond strength of the resin cement. The highest surface roughness and bond strength values were achieved with short pulse duration. Nd:YAG laser irradiation increased both surface roughness of Y-TZP surfaces and bond strength of resin cement to the zirconia surface.

Does the Seating Force Affect the Shear Bond Strength of Brackets? An InVitro Study.

OBJECTIVE: The purpose of this study was to observe two different seating forces on conventional and self-ligating brackets using shear bond strength (SBS). METHODS: The study material consisted of 48 recently extracted human premolars divided into four groups: Group I, conventional bracket (Master series, AO) 100 g seating force applied; Group II, conventional bracket (Master series, AO) 200 g seating force applied; Group III, self-ligating bracket (Empower, AO) 100 g seating force applied; and Group IV, self-ligating bracket (Empower, AO) 200 g seating force applied. All teeth were bonded with Transbond XT by the same operator. Following the bonding procedure, all teeth were stored in deionized water at 37°C for 30 days, and they were thermal cycled. A universal testing machine was used to obtain the SBS records. The Kruskal-Wallis statistical test was used to determine the significant differences in SBS between the four groups, and the Mann-Whitney U test with Bonferroni correction was used to compare the subgroups. RESULTS: The mean shear bond strength was 15.70 MPa for Group I, 13.97 MPa for Group II, 8.38 MPa for Group III, and 8.31 MPa for Group IV. Significant differences in the SBS values were recorded between the self-ligating groups and conventional bracket groups. Seating forces on the brackets did not show any differences among the groups. CONCLUSION: Within the limitations in this study, 100 g and 200 g forces can be applied because both seating forces showed acceptable SBS results.

Shear bond strength of indirect composite material to monolithic zirconia.

PURPOSE: This study aimed to evaluate the effect of surface treatments on bond strength of indirect composite material (Tescera Indirect Composite System) to monolithic zirconia (inCoris TZI). MATERIALS AND METHODS: Partially stabilized monolithic zirconia blocks were cut into with 2.0 mm thickness. Sintered zirconia specimens were divided into different surface treatment groups: no treatment (control), sandblasting, glaze layer & hydrofluoric acid application, and sandblasting + glaze layer & hydrofluoric acid application. The indirect composite material was applied to the surface of the monolithic zirconia specimens. Shear bond strength value of each specimen was evaluated after thermocycling. The fractured surface of each specimen was examined with a stereomicroscope and a scanning electron microscope to assess the failure types. The data were analyzed using one-way analysis of variance (ANOVA) and Tukey LSD tests (α=.05). RESULTS: Bond strength was significantly lower in untreated specimens than in sandblasted specimens (P<.05). No difference between the glaze layer and hydrofluoric acid application treated groups were observed. However, bond strength for these groups were significantly higher as compared with the other two groups (P<.05). CONCLUSION: Combined use of glaze layer & hydrofluoric acid application and silanization are reliable for strong and durable bonding between indirect composite material and monolithic zirconia.