Directive giant upconversion by supercritical bound states in the continuum.

Photonic bound states in the continuum (BICs), embedded in the spectrum of free-space waves1,2 with diverging radiative quality factor, are topologically non-trivial dark modes in open-cavity resonators that have enabled important advances in photonics3,4. However, it is particularly challenging to achieve maximum near-field enhancement, as this requires matching radiative and non-radiative losses. Here we propose the concept of supercritical coupling, drawing inspiration from electromagnetically induced transparency in near-field coupled resonances close to the Friedrich-Wintgen condition2. Supercritical coupling occurs when the near-field coupling between dark and bright modes compensates for the negligible direct far-field coupling with the dark mode. This enables a quasi-BIC field to reach maximum enhancement imposed by non-radiative loss, even when the radiative quality factor is divergent. Our experimental design consists of a photonic-crystal nanoslab covered with upconversion nanoparticles. Near-field coupling is finely tuned at the nanostructure edge, in which a coherent upconversion luminescence enhanced by eight orders of magnitude is observed. The emission shows negligible divergence, narrow width at the microscale and controllable directivity through input focusing and polarization. This approach is relevant to various physical processes, with potential applications for light-source development, energy harvesting and photochemical catalysis.

Integration of stimulated Raman gain and stimulated Raman losses detection modes in a single nonlinear microscope.

This work addresses some key challenges in the fields of bio and nanophotonics by stimulated Raman microscopy. We present the design and the implementation of a femtosecond stimulated Raman scattering microscope, equipped with three femtosecond laser sources, which allows the coexistence of stimulated Raman gain (SRG) and stimulate Raman losses (SRL) detection modes in a single microscopy setup and to generate images of the same region in succession, without adding or removing components. In order to demonstrate the switching between the two detection modes, SRL and SRG images of polystyrene beads are acquired and the images quality are evaluated and compared.

Editorial for the Special Issue on Micro/Nanophotonic Devices in Europe.

Photonics has often been defined as the key technology of the 21st century [...].

An Introduction to Nonlinear Integrated Photonics Devices: Nonlinear Effects and Materials.

The combination of integrated optics technologies with nonlinear photonics, which has led to the growth of nonlinear integrated photonics, has also opened the way to groundbreaking new devices and applications. Here we introduce the main physical processes involved in nonlinear photonics applications, and we discuss the fundaments of this research area, starting from traditional second-order and third-order phenomena and going to ultrafast phenomena. The applications, on the other hand, have been made possible by the availability of suitable materials, with high nonlinear coefficients, and/or by the design of guided-wave structures, which can enhance the material's nonlinear properties. A summary of the most common nonlinear materials is presented, together with a discussion of the innovative ones. The discussion of fabrication processes and integration platforms is the subject of a companion article, also submitted for publication in this journal. There, several examples of nonlinear photonic integrated devices to be employed in optical communications, all-optical signal processing and computing, or quantum optics are shown, too. We aimed at offering a broad overview, even if, certainly, not exhaustive. We hope that the overall work could provide guidance for those who are newcomers to this field and some hints to the interested researchers for a more detailed investigation of the present and future development of this hot and rapidly growing field.

An Introduction to Nonlinear Integrated Photonics: Structures and Devices.

The combination of integrated optics technologies with nonlinear photonics, which has led to growth of nonlinear integrated photonics, has also opened the way to groundbreaking new devices and applications. In a companion paper also submitted for publication in this journal, we introduce the main physical processes involved in nonlinear photonics applications and discuss the fundaments of this research area. The applications, on the other hand, have been made possible by availability of suitable materials with high nonlinear coefficients and/or by design of guided-wave structures that can enhance a material's nonlinear properties. A summary of the traditional and innovative nonlinear materials is presented there. Here, we discuss the fabrication processes and integration platforms, referring to semiconductors, glasses, lithium niobate, and two-dimensional materials. Various waveguide structures are presented. In addition, we report several examples of nonlinear photonic integrated devices to be employed in optical communications, all-optical signal processing and computing, or in quantum optics. We aimed at offering a broad overview, even if, certainly, not exhaustive. However, we hope that the overall work will provide guidance for newcomers to this field and some hints to interested researchers for more detailed investigation of the present and future development of this hot and rapidly growing field.

Tunable Raman Gain in Transparent Nanostructured Glass-Ceramic Based on Ba2NaNb5O15 †.

Stimulated Raman scattering in transparent glass-ceramics (TGCs) based on bulk nucleating phase Ba2NaNb5O15 were investigated with the aim to explore the influence of micro- and nanoscale structural transformations on Raman gain. Nanostructured TGCs were synthesized, starting with 8BaO·15Na2O·27Nb2O5·50SiO2 (BaNaNS) glass, by proper nucleation and crystallization heat treatments. TGCs are composed of nanocrystals that are 10-15 nm in size, uniformly distributed in the residual glass matrix, with a crystallinity degree ranging from 30 up to 50% for samples subjected to different heat treatments. A significant Raman gain improvement for both BaNaNS glass and TGCs with respect to SiO2 glass is demonstrated, which can be clearly related to the nanostructuring process. These findings show that the nonlinear optical functionalities of TGC materials can be modulated by controlling the structural transformations at the nanoscale rather than microscale.

Critically coupled silicon Fabry-Perot photodetectors based on the internal photoemission effect at 1550 nm.

In this paper, design, fabrication and characterization of an all-silicon photodetector (PD) at 1550 nm, have been reported. Our device is a surface-illuminated PD constituted by a Fabry-Perot microcavity incorporating a Cu/p-Si Schottky diode. Its absorption mechanism, based on the internal photoemission effect (IPE), has been enhanced by critical coupling condition. Our experimental findings prove a peak responsivity of 0.063 mA/W, which is the highest value obtained in a surface-illuminated IPE-based Si PD around 1550 nm. Finally, device capacitance measurements have been carried out demonstrating a capacitance < 5 pF which has the potential for GHz operation subject to a reduction of the series resistance of the ohmic contact.

Noises investigations and image denoising in femtosecond stimulated Raman scattering microscopy.

In the literature of SRS microscopy, the hardware characterization usually remains separate from the image processing. In this article, we consider both these aspects and statistical properties analysis of image noise, which plays the vital role of joining links between them. Firstly, we perform hardware characterization by systematic measurements of noise sources, demonstrating that our in-house built microscope is shot noise limited. Secondly, we analyze the statistical properties of the overall image noise, and we prove that the noise distribution can be dependent on image direction, whose origin is the use of a lock-in time constant longer than pixel dwell time. Finally, we compare the performances of two widespread general algorithms, that is, singular value decomposition and discrete wavelet transform, with a method, that is, singular spectrum analysis (SSA), which has been adapted for stimulated Raman scattering images. In order to validate our algorithms, in our investigations lipids droplets have been used and we demonstrate that the adapted SSA method provides an improvement in image denoising.

Near-infrared sub-bandgap all-silicon photodetectors: state of the art and perspectives.

Due to recent breakthroughs, silicon photonics is now the most active discipline within the field of integrated optics and, at the same time, a present reality with commercial products available on the market. Silicon photodiodes are excellent detectors at visible wavelengths, but the development of high-performance photodetectors on silicon CMOS platforms at wavelengths of interest for telecommunications has remained an imperative but unaccomplished task so far. In recent years, however, a number of near-infrared all-silicon photodetectors have been proposed and demonstrated for optical interconnect and power-monitoring applications. In this paper, a review of the state of the art is presented. Devices based on mid-bandgap absorption, surface-state absorption, internal photoemission absorption and two-photon absorption are reported, their working principles elucidated and their performance discussed and compared.

Fiber Raman Amplifiers and Fiber Raman Lasers.

Stimulated Raman scattering (SRS) is a nonlinear optical effect, observed for the first time in 1962, which lies at the heart of fiber Raman amplifiers and fiber Raman lasers [...].

Micro and Nano Raman Lasers.

Raman lasers (RLs) are a class of optically pumped laser, offering coherent lights at any desired wavelength by a proper choice of the pump wavelength, when both wavelengths are within the transparency region of the gain material and an adequately high nonlinearity and/or optical intensity are provided [...].

Editorial for the Special Issue on Nonlinear Photonics Devices.

There is some incertitude on the creation of the term "photonics" and some ambiguity about its frontiers (and differences with respect to optoelectronics and electro-optics) [...].

Integrated Raman Laser: A Review of the Last Two Decades.

Important accomplishments concerning an integrated laser source based on stimulated Raman scattering (SRS) have been achieved in the last two decades in the fields of photonics, microphotonics and nanophotonics. In 2005, the first integrated silicon laser based upon SRS was realized in the nonlinear waveguide. This breakthrough promoted an intense research activity addressed to the realization of integrated Raman sources in photonics microstructures, like microcavities and photonics crystals. In 2012, a giant Raman gain in silicon nanocrystals was measured for the first time. Starting from this impressive result, some promising devices have recently been realized combining nanocrystals and microphotonics structures. Of course, the development of integrated Raman sources has been influenced by the trend of photonics towards the nano-world, which started from the nonlinear waveguide, going through microphotonics structures, and finally coming to nanophotonics. Therefore, in this review, the challenges, achievements and perspectives of an integrated laser source based on SRS in the last two decades are reviewed, side by side with the trend towards nanophotonics. The reported results point out promising perspectives for integrated micro- and/or nano-Raman lasers.

Fiber Amplifiers and Fiber Lasers Based on Stimulated Raman Scattering: A Review.

Nowadays, in fiber optic communications the growing demand in terms of transmission capacity has been fulfilling the entire spectral band of the erbium-doped fiber amplifiers (EDFAs). This dramatic increase in bandwidth rules out the use of EDFAs, leaving fiber Raman amplifiers (FRAs) as the key devices for future amplification requirements. On the other hand, in the field of high-power fiber lasers, a very attractive option is provided by fiber Raman lasers (FRLs), due to their high output power, high efficiency and broad gain bandwidth, covering almost the entire near-infrared region. This paper reviews the challenges, achievements and perspectives of both fiber Raman amplifier and fiber Raman laser. They are enabling technologies for implementation of high-capacity optical communication systems and for the realization of high power fiber lasers, respectively.

Implementation of a Nonlinear Microscope Based on Stimulated Raman Scattering.

Stimulated Raman scattering (SRS) microscopy uses near-infrared excitation light; therefore, it shares many multi-photon microscopic imaging properties. SRS imaging modality can be obtained using commercial laser-scanning microscopes by equipping with a non-descanned forward detector with proper bandpass filters and lock-in amplifier (LIA) detection scheme. A schematic layout of a typical SRS microscope includes the following: two pulsed laser beams, (i.e., the pump and probe directed in a scanning microscope), which must be overlapped in both space and time at the image plane, then focused by a microscope objective into the sample through two scanning mirrors (SMs), which raster the focal spot across an x-y plane. After interaction with the sample, transmitted output pulses are collected by an upper objective and measured by a forward detection system inserted in an inverted microscope. Pump pulses are removed by a stack of optical filters, whereas the probe pulses that are the result of the SRS process occurring in the focal volume of the specimen are measured by a photodiode (PD). The readout of the PD is demodulated by the LIA to extract the modulation depth. A two-dimensional (2D) image is obtained by synchronizing the forward detection unit with the microscope scanning unit. In this paper, the implementation of an SRS microscope is described and successfully demonstrated, as well as the reporting of label-free images of polystyrene beads with diameters of 3 µm. It is worth noting that SRS microscopes are not commercially available, so in order to take advantage of these characteristics, the homemade construction is the only option. Since SRS microscopy is becoming popular in many fields, it is believed that this careful description of the SRS microscope implementation can be very useful for the scientific community.

Three-dimensional label-free imaging throughout adipocyte differentiation by stimulated Raman microscopy.

Lipid droplets are lipid-storage organelles with a key role in lipid accumulation pathologies such as diabetes, obesity and atherosclerosis. Despite their important functions many aspects of lipid droplets biology are still unknown. This is partially due to the current use of exogenous labels to monitor their formation and remodelling by invasive imaging methods. Here, we apply stimulated Raman scattering microscopy to acquire images with high spatial resolution along with resolving capabilities of lipids and proteins and three-dimensional sectioning. Our images and data analysis demonstrate an increase in the number of large (>15µm2) lipid droplets in human adipocyte cells during differentiation process. In addition, spatially-resolved maps of lipids and proteins inside cells and three dimensional reconstructions of lipids at the initial and final steps of adipocyte differentiation are reported, too.

Subcellular chemical and morphological analysis by stimulated Raman scattering microscopy and image analysis techniques.

The visualization of heterogeneous morphology, segmentation and quantification of image features is a crucial point for nonlinear optics microscopy applications, spanning from imaging of living cells or tissues to biomedical diagnostic. In this paper, a methodology combining stimulated Raman scattering microscopy and image analysis technique is presented. The basic idea is to join the potential of vibrational contrast of stimulated Raman scattering and the strength of imaging analysis technique in order to delineate subcellular morphology with chemical specificity. Validation tests on label free imaging of polystyrene-beads and of adipocyte cells are reported and discussed.

Label-free imaging and biochemical characterization of bovine sperm cells.

A full label-free morphological and biochemical characterization is desirable to select spermatozoa during preparation for artificial insemination. In order to study these fundamental parameters, we take advantage of two attractive techniques: digital holography (DH) and Raman spectroscopy (RS). DH presents new opportunities for studying morphological aspect of cells and tissues non-invasively, quantitatively and without the need for staining or tagging, while RS is a very specific technique allowing the biochemical analysis of cellular components with a spatial resolution in the sub-micrometer range. In this paper, morphological and biochemical bovine sperm cell alterations were studied using these techniques. In addition, a complementary DH and RS study was performed to identify X- and Y-chromosome-bearing sperm cells. We demonstrate that the two techniques together are a powerful and highly efficient tool elucidating some important criterions for sperm morphological selection and sex-identification, overcoming many of the limitations associated with existing protocols.

Giant Raman gain in silicon nanocrystals.

Nanostructured silicon has generated a lot of interest in the past decades as a key material for silicon-based photonics. The low absorption coefficient makes silicon nanocrystals attractive as an active medium in waveguide structures, and their third-order nonlinear optical properties are crucial for the development of next generation nonlinear photonic devices. Here we report the first observation of stimulated Raman scattering in silicon nanocrystals embedded in a silica matrix under non-resonant excitation at infrared wavelengths (~1.5 µm). Raman gain is directly measured as a function of the silicon content. A giant Raman gain from the silicon nanocrystals is obtained that is up to four orders of magnitude greater than in crystalline silicon. These results demonstrate the first Raman amplifier based on silicon nanocrystals in a silica matrix, thus opening new perspectives for the realization of more efficient Raman lasers with ultra-small sizes, which would increase the synergy between electronic and photonic devices.