Biosorption of 2,4,6-trichlorophenol from Aqueous Medium Using Agro-waste: Pine (Pinus densiflora Sieb) Bark Powder.

Most industrial waste discharges are often contaminated with phenolic compounds, which constitute a major source of water pollution owing to their toxicity and low biodegradability. Development of cost-effective treatment of such industrial wastewater is therefore of paramount importance. Towards this end, we explore the efficacy of Pine bark powder (PBP), which is an agricultural solid waste material, as a low-cost biosorbent without any pre-treatment, for the adsorptive removal of 2,4,6-trichlorophenol (2,4,6-TCP) from aqueous media. The PBP was thoroughly characterized and the effect of important adsorption parameters were examined in the present investigation. The batch equilibrium data were analyzed using well-known isotherm models. Freundlich isotherm model provided the best description of the equilibrium biosorption behavior. At 25 ± 1 °C, the maximum biosorption capacity (qmax) was 289.09 mg/g, which is higher than most biosorbents reported in the literature while the removal as high as 97% was obtained. Moreover, the biosorption process was fast, attaining equilibrium in less than 120 min of contact. The Elovich model accurately described the kinetics data. In view of high biosorption capacity and.

Selective Oxidation of Cyclohexene over the Mesoporous H-Beta Zeolite on Copper/Nickel Bimetal Catalyst in Continuous Reactor.

The copper/nickel-metal on commercial H-Beta zeolite supports was synthesized with different wt % (Ni) of 5, 10, 15, and 20, and was used in the cyclohexene epoxidation process. The synthesized catalyst has been used in a continuous reactor for the cyclohexene epoxidation process, with mild conditions and H2O2 as an oxidant. The catalytic performance was ascertained by adjusting parameters such as the temperature, pressure, WHSV, reaction time, and solvents. The catalytic performance showed the resulting yield in both cyclohexene conversion and selectivity was more than 98.5%. The catalyst's textural attributes, morphology, chemical composition, and stability were determined using FT-IR, XRD, BET, HR-SEM, and TPD. The most active catalyst among those that were synthesized was evaluated, and the reaction parameters were selected to optimize yield and conversion. The H-Beta/Cu/Ni (15%) catalyst has the best conversion (98.5%) and selectivity (100%) for cyclohexene among the catalysts examined. Cu and Ni(15%) metals were successfully added to the H-Beta zeolite, causing little damage to the crystalline structure and resulting in good reusability over five cycles, as well as little loss of catalytic selectivity. Acetonitrile was the solvent that provided the highest conversion and selectivity among the others. These findings show that H-Beta/Cu/Ni bimetallic catalysts have the potential to be effective epoxidation catalysts. Because of their outstanding conversion and selectivity, the continuous reaction technique used in this work makes them appropriate for industrial production-level applications.

Ni-Fe bimetallic catalysts with high dispersion supported by SBA-15 evaluated for the selective oxidation of benzyl alcohol to benzaldehyde.

A wetness impregnation method was used to impregnate the substrate with a substantial quantity of oleic acid together with a metal precursor, leading to significantly dispersed Ni-Fe bimetallic catalysts based on mesoporous SBA-15. Using a wide variety of characterization methods, such as XRD, BET, and TEM Analysis, the physiochemical properties of the catalyst were determined. The addition of the metal does not have any effect on the structural characteristics of the SBA-15 catalyst, as validated by transmission electron microscopy (TEM), which shows that the prepared SBA-15 supported catalyst has a hexagonal mesoporous structure. The catalytic capabilities of the Ni-Fe-SBA-15 catalysts were evaluated in the conversion of BzOH using tert-butyl hydroperoxide (TBHP) as an oxidant and acetonitrile as a solvent. The Ni/Fe-SBA-15 (NFS-15) catalytic composition is the best of the developed catalysts, with a maximum conversion of 98% and a selectivity of 99%. In-depth investigations were conducted into the molar ratio of TBHP to BzOH, the dosage of the catalyst, the reaction rate, temperature, and solvent. The recycling investigations indicate that the synthesized Ni/Fe-SBA-15 (NFS-15) catalyst seems to be more durable up to seven successive cycles.

Sustainable biofuel synthesis from non-edible oils: a mesoporous ZSM-5/Ni/Pt catalyst approach.

This work examines the hydrodeoxygenation (HDO) activity of non-edible oils using a high surface area catalyst. The HDO activity was thoroughly examined and contrasted using the high surface area catalyst Ni/Pt-ZSM-5 as well as other supports like MCM-48 and H-beta. Ni/Pt bimetals supported on mesoporous ZSM-5 were created via reverse order impregnation to facilitate HDO of non-edible oils. Techniques such as XRD, FT-IR, BET, HR-TEM, HR-SEM, TPD, and TGA were used to characterize the produced catalysts. The synthesized catalysts considerably influenced the hydrodeoxygenation activities for the synthesis of lengthy chain hydrocarbons in a stainless-steel reactor with a high-pressure fixed bed between 300 and 375 °C under 10-40 bar hydrogen pressure. High levels of Ni/Pt-ZSM-5 acidity, textural, and H2 consumption qualities were discovered. Distributions of the products were also reviewed, along with comparisons of the structure-activity connections.

Preparation, Characterization, and Chemically Modified Date Palm Fiber Waste Biomass for Enhanced Phenol Removal from an Aqueous Environment.

The date palm tree is extensively cultivated in Middle Eastern countries such as Saudi Arabia, generating a large amount of waste in the form of leaves, seeds, and fibrous materials. This study examined the feasibility of using raw date palm fiber (RDPF) and NaOH chemically modified date palm fiber (NaOH-CMDPF) obtained from discarded agricultural waste for the removal of phenol in an aqueous environment. The adsorbent characterization was performed by using different techniques, i.e., particle size analysis; elemental analyzer (CHN); and BET, FTIR, and FESEM-EDX analysis. The FTIR analysis revealed the presence of various functional groups on the surface of the RDPF and NaOH-CMDPF. The results showed that chemical modification by NaOH increased the phenol adsorption capacity that was well-fitted by the Langmuir isotherm. Higher removal was obtained with NaOH-CMDPF (86%) than with the RDPF (81%). The RDPF and NaOH-CMDPF sorbents' maximum (Qm) adsorption capacities were more than 45.62 mg/g and 89.67 mg/g and were comparable to the sorption capacities of various other types of agricultural waste biomass reported in the literature. The kinetic studies confirmed that the adsorption of phenol followed the pseudo-second-order kinetic process. The present study concluded that the RDPF and NaOH-CMDPF were eco-friendly and cost-effective in promoting sustainable management and the reuse of the Kingdom's lignocellulosic fiber waste material.

Cellulose graphitic carbon directed iron oxide interfaced polypyrrole electrode materials for high performance supercapacitors.

The rising demand for green and clean energy urges the enlargement of economical and proficient electrode materials for supercapacitors. Herein, we designed a novel electrode material by porous cellulose graphitic carbon (CC) derived from bio-waste cornhusk via the pyrolysis route, and α-Fe2O3 decorated nanostructure with CC (CCIO) was achieved in situ pyrolysis of corn-husk and Fe(NO3)3·9H2O metal salt followed by a coating of polypyrrole (CCIOP). The CC, CCIO, and CCIOP nanocomposite electrodes were characterized by XRD, Raman, FTIR, FE-SEM/EDX, FE-TEM, XPS, and BET analysis. The CCIOP nanocomposite electrode exhibits an enhanced specific capacitance (Csp) of 290.9 F/g, which is substantial to its pristine CC (128.3 F/g), PPy (140.3 F/g), and CCIO (190.7 F/g). The Csp of CCIOP in a three-electrode system, using 1 M Na2SO4 electrolyte exhibits excellent capacity retention of 79.1 % even at a high current density of 10 A/g. The as-fabricated asymmetric supercapacitor (ASC) delivered a remarkable capacity retention of 88.7 % with a coulombic efficiency of 98.8 % even after 3000 cycles. The study shows successful utilization of cellulose from bio-waste cornhusk into a substantial template applicable in future alternative energy storage devices.

Enhanced solar-driven photocatalytic performance of a ternary composite of SnO2 quantum dots//AgVO3 nanoribbons//g-C3N4 nanosheets (0D/1D/2D) structures for hydrogen production and dye degradation.

Herein, we report the synthesis of between SnO2 QDs /AgVO3 nanoribbons/g-C3N4 nanosheets of ternary photocatalytic systems for the production of H2 through light irradiation. The SnO2/AgVO3/g-C3N4 photocatalyst was successfully produced by using the hydrothermal process. The structural characterizations of the samples revealed the successful formation of ternary heterostructures where SnO2, AgVO3 and g-C3N4 (quantum dots/nanoribbons/nanosheets) 0D/1D/2D structures make a good interface with each other. The fabricated heterostructures of AgVO3/g-C3N4 and SnO2/AgVO3/g-C3N4 photocatalytic structures performed enriched photocatalytic performance for H2 production over that of the pristine g-C3N4, AgVO3 and SnO2 photocatalysts. The AgVO3/g-C3N4 and SnO2 /AgVO3/g-C3N4 of photocatalysts were found to produce H2 of around 17,000 µmol g-1 and 77,000 µmol g-1, respectively, which is much 4.5 times greater than that of AgVO3/g-C3N4 photocatalyst. Moreover, the photodegradation behaviours of prepared catalysts were studied with the dye (rhodamine B, RhB) under light irradiation. The ternary composite SnO2/AgVO3/g-C3N4 performed photodegradation of RhB in 50 min. The higher photocatalytic activity for the ternary photocatalysts is predominantly due to the effective charge separation at the perfect interface formation amid SnO2 and AgVO3/g-C3N4.

Strontium Aluminate-Based Long Afterglow PP Composites: Phosphorescence, Thermal, and Mechanical Characteristics.

A tremendous potential has been observed in the designing of long afterglow materials for sensing, bioimaging, and encryption applications. In this study, two different strontium aluminate-based luminescent materials; SrAl2O4: Eu, Dy (S1), and Sr4Al14O25: Eu, Dy (S2) were melt-mixed with polypropylene (PP) matrix, and the phosphorescence properties were evaluated. After excitation at 320 nm, the PP/S1 composite exhibited a green emission and the PP/S2 generated a blue emission at 520 nm and 495 nm, respectively. The emission spectra intensity increased by increasing the content of these luminescent fillers. The attenuated total reflection-Fourier transform infrared (ATR-FTIR) experiments show that no chemical reaction occurred during the melt-mixing process. The differential scanning calorimetry (DSC) results revealed that the total crystallinity of the composites reduced by increasing the amount of the fillers; however, no changes in the temperature of melting (Tm) and crystallization (Tc) of PP were observed. Both fillers improved the impact strength of the composites, but the tensile strength (TS) and modulus (TM) decreased. Poly (ethylene glycol) dimethyl ether (P) plasticizer was used to improve the filler-matrix interaction and its dispersion; nevertheless, it adversely affected the intensity of the luminescence emissions.

A brief review on solid lipid nanoparticles: part and parcel of contemporary drug delivery systems.

Drug delivery technology has a wide spectrum, which is continuously being upgraded at a stupendous speed. Different fabricated nanoparticles and drugs possessing low solubility and poor pharmacokinetic profiles are the two major substances extensively delivered to target sites. Among the colloidal carriers, nanolipid dispersions (liposomes, deformable liposomes, virosomes, ethosomes, and solid lipid nanoparticles) are ideal delivery systems with the advantages of biodegradation and nontoxicity. Among them, nano-structured lipid carriers and solid lipid nanoparticles (SLNs) are dominant, which can be modified to exhibit various advantages, compared to liposomes and polymeric nanoparticles. Nano-structured lipid carriers and SLNs are non-biotoxic since they are biodegradable. Besides, they are highly stable. Their (nano-structured lipid carriers and SLNs) morphology, structural characteristics, ingredients used for preparation, techniques for their production, and characterization using various methods are discussed in this review. Also, although nano-structured lipid carriers and SLNs are based on lipids and surfactants, the effect of these two matrixes to build excipients is also discussed together with their pharmacological significance with novel theranostic approaches, stability and storage.

Enhanced Supercapacitive Performance of Higher-Ordered 3D-Hierarchical Structures of Hydrothermally Obtained ZnCo2O4 for Energy Storage Devices.

The demand for eco-friendly renewable energy resources as energy storage and management devices is increased due to their high-power density and fast charge/discharge capacity. Recently, supercapacitors have fascinated due to their fast charge-discharge capability and high-power density along with safety. Herein, the authors present the synthesis of 3D-hierarchical peony-like ZnCo2O4 structures with 2D-nanoflakes by a hydrothermal method using polyvinylpyrrolidone. The reaction time was modified to obtain two samples (ZCO-6h and ZCO-12h) and the rest of the synthesis conditions were the same. The synthesized structures were systematically studied through various techniques: their crystalline characteristics were studied through XRD analysis, their morphologies were inspected through SEM and TEM, and the elemental distribution and oxidation states were studied by X-ray photoelectron spectroscopy (XPS). ZCO-12h sample has a larger surface area (55.40 m2·g-1) and pore size (24.69 nm) than ZCO-6h, enabling high-speed transport of ions and electrons. The ZCO-12h electrode showed a high-specific capacitance of 421.05 F·g-1 (31.52 C·g-1) at 1 A·g-1 and excellent cycle performance as measured by electrochemical analysis. Moreover, the morphologic characteristics of the prepared hierarchical materials contributed significantly to the improvement of specific capacitance. The excellent capacitive outcomes recommend the 3D-ZnCo2O4 hierarchical peony-like structures composed of 2D-nanoflakes as promising materials for supercapacitors with high-performance.

Silica-immobilized ionic liquid Brønsted acids as highly effective heterogeneous catalysts for the isomerization of n-heptane and n-octane.

Metal-free imidazolium-based ionic liquid (IL) Brønsted acids 1-methyl imidazolium hydrogen sulphate [HMIM]HSO4 and 1-methyl benzimidazolium hydrogen sulphate [HMBIM]HSO4 were synthesized. Their physicochemical properties were investigated using spectroscopic and thermal techniques, including UV-Vis, FT-IR, 1H NMR, 13C-NMR, mass spectrometry, and TGA. The ILs were immobilized on mesoporous silica gel and characterized by FT-IR spectroscopy, scanning electron microscopy, Brunauer-Emmett-Teller analysis, ammonia temperature-programmed desorption, and thermogravimetric analysis. [HMIM]HSO4@silica and [HMBIM]HSO4@silica have been successfully applied as promising replacements for conventional catalysts for alkane isomerization reactions at room temperature. Isomerization of n-heptane and n-octane was achieved with both catalysts. In addition to promoting the isomerization of n-heptane and n-octane (a quintessential reaction for petroleum refineries), these immobilized catalysts are non-hazardous and save energy.

Silver Quantum Dot Decorated 2D-SnO2 Nanoflakes for Photocatalytic Degradation of the Water Pollutant Rhodamine B.

Decoration of 2D semiconductor structures with heterogeneous metal quantum dots has attracted considerable attention due to advanced optical, electrical, and catalytic properties that result from the large surface-to-volume ratio associated with these structures. Herein, we report on silver quantum dot decorated 2D SnO2 nanoflakes for the photocatalytic abatement of water effluents, the synthesis of which was achieved through a straightforward and mild hydrothermal procedure. The photocatalysts were systematically investigated using UV-Vis, XRD, electron microscopy (SEM, HR-TEM), EDX, XPS and FTIR. The photocatalytic activity of the nanostructures was evaluated for the abatement of water pollutant rhodamine B (RhB), under light irradiation. The mild hydrothermal synthesis (100 °C) proved highly efficient for the production of large scale Ag quantum dot (QD)/SnO2 nanoflakes for a novel photocatalytic application. The decoration of SnO2 with Ag QDs significantly enhances the synergetic charge transfer, which diminishes the photo-induced electron-hole reunion. Moreover, the plasmonic effect from Ag QDs and 2D-SnO2 structures acts as an electron tank to collect the photo-induced electrons, generating a Schottky barrier between the SnO2 structures and quantum dots. Overall, this resulted in a facile and efficient degradation of RhB, with a rate double that of pristine SnO2.