Towards "Green" ANFO: Study of Perchlorates and Inorganic Peroxides as Potential Additives.

Ammonium nitrate-fuel oil (ANFO) explosives are inexpensive and readily produced, but are highly prone to misfires, with the remaining explosive being a significant risk and environmental contaminant. In this work, studies on various additives, such as selected perchlorates and inorganic peroxides, which are intended to lower the susceptibility of ANFO to misfires by increasing its sensitivity to shock, have been conducted. These studies showed the viability of using these additives in ANFO, allowing for conducting shock wave sensitivity tests for bulk charges in the future. We investigated the effects of introducing these additives into ANFO (on its sensitivity), as well as thermal and energetic properties. We observed minor increases in friction and impact sensitivity, as well as a moderate reduction in the decomposition temperature of the additive-supplemented ANFO in comparison to unmodified ANFO.

Applying Nanofiltration to Decrease Energy Consumption and Sensitivity toward Feed Composition Fluctuations in Salt Production.

The only currently active industrial-scale plant that uses coal mine brines, located in Czerwionka-Leszczyny, uses ZOD (Zaklad Odsalania Debiensko, the name of the plant's former owner) technology, based on mechanical vapor compression evaporators. The plant produces evaporated salt that meets the specifications for edible salt; however, the technology is highly energy-consuming. The presented work focuses on the modeling of ZOD technology if applied to the water treatment of the 'Ziemowit-650' coal mine. Using the results of bench-scale investigation of brine nanofiltration and a mathematical model of ZOD technology based on Czerwionka-Leszczyny performance, the energy consumption per ton of produced salt was estimated for two cases: (1) ZOD technology treating the 'Ziemowit-650' brine and (2) ZOD technology treating the permeate of nanofiltration (NF) working on the 'Ziemowit-650' brine. The sensitivity of the system was investigated in the range of -10% to + 10% of Cl-, SO42-, Mg2+, and Ca2+ concentration, assuming that the sodium concentration also changes to meet the electroneutrality requirement. The results show that nanofiltration pretreatment not only decreases energy consumption but it also makes salt production less sensitive to fluctuations in feed water composition.

Investigation of Combustion of KMnO4/Zn Pyrotechnic Delay Composition.

This article reports an investigation of the combustion of a binary pyrotechnic delay composition (PDC), consisting of zinc powder as fuel and KMnO4 as an oxidising agent, with zinc content ranging from 35 to 70 wt. %. The linear burning rate for delay compositions in the form of pyrotechnic fuses was investigated. Compositions with zinc content between 50 and 70 wt. % yielded burn rates in the range of 13.30-28.05 mm/s. The delay compositions were also tested for their sensitivity to friction and impact, where the compositions showed impact sensitivity in the range from 7.5 to 50 J and were insensitive to friction. Tests in a pressure bomb were carried out to determine the maximum overpressure and pressurisation rate. The thermal properties of the composition were evaluated by thermogravimetric analysis (DTA/TG). The morphology of the combustion products was studied by SEM technique, EDS analyses were used to investigate the element distribution of the post-combustion residues, providing an insight into the phenomena taking place during the combustion of the delay compositions.

Improving the Performance of a Salt Production Plant by Using Nanofiltration as a Pretreatment.

The Debiensko plant in Czerwionka-Leszczyny, Poland, producing evaporated salt from the saline mine water, faces increasing operating costs due to its high energy consumption. To improve the performance of the plant, a two-pass nanofiltration with intermediate crystallization of gypsum was proposed as a pretreatment. Based on the results of pilot-scale research, it was found that the removal of most of the calcium, magnesium, and sulfate allows a substantial reduction in the concentration of these components in the concentrated brine, which is then directed to a sodium chloride crystallization evaporator. This makes it possible to increase salt yield from the current 58.8% to 76.1% and indirectly reduce energy consumption from 1350 kWh/t to 1068 kWh/t. At the same time, the volume of the highly saline post-crystallization lyes is decreased by 66%, and a new stream is obtained: a Mg-rich solution, which could be used for magnesium hydroxide recovery.

Nano-Silica Carriers Coated by Chloramphenicol: Synthesis, Characterization, and Grinding Trial as a Way to Improve the Release Profile.

Silica nanoparticles were applied as the carrier of chloramphenicol (2,2-dichloro-N-[(1R,2R)-1,3-dihydroxy-1-(4-nitrophenyl)propan-2-yl]acetamide), and were loaded in a 1% carbopol-based gel (poly(acrylic acid)), which allowed obtainment of an upgraded drug form. The samples of silica materials were obtained by means of modified Stöber synthesis, and their morphological properties were analyzed using Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) method, elemental analysis (EA), thermogravimetric analysis (TGA), analysis of the specific surface properties, X-ray diffraction study (XRD), scanning electron microscope (SEM), and dynamic light scattering (DLS) methods, which permitted the selection of the drug carrier. The two obtained silica carriers were coated with chloramphenicol and loaded into 1% carbopol gel. The release studies were then performed. The release results were evaluated using mathematical models as well as model-independent analysis. It was found that the modification of the synthesis of the silica by the sol-gel method to form a product coated with chloramphenicol and further grinding of the silica material influenced the release of the active substance, thus allowing the modification of its pharmaceutical availability. The change in the parameters of silica synthesis influenced the structure and morphological properties of the obtained silica carrier. The grinding process determined the way of adsorption of the active substance on its surface. The studies showed that the proper choice of silica carrier has a considerable effect on the release profile of the prepared hydrogel formulations.