The Effect of Sodium Bentonite in the Thermo-Catalytic Reduction of Viscosity of Heavy Oils.

To study the synergistic catalysis of an ex situ catalyst and in situ clay in the aquathermolysis of heavy oil, in this paper, a series of bentonite-supported catechol-metal complexes were prepared, and the catalytic viscosity reduction performance in the aquathermolysis of heavy oil was investigated. Under the optimized conditions, the viscosity can be reduced by 73%, and the pour point can be lowered by 15.0 °C at most, showing the synergistic catalysis of the ex situ catalyst and in situ clay in this aquathermolytic reaction. Thermogravimetry, physical adsorption-desorption, and scanning electron microscopy were conducted to characterize the thermal stability and microstructure of the ex situ catalyst. The components of the heavy oil before and after the reaction were fully characterized. Six model compounds were used to simulate the aquathermolysis reaction process. In order to study the mechanism of viscosity reduction after the catalytic aquathermolysis reaction, the compounds were analyzed by GC-MS. It is believed that these results will be beneficial in the future for related research in this field.

[Mycobacterium marinum as a cause of human and animal infections].

Mycobacterium marinum is a slowly growing non-tuberculous (environmental, atypical) mycobacterium with zoonotic potential. It occurs in the aquatic environment and causes diseases in fish and other aquatic animals known as mycobacterioses. In humans, it primarily causes skin infections, which are most commonly located in the upper limbs. The disease commonly appears in connection with the aquarium environment and is thus referred to as fish tank granuloma. As with all mycobacterial diseases, treatment is complicated and lengthy. For a definitive determination of the pathogen, biological materials should always be examined in a laboratory specializing in diagnosing mycobacteria. Critical for the right diagnosis is proper sample collection and assessment of the patient's history. To detect mycobacteria, culture and microscopy are generally used. Species are identified using modern biological methods such as mass spectrometry (MALDI), polymerase chain reaction, hybridization probes or sequencing.

Comparison of methods for the isolation of mycobacteria from water treatment plant sludge.

Nontuberculous mycobacteria (NTM) are ubiquitous organisms in all natural ecosystems, including water environments. Several of these species are potential pathogens which affect human health. NTM most commonly cause pulmonary, skin or soft tissue infections. Primary sludge obtained from the water treatment plants of four drinking water reservoirs were subjected to analysis for mycobacteria. Five decontamination methods (5% oxalic acid, modified Petroff, HCl-NaOH, N-acetyl-L-cysteine-sodium hydroxide and 0.05% cetylpyridinium chloride), three growth media (Herrold's egg yolk medium with and without the antibiotic cocktail PANTA and Löwenstein-Jensen medium with sodium pyruvate) and three incubation temperatures (25, 30 and 37 °C) for isolation of mycobacteria were compared in the analysis of 18 sludge samples. To evaluate examined methods, the overall positive, negative, and contamination rate, and these rates in respect to localities are taken into account. Statistical analysis demonstrated that the best combination for the recovery of mycobacteria with the minimum number of contaminating microorganisms is 5% oxalic acid decontamination cultured on Herrold's egg yolk medium with the antibiotic cocktail PANTA at 25 °C. The least suitable is N-acetyl-L-cysteine-sodium hydroxide decontamination cultured on Löwenstein-Jensen medium with sodium pyruvate at 25 °C. From 18 sludge samples we isolated 27 mycobacterial species or groups; Mycobacterium algericum, M. arabiense, M. heraklionense, M. minnesotense, M. moriokaense, M. salmoniphilum and M. vulneris were isolated from the natural water environment for the first time. Because the natural water environment is the main source of potentially pathogenic mycobacteria for humans, it is important to direct particular focus to newly described mycobacterial species.

Microbial quality and molecular identification of cultivable microorganisms isolated from an urban drinking water distribution system (Limassol, Cyprus).

Microorganisms can survive and multiply in aged urban drinking water distribution systems, leading to potential health risks. The objective of this work was to investigate the microbial quality of tap water and molecularly identify its predominant cultivable microorganisms. Tap water samples collected from 24 different households scattered in the urban area of Limassol, Cyprus, were microbiologically tested following standard protocols for coliforms, E. coli, Pseudomonas spp., Enterococcus spp., and total viable count at 22 and 37 °C. Molecular identification was performed on isolated predominant single colonies using 16SrRNA sequencing. Approximately 85% of the household water samples were contaminated with one or more microorganisms belonging to the genera of Pseudomonas, Corynebacterium, Agrobacterium, Staphylococcus, Bacillus, Delftia, Acinetobacter, Enterococcus, Enterobacter, and Aeromonas. However, all samples tested were free from E. coli. This is the first report in Cyprus molecularly confirming specific genera of relevant microbial communities in tap water.

The water environment as a source of potentially pathogenic mycobacteria.

Nontuberculous mycobacteria (NTM) are ubiquitous organisms of a wide variety of environmental reservoirs, including natural and municipal water, soil, aerosols, protozoans, animals and humans. Several of these species are potential pathogens which affect human health. The aim of this study was to determine the occurrence of NTM in the water environment. Samples were taken from 13 water-related facilities including fish ponds, storage ponds, drinking water reservoirs and an experimental recirculation system. Altogether, 396 samples of water, sediment and aquatic plants were collected and analysed. All samples were examined using conventional culture methods. Suspected microbial isolates were subjected to polymerase chain reaction analysis and identified using partial sequence analysis of the 16S rDNA gene. The culture revealed 94/396 samples (23.7%) that contained mycobacteria. Among known NTM we identified potentially pathogenic mycobacteria isolated from the fresh water environment for the first time: Mycobacterium asiaticum, M. chimaera, M. interjectum, M. kumamotonense, M. lentiflavum, M. montefiorense, M. nebraskense, M. paraffinicum and M. simiae. Epidemiologic studies suggest that the natural water environment is the principal source of human exposure. Our results indicate that besides the well-known potentially pathogenic mycobacteria it is important to observe occurrence, proliferation and persistence of newly discovered mycobacterial species.

The tracing of mycobacteria in drinking water supply systems by culture, conventional, and real time PCRs.

Mycobacteria are widely present in diverse aquatic habitats, where they can survive for months or years while some species can even proliferate. The resistance of different mycobacterial species to disinfection methods like chlorination or ozonation could result in their presence in the final tap water of consumers. In this study, the culture method, Mycobacterium tuberculosis complex conventional duplex PCR for detection of non-tuberculous mycobacteria (NTM) and quantitative real-time PCR (qPCR) to detect three subspecies of M. avium species (M. a. avium, M. a. hominissuis, and M. a. paratuberculosis) were used to trace their possible path of transmission from the watershed through the reservoir and drinking water plant to raw drinking water and finally to households. A total of 124 samples from four drinking water supply systems in the Czech Republic, 52 dam sediments, 34 water treatment plant sludge samples, and 38 tap water household sediments, were analyzed. NTM of 11 different species were isolated by culture from 42 (33.9 %) samples; the most prevalent were M. gordonae (16.7 %), M. triplex (14.3 %), M. lentiflavum (9.5 %), M. a. avium (7.1 %), M. montefiorenase (7.1 %), and M. nonchromogenicum (7.1 %). NTM DNA was detected in 92 (76.7 %) samples. By qPCR analysis a statistically significant decrease (P < 0.01) was observed along the route from the reservoir (dam sediments), through water treatment sludge and finally to household sediments. The concentrations ranged from 10(0) to 10(4) DNA cells/g. It was confirmed that drinking water supply systems (watershed-reservoir-drinking water treatment plant-household) might be a potential transmission route for mycobacteria.

Nontuberculous mycobacteria in freshwater fish and fish products intended for human consumption.

Nontuberculous mycobacteria (NTM) are potentially pathogenic agents commonly found in natural ecosystems, while food is considered to be another source of NTM for humans. We investigated a total of 92 tissue samples of freshwater fish and fish products: fish directly obtained from ponds (n=25), retail fresh (n=23) and frozen fish (n=23) and smoked fish products (n=21). Culture examination for the presence of mycobacteria was positive in 11 (11.9%) from all the examined samples. The 15 obtained isolates were identified as Mycobacterium fortuitum (n=5), M. immunogenum (n=2), M. phocaicum/ mucogenicum (n=1), M. neoaurum (n=2), M. peregrinum (n=2), M. porcinum (n=1) and M. senegalense/houstonense/conceptionense (n=2). NTM DNA was found in one (4.0%) sample of fresh fish from ponds and in 60.9% and 91.3% of retail fresh and frozen fish, respectively. None of the smoked fish products contained NTM DNA. The results of our study suggest that freshwater fish and fish products, especially retail frozen fish, might be a reservoir of NTM for humans, and proper handling and treatment before consumption of such products is recommended.

Use of Highly Dispersed Mixed Metal Hydroxide Gel Compared to Bentonite Based Gel for Application in Drilling Fluid under Ultra-High Temperatures.

In order to solve the problem of poor dispersion and stability of mixed metal hydroxide (MMH), a kind of mixed metal hydroxide-like compound (MMHlc) gel was synthesized for use as the base mud in drilling fluid instead of bentonite gel. Na2CO3, Na2SiO3, and C17H33CO2Na were used as precipitants to form MMHlc with larger interlayer spacing and smaller particle size. MMHlc was synthesized by the coprecipitation method at 25 °C with a metal molar ratio of Mg:Al:Fe = 3:1:1. The performance evaluation of the treated drilling fluid showed that MMHlc (S2) synthesized using Na2SiO3 as the precipitant had the characteristics of low viscosity, low filtration, and a high dynamic plastic ratio at 25 °C, which fully met the requirements of oil field application, and it maintained its excellent properties after being aged at 250 °C for 16 h. Linear expansion and rolling recovery experiments showed that the S2 sample had excellent rheological properties and good inhibition. X-ray diffraction and FT-IR experiments showed that S2 had the most complete crystal structure, its interlayer distance was large, and its ion exchange capacity was strong. The thermogravimetric experiment showed that the S2 crystal was stable and the temperature resistance of the crystal could reach 340 °C. Zeta potential, particle size analysis, SEM, and TEM results showed that S2 is a nanomaterial with a complete morphology and uniform distribution. The drilling fluid of this formula had the characteristics of low viscosity, low filtration loss, and a high dynamic plastic ratio, and it met the conditions for oil field application. Considering these results, the new MMH prepared by our research institute is a drilling fluid material that can be used at ultra-high temperatures and can provide important support for drilling ultra-deep wells.

Remediation of pesticides contaminated water using biowastes-derived carbon rich biochar.

The competition impact and feedstock type on the removal of water pesticides using biochar have not yet been sufficiently investigated. Therefore, here we investigated the potentiality of three different biochars (BCs) derived from rice husk (RHB), date pit (DPB), and sugarcane bagasse (SBB) biowastes for the simultaneous removal of ten pesticides from water in a competitive adsorption system. The BCs structural characterization and morphology were investigated by XRD, FTIR spectroscopy and SEM analysis. The potential adsorption mechanisms have been investigated using various isothermal and kinetic models. RHB showed the highest removal percentages (61% for atrazine/dimethoate and 97.6% for diuron/chlorfenvinphos) followed by DPB (56% for atrazine/dimethoate and 95.4% for diuron/chlorpyrifos) and then SBB (60.8% for atrazine/dimethoate and 90.8% for chlorpyrifos/malathion). The higher adsorption capacity of RHB and DPB than SBB can be due to their high total pore volume and specific surface area (SSA). Langmuir model described well the sorption data (R2 = 0.99). Adsorption equilibrium was achieved after 60 min for RHB, and 120 min for both DPB and SBB. The optimum adsorbent dose (g/L) was 10 for RHB and 4 for DPB and SBB. The removal efficiency of pesticides was enhanced by decreasing pH from 9 to 5 by RHB and to 3 by DPB and SBB. XRD and FTIR spectroscopy confirmed that BCs contain some active adsorption groups and metal oxides such as MgO, SiO, Al2O3, CaO, and TiO2 that can play an effective role in the pesticides sorption. BET-N2 adsorption analysis demonstrated that the BC pore size contributes significantly to pesticide adsorption. These findings indicate that RHB, DPB, and SBB have ability for adsorption of water pesticides even under acidic conditions. Therefore, the rice husk, date pit, and sugarcane bagasse biowastes could be pyrolyzed and reused as effective and low-cost sorbents for elimination of hazardous substances such as pesticides in the aqueous environments.

Mycobacterium marinum infections in humans and tracing of its possible environmental sources.

The low frequency of nontuberculous mycobacterial infections, nonspecific symptoms for individual mycobacteria, and the lack of specific identification methods could alter correct diagnosis. This study presents a combined microbiology and molecular-based approach for Mycobacterium marinum detection in four aquarists with cutaneous mycobacterial infection. Simultaneously, ecology screening for M. marinum presence in the aquarists' fish tanks was performed. A total of 38 mycobacterial isolates originated from four human patients (n = 20), aquarium animals (n = 8), and an aquarium environment (n = 10). Isolate identification was carried out using 16S rRNA sequence analysis. A microbiology-based approach, followed by 16S rRNA sequence analysis, was successfully used for detection of M. marinum in all four patients. Animal and environmental samples were simultaneously examined, and a total of seven mycobacterial species were isolated: Mycobacterium chelonae , Mycobacterium fortuitum , Mycobacterium gordonae , Mycobacterium kansasii , Mycobacterium mantenii , Mycobacterium marinum , and Mycobacterium peregrinum . The presence of M. marinum was proven in the aquarium environments of two patients. Although M. marinum is described as being present in water, it was detected only in fish.

Use of Betaine-Based Gel and Its Potential Application in Enhanced Oil Recovery.

In this paper, a betaine-based gel containing 2.0% erucamide propyl betaine (EAPB), 0.5% oleic acid amide propyl betaine (OAPB), and 0.1% KCl was prepared for use as a fracturing fluid. The performance evaluation showed that KCl may improve the temperature resistance and increase the viscosity of the optimized fracturing fluid. At 80 °C, the apparent viscosity of the viscoelastic surfactant (VES)-based fracturing fluid was approximately 50 mPa·s. Furthermore, the gel had high shear resistance, good viscosity stability, and high sand-carrying performance. After being sheared at 170 s−1 for 60 min, the reduction in viscosity was 13.6%. The viscosity of the gel was relatively stable at room temperature (27 °C) for one week. In a suspension containing 10% sand (particle size < 0.45 mm, density = 2.75 g cm−3), the settling velocity of proppant particles was 1.15 cm h−1. In addition, we detected that the critical micelle concentration of this gel was approximately 0.042 wt%. The viscosity could be reduced to <5 mPa·s at 60 °C within 1 h when 6.0% crude oil was present, and oil displacement experiments showed that the broken fracturing fluid can enhance the oil displacement rate up to 14.5%. This work may facilitate research on fracturing fluids and oil recovery.

Lubricity and Rheological Properties of Highly Dispersed Graphite in Clay-Water-Based Drilling Fluids.

Improving the tribological characteristics of water-based drilling fluids by adding graphene-based lubricants has garnered attention because of the potential for a range of inorganic-material-based additives at high temperature. In this study, we constructed a green and simple adsorption approach to prepare highly dispersed graphite using a cationic surfactant for graphite modification. The findings demonstrated that the prepared graphite was highly dispersed in water and had a low sedimentation rate and small contact angle in distilled water. The concentration dosage of cetyltrimethylammonium chloride (CTAC) on graphite was 0.02 g/g. We evaluated the performance of the modified graphite as a lubricated additive in water-based drilling through a rheological study and viscosity coefficient measurement. The results showed that the viscosity coefficient of drilling fluid with 0.05% modified graphite was reduced by 67% at 180 °C. We proved that the modified graphite can significantly improve the lubrication performance of drilling fluid. Furthermore, we revealed the lubrication mechanism by analyzing the chemical structural and crystalline and morphological features of graphite through a particle size test, zeta potential test, Fourier transform infrared (FTIR) spectroscopy, X-ray powder diffraction (XRD), and scanning electron microscopy (SEM) measurements. The results indicated that the modification of graphite by CTAC only occurs through physical adsorption, without changing the crystal structure. These findings provide a reference for the development of high-performance water-based drilling fluids.

Ecotoxicological effects of per- and polyfluoroalkyl substances (PFAS) and of a new PFAS adsorbing organoclay to immobilize PFAS in soils on earthworms and plants.

A novel adsorptive organoclay (Intraplex A®) was developed for the in situ immobilization of per- and polyfluoroalkyl substances (PFAS) in the vadose zone. We provide the first evaluation of the effects of Intraplex A® on earthworms and plants in a PFAS-contaminated soil. Ecotoxicological tests were carried out on control soil with and without Intraplex A® (C + I and C, respectively) and PFAS-contaminated soil with and without Intraplex A® (PFAS + I and PFAS, respectively). We investigated the acute ecotoxicological effects of PFAS and Intraplex A® on the growth, reproduction and survival of earthworms (Eisenia fetida) and on plant growth (oat - Avena sativa and turnip - Brassica rapa L. silvestris). Earthworm lethality was 7.6 lower in PFAS + I than in PFAS soil. Earthworms avoided 100% C + I and PFAS + I soils, and reduced earthworms' reproduction was observed in both these soils. For both plant species, the PFAS + I soil yielded less fresh and dry shoot biomass than the PFAS soil, while root growth remained unaffected (all tests: p < 0.05). Soils with Intraplex A® had some negative effects on plants and earthworms, which must be balanced with its benefits as an in situ PFAS adsorbent.

Rice hull biochar enhances the mobilization and methylation of mercury in a soil under changing redox conditions: Implication for Hg risks management in paddy fields.

Biochar amendment to paddy soils was promising to mitigate mercury (Hg) accumulation in rice; thus, it was applied to reduce human Hg exposure via rice consumption. However, how biochar affects Hg mobilization and MeHg formation in soil under changed redox potential (Eh) conditions remained unknown. Here, we explored the change of dissolved total Hg (DTHg) and dissolved MeHg (DMeHg), and their controlling biogeochemical factors in a soil with(out) biochar amendment under changing Eh conditions using biogeochemical microcosm. Biochar amendment resulted in a widen Eh range (-300 to 400 mV) compared to the control (-250 to 350 mV), demonstrating that biochar promoted reduction-oxidization reactions in soil. Biochar amendment enhanced Hg mobilization by mediating reductive dissolution of Fe/Mn (hydr)oxides. Thus, the increased Hg availability promoted MeHg formation in the soils. Biochar amendment changed the soil organic matter (SOM) composition. Positive correlations between the relative abundance of LIPID (lipids, alkanes/alkenes), ALKYL (alkylaromatics), and suberin and MeHg concentrations indicate that these SOM groups might be related to MeHg formation. Biochar enhanced the releasing and methylation of Hg by promoting the mobilization of Fe(oxyhydr)oxides and alternation of carbon chemistry under dynamic Eh conditions. There is an unexpected environmental risk associated with biochar application to paddy soils under dynamic Eh condition, and one should be aware this risk when applying biochar aiming to minimize human Hg exposure health risks via rice consumption.

Multi-Mixed Metal Hydroxide as a Strong Stratigraphic Nanoclay Inhibitor in Solid-Free Drilling Fluid.

Solid-free drilling fluid has more advantages as a new type of drilling fluid compared with traditional drilling fluid, such as improving drilling efficiency, protecting oil and not having clay particles clog the oil and gas layer. In this study, Zn/Cu/Fe-doped magnesium-aluminum hydroxide (Mg-Al MMH) was prepared using the co-precipitation method and evaluated in solid-free drilling fluid. The inhibition mechanism of synthesized hydroxide was analyzed by X-ray diffraction, laser particle-size analysis and thermogravimetric analysis. The samples were directly used as drilling fluid base muds for performance evaluation. The results showed that the linear expansion rate of 4% M6-Fe was only 12.32% at room temperature within 2 h, that the linear expansion rate was 20.28% at 90 °C and that the anti-swelling rate was 81.16% at room temperature, indicating that it has a strong inhibition ability at both room temperature and at high temperatures. Meanwhile, the possibility of multi-mixed metal hydroxide as a drilling fluid base mud is discussed in this study. We found that 4% M6-Fe exhibited low viscosity, a high YP/PV ratio and high temperature resistance, and its apparent viscosity retention rate reached 100% rolled at 200 °C for 16 h, with a YP/PV ratio of 2.33.

Herbal plants- and rice straw-derived biochars reduced metal mobilization in fishpond sediments and improved their potential as fertilizers.

Fishpond sediments are rich in organic carbon and nutrients; thus, they can be used as potential fertilizers and soil conditioners. However, sediments can be contaminated with toxic elements (TEs), which have to be immobilized to allow sediment reutilization. Addition of biochars (BCs) to contaminated sediments may enhance their nutrient content and stabilize TEs, which valorize its reutilization. Consequently, this study evaluated the performance of BCs derived from Taraxacum mongolicum Hand-Mazz (TMBC), Tribulus terrestris (TTBC), and rice straw (RSBC) for Cu, Cr, and Zn stabilization and for the enhancement of nutrient content in the fishpond sediments from San Jiang (SJ) and Tan Niu (TN), China. All BCs, particularly TMBC, reduced significantly the average concentrations of Cr, Cu, and Zn in the overlying water (up to 51% for Cr, 71% for Cu, and 68% for Zn) and in the sediments pore water (up to 77% for Cr, 76% for Cu, and 50% for Zn), and also reduced metal leachability (up to 47% for Cr, 60% for Cu, and 62% for Zn), as compared to the control. The acid soluble fraction accounted for the highest portion of the total content of Cr (43-44%), Cu (38-43%), and Zn (42-45%), followed by the reducible, oxidizable, and the residual fraction; this indicates the high potential risk. As compared with the control, TMBC was more effective in reducing the average concentrations of the acid soluble Cr (15-22%), Cu (35-53%), and Zn (21-39%). Added BCs altered the metals acid soluble fraction by shifting it to the oxidizable and residual fractions. Moreover, TMBC improved the macronutrient status in both sediments. This work provides a pathway for TEs remediation of sediments and gives novel insights into the utilization of BC-treated fishpond sediments as fertilizers for crop production.

Remediation of Cd and Cu contaminated water and soil using novel nanomaterials derived from sugar beet processing- and clay brick factory-solid wastes.

Producing nanomaterials from hazardous wastes for water and soil treatment is of great concern. Here, we produced and fully characterized two novel nanomaterials from sugar beet processing (SBR)- and brick factory-residuals (BFR) and assed their ability for Cd and Cu sorption in water and reducing metal availability in a contaminated soil. The SBR removed up to 99% of Cu and 91% of Cd in water, and exhibited a significantly faster and higher sorption capacity (qmax (g kg-1) = 1111.1 for Cu and 33.3 for Cd) than BFR (qmax (g kg-1) = 33.3 for Cu and 10.0 for Cd), even at acidic pH. Soil metal availability was significantly reduced by SBR (up to 57% for Cu and 86% for Cd) and BFR (up to 36% for Cu and 68% for Cd) compared to the unamended soil. The higher removal efficacy of SBR over BFR could be attributed to its higher alkalinity (pH = 12.5), carbonate content (82%), and specific surface area, as well as the activity of hydroxyl -OH and Si-O groups. The nano-scale SBR and BFR, the former particularly, are novel, of low cost, and environmental friendly amendments that can be used for the remediation of metal-contaminated water and soil.

Detection and phylogenetic characterization of human hepatitis E virus strains, Czech Republic.

To determine the origin of hepatitis E virus in the Czech Republic, we analyzed patient clinical samples. Five isolates of genotypes 3e, 3f, and 3g were obtained. Their genetic relatedness with Czech strains from domestic pigs and wild boars and patient recollections suggest an autochthonous source likely linked to consumption of contaminated pork.

Phase Composition of Silica Fume-Portland Cement Systems Formed under Hydrothermal Curing Evaluated by FTIR, XRD, and TGA.

Two substitution levels of Portland cement by silica fume (SF; 30 and 50 mass%) and three hydrothermal treatment regimes (0.5, 1.2, and 2 MPa and 165, 195, and 220 °C for 7 days, respectively) were selected for the investigation of high-temperature phase formation. A combination of thermogravimetric, X-ray diffraction, and Fourier transform infrared analyses in the mid-IR region was used to overcome the shortcomings of individual techniques for the identification of these complex systems. Changes in molecular water amounts, the polymerization degree of silicate chains, or their decomposition due to transformations and crystallization of phases at hydrothermal conditions were observed and discussed concerning composition. Contrary to the calciochondrite, hydrogrossular phases, α-C2SH, and jaffeite detected in the systems without SF, a decrease in CaO/SiO2 ratio resulted in the formation of stable tobermorite in the case of 30 mass% SF, whilst calcium hydrogen silicate, gyrolite, and cowlesite were identified as more thermally stable phases in the samples with 50 mass% SF.

Synthesis of Mg-Al Hydrotalcite Clay with High Adsorption Capacity.

A novel Mg-Al metal oxide has been successfully synthesized by the calcination of hierarchical porous Mg-Al hydrotalcite clay obtained by using filter paper as a template under hydrothermal conditions. Various characterizations of the obtained nanoscale oxide particles verified the uniform dispersion of Mg-Al metal oxides on the filter paper fiber, which had a size of 2-20 nm and a highest specific surface area (SSA) of 178.84 m2/g. Structural characterization revealed that the as-prepared Mg-Al metal oxides preserved the tubular morphology of the filter paper fibers. Further experiments showed that the as-synthesized Mg-Al metal oxides, present at concentrations of 0.3 g/L, could efficiently remove sulfonated lignite from oilfield wastewater (initial concentration of 200 mg/L) in a neutral environment (pH = 7) at a temperature of 298 K. An investigation of the reaction kinetics found that the adsorption process of sulfonated lignite (SL) on biomorphic Mg-Al metal oxides fits a Langmuir adsorption model and pseudo-second-order rate equation. Thermodynamic calculations propose that the adsorption of sulfonated lignite was spontaneous, endothermic, and a thermodynamically feasible process.