Gram-scale bottom-up flash graphene synthesis.

Most bulk-scale graphene is produced by a top-down approach, exfoliating graphite, which often requires large amounts of solvent with high-energy mixing, shearing, sonication or electrochemical treatment1-3. Although chemical oxidation of graphite to graphene oxide promotes exfoliation, it requires harsh oxidants and leaves the graphene with a defective perforated structure after the subsequent reduction step3,4. Bottom-up synthesis of high-quality graphene is often restricted to ultrasmall amounts if performed by chemical vapour deposition or advanced synthetic organic methods, or it provides a defect-ridden structure if carried out in bulk solution4-6. Here we show that flash Joule heating of inexpensive carbon sources-such as coal, petroleum coke, biochar, carbon black, discarded food, rubber tyres and mixed plastic waste-can afford gram-scale quantities of graphene in less than one second. The product, named flash graphene (FG) after the process used to produce it, shows turbostratic arrangement (that is, little order) between the stacked graphene layers. FG synthesis uses no furnace and no solvents or reactive gases. Yields depend on the carbon content of the source; when using a high-carbon source, such as carbon black, anthracitic coal or calcined coke, yields can range from 80 to 90 per cent with carbon purity greater than 99 per cent. No purification steps are necessary. Raman spectroscopy analysis shows a low-intensity or absent D band for FG, indicating that FG has among the lowest defect concentrations reported so far for graphene, and confirms the turbostratic stacking of FG, which is clearly distinguished from turbostratic graphite. The disordered orientation of FG layers facilitates its rapid exfoliation upon mixing during composite formation. The electric energy cost for FG synthesis is only about 7.2 kilojoules per gram, which could render FG suitable for use in bulk composites of plastic, metals, plywood, concrete and other building materials.

A comparison of the pharmacodynamic effects of intravenous ketamine-xylazine with alfaxalone in mute swans (Cygnus olor) presenting at a wildlife veterinary hospital.

OBJECTIVE: To compare effects of intravenous (IV) alfaxalone with ketamine-xylazine combination on anaesthetic induction, recovery and cardiopulmonary variables in mute swans. STUDY DESIGN: Randomized, controlled, clinical study. ANIMALS: A group of 58 mute swans. METHODS: Swans were given either alfaxalone (10 mg kg-1; group A) or a combination of ketamine (12.5 mg kg-1) and xylazine (0.28 mg kg-1) (group KX) IV. Heart and respiratory rates, end-tidal carbon dioxide and peripheral haemoglobin oxygen saturation were recorded at 5 minute intervals during anaesthesia. Time from anaesthetic induction to intubation, from cessation of isoflurane to extubation, to lifting head, sternal recumbency and absence of head/neck ataxia were recorded. Anaesthetic and recovery quality were scored (1 = very poor; 5 = excellent). Data are presented as median (interquartile range). Significance was set at p < 0.05. RESULTS: In group A, 44% (12/27) of swans required mechanical ventilation for 2-14 minutes versus 3.2% (1/31) of swans in group KX (p = 0.0002). Heart rate was higher in group A than in group KX [146 (127-168) versus 65.5 (56-78) beats minute-1, respectively; p < 0.0001]. The isoflurane concentration required to maintain anaesthesia was higher in group A than in group KX [2.5% (2.0-3.0%) versus 1.5% (1.0-2.0%), respectively; p = 0.0001]. Time from cessation of isoflurane administration to lifting head was significantly longer in group A than in group KX [12 (9-17) versus 6 (4-7.75) minutes, respectively; p < 0.0001]. Anaesthesia quality scores were significantly better in group KX than in group A [4 (4-5) versus 4 (3-4), respectively; p = 0.0011], as were recovery scores [4 (3-5) versus 2 (2-3), respectively; p = 0.0005]. CONCLUSIONS AND CLINICAL RELEVANCE: Alfaxalone is a suitable anaesthetic induction agent for use in mute swans. There is a greater incidence of postinduction apnoea and a higher incidence of agitation on recovery with alfaxalone than with ketamine-xylazine.

Exploring Photothermal Pathways via in Situ Laser Heating in the Transmission Electron Microscope: Recrystallization, Grain Growth, Phase Separation, and Dewetting in Ag0.5Ni0.5 Thin Films.

A new optical delivery system has been developed for the (scanning) transmission electron microscope. Here we describe the in situ and "rapid ex situ" photothermal heating modality of the system, which delivers >200 mW of optical power from a fiber-coupled laser diode to a 3.7 µm radius spot on the sample. Selected thermal pathways can be accessed via judicious choices of the laser power, pulse width, number of pulses, and radial position. The long optical working distance mitigates any charging artifacts and tremendous thermal stability is observed in both pulsed and continuous wave conditions, notably, no drift correction is applied in any experiment. To demonstrate the optical delivery system's capability, we explore the recrystallization, grain growth, phase separation, and solid state dewetting of a Ag0.5Ni0.5 film. Finally, we demonstrate that the structural and chemical aspects of the resulting dewetted films was assessed.

High performance top-gated multilayer WSe2 field effect transistors.

In this paper, high performance top-gated WSe2 field effect transistor (FET) devices are demonstrated via a two-step remote plasma assisted ALD process. High-quality, low-leakage aluminum oxide (Al2O3) gate dielectric layers are deposited onto the WSe2 channel using a remote plasma assisted ALD process with an ultrathin (∼1 nm) titanium buffer layer. The first few nanometers (∼2 nm) of the Al2O3 dielectric film is deposited at relatively low temperature (i.e. 50 °C) and remainder of the film is deposited at 150 °C to ensure the conformal coating of Al2O3 on the WSe2 surface. Additionally, an ultra-thin titanium buffer layer is introduced at the WSe2 channel surface prior to ALD process to mitigate oxygen plasma induced doping effects. Excellent device characteristics with current on-off ratio in excess of 106 and a field effect mobility as high as 70.1 cm2 V-1 s-1 are achieved in a few-layer WSe2 FET device with a 30 nm Al2O3 top-gate dielectric. With further investigation and careful optimization, this method can play an important role for the realization of high performance top gated FETs for future optoelectronic device applications.

In Situ Mitigation of Subsurface and Peripheral Focused Ion Beam Damage via Simultaneous Pulsed Laser Heating.

Focused helium and neon ion (He(+)/Ne(+)) beam processing has recently been used to push resolution limits of direct-write nanoscale synthesis. The ubiquitous insertion of focused He(+)/Ne(+) beams as the next-generation nanofabrication tool-of-choice is currently limited by deleterious subsurface and peripheral damage induced by the energetic ions in the underlying substrate. The in situ mitigation of subsurface damage induced by He(+)/Ne(+) ion exposures in silicon via a synchronized infrared pulsed laser-assisted process is demonstrated. The pulsed laser assist provides highly localized in situ photothermal energy which reduces the implantation and defect concentration by greater than 90%. The laser-assisted exposure process is also shown to reduce peripheral defects in He(+) patterned graphene, which makes this process an attractive candidate for direct-write patterning of 2D materials. These results offer a necessary solution for the applicability of high-resolution direct-write nanoscale material processing via focused ion beams.

Surface polarization enhanced Seebeck effects in vertical multi-layer metal-polymer-metal thin-film devices.

We explore a new mechanism to develop Seebeck effects by using temperature-dependent surface polarization based on vertical multi-layer Al-P3HT:PCBM-Al thin-film devices. Here, the temperature-dependent surface polarization functions as an additional driving force, as compared with the traditional driving force from the entropy difference, to diffuse the charge carriers under a temperature gradient towards the development of Seebeck effects. The temperature-dependent surface polarization is essentially generated by both the thermally dependent polarization through the charge-phonon coupling mechanism and the thermally modulated interface dipoles by Fermi electrons. It is noted that the entropy difference often causes an inverse relationship between the Seebeck coefficient and electrical conductivity in thermoelectric developments. However, this temperature-dependent surface polarization provides a mechanism allowing a co-operative relationship between the Seebeck coefficient and electrical conductivity. We demonstrate simultaneously the enhanced Seebeck coefficient and electrical conductivity by using the dielectric interface through the temperature-dependent surface polarization to diffuse charge carriers in the Al-MoO3-P3HT:PCBM-Al thin-film device.

Combinatorial Cu-Ni Alloy Thin-Film Catalysts for Layer Number Control in Chemical Vapor-Deposited Graphene.

We synthesized a combinatorial library of CuxNi1−x alloy thin films via co-sputtering from Cu and Ni targets to catalyze graphene chemical vapor deposition. The alloy morphology, composition, and microstructure were characterized via scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and X-ray diffraction (XRD), respectively. Subsequently, the CuxNi1−x alloy thin films were used to grow graphene in a CH4-Ar-H2 ambient at atmospheric pressure. The underlying rationale is to adjust the CuxNi1−x composition to control the graphene. Energy dispersive x-ray spectroscopy (EDS) analysis revealed that a continuous gradient of CuxNi1−x (25 at. % < x < 83 at.%) was initially achieved across the 100 mm diameter substrate (~0.9%/mm composition gradient). The XRD spectra confirmed a solid solution was realized and the face-centered cubic lattice parameter varied from ~3.52 to 3.58 A˙, consistent with the measured composition gradient, assuming Vegard's law. Optical microscopy and Raman analysis of the graphene layers suggest single layer growth occurs with x > 69 at.%, bilayer growth dominates from 48 at.% < x < 69 at.%, and multilayer (≥3) growth occurs for x < 48 at.%, where x is the Cu concentration. Finally, a large area of bi-layer graphene was grown via a CuxNi1−x catalyst with optimized catalyst composition and growth temperature.

Risk and the Republican National Convention: Application of the Novel COVID-19 Operational Risk Assessment.

The United States Centers for Disease Control and Prevention and the World Health Organization broadly categorize mass gathering events as high risk for amplification of coronavirus disease 2019 (COVID-19) spread in a community due to the nature of respiratory diseases and the transmission dynamics. However, various measures and modifications can be put in place to limit or reduce the risk of further spread of COVID-19 for the mass gathering. During this pandemic, the Johns Hopkins University Center for Health Security produced a risk assessment and mitigation tool for decision-makers to assess SARS-CoV-2 transmission risks that may arise as organizations and businesses hold mass gatherings or increase business operations: The JHU Operational Toolkit for Businesses Considering Reopening or Expanding Operations in COVID-19 (Toolkit). This article describes the deployment of a data-informed, risk-reduction strategy that protects local communities, preserves local health-care capacity, and supports democratic processes through the safe execution of the Republican National Convention in Charlotte, North Carolina. The successful use of the Toolkit and the lessons learned from this experience are applicable in a wide range of public health settings, including school reopening, expansion of public services, and even resumption of health-care delivery.

A protein processing filter method for bacterial identification by mass spectrometry-based proteomics.

A "one-pot" alternative method for processing proteins and isolating peptide mixtures from bacterial samples is presented for liquid chromatography-tandem mass spectrometry (LC-MS/MS) analysis and data reduction. The conventional in-solution digestion of the protein contents of bacteria is compared to a small disposable filter unit placed inside a centrifuge vial for processing and digestion of bacterial proteins. Each processing stage allows filtration of excess reactants and unwanted byproduct while retaining the proteins. Upon addition of trypsin, the peptide mixture solution is passed through the filter while retaining the trypsin enzyme. The peptide mixture is then analyzed by LC-MS/MS with an in-house BACid algorithm for a comparison of the experimental unique peptides to a constructed proteome database of bacterial genus, specie, and strain entries. The concentration of bacteria was varied from 10 × 10(7) to 3.3 × 10(3) cfu/mL for analysis of the effect of concentration on the ability of the sample processing, LC-MS/MS, and data analysis methods to identify bacteria. The protein processing method and dilution procedure result in reliable identification of pure suspensions and mixtures at high and low bacterial concentrations.

Anesthesia of Tibetan yak (Bos grunniens) using thiafentanil - xylazine and carfentanil - xylazine.

The use of 0.025 +/- 0.012 mg/kg (median +/- interquartile range) thiafentanil with 0.15 +/- 0.03 mg/kg xylazine (TX) and 0.011 +/- 0.0015 mg/kg carfentanil with 0.25 +/- 0.093 mg/kg xylazine (CX), with dosages based on estimated bodyweight, was used in the anesthesia of 37 Tibetan yak (Bos grunniens) housed within a drive-through animal park setting. The median time to lateral recumbency was 5 and 7 min for each group, respectively. With the addition of propofol in 8 CX animals and 17 TX animals, the anesthetic plane was suitable for a wide range of procedures. The median time to standing recovery following administration of naltrexone was 4 +/- 3.5 min with TX and 7 +/- 1.5 min with CX. There was one fatality and one case of renarcotization in the TX group. Overall, the dosages used in the study provided a reliable and useful anesthetic induction protocol, with TX animals demonstrating a more rapid induction and recovery with less cardiac depression than CX animals.

High-Resolution Laser-Induced Graphene from Photoresist.

The fabrication of patterned graphene electronics at high resolution is an important challenge for many applications in microelectronics. Here, we demonstrate the conversion of positive photoresist (PR), commonly employed in the commercial manufacture of consumer electronics, into laser-induced graphene (LIG). Sequential lasing converts the PR photopolymer first into amorphous carbon, then to photoresist-derived LIG (PR-LIG). The resulting material possesses good conductivity and is easily doped with metal or other additives for additional functionality. Furthermore, photolithographic exposure of PR prior to lasing enables the generation of PR-LIG patterns small enough to be invisible to the naked eye. By exploiting PR as a photopatternable LIG precursor, PR-LIG can be synthesized with a spatial resolution of ∼10 µm, up to 15 times smaller than conventional LIG patterning methods. The patterning of these small PR-LIG features could offer a powerful and broadly accessible strategy for the fabrication of microscale LIG-derived nanocomposites for on-chip devices.

Ultrafast and Controllable Phase Evolution by Flash Joule Heating.

Flash Joule heating (FJH), an advanced material synthesis technique, has been used for the production of high-quality carbon materials. Direct current discharge through the precursors by large capacitors has successfully converted carbon-based starting materials into bulk quantities of turbostratic graphene by the FJH process. However, the formation of other carbon allotropes, such as nanodiamonds and concentric carbon materials, as well as the covalent functionalization of different carbon allotropes by the FJH process, remains challenging. Here, we report the solvent-free FJH synthesis of three different fluorinated carbon allotropes: fluorinated nanodiamonds, fluorinated turbostratic graphene, and fluorinated concentric carbon. This is done by millisecond flashing of organic fluorine compounds and fluoride precursors. Spectroscopic analysis confirms the modification of the electronic states and the existence of various short-range and long-range orders in the different fluorinated carbon allotropes. The flash-time-dependent relationship is further demonstrated to control the phase evolution and product compositions.

Millisecond Conversion of Metastable 2D Materials by Flash Joule Heating.

Controllable phase engineering is vital for precisely tailoring material properties since different phase structures have various electronic states and atomic arrangements. Rapid synthesis of thermodynamically metastable materials, especially two-dimensional metastable materials, with high efficiency and low cost remains a large challenge. Here we report flash Joule heating (FJH) as an electrothermal method to achieve the bulk conversion of transition metal dichalcogenides, MoS2 and WS2, from 2H phases to 1T phases in milliseconds. The conversions can reach up to 76% of flash MoS2 using tungsten powder as conductive additive. Different degrees of phase conversion can be realized by controlling the FJH conditions, such as reaction duration and additives, which allows the study of ratio-dependent properties. First-principles calculations confirm that structural processes associated with the FJH, such as vacancy formation and charge accumulation, result in stabilization of the 1T phases. FJH offers rapid access to bulk quantities of the hitherto hard-to-access 1T phases, a promising method for further fundamental research and diverse applications of metastable phases.

Identification of Yersinia pestis and Escherichia coli strains by whole cell and outer membrane protein extracts with mass spectrometry-based proteomics.

Whole cell protein and outer membrane protein (OMP) extracts were compared for their ability to differentiate and delineate the correct database organism to an experimental sample and for the degree of dissimilarity to the nearest neighbor database organism strains. These extracts were isolated from pathogenic and nonpathogenic strains of Yersinia pestis and Escherichia coli using ultracentrifugation and a sarkosyl extraction method followed by protein digestion and analysis using liquid chromatography tandem mass spectrometry (MS). Whole cell protein extracts contain many different types of proteins resident in an organism at a given phase in its growth cycle. OMPs, however, are often associated with virulence in Gram-negative pathogens and could prove to be model biomarkers for strain differentiation among bacteria. The mass spectra of bacterial peptides were searched, using the SEQUEST algorithm, against a constructed proteome database of microorganisms in order to determine the identity and number of unique peptides for each bacterial sample. Data analysis was performed with the in-house BACid software. It calculated the probabilities that a peptide sequence assignment to a product ion mass spectrum was correct and used accepted spectrum-to-sequence matches to generate a sequence-to-bacterium (STB) binary matrix of assignments. Validated peptide sequences, either present or absent in various strains (STB matrices), were visualized as assignment bitmaps and analyzed by the BACid module that used phylogenetic relationships among bacterial species as part of a decision tree process. The bacterial classification and identification algorithm used assignments of organisms to taxonomic groups (phylogenetic classification) based on an organized scheme that begins at the phylum level and follows through the class, order, family, genus, and species to the strain level. For both Gram-negative organisms, the number of unique distinguishing proteins arrived at by the whole cell method was less than that of the OMP method. However, the degree of differentiation measured in linkage distance units on a dendrogram with the OMP extract showed similar or significantly better separation than the whole cell protein extract method between the sample and correct database match compared to the next nearest neighbor. The nonpathogenic Y. pestis A1122 strain used does not have its genome available, and thus, data analysis resulted in an equal similarity index to the nonpathogenic 91001 and pathogenic Antiqua and Nepal 516 strains for both extraction methods. Pathogenic and nonpathogenic strains of E. coli were correctly identified with both protein extraction methods, and the pathogenic Y. pestis CO92 strain was correctly identified with the OMP procedure. Overall, proteomic MS proved useful in the analysis of unique protein assignments for strain differentiation of E. coli and Y. pestis. The power of bacterial protein capture by the whole cell protein and OMP extraction methods was highlighted by the data analysis techniques and revealed differentiation and similarities between the two protein extraction approaches for bacterial delineation capability.

Double-blind characterization of non-genome-sequenced bacteria by mass spectrometry-based proteomics.

Due to the possibility of a biothreat attack on civilian or military installations, a need exists for technologies that can detect and accurately identify pathogens in a near-real-time approach. One technology potentially capable of meeting these needs is a high-throughput mass spectrometry (MS)-based proteomic approach. This approach utilizes the knowledge of amino acid sequences of peptides derived from the proteolysis of proteins as a basis for reliable bacterial identification. To evaluate this approach, the tryptic digest peptides generated from double-blind biological samples containing either a single bacterium or a mixture of bacteria were analyzed using liquid chromatography-tandem mass spectrometry. Bioinformatic tools that provide bacterial classification were used to evaluate the proteomic approach. Results showed that bacteria in all of the double-blind samples were accurately identified with no false-positive assignment. The MS proteomic approach showed strain-level discrimination for the various bacteria employed. The approach also characterized double-blind bacterial samples to the respective genus, species, and strain levels when the experimental organism was not in the database due to its genome not having been sequenced. One experimental sample did not have its genome sequenced, and the peptide experimental record was added to the virtual bacterial proteome database. A replicate analysis identified the sample to the peptide experimental record stored in the database. The MS proteomic approach proved capable of identifying and classifying organisms within a microbial mixture.

Laminated Laser-Induced Graphene Composites.

Laser-induced graphene (LIG) is a porous graphene foam generated by lasing carbon-based precursors. Compositing LIG expands the spectrum of applications for which the material may be used. Techniques for scale-up of LIG composites will be essential as the technology approaches commercialization. Roll-to-roll processing is of special interest, as precisely controlled patterning can be performed in conjunction with continuous formation of composites. Here, we demonstrate a simple lamination compositing method that is compatible with roll-to-roll processing and yields functional, patterned, and multilayered LIG composites with various thermoplastic films. Multiple lamination steps are used to encapsulate LIG within composites. We also demonstrate several applications for LIG that have been enabled by the lamination compositing technique. These include robust flexible electrodes generated through laminating copper foil strips into the LIG composite, LIG-based triboelectric nanogenerators to harvest waste mechanical energy, antimicrobial LIG composite bandages with varying hydrophobicity, and LIG puncture detectors.

Laser-Induced Silicon Oxide for Anode-Free Lithium Metal Batteries.

The development of a rechargeable Li metal anode (LMA) is an important milestone for improved battery technology. Practical issues hindering LMAs are the formation of Li dendrites and inactive Li during plating and stripping processes, which can cause short circuits, thermal runaway, and low coulombic efficiency (CE). Here, the use of a laser-induced silicon oxide (LI-SiOx ) layer derived from a commercial adhesive tape to improve the reversibility of Li metal batteries (LMBs) is studied. The silicone-based adhesive of the tape is converted by a commercial infrared laser into a homogeneous porous SiOx layer deposited directly over the current collector. The coating results in superior performance by suppressing the formation of Li dendrites and inactive Li and presenting higher average CE of 99.3% (2.0 mAh cm-2 at 2.0 mA cm-2 ) compared to bare electrodes. The thickness and morphology of the deposited Li is investigated, revealing a different mechanism of Li deposition on coated electrodes. The laser coating affords a method that is fast and avoids the use of toxic organic solvents and extensive drying times. The improved performance with the SiOx coating is demonstrated in LMB with a zero-excess ("anode-free") configuration where a 100% improved performance is verified.

High-Resolution Laser-Induced Graphene. Flexible Electronics beyond the Visible Limit.

Laser-induced graphene (LIG) is a multifunctional graphene foam that is commonly direct-written with an infrared laser into a carbon-based precursor material. Here, a visible 405 nm laser is used to directly convert polyimide into LIG. This enabled the formation of LIG with a spatial resolution of ∼12 µm and a thickness of <5 µm. The spatial resolution enabled by the relatively smaller focused spot size of the 405 nm laser represents a >60% reduction in LIG feature sizes reported in prior publications. This process occurs in situ in an SEM chamber, thus allowing direct observation of LIG formation. The reduced size of the LIG features enables the direct-write formation of flexible electronics that are not visible to the unaided eye. A humidity sensor is demonstrated which could detect human breath with a response time of 250 ms. With the growing interest in LIG for flexible electronics and sensors, finer features can greatly expand its utility.

Flash Graphene Morphologies.

Flash Joule heating (FJH) can convert almost any carbon-based precursor into bulk quantities of graphene. This work explores the morphologies and properties of flash graphene (FG) generated from carbon black. It is shown that FG is partially comprised of sheets of turbostratic FG (tFG) that have a rotational mismatch between neighboring layers. The remainder of the FG is wrinkled graphene sheets that resemble nongraphitizing carbon. To generate high quality tFG sheets, a FJH duration of 30-100 ms is employed. Beyond 100 ms, the turbostratic sheets have time to AB-stack and form bulk graphite. Atomistic simulations reveal that generic thermal annealing yields predominantly wrinkled graphene which displays minimal to no alignment of graphitic planes, as opposed to the high-quality tFG that might be formed under the direct influence of current conducted through the material. The tFG was easily exfoliated via shear, hence the FJH process has the potential for bulk production of tFG without the need for pre-exfoliation using chemicals or high energy mechanical shear.

Direct Write of 3D Nanoscale Mesh Objects with Platinum Precursor via Focused Helium Ion Beam Induced Deposition.

The next generation optical, electronic, biological, and sensing devices as well as platforms will inevitably extend their architecture into the 3rd dimension to enhance functionality. In focused ion beam induced deposition (FIBID), a helium gas field ion source can be used with an organometallic precursor gas to fabricate nanoscale structures in 3D with high-precision and smaller critical dimensions than focused electron beam induced deposition (FEBID), traditional liquid metal source FIBID, or other additive manufacturing technology. In this work, we report the effect of beam current, dwell time, and pixel pitch on the resultant segment and angle growth for nanoscale 3D mesh objects. We note subtle beam heating effects, which impact the segment angle and the feature size. Additionally, we investigate the competition of material deposition and sputtering during the 3D FIBID process, with helium ion microscopy experiments and Monte Carlo simulations. Our results show complex 3D mesh structures measuring ~300 nm in the largest dimension, with individual features as small as 16 nm at full width half maximum (FWHM). These assemblies can be completed in minutes, with the underlying fabrication technology compatible with existing lithographic techniques, suggesting a higher-throughput pathway to integrating FIBID with established nanofabrication techniques.