Effects of Bioactive Compounds on Odontogenic Differentiation and Mineralization.

Direct pulp capping involves the placement of dental materials directly onto vital pulp tissues after deep caries removal to stimulate the regeneration of reparative dentin. This physical barrier will serve as a "biological seal" between these materials and the pulp tissue. Although numerous direct pulp capping materials are available, the use of small bioactive compounds that can potently stimulate and expedite reparative dentin formation is still underexplored. Here, the authors compared and evaluated the pro-osteogenic and pro-odontogenic effects of 4 small bioactive compounds- phenamil (Phen), purmorphamine (Pur), genistein (Gen), and metformin (Met). The authors found that these compounds at noncytotoxic concentrations induced differentiation and mineralization of preosteoblastic MC3T3-E1 cells and preodontoblastic dental pulp stem cells (DPSCs) in a dose-dependent manner. Among them, Phen consistently and potently induced differentiation and mineralization in vitro. A single treatment with Phen was sufficient to enhance the mineralization potential of DPSCs in vitro. More importantly, Phen-treated DPSCs showed enhanced odontogenic differentiation and mineralization in vivo. Our study suggests that these small bioactive compounds merit further study for their potential clinical use as pulp capping materials.

The oxygen-shielded air-acetylene flame in emission analysis.

Flame-emission studies have been made on 18 elements in the inner zone of an oxygen-shielded air-acetylene flame. The shielded flame gave higher emission sensitivity that that of the C(2)H(2)N(2)O flame for Cu and Tl, and comparable sensitivity for a number of other elements, but poorer sensitivity for elements forming stable refractory oxides in flames. The inner zone of the shielded flame has low emission-background and high flame-temperature, permitting good analytical sensitivity to be obtained with relatively low-resolution optical equipment.

Effect of application technique and dentin bonding agent interaction on shear bond strength.

This study evaluated the interaction of five clinical application techniques and the shear bond strength of four DBAs (OptiBond FL, Clearfil SE Bond, PQ1 and Prime & Bond NT). A hybrid resin composite (Herculite XRV restorative resin) was attached to human dentin surfaces using five application techniques: Group A--adhesive spread with a 3M brush for 30 seconds, followed by compressed air 0.5 cm from the surface for one second to remove the excess adhesive. Group B--adhesive spread with a 3M brush for 30 seconds, followed by compressed air 0.5 cm from the surface for three seconds to remove the excess adhesive. Group C--adhesive spread with 3M brush for 30 seconds, excess adhesive removed with a clean brush, two strokes side by side, no compressed air. Group D--adhesive spread with a Micro-applicator brush for 30 seconds followed by compressed air 0.5 cm from the surface for one second to remove the excess adhesive. Group E--adhesive spread with a Micro-applicator brush for 30 seconds, the excess adhesive removed with a clean brush, two strokes side by side and no compressed air. The specimens were stored in distilled water at 37 degrees C for 24 hours, followed by thermocycling between 5 degrees C and 55 degrees C for 1,000 cycles. The shear bond strengths were determined on a universal testing machine operating with a crosshead speed of 5 mm/minute. The fracture sites were examined by 20x stereo microscope to determine the type of failure that occurred during the debonding procedure. Bond strength data were compared with analysis of variance at a significance level of p<0.05. Post hoc comparisons of means were performed with t-tests with p-values adjusted for multiple comparisons. This in vitro study concluded that there was an interaction between the application technique and bonding agent tested. All DBAs utilized the one-second compressed air technique, which yielded the highest bond strengths.

Comparison of pulp responses to resin composites.

Diverse reports have described how various types of adhesive systems cause disastrous pulp necrosis, chronic severe inflammation or failure to stimulate any pulp reactions. This article reports on the effects of five common adhesive systems and how they compare in terms of pulp injury as measured by odontoblast survival or dentin regeneration and reactionary dentin formation. One hundred and thirty Class V pulp, non-exposed cavities were prepared in non-human primate teeth and were restored with five different adhesive systems. After a period of time between 3 and 172 days, the teeth were extracted, fixed, processed and examined histomorphometrically. Bacterial microleakage was detected with McKays stain and inflammation was categorized according to the International Organization for Standardization (ISO) criteria. The number of odontoblasts and the area of reactionary dentin were measured. Pulp reactions of all adhesive systems were generally minimal, although some systems permitted bacterial microleakage in 33% of restorations, and some other systems were associated with pulp inflammation in 22% of restorations. These observations suggest that adhesive systems provide acceptable biocompatibility, however, there is strong potential for improvement.

Pulmonary adenomatosis (jaagsiekte) of sheep in Canada.

Sheep pulmonary adenomatosis has recently been reported in Canada. The literature is briefly reviewed and an account of the present status of the disease in Canada is described.Sheep pulmonary adenomatosis was first diagnosed in Canada in December 1979 in a first generation descendent of sheep imported from Great Britain. In March 1980 two further cases of sheep pulmonary adenomatosis were diagnosed in a second flock. A total of 43 sheep involving eight flocks from five provinces have been observed from December, 1979 to May, 1981. The clinical signs and laboratory findings were similar to those described in sheep from other countries. It is estimated that 30% of Canadian flocks may contain sheep imported from Great Britain during the 1970's.