Synthesis and Physical Properties of the Misfit Layered Compound (EuS)1.13(NbSe2)2.

A new misfit layered compound with the stoichiometry (EuS)1+δ(NbSe2)2 (δ ≈ 0.13) has been successfully synthesized. High-resolution transmission electron microscopy and powder X-ray diffraction confirm the misfit structure with (EuS)-(EuS) spacing of 18.30(1) Å. Magnetization, electrical resistivity, heat capacity, and thermal transport measurements show that the material is a heavily doped semiconductor or poor metal with a low thermal conductivity of ∼1 W/m K and an antiferromagnetic ordering transition at TN = 4.7 K. In contrast to the parent materials, the misfit is neither ferromagnetic nor superconducting down to T = 0.4 K. We find evidence of a field-driven transition to a ferromagnetic state due to reorientation of ferromagnetic EuS layers at µoH = 0.5 T at T = 2 K.

Grain Boundary Plane Measurement Using Transmission Electron Microscopy Automated Crystallographic Orientation Mapping for Atom Probe Tomography Specimens.

Grain boundaries are critical in determining the properties of materials, including mechanical stability, conductivity, and corrosion resistance. The specific properties of materials depend not only on the misorientation of the crystals, the three most commonly characterized parameters, but also on the angle of the grain boundary plane between the two crystals, the final two parameters in the five-parameter macroscopic description of the grain boundary. The method presented here allows for the direct measurement of all five parameters of the grain boundary in a transmission electron microscopy specimen of various morphologies. This is especially applicable to atom probe specimens, where only a single-tilt axis is generally available, allowing the crystallographic description to be matched to the detailed chemical data available in the atom probe tomography. This method provides a platform for efficient grain boundary analysis in unique samples, saving operator time and allowing for ease of acquisition and interpretation in comparison with traditional electron diffraction methods.

A percolation theory for designing corrosion-resistant alloys.

Iron-chromium and nickel-chromium binary alloys containing sufficient quantities of chromium serve as the prototypical corrosion-resistant metals owing to the presence of a nanometre-thick protective passive oxide film1-8. Should this film be compromised by a scratch or abrasive wear, it reforms with little accompanying metal dissolution, a key criterion for good passive behaviour. This is a principal reason that stainless steels and other chromium-containing alloys are used in critical applications ranging from biomedical implants to nuclear reactor components9,10. Unravelling the compositional dependence of this electrochemical behaviour is a long-standing unanswered question in corrosion science. Herein, we develop a percolation theory of alloy passivation based on two-dimensional to three-dimensional crossover effects that accounts for selective dissolution and the quantity of metal dissolved during the initial stage of passive film formation. We validate this theory both experimentally and by kinetic Monte Carlo simulation. Our results reveal a path forward for the design of corrosion-resistant metallic alloys.

Chemical and Physical Characterization of 3D Printer Aerosol Emissions with and without a Filter Attachment.

Fused filament fabrication three-dimensional (3D) printers have been shown to emit ultrafine particles (UFPs) and volatile organic compounds (VOCs). Previous studies have quantified bulk 3D printer particle and VOC emission rates, as well as described particle chemical composition via ex situ analysis. Here, we present size-resolved aerosol composition measurements from in situ aerosol mass spectrometry and ex situ transmission electron microscopy (TEM). Particles were sampled for in situ analysis during acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) 3D printing activities and ex situ analysis during ABS printing. We examined the effect of a high-efficiency particulate air filter attachment on ABS emissions and particle chemical composition and demonstrate that filtration was effective in preventing UFP emissions and that particles sampled during filtered prints did not have a high contribution (∼4% vs ∼10%) from aromatic ions in the mass spectrum. Ex situ analysis of particles collected during ABS printing was performed via TEM and electron energy loss spectroscopy, which indicated a high level of sp2 bonding type consistent with polymeric styrene. One 3D print with PLA resulted in an aerosol mass size distribution with a peak at ∼300 nm. Unfiltered ABS prints resulted in particle mass size distributions with peak diameters of ∼100 nm.

Edge Capping of 2D-MXene Sheets with Polyanionic Salts To Mitigate Oxidation in Aqueous Colloidal Suspensions.

MXenes have shown promise in myriad applications, such as energy storage, catalysis, EMI shielding, among many others. However, MXene oxidation in aqueous colloidal suspensions when stored in water at ambient conditions remains a challenge. It is now shown that by simply capping the edges of individual MXene flakes, Ti3 C2 Tz and V2 CTz , by polyanions such as polyphosphates, polysilicates or polyborates, it is possible to quite significantly reduce their propensity for oxidation even when held in aerated water for weeks. This breakthrough resulted from the realization that the edges of MXene sheets are positively charged. It is thus an example of selectively functionalizing the edges differently from the MXene sheet surfaces.

Elucidation of insulin assembly at acidic and neutral pH: Characterization of low molecular weight oligomers.

Deficiency in insulin secretion and function that characterize type 2 diabetes often requires administration of extraneous insulin, leading to injection-site amyloidosis. Insulin aggregation at neutral pH is not well understood. Although oligomer formation is believed to play an important role, insulin oligomers have not been fully characterized yet. Here, we elucidate similarities and differences between in vitro insulin aggregation at acidic and neutral pH for a range of insulin concentrations (2.5-100 µM) by using kinetic thioflavin T fluorescence, circular dichroism, atomic force and electron microscopy imaging. Importantly, we characterize the size distribution of insulin oligomers at different assembly stages by the application of covalent cross-linking and gel electrophoresis. Our results show that at the earliest assembly stage, oligomers comprise up to 40% and 70% of soluble insulin at acidic and neutral pH, respectively. While the highest oligomer order increases with insulin concentration at acidic pH, the opposite tendency is observed at neutral pH, where oligomers up to heptamers are formed in 10 µM insulin. These findings suggest that oligomers may be on- and off-pathway assemblies for insulin at acidic and neutral pH, respectively. Agitation, which is required to induce insulin aggregation at neutral pH, is shown to increase fibril formation rate and fibrillar mass both by an order of magnitude. Insulin incubated under agitated conditions at neutral pH rapidly aggregates into large micrometer-sized aggregates, which may be of physiological relevance and provides insight into injection-site amyloidosis and toxic pulmonary aggregates induced by administration of extraneous insulin.

Real-time observation of local strain effects on nonvolatile ferroelectric memory storage mechanisms.

We use in situ transmission electron microscopy to directly observe, at high temporal and spatial resolution, the interaction of ferroelectric domains and dislocation networks within BiFeO3 thin films. The experimental observations are compared with a phase field model constructed to simulate the dynamics of domains in the presence of dislocations and their resulting strain fields. We demonstrate that a global network of misfit dislocations at the film-substrate interface can act as nucleation sites and slow down domain propagation in the vicinity of the dislocations. Networks of individual threading dislocations emanating from the film-electrode interface play a more dramatic role in pinning domain motion. These dislocations may be responsible for the domain behavior in ferroelectric thin-film devices deviating from conventional Kolmogorov-Avrami-Ishibashi dynamics toward a Nucleation Limited Switching model.

Observation of self-assembled core-shell structures in epitaxially embedded TbErAs nanoparticles.

Self-assembled core-shell structured rare-earth nanoparticles (TbErAs) are observed in a III-V semiconductor host matrix (In0.53Ga0.47As) nominally lattice-matched to InP, grown via molecular beam epitaxy. Atom probe tomography demonstrates that the TbErAs nanoparticles have a core-shell structure, as seen both in the tomographic atom-by-atom reconstruction and concentration profiles. A simple thermodynamic model is created to determine when it is energetically favorable to have core-shell structures; the results strongly agree with the observations.

Complex dislocation loop networks as natural extensions of the sink efficiency of saturated grain boundaries in irradiated metals.

The development of radiation-tolerant structural materials is an essential element for the success of advanced nuclear energy concepts. A proven strategy to increase radiation resistance is to create microstructures with a high density of internal defect sinks, such as grain boundaries (GBs). However, as GBs absorb defects, they undergo internal transformations that limit their ability to capture defects indefinitely. Here, we show that, as the sink efficiency of GBs becomes exhausted with increasing irradiation dose, networks of irradiation loops form in the vicinity of saturated or near-saturated GB, maintaining and even increasing their capacity to continue absorbing defects. The formation of these networks fundamentally changes the driving force for defect absorption at GB, from "chemical" to "elastic." Using thermally-activated dislocation dynamics simulations, we show that these networks are consistent with experimental measurements of defect densities near GB. Our results point to these networks as a natural continuation of the GB once they exhaust their internal defect absorption capacity.

A (S)TEM gas cell holder with localized laser heating for in situ experiments.

The advent of aberration correction for transmission electron microscopy has transformed atomic resolution imaging into a nearly routine technique for structural analysis. Now an emerging frontier in electron microscopy is the development of in situ capabilities to observe reactions at atomic resolution in real time and within realistic environments. Here we present a new in situ gas cell holder that is designed for compatibility with a wide variety of sample type (i.e., dimpled 3-mm discs, standard mesh grids, various types of focused ion beam lamellae attached to half grids). Its capabilities include localized heating and precise control of the gas pressure and composition while simultaneously allowing atomic resolution imaging at ambient pressure. The results show that 0.25-nm lattice fringes are directly visible for nanoparticles imaged at ambient pressure with gas path lengths up to 20 µm. Additionally, we quantitatively demonstrate that while the attainable contrast and resolution decrease with increasing pressure and gas path length, resolutions better than 0.2 nm should be accessible at ambient pressure with gas path lengths less than the 15 µm utilized for these experiments.

A Denoising Autoencoder for Improved Kikuchi Pattern Quality and Indexing in Electron Backscatter Diffraction.

The rapid collection and indexing of electron diffraction patterns as produced via electron backscatter diffraction (EBSD) has enabled crystallographic orientation and structural determination, as well as additional property-determining strain and dislocation density information with increasing speed, resolution, and efficiency. Pattern indexing quality is reliant on the noise of the collected electron diffraction patterns, which is often convoluted by sample preparation and data collection parameters. EBSD acquisition is sensitive to many factors and thus can result in low confidence index (CI), poor image quality (IQ), and improper minimization of fit, which can result in noisy datasets and misrepresent the microstructure. In an attempt to enable both higher speed EBSD data collection and enable greater orientation fit accuracy with noisy datasets, an image denoising autoencoder was implemented to improve pattern quality. We show that EBSD data processed through the autoencoder results in a higher CI, IQ, and a more accurate degree of fit. In addition, using denoised datasets in HR-EBSD cross correlative strain analysis can result in reduced phantom strain from erroneous calculations due to the increased indexing accuracy and improved correspondence between collected and simulated patterns.

High-Resolution Electron Diffraction of Hydrated Protein Crystals at Room Temperature.

Structural characterization is crucial to understanding protein function. Compared with X-ray diffraction methods, electron crystallography can be performed on nanometer-sized crystals and can provide additional information from the resulting Coulomb potential map. Whereas electron crystallography has successfully resolved three-dimensional structures of vitrified protein crystals, its widespread use as a structural biology tool has been limited. One main reason is the fragility of such crystals. Protein crystals can be easily damaged by mechanical stress, change in temperature, or buffer conditions as well as by electron irradiation. This work demonstrates a methodology to preserve these nanocrystals in their natural environment at room temperature for electron diffraction experiments as an alternative to existing cryogenic techniques. Lysozyme crystals in their crystallization solution are hermetically sealed via graphene-coated grids, and their radiation damage is minimized by employing a low-dose data collection strategy in combination with a hybrid-pixel direct electron detector. Diffraction patterns with reflections of up to 3 Å are obtained and successfully indexed using a template-matching algorithm. These results demonstrate the feasibility of in situ protein electron diffraction. The method described will also be applicable to structural studies of hydrated nanocrystals important in many research and technological developments.

Microstructural changes in CdSe-coated ZnO nanowires evaluated by in situ annealing in transmission electron microscopy and x-ray diffraction.

We report on the crystallite growth and phase change of electrodeposited CdSe coatings on ZnO nanowires during annealing. Both in situ transmission electron microscopy (TEM) and x-ray diffraction (XRD) reveal that the nanocrystal size increases from ∼3 to ∼10 nm upon annealing at 350 °C for 1 h and then to more than 30 nm during another 1 h at 400 °C, exhibiting two distinct growth regimes. Nanocrystal growth occurs together with a structural change from zinc blende to wurtzite. The structural transition begins at 350 °C, which results in the formation of stacking faults. Increased crystallite size, comparable to the coating thickness, can improve charge separation in extremely thin absorber solar cells. We demonstrate a nearly two-fold improvement in power conversion efficiency upon annealing.

Termination-Property Coupling via Reversible Oxygen Functionalization of MXenes.

MXenes are a growing family of 2D transition-metal carbides and nitrides, which display excellent performance in myriad of applications. Theoretical calculations suggest that manipulation of the MXene surface termination (such as =O or -F) could strongly alter their functional properties; however, experimental control of the MXene surface termination is still in the developmental stage. Here, we demonstrate that annealing MXenes in an Ar + O2 low-power plasma results in increased =O functionalization with minimal formation of secondary phases. We apply this method to two MXenes, Ti2CT x and Mo2TiC2T x (T x represents the mixed surface termination), and show that in both cases, the increased =O content increases the electrical resistance and decreases the surface transition-metal's electron count. For Mo2TiC2O x , we show that the O content can be reversibly altered through successive vacuum and plasma annealing. This work provides an effective way to tune MXene surface functionalization, which may unlock exciting surface-dependent properties.

Implications of Microstructure in Helium-Implanted Nanocrystalline Metals.

Helium bubbles are known to form in nuclear reactor structural components when displacement damage occurs in conjunction with helium exposure and/or transmutation. If left unchecked, bubble production can cause swelling, blistering, and embrittlement, all of which substantially degrade materials and-moreover-diminish mechanical properties. On the mission to produce more robust materials, nanocrystalline (NC) metals show great potential and are postulated to exhibit superior radiation resistance due to their high defect and particle sink densities; however, much is still unknown about the mechanisms of defect evolution in these systems under extreme conditions. Here, the performances of NC nickel (Ni) and iron (Fe) are investigated under helium bombardment via transmission electron microscopy (TEM). Bubble density statistics are measured as a function of grain size in specimens implanted under similar conditions. While the overall trends revealed an increase in bubble density up to saturation in both samples, bubble density in Fe was over 300% greater than in Ni. To interrogate the kinetics of helium diffusion and trapping, a rate theory model is developed that substantiates that helium is more readily captured within grains in helium-vacancy complexes in NC Fe, whereas helium is more prone to traversing the grain matrices and migrating to GBs in NC Ni. Our results suggest that (1) grain boundaries can affect bubble swelling in grain matrices significantly and can have a dominant effect over crystal structure, and (2) an NC-Ni-based material can yield superior resistance to irradiation-induced bubble growth compared to an NC-Fe-based material and exhibits high potential for use in extreme environments where swelling due to He bubble formation is of significant concern.

RapidEELS: machine learning for denoising and classification in rapid acquisition electron energy loss spectroscopy.

Recent advances in detectors for imaging and spectroscopy have afforded in situ, rapid acquisition of hyperspectral data. While electron energy loss spectroscopy (EELS) data acquisition speeds with electron counting are regularly reaching 400 frames per second with near-zero read noise, signal to noise ratio (SNR) remains a challenge owing to fundamental counting statistics. In order to advance understanding of transient materials phenomena during rapid acquisition EELS, trustworthy analysis of noisy spectra must be demonstrated. In this study, we applied machine learning techniques to denoise high frame rate spectra, benchmarking with slower frame rate "ground truths". The results provide a foundation for reliable use of low SNR data acquired in rapid, in-situ spectroscopy experiments. Such a tool-set is a first step toward both automation in microscopy as well as use of these methods to interrogate otherwise poorly understood transformations.

A systematic review of preclinical in vivo testing of 3D printed porous Ti6Al4V for orthopedic applications, part I: Animal models and bone ingrowth outcome measures.

For Ti6Al4V orthopedic and spinal implants, osseointegration is often achieved using complex porous geometries created via additive manufacturing (AM). While AM porous titanium (pTi) has shown clinical success, concerns regarding metallic implants have spurred interest in alternative AM biomaterials for osseointegration. Insights regarding the evaluation of these new materials may be supported by better understanding the role of preclinical testing for AM pTi. We therefore asked: (a) What animal models have been most commonly used to evaluate AM porous Ti6Al4V for orthopedic bone ingrowth; (b) What were the primary reported quantitative outcome measures for these models; and (c) What were the bone ingrowth outcomes associated with the most frequently used models? We performed a systematic literature search and identified 58 articles meeting our inclusion criteria. We found that AM pTi was evaluated most often using rabbit and sheep femoral condyle defect (FCD) models. Additional ingrowth models including transcortical and segmental defects, spinal fusions, and calvarial defects were also used with various animals based on the study goals. Quantitative outcome measures determined via histomorphometry including ''bone ingrowth'' (range: 3.92-53.4% for rabbit/sheep FCD) and bone-implant contact (range: 9.9-59.7% for rabbit/sheep FCD) were the most common. Studies also used 3D imaging to report outcomes such as bone volume fraction (BV/TV, range: 4.4-61.1% for rabbit/sheep FCD), and push-out testing for outcomes such as maximum removal force (range: 46.6-3092 N for rabbit/sheep FCD). Though there were many commonalities among the study methods, we also found significant heterogeneity in the outcome terms and definitions. The considerable diversity in testing and reporting may no longer be necessary considering the reported success of AM pTi across all model types and the ample literature supporting the rabbit and sheep as suitable small and large animal models, respectively. Ultimately, more standardized animal models and reporting of bone ingrowth for porous AM materials will be useful for future studies.

Ion irradiation induced phase transformation in gold nanocrystalline films.

Gold is a noble metal typically stable as a solid in a face-centered cubic (FCC) structure under ambient conditions; however, under particular circumstances aberrant allotropes have been synthesized. In this work, we document the phase transformation of 25 nm thick nanocrystalline (NC) free-standing gold thin-film via in situ ion irradiation studied using atomic-resolution transmission electron microscopy (TEM). Utilizing precession electron diffraction (PED) techniques, crystallographic orientation and the radiation-induced relative strains were measured and furthermore used to determine that a combination of surface and radiation-induced strains lead to an FCC to hexagonal close packed (HCP) crystallographic phase transformation upon a 10 dpa radiation dose of Au4+ ions. Contrary to previous studies, HCP phase in nanostructures of gold was stabilized and did not transform back to FCC due to a combination of size effects and defects imparted by damage cascades.

Evidence of a magnetic transition in atomically thin Cr2TiC2Tx MXene.

Two-dimensional (2D) transition metal carbides and nitrides known as MXenes have shown attractive functionalities such as high electronic conductivity, a wide range of optical properties, versatile transition metal and surface chemistry, and solution processability. Although extensively studied computationally, the magnetic properties of this large family of 2D materials await experimental exploration. 2D magnetic materials have recently attracted significant interest as model systems to understand low-dimensional magnetism and for potential spintronic applications. Here, we report on synthesis of Cr2TiC2Tx MXene and a detailed study of its magnetic as well as electronic properties. Using a combination of magnetometry, synchrotron X-ray linear dichroism, and field- and angular-dependent magnetoresistance measurements, we find clear evidence of a magnetic transition in Cr2TiC2Tx at approximately 30 K, which is not present in its bulk layered carbide counterpart (Cr2TiAlC2 MAX phase). This work presents the first experimental evidence of a magnetic transition in a MXene material and provides an exciting opportunity to explore magnetism in this large family of 2D materials.