Comparison of laboratory and field testing performance evaluations of siloxane-polyurethane fouling-release marine coatings.

A series of eight novel siloxane-polyurethane fouling-release (FR) coatings were assessed for their FR performance in both the laboratory and in the field. Laboratory analysis included adhesion assessments of bacteria, microalgae, macroalgal spores, adult barnacles and pseudobarnacles using high-throughput screening techniques, while field evaluations were conducted in accordance with standardized testing methods at three different ocean testing sites over the course of six-months exposure. The data collected were subjected to statistical analysis in order to identify potential correlations. In general, there was good agreement between the laboratory screening assays and the field assessments, with both regimes clearly distinguishing the siloxane-polyurethane compositions comprising monofunctional poly(dimethyl siloxane) (PDMS) (m-PDMS) as possessing superior, broad-spectrum FR properties compared to those prepared with difunctional PDMS (d-PDMS). Of the seven laboratory screening techniques, the Cellulophaga lytica biofilm retraction and reattached barnacle (Amphibalanus amphitrite) adhesion assays were shown to be the most predictive of broad-spectrum field performance.

Tea stains-inspired initiator primer for surface grafting of antifouling and antimicrobial polymer brush coatings.

Inspired by tea stains, plant polyphenolic tannic acid (TA) was beneficially employed as the primer anchor for functional polymer brushes. The brominated TA (TABr) initiator primer was synthesized by partial modification of TA with alkyl bromide functionalities. TABr with trihydroxyphenyl moieties can readily anchor on a wide range of substrates, including metal, metal oxide, polymer, glass, and silicon. Concomitantly, the alkyl bromide terminals serve as initiation sites for atom transfer radical polymerization (ATRP). Cationic [2-(methacryloyloxy)ethyl]trimethylammonium chloride (META) and zwitterionic 2-methacryloyloxyethyl phosphorylcholine (MPC) and N-(3-sulfopropyl)-N-(methacryloxyethyl)-N,N-dimethylammonium betaine (SBMA) were graft-polymerized from the TABr-anchored stainless steel (SS) surface. The cationic polymer brushes on the modified surfaces are bactericidal, while the zwitterionic coatings exhibit resistance against bacterial adhesion. In addition, microalgal attachment (microfouling) and barnacle cyprid settlement (macrofouling) on the functional polymer-grafted surfaces were significantly reduced, in comparison to the pristine SS surface. Thus, the bifunctional TABr initiator primer provides a unique surface anchor for the preparation of functional polymer brushes for inhibiting both microfouling and macrofouling.

Multilayers of fluorinated amphiphilic polyions for marine fouling prevention.

Sequential layer-by-layer (LbL) deposition of polyelectrolytes followed by chemical cross-linking was investigated as a method to fabricate functional amphiphilic surfaces for marine biofouling prevention applications. A novel polyanion, grafted with amphiphilic perfluoroalkyl polyethylene glycol (fPEG) side chains, was synthesized and subsequently used to introduce amphiphilic character to the LbL film. The structure of the polyanion was confirmed by FTIR and NMR. Amphiphilicity of the film assembly was demonstrated by both water and hexadecane static contact angles. XPS studies of the cross-linked and annealed amphiphilic LbL films revealed the increased concentration of fPEG content at the film interface. In antifouling assays, the amphiphilic LbL films effectively prevented the adhesion of the marine bacterium Pseudomonas (NCIMB 2021).

Barnacle cement as surface anchor for "clicking" of antifouling and antimicrobial polymer brushes on stainless steel.

Barnacle cement (BC) was utilized 'beneficially' as a surface anchor on stainless steel (SS) for coupling of functional polymer brushes via "click" reactions in both "grafting-to" and "grafting-from" processes. Ethylene sulfide (ES), propargyl carbonylimidazole (PPC) and azidoethyl carbonylimidazole (AEC) reacted with amine and/or hydroxyl groups in BC to introduce the corresponding thiol, alkyne, and azide groups on SS surfaces (SS-thiol, SS-alkyne, and SS-azide, respectively). Antifouling zwitterionic SS-PMPC surface was prepared by thiol-ene photopolymerization of 2-methacryloyloxyethyl phosphorylcholine (MPC) from the SS-thiol surface. Protein-resistant SS-PPEGMA and protein-adsorbing SS-PPFS surfaces were prepared by coupling of the respective azide-functionalized poly(poly(ethylene glycol)methyl ether methacrylate) (azido-PPEGMA) and poly(2,3,4,5,6-pentafluorostyrene) (azido-PPFS) polymer brushes in azide-alkyne "click" reaction. Antifouling alkyne-functionalized poly(N-hydroxyethyl acrylamide) (alkynyl-PHEAA) and antibacterial alkyne-functionalized poly(2-(methacryloyloxy)ethyl trimethylammonium chloride) (alkynyl-PMETA) polymer brushes were clicked on the SS-azide surface. Adsorption of bovine serum albumin and bacteria fouling of Gram-negative Escherichia coli ( E. coli ) and Gram-positive Staphylococcus epidermidis ( S. epidermidis ) were investigated on the polymer-functionalized SS surfaces. The versatile bioanchor and functional polymer brush coatings are stable in an abiotic aqueous environment for over a month.

A novel geometry for a laboratory-based larval settlement assay.

A novel configuration, consisting of two apposing surfaces bounding a vertical water column, is presented and evaluated for settlement assays using cyprids of Balanus amphitrite. Assays were conducted on planar surfaces, ranging from hydrophobic polystyrene to hydrophilic glass and including CH(3)- and NH(3) (+)-terminated self-assembled monolayers (SAMs). Identical apposing surfaces generated settlement rates comparable to those obtained in prior studies, while a choice assay yielded consistent results, with individual replicates each indicating the preferred surface for settlement. As gravity favours contact with the lower apposing surface, cyprids trapped at the air/water interface settled on or around the perimeter where the water column meets the lower substratum. These cyprids are capable of selecting a settlement location and are thus not lost to the assay. The assay geometry lends itself to assessing cyprid exploration and settlement on planar surfaces with chemical patterning, including relief microstructures, without using a confining material or requiring the coating of a three-dimensional well.

Layer-by-layer click deposition of functional polymer coatings for combating marine biofouling.

"Click" chemistry-enabled layer-by-layer (LBL) deposition of multilayer functional polymer coatings provides an alternative approach to combating biofouling. Fouling-resistant azido-functionalized poly(ethylene glycol) methyl ether methacrylate-based polymer chains (azido-poly(PEGMA)) and antimicrobial alkynyl-functionalized 2-(methacryloyloxy)ethyl trimethyl ammonium chloride-based polymer chains (alkynyl-poly(META)) were click-assembled layer-by-layer via alkyne-azide 1,3-dipolar cycloaddition. The polymer multilayer coatings are resistant to bacterial adhesion and are bactericidal to marine Gram-negative Pseudomonas sp. NCIMB 2021 bacteria. Settlement of barnacle ( Amphibalanus (= Balanus ) amphitrite ) cyprids is greatly reduced on the multilayer polymer-functionalized substrates. As the number of the polymer layers increases, efficacy against bacterial fouling and settlement of barnacle cyprids increases. The LBL-functionalized surfaces exhibit low toxicity toward the barnacle cyprids and are stable upon prolonged exposure to seawater. LBL click deposition is thus an effective and potentially environmentally benign way to prepare antifouling coatings.

Inhibition of barnacle cyprid settlement using low frequency and intensity ultrasound.

Low frequency, low intensity ultrasound was demonstrated as an effective inhibitor of barnacle cyprid settlement. When the same substratum vibration amplitude (10.05 nm) and acoustic pressure (5 kPa) were applied, ultrasound at a frequency of 23 kHz significantly reduced cyprid settlement. The mechanism appeared to differ from the ultrasonic cavitation induced inhibition previously reported as no increased mortality was observed, and no change in the exploratory behaviour of cyprids was observed when they were exposed to this continuous ultrasonic irradiation regime. The application of ultrasound treatment in an intermittent mode of '5 min on and 20 min off' at 20-25 kHz and at the low intensity of 5 kPa produced the same effect as the continuous application of 23 kHz. This energy efficient approach to the use of low frequency, low intensity ultrasound may present a promising and efficient strategy regarding irradiation treatment for antifouling applications.

Functional polymer brushes via surface-initiated atom transfer radical graft polymerization for combating marine biofouling.

Dense and uniform polymer brush coatings were developed to combat marine biofouling. Nonionic hydrophilic, nonionic hydrophobic, cationic, anionic and zwitterionic polymer brush coatings were synthesized via surface-initiated atom transfer radical polymerization (SI-ATRP) of 2-hydroxyethyl methacrylate, 2,3,4,5,6-pentafluorostyrene, 2-(methacryloyloxy)ethyl trimethylammonium chloride, 4-styrenesulfonic acid sodium and N,N'-dimethyl-(methylmethacryloyl ethyl) ammonium propanesulfonate, respectively. The functionalized surfaces had different efficacies in preventing adsorption of bovine serum albumin (BSA), adhesion of the Gram-negative bacterium Pseudomonas sp. NCIMB 2021 and the Gram-positive Staphylococcus aureus, and settlement of cyprids of the barnacle Amphibalanus amphitrite (=Balanus amphitrite). The nonionic hydrophilic, anionic and zwitterionic polymer brushes resisted BSA adsorption during a 2 h exposure period. The nonionic hydrophilic, cationic and zwitterionic brushes exhibited resistance to bacterial fouling (24 h exposure) and cyprid settlement (24 and 48 h incubation). The hydrophobic brushes moderately reduced protein adsorption, and bacteria and cyprid settlement. The anionic brushes were least effective in preventing attachment of bacteria and barnacle cyprids. Thus, the best approach to combat biofouling involves a combination of nonionic hydrophilic and zwitterionic polymer brush coatings on material surfaces.

A comparative investigation of toxicity of three polymer nanoparticles on acorn barnacle (Amphibalanus amphitrite).

Pollution from plastic waste is increasingly prevalent in the environment and beginning to generate significant adverse impact on the health of living organisms. In this study, we investigate the toxicity of polymer nanoparticles exposed to Acorn Barnacle (Amphibalanus amphitrite) nauplii, as an animal model. Highly stable aqueous dispersion of luminescent nanoparticles from three common polymers: polymethylmethacrylate (PMMA), polystyrene (PS), and polyvinylchloride (PVC), were prepared via nanoprecipitation and fully characterised. Exposure studies of these polymer particles to freshly spawned barnacle nauplii were performed within a concentration range from 1 to 25 mg/L under laboratory-controlled conditions. The exposure to PMMA and PS nanoparticles did not show detrimental toxicity and did not cause sufficient mortality to compute a LC50 value. However, PVC nanoparticles were significantly toxic with a mortality rate of up to 99% at 25 mg/L, and the calculated LC50 value for PVC nanoparticles was 7.66 ± 0.03 mg/L, 95% CI. Interestingly, PVC nanoparticle aggregates were observed to adhere to the naupliar carapace and appendages at higher concentrations and could not be easily removed by washings. To explore the possibility of chemical toxicity of polymer nanoparticles, analysis of the polymer powders which was used to prepare the nanoparticles was conducted. The presence of low molecular weight oligomers such as dimers, trimers and tetramers were observed in all polymer samples. The chemical nature and concentration of such compounds are likely responsible for the observed toxicity to the barnacle nauplii. Overall, our study shows that care should be exercised in generalising the findings of exposure studies performed using one type of plastic particles, as the use of different plastic particles may elicit different responses inside a living organism.

On the mechanism of marine fouling-prevention performance of oil-containing silicone elastomers.

For many decades, silicone elastomers with oil incorporated have served as fouling-release coating for marine applications. In a comprehensive study involving a series of laboratory-based marine fouling assays and extensive global field studies of up to 2-year duration, we compare polydimethylsiloxane (PDMS) coatings of the same composition loaded with oil via two different methods. One method used a traditional, one-pot pre-cure oil addition approach (o-PDMS) and another method used a newer post-cure infusion approach (i-PDMS). The latter displays a substantial improvement in biofouling prevention performance that exceeds established commercial silicone-based fouling-release coating standards. We interpret the differences in performance between one-pot and infused PDMS by developing a mechanistic model based on the Flory-Rehner theory of swollen polymer networks. Using this model, we propose that the chemical potential of the incorporated oil is a key consideration for the design of future fouling-release coatings, as the improved performance is driven by the formation and stabilization of an anti-adhesion oil overlayer on the polymer surface.

Sewage sludge ash-based mortar as construction material: Mechanical studies, macrofouling, and marine toxicity.

Incinerated sewage sludge ash is tested here as a cement and aggregate substitute in mortar blocks. It can be used at various percentages to reduce the overall cost of production and promote ash recycling. The compressive strength of the cast blocks was tested at 28 days to determine the optimal combination of ball milled ash (replacing cement) and sewage sludge ash (replacing sand). This was compared with a control block made of cement and sand only. The cast blocks with the optimal ash formulation were tested for their flexural strength and other properties such as surface functional groups, constituent phases and porosity. The control and ash mortars exhibited similar properties. A potential application of these blocks is to use them as part of seawalls. These blocks were thus suspended in the sea for 6 months. Marine organism attachment was observed over time in both control and ash mortar blocks. There was no significant difference between the mortars after 6 months. The mortar blocks were also subjected to leaching tests (NEN-7345). The leachates did not exhibit toxicity to microalgae. In contrast, mild toxicity was observed in the sea urchin embryo development assay. Overall, the study suggests that sewage sludge ash is a potential material to be used for seawall construction as it has the desirable mechanical properties. However, there remain some residual marine toxicity concerns that need to be further addressed.

Biomimetic anchors for antifouling and antibacterial polymer brushes on stainless steel.

Barnacle cement (BC) was beneficially applied on stainless steel (SS) to serve as the initiator anchor for surface-initiated polymerization. The amine and hydroxyl moieties of barnacle cement reacted with 2-bromoisobutyryl bromide to provide the alkyl halide initiator for the surface-initiated atom transfer radical polymerization (ATRP) of 2-hydroxyethyl methacrylate (HEMA). The hydroxyl groups of HEMA polymer (PHEMA) were then converted to carboxyl groups for coupling of chitosan (CS) to impart the SS surface with both antifouling and antibacterial properties. The surface-functionalized SS reduced bovine serum albumin adsorption, bacterial adhesion, and exhibited antibacterial efficacy against Escherichia coli (E. coli). The effectiveness of barnacle cement as an initiator anchor was compared to that of dopamine, a marine mussel inspired biomimetic anchor previously used in surface-initiated polymerization. The results indicate that the barnacle cement is a stable and effective anchor for functional surface coatings and polymer brushes.

Effect of ultrasound on cyprids and juvenile barnacles.

Settlement inhibition of barnacle (Amphibalanus amphitrite) cypris larvae resulting from exposure to ultrasound was measured at three frequencies (23, 63, and 102 kHz), applied at three acoustic pressure levels (9, 15, and 22 kPa) for exposure times of 30, 150, and 300 s. The lowest settlement was observed for 23 kHz, which also induced the highest cyprid mortality. Cyprid settlement following exposure to 23 kHz at 22 kPa for 30 s was reduced by a factor of two. Observing surface exploration by the cyprids revealed an altered behaviour following exposure to ultrasound: step length was increased, while step duration, walking pace, and the fraction of cyprids exploring the surface were significantly reduced with respect to control cyprids. The basal area of juvenile barnacles, metamorphosed from ultrasound-treated cyprids was initially smaller than unexposed individuals, but normalised over two weeks' growth. Thus, ultrasound exposure effectively reduced cyprid settlement, yet metamorphosed barnacles grew normally.

Ascidians collected during the 2013 Singapore Strait International Marine Biodiversity Workshop.

During the 2013 Singapore Strait International Marine Biodiversity Workshop, hundreds of ascidians were collected along with numerous other marine phyla. Collections were made intertidally as well as subtidally by snorkel, SCUBA, trawling and dredging. While many ascidian specimens remain unidentified, 14 aplousobranchs, nine phlebobranchs and 17 stolidobranchs have been identified; a surprising 50% of these comprise 20 new records for Singapore. An additional new record of the phlebobranch Perophora namei collected from the same area in 2014 and 2015 is included here. Of the 21 new records, Aplidium cf. grisiatum, Distaplia regina, Euherdmania cf. digitata, Cnemidocarpa irene, Monandrocarpa monotestis and Polyandrocarpa rollandi are also first records for the entire South China Sea region.

Spirobranchus bakau sp. nov. from Singapore: yet another species of S. kraussii-complex (Polychaeta: Serpulidae).

The intertidal serpulid polychaete Spirobranchus kraussii was originally described from South Africa and has since been reported in numerous sub (tropical) localities around the world. Recently, however, S. kraussii was uncovered as a complex of morphologically similar and geographically restricted species, raising the need to revise S. cf. kraussii populations. We formally describe S. cf. kraussii from Singapore mangroves as Spirobranchus bakau sp. nov. based on morphological and molecular data. Despite their morphological similarities, Maximum Likelihood and Bayesian Inference analyses of 18S and Cyt b DNA sequence data confirm that S. bakau sp. nov. is genetically distinct from S. kraussii and other known species in the complex. Both analyses recovered S. bakau sp. nov. as part of a strongly supported clade (96% bootstrap, 1 posterior probability), comprising S. sinuspersicus, S. kraussii and S. cf. kraussii from Australia and Hawaii. Additionally, paratypes of S. kraussii var. manilensis, described from Manila Bay in the Philippines, were examined and elevated to the full species S. manilensis. Finally, we tested the hypothesis that fertilisation and embryonic development of S. bakau sp. nov. can occur under the wide range of salinities (19.630.9 psu) and temperatures (2531C) reported in the Johor Strait. Fertilisation success of ≥70% was achieved across a temperature range of 2532C and a salinity range of 2032 psu. Embryonic development, however, had a narrower salinity tolerance range of 2732 psu. Clarifying the taxonomic status of S. cf. kraussii populations reported from localities elsewhere in Singapore and Southeast Asia will be useful in establishing the geographical distribution of S. bakau sp. nov. and other members of the S. kraussii-complex.

Incinerated Sewage Sludge Bottom Ash- Chemical processing, Leaching patterns and Toxicity testing.

Sewage sludge bottom ash, which is the major fraction obtained from the incineration of sewage sludge was treated with various organic and inorganic acids for heavy metal removal, along with a comparative phosphate treatment for heavy metal fixation. Malonic acid, an organic acid, was found to remove heavy metals better as compared to nitric acid, a strong inorganic acid. The acid treated samples were further examined for heavy metal leaching, followed by marine toxicity/abnormality testing of the leachates, where acid treated and phosphate treated ash leachate displayed higher (with malonic acid proving to be most toxic) and similar toxicity profiles as compared to raw ash leachate respectively. Raw ash was tested for its leaching patterns at different liquid/solid ratios(L/S = 5 and 10), salinities and time points (24, 48 and 72 h), where the leaching was found to saturate at L/S = 5 and at 24 h with varied salinity effecting the leaching insignificantly. When raw ash was benchmarked against concrete sand for marine toxicity, a material commonly used for land reclamation, acute toxicity patterns were found to be mostly similar except in case of the sea urchin embryonic assay, where toxicity was detected, indicating the sensitivity of the assay to residual levels of heavy metals. The raw ash was also tested against human cell lines where it displayed size and dose-dependent toxicity. To enable the use of ash for environment applications such as coastal reclamation, appropriate treatments are required to minimize leaching of potential harmful contaminants and this study demonstrates the importance of post-treatment of ash on its subsequent toxicity to organisms.

Natural antifoulants from the marine cyanobacterium Lyngbya majuscula.

Filamentous benthic marine cyanobacteria are a prolific source of structurally unique bioactive secondary metabolites. A total of 12 secondary metabolites, belonging to the mixed polyketide-polypeptide structural class, were isolated from the marine cyanobacterium, Lyngbya majuscula, and were tested to determine if they showed activity against barnacle larval settlement. The assays revealed four compounds, dolastatin 16, hantupeptin C, majusculamide A, and isomalyngamide A, that showed moderate to potent anti-larval settlement activities, with EC(50) values ranging from 0.003 to 10.6 microg ml(-1). In addition, field testing conducted over a period of 28 days (using the modified Phytagel method) based on the cyanobacterial compound, dolastatin 16, showed significantly reduced barnacle settlement as compared to controls at all the concentrations tested. The results of this study highlight the importance of marine cyanobacteria as an underexplored source of potential environmentally friendly antifoulants.

Removal of larvae of two marine invasive bivalves, Mytilopsis sallei (Récluz, 1849) and Mytella strigata (Hanley, 1843), by water treatment processes.

The uptake and discharge of bivalve larvae through ballast water operations is a highly viable mechanism for transfer of shellfish. In this paper, we investigate the effects of common water treatment processes on the planktotrophic larvae of the two invasive species of shellfish, Mytilopsis sallei and Mytella strigata. The study found that common water treatment processes used in many ballast water treatment systems were effective for the removal of bivalve larvae, although later stages of larval forms required more effort to remove.

Marine biofouling field tests, settlement assay and footprint micromorphology of cyprid larvae of Balanus amphitrite on model surfaces.

Atomic force microscopy (AFM), laboratory settlement assays and field tests were used to correlate cyprid footprint (FP) morphology with the behaviour of cyprids on different substrata. AFM imaging under laboratory conditions revealed more porous and larger FPs on glass exposing a CH3-surface than on aminosilane functionalised (NH2-) surfaces. The secreted FP volume was found to be similar on both substrata (2.1-2.6 microm(3)). Laboratory settlement assays and marine field tests were performed on three substrata, viz. untreated clean glass, NH2-glass, and CH3-glass. The results distinguished settlement preferences for NH2-glass and untreated glass over CH3-terminated surfaces, suggesting that cyprids favour settling on hydrophilic over hydrophobic surfaces. On combining observations from different length scales, it is speculated that the confined FP size on NH2-glass may induce a higher concentration of the settlement inducing protein complex. Settlement may be further facilitated by a stronger adherence of FP adhesives to the NH2-surface via Coulombic interactions.

Evaluation of sewage sludge incineration ash as a potential land reclamation material.

This study evaluated the potential of utilising sewage sludge incineration ash as a land reclamation material. Toxicity assessment of the leachate of the ash was carried out for both terrestrial and marine organisms. Both the fruit fly Drosophila melanogaster and barnacle Amphibalanus amphitrite showed that both bottom and fly ash leached at liquid-to-solid (L/S) ratio 5 did not substantially affect viabilities. The leachate carried out at L/S 10 was compared to the European Waste Acceptance Criteria and the sewage sludge ashes could be classified as non-hazardous waste. The geotechnical properties of the sewage sludge ash were studied and compared to sand, a conventional land reclamation material, for further evaluation of its potential as a land reclamation material. It was found from direct shear test that both bottom and fly ashes displayed similar and comparable shear strength to that of typical compacted sandy soil based on the range of internal friction angle obtained. However, the consolidation profile of bottom ash was significantly different from sand, while that of fly ash was more similar to sand. Our study showed that the sewage sludge ash has the potential to be used as a land reclamation material.