Long-term survivorship of an exchangeable-neck hip prosthesis with a Ti-alloy/Ti-alloy neck-stem junction.

INTRODUCTION: Breakage of exchangeable-neck (EN) and adverse local tissue reactions (ALTRs) to neck-stem junction (NSJ) damage products are responsible for increasing the revision rate of EN hip prostheses. We investigated the survivorship of an EN hip prosthesis including a NSJ with both components made of titanium alloy (Ti-alloy/Ti-alloy) to assess whether, and to what extent, EN breakage and NSJ damage affected implant survivorship. MATERIALS AND METHODS: Using data from a hip replacement registry, we determined survivorship of 2857 EN prostheses. Long-offset configurations of head and EN were implanted in heavy (> 90 kg) patients only in 23 hips. We investigated under which conditions EN breakages or ALTRs occurred. We also measured titanium (Ti) and vanadium (V) blood concentrations in 24 patients with a unilateral well-working prosthesis. RESULTS: The 17-year survival rates for any reason and aseptic loosening of any component were 88.9% (95%CI 87.5-90.1; 857 hips at risk) and 96.9% (95%CI 96.0-97.6), respectively. There were two cases of EN breakage and one case of ALTR (metallosis), due to rim-neck impingement, out of 276 revisions. After an average period of 9.8 years (range 7.8-12.8 years), the maximum Ti and V blood concentrations in patients with a well-working prosthesis were 5.0 µg/l and 0.16 µg/l, respectively. CONCLUSION: The present incidence of EN breakage or ALTR is lower than those reported in other studies evaluating EN hip prosthesis survivorship. This study suggests that (i) the risk of EN breakage is reduced by limiting the use of long-offset configurations in heavy patients and (ii) Ti-alloy/Ti-alloy NSJ damage products do not promote ALTR nor significantly alter the rate of implant loosening. Since design decisions and implant configuration determine the NSJ strength, the NSJ strength in working conditions must be thoroughly investigated to proper define the clinical indications for any EN design.

Ischemia-Modified Albumin Expression: Is there a Difference between Male and Female Subjects?

BACKGROUND: Ischemia-modified albumin (IMA) derives from naive albumin, modified in the binding region of bivalent ions, as cobalt and iron. The cobalt, released from some types of hip prosthesis seems to be metabolized differently in males and females but the iron ion is more prevalent than cobalt and is detectable in the healthy population. Our aim was to verify if there are any gender- and age-related differences in IMA concentrations and if IMA correlates with cobalt and iron-related proteins. METHODS: IMA, albumin, iron, ferritin, transferrin, and cobalt were measured in 50 men and 50 women divided into two age/fertility-homogeneous groups. RESULTS: Men < 45-years-old showed a statistically significant lower IMA concentration than men ≥ 45 and fertile and menopausal women. Considering all the population studied, IMA does not seem to be correlated with age and is distributed differently by gender; also, Co distribution was different between males and females. CONCLUSIONS: IMA did not correlate with cobalt, iron, ferritin, and transferrin in any group, except for fertile women where IMA presented a statistically significant correlation with serum iron values. Minor expression of IMA in young males together with the results obtained on serum iron in fertile females, could explain the higher accumulation of circulating Co in women compared to men and their different cobalt metabolism.

Component positioning and ceramic damage in cementless ceramic-on-ceramic total hip arthroplasty.

BACKGROUND: In ceramic-on-ceramic (CoC) total hip arthroplasty (THA), component positioning demonstrated to influence the bearing damage: however the connection between angles and clinical outcomes at long-term follow-ups is currently lacking. Aims of this study were: the computer tomography (CT) assessment of component positioning in CoC THAs; the correlation analysis between positioning and ceramic damage; the identification of safe zones. METHODS: 91 consecutive post-operative CT scans including two types of CoC implants, with a mean follow-up of 12 ± 4.4 years, were evaluated. III generation (74.2%) and IV generation (25.8%) CoC surfaces were included. The angle measurements (cup abduction, anteversion, cup tilt, stem antetorsion, sacral slope) were automated using a CT-based software. The combined anteversion was assessed as well as the cup-neck position at -15°, 0°, 45° and 90° of flexion. Ceramic damage was diagnosed using synovial fluid analyses and radiological criteria. RESULTS: 63.7% of THAs was inside the cup abduction target 30°-45° and 68.1% was inside the cup anteversion target 5°-25°. 19 patients (20.9%) showed signs of ceramic damage. High cup abduction and high cup-neck 45° minimum angle (which stood for high abduction and extreme combined version) significantly correlated with ceramic damage. No demographical features apart III generation ceramic bearings influenced the results. No safe zones could be detected. CONCLUSIONS: In CoC THA, no safe zones can be described. However it is important to avoid cup inclination over 45° and a combination of steep cup and extreme combined version.

The influence of bearing surfaces on periprosthetic hip infections: analysis of thirty nine thousand, two hundred and six cementless total hip arthroplasties.

PURPOSE: Periprosthetic hip infection (PHI) is a devastating complication. The association between PHI and bearing surfaces as well as patient-related factors has been recently investigated, with contradictive outcomes. The dataset of Emilia-Romagna region Registry for Orthopaedic Prosthetic Implants (RIPO) has been assessed to investigate, if the bearing choice influenced the risk of septic loosening occurrence. METHODS: RIPO data about 39,206 cementless total hip arthroplasties (THA), collected since 2003, were analysed. Age, gender, BMI, diabetes and bearing surfaces were evaluated. The end point of the study was the revision of at least a single component due to sepsis. RESULTS: Adjusted and unadjusted survival rates showed that ceramic-on-ceramic (COC) implants had the lower incidence of PHIs, whereas metal-on-metal (MOM) THAs were significantly more prone to infection. In MOM cohort, stemmed implants were involved in 28 out of 30 cases. Among the demographical features and comorbid conditions, only diabetes statistically influenced the rate of sepsis. CONCLUSIONS: Bearing surfaces influenced the rate of PHI; in particular, stemmed MOM implants were at higher risk, probably due to metal debris consequent to taperosis. Despite the preliminary results, stemmed MOM THAs should be used with care, and diabetic patients should be warned about increased septic risks.

Cementless Total Hip Arthroplasty in Crowe III and IV Dysplasia: High Hip Center and Modular Necks.

BACKGROUND: Total hip arthroplasty (THA) in severe developmental dysplasia of the hip (DDH) is a challenging procedure. The most used techniques involve anatomic cup positioning, augmentation femoral osteotomy. However, anatomic cup positioning is not always feasible in severe DDH and osteotomy nonunion may ensue. The purpose of the study was to assess the survivorship, the hip score results, the radiological parameters (fixation, loosening, component position) of a large cohort of patients with Crowe III and IV DDH, treated with high hip center and modular necks THAs. METHODS: Eighty-four THAs in Crowe III and IV DDH were evaluated, achieving a final follow-up of 15.1 years. All the patients were treated with the same cementless implant (modular necks and ceramic-on-ceramic coupling) and the same approach (high cup placement with slight medialization). The patients were clinically evaluated (Harris Hip score and Merle d'Aubigne and Postel score). A radiographic evaluation was performed, analyzing the orientation of the cup. RESULTS: Eighty patients were available at the last follow-up. The clinical scores were good at the final follow-up. Two sciatic lesions occurred: one patient fully recovered. The overall survivorship was 90.5% at 15 years: only 2 cases of aseptic loosening were reported. The mean center of rotation height was 33 ± 8 mm and the medialization was 30 ± 5 mm. CONCLUSION: A high cup placement with slight medialization is a valid technique in DDH patients. A good restoration of the offset, ceramic-on-ceramic coupling and a porous socket may provide durable results, overcoming the effects of increasing joint reaction forces related to high cup placement.

Is Cross-Linked Polyethylene an Improvement Over Conventional Ultra-High Molecular Weight Polyethylene in Total Knee Arthroplasty?

BACKGROUND: Reducing polyethylene (PE) wear by increasing the cross-linking encouraged surgeons to hope for increased total knee arthroplasty (TKA) survival rates. Different methods of manufacturing cross-linked polyethylene (XLPE) were introduced, following promising in vitro results. Is there a measurable effect of cross-linking on TKA survival? METHODS: A registry study was conducted, focusing on fixed tibial inserts in primary TKA. Conventional PE represented 87% of the liners, 10% were cross-linked and 2% were antioxidant PE. Sixty-four percent of the liners were posterior-stabilized (PS). Survival of the different PE groups and survival of the main XLPE available were successively compared. We also looked for differences in the same brand implant groups with regard to PE type, as well as differences between cruciate retaining and PS knees. RESULTS: No differences were found when looking at survival for any cause or for aseptic loosening only (P = .96). When comparing the XLPE available, X3 was found to have a better survival than Prolong or Smith & Nephew XLPE (P = .036). When the same implants and X3 or conventional PE were used, no difference could reach a statistical significance. With Zimmer LPS Flex, Prolong XLPE was even associated with a lower survival compared with conventional PE. On Stryker implants, only the Cox regression model allowed highlighting a difference between X3 XLPE and conventional PE, only in PS knees. CONCLUSION: Increasing the cross-linking seems to only have a low effect, if any, on knee arthroplasty survival. Differences between brands could be found; the manufacturing process could play a role.

Short Stems Versus Conventional Stems in Cementless Total Hip Arthroplasty: A Long-Term Registry Study.

BACKGROUND: Short stems in total hip arthroplasty (THA) have recently gained increasing popularity, allowing mini-invasive exposures and bone-sparing approaches. However, long-term studies and recommendations for the routine use are not available. The aim of this report was to compare the survival rates and the reasons for revision of short stems versus conventional stems in cementless THAs, in a registry-based population. METHODS: The Registry of Prosthetic Orthopedic Implants (RIPO) was inquired about cementless THAs performed since 2000 to 2016. The stems were divided into short (<12 cm) and conventional ones, and then, classified according to the classification by Feyen and Shimmin: short stems with neck-retaining osteotomy (group A: 1684 hips), short stems with standard osteotomy (group B: 2727 THAs), and conventional stems (group C: 57,359 cases). Demographics, survivorships, and reasons for revision were investigated and compared. RESULTS: Short stems were preferentially implanted in younger patients and normal morphologies. Short and conventional stems showed comparable survival rates at long-term follow-up (>90% at 15 years). The rates of stem aseptic loosening, intraoperative fractures, and periprosthetic fractures were similar in the 3 groups. Group B had higher rates of revisions due to primary instability (early dislocations and impingement-related events; P < .05). Revisions due to pain were nonsignificantly higher in group B. CONCLUSION: Short stems are reliable implants at long-term follow-up. The comparison with conventional stems showed no additional risk of premature aseptic loosening and intraoperative and periprosthetic fractures. However, the high rate of revisions due to pain and, mostly, primary instability should be investigated in clinical trials.

Total Knee Replacement in Young Patients: Survival and Causes of Revision in a Registry Population.

BACKGROUND: The incidence of total knee replacements (TKRs) in young patients is increasing. Few reports described encouraging results and acceptable survival rates. However, many concerns still persist, in particular about the high rates of infection and aseptic loosening. Aim of this article was to investigate the survival of TKRs in patients aged 45 years or younger in a registry population. METHODS: The Emilia-Romagna registry RIPO was enquired about TKRs in patients ≤45 years; 238 TKRs were evaluated at a mean follow-up of 5.4 years (range 0-15.6 years), examining the features of the patients involved, the survival rate, and the reasons for revision of the knee implants. RESULTS: The TKRs were generally performed in men, in private hospitals, and almost in half of the cases for other causes rather than primary osteoarthritis. The mean age was 40 years. Bicompartmental, cemented posterior-stabilized implants with fixed bearing were preferred. The survival rate was higher than 90% in the first 7 years, and then it decremented. The choice of implant did not apparently influence the survivorship. The final outcomes were acceptable, substantially in line with the previous literature about young patients. Twenty-one revisions occurred (8.8%), in particular 8 cases for aseptic loosening and 7 TKRs for infection. The rate of revision was higher than in overall population and even in some young cohorts. CONCLUSION: TKRs in patients aged 45 years or younger seem a promising procedure, although the high rates of septic and aseptic loosening should be carefully evaluated. Prospective, well-designed studies are required to confirm and investigate these preliminary findings.

Radiological identification of Zweymüller-type femoral stem prosthesis in revision cases.

INTRODUCTION: Since 1979 the number of patients treated with femoral stems has continued to grow, as well as the number of stems with features similar to the Zweymüller prosthesis produced by different companies. Identification can be problematic in case requiring revision. In the present paper, we present an overview of morphometric differences between the different stem designs, which can be useful for radiologic identification in revision cases. METHODS: By doing some research on the Internet of specialized sites and worldwide literature, we searched for all femoral stems agreeing with Zweymüller principles (cementless, straight, tapered, rectangular cross-sectioned femoral stems). RESULTS: We found 26 different stems from different companies producing or having produced in the past the Zweymüller-type femoral stems for hip prosthesis. DISCUSSION: Accurate preoperative identification of the Zweymüller femoral stem type may be of critical importance to eventual outcomes following revision surgery. Each manufacturer has different instruments specific to the removal of their primary implants, and ensuring they are available can simplify the revision procedure significantly. Exact pre-operative planning is also necessary for selecting the correct ball head in cases where a stem is well-fixed and can be left in situ. The commonly used notation "Eurocone 12/14" provides no information about the actual taper angle. Whenever the stem is left in situ, the exact specifications of the taper must therefore be obtained from the manufacturer in order to use a metal sleeve that precisely fits it and the ball head. Failure to do so may result in severe complications, such as metallosis. In cases where it is not possible to identify the taper angle, the surgeon may even consider removal of the stem, though this significantly increases the surgical procedure's invasiveness. Only a single, uniform standard taper, such as that offered until 1994 by CeramTec, can solve these issues in the future. CONCLUSION: The survival rate of the Zweymüller stems after ten years was 96 % and the complication rate was very low. Pre-operative identification of the femoral implant is of considerable importance for planning and correctly implementing revision procedures.

Metal-on-metal hip prostheses: correlation between debris in the synovial fluid and levels of cobalt and chromium ions in the bloodstream.

PURPOSE: Hip prostheses with metal-on-metal (MoM) coupling can release cobalt-chromium particles and ions. The aim of this work is to verify the correlation between particles in the synovial fluid and circulating ions. METHODS: Forty patients were enrolled; particles from synovial fluid were analysed by SEM­EDX (Scanning Electron Microscopy-Energy Dispersion X-rays analysis) and levels of circulating Co and Cr were assayed by ICP-MS (inductively-coupled plasma mass spectrometry). RESULTS: In 16 cases we did not find any particles in the synovial fluid and the Co level in whole blood was 0.05­4.42 ppb; in seven with few particles the blood level was 2.2­15.6 ppb; in six cases with several particles the level was 5.0­54.3 ppb; finally, in 11 cases we isolated not only Co-Cr particles, but also Cr particles with low or absent Co and in these patients the circulating level of Co was 23.8­109.6 ppb. Co in serumand Cr level both whole blood and serum have shown a similar trend to Co; the correlation between all these values and the corresponding particles is statistically significant in all cases. CONCLUSION: Co and Cr both in serum and whole blood represents a systemic representation of the particle release at local level and can therefore be used to confirm a diagnosis and monitor the wear process of MoM articular prostheses.

Detection of cobalt in synovial fluid from metal-on-metal hip prosthesis: correlation with the ion haematic level.

Hip replacement with large metal-on-metal (MoM) coupling has recently been under attention for its metal ions release, inducing several disorders. Since the blood level toxicity threshold for cobalt is known, the aim of this work is to determine whether Co serum and blood levels correlate with the synovial fluid level. Beside this, the synovial fluid Co from patients without prosthesis has also been measured. Co has been determined in 54 samples (32 unilateral MoM and 22 controls) with inductively coupled plasma mass spectrometry in the three matrices. In the prosthesized group, cobalt was significantly higher compared with controls and in the synovial fluid it strongly correlated with whole blood Co (p = 0.847) and serum (p = 0.855). Moreover, the Co levels into whole blood and serum were significantly different. In conclusion, haematic Co concentration correctly reflects Co local level.

Uncemented primary total hip arthroplasty, presentation of pain, and expression of osteonectin.

Osteonectin (ON) is an important matrix glycoprotein highly expressed in bone. In several in vitro and animal model studies, ON was used as indicator of the state of osseointegration of implanted devices. There are, however, no studies on ON expression in the synovial fluid of patients with total hip joint replacement (THJR). The purpose of our study was to determine the ON concentration in synovial fluid from three groups of patients: primary uncemented THJR with hip pain ("pain" group; n = 15) and without pain ("no-pain" group; n = 12), and patients with osteoarthitis scheduled to receive a primary THJR (control group; n = 5). For the prosthesized groups, the statistical nature of the correlation between ON concentration and patient age, in situ life of the THJR, presence of periprosthetic osteolysis, and presence of debris in the synovial fluid was individually investigated. ON concentration was determined using enzyme-linked immunosorbent assay, the presence of periprosthetic osteolysis was established using X-radiography and Engh's criteria, and the presence of debris was determined using digestion and EDX spectroscopy. ON concentration was significantly lower in the "pain" group compared with the "no-pain" one (median values 19.0 and 53.2 ng/mL, respectively). ON concentration in the control group (median value: 16.9 ng/mL) was comparable with that reported in the literature. In the prosthesized groups, ON concentration was not correlated with patient age, in situ life of the prosthesis, presence of periprosthetic osteolysis, or presence of debris in the synovial fluid. Our results suggest that cases of unexplained pain in THJR patients could be treated by paying special attention to the osseointegration status of the implant by using ON concentration as an early indicator of this status.

Ceramic debris in hip prosthesis: correlation between synovial fluid and joint capsule.

Detection of ceramic particles in synovial fluids allows early diagnosis of ceramic damage, but there is no evidence of a relationship between ceramic debris in the articular space and in the joint capsule. The aim of the present study is to verify if the particles isolated in the synovial fluid are comparable with those stored in the capsular tissue. Twenty-one patients were enrolled. Both synovial fluid and capsular samples were collected during revision surgery and ceramic particles were isolated and analyzed by scanning electron microscopy and energy-dispersive X-ray microanalysis. It resulted a significant correlation between the samples couples (18 out of 21). This study confirms that the synovial fluid analysis can give a clear definition of the presence of particles in the joint capsule.

Monocyte chemoattractant protein 1 expression in synovial fluid of patients with total hip arthroplasty.

Monocyte chemoattractant protein 1 (MCP-1) is a member of the chemokines family that stimulates monocyte chemotaxis and whose expression is induced during osseous inflammation. Total hip arthroplasty (THA) now uses ceramic-on-ceramic (cer-cer) or metal-on-metal (met-met) coupling that is considered the bearing of new generation, with improved performance compared with the previous polyethylene bearings. While the ceramic on ceramic is universally considered highly biocompatible, met-met coupling can induce hypersensitivity correlated to immunological response. This study aimed at quantifying the MCP-1 levels in synovial fluid of THA patients with these two articular couplings; synovial fluid of osteoarthritic patients who underwent primary THA was used as a control. The presence of wear particles originating from the prostheses was also assessed in the synovial fluid by scanning electron microscopy and energy dispersive X-ray spectroscopy. The MCP-1 levels in the synovial fluid of 17 patients with met-met coupling were significantly higher than in 13 patients with cer-cer coupling and in seven controls; median MCP-1 level was 919 pg/mL in the cer-cer group, 4274 pg/mL in the met-met group, and 326 pg/mL in the control group. No correlation was found between MCP-1 levels and the presence of wear particles in the synovial fluid, time from surgery, or periprosthetic osteolysis. We conclude that the presence of the prosthesis is responsible for an increase in the level of MCP-1; moreover, the significantly higher level of this chemokine in met-met coupling can be related to inflammatory and possibly hypersensitivity processes induced by metal ions.

Outcomes of total hip replacement in patients with slipped capital femoral epiphysis.

BACKGROUND: Total hip replacement has been advocated for the treatment of degenerative hip diseases secondary to slipped capital femoral epiphysis; nonetheless, outcomes of this procedure have not been well established. We reviewed the outcomes of modern total hip replacements in patients who suffered from slipped capital femoral epiphysis. METHODS: A retrospective study was carried out on 32 total hip replacements performed on 28 patients who suffered from slipped capital femoral epiphysis from August 1994 to January 2007. The average age at the time of surgery was 45 years. Clinical evaluation was performed using the Harris Hip Score, radiographic assessment measuring cup and stem orientation, the extent of osteolysis around the implant, and leg length discrepancy. The average follow-up was 98 months (range 25-204 months). RESULTS: Two total hip replacements failed, one for stem aseptic loosening and the other for modular neck failure. The cumulative survival rate at 9 years was 92.8 %. If the end point was revision for implant loosening, the survival rate improved to 96.8 % at 9 years. The only complication recorded was an intraoperative fracture of the lesser trochanter immediately treated with cerclage wire. At the latest follow-up, the Harris Hip Score averaged 86 (range 70-97). Leg length discrepancies greater than 1 cm were present in 18 cases before surgery, and in only 6 cases after surgery. DISCUSSION: We recommend total hip replacement for patients who suffer from slipped capital femoral epiphysis because of the satisfactory survival, low complication rate, and the possibility of restoring leg length.

Satisfactory clinical and radiologic outcomes with a new shorter and modular stem for end-stage hip osteoarthritis: an international prospective multicentre pilot study.

INTRODUCTION: This multicenter prospective cohort study aimed to assess the safety and clinical and radiologic performance of the CLS® BreviusTM Stem with Kinectiv® Technology. MATERIAL AND METHODS: A total of 222 consecutive subjects, recruited in five different centers, qualifying for primary total hip arthroplasty (THA), were enrolled in the study. All the subjects received the CLS® BreviusTM Stem with Kinectiv® Technology. All the enrolled study subjects underwent pre-operative clinical and radiographic evaluation. Additionally, all subjects underwent post-operative clinical, functional and radiographic evaluations at 6 months and 1, 2, 3, and 5 years. These evaluations included implant survival, pain and functional performance (Harris Hip Score [HHS], University of California, Los Angeles [UCLA] Activity Score, Oxford Hip Score), subject quality-of-life (EQ-5D), radiographic parameters, complications, and concentration of metal ions (aluminum and titanium) in blood. RESULTS: No revisions were performed during the follow-up period. Of the 222 patients, only 76 completed the 5-year follow-up. Only 7 and 5 patients had aluminum and titanium 5-year evaluations, respectively. All the clinical parameters showed an overall improvement in the overtime measured with ANOVA for repeated measures; furthermore, the clinical scores showed a statistically significant improvement at 5 years with respect to pre-operative value (p < 0.001). Aluminum and titanium showed no variation for repeated measures at different time points (p > 0.05). A total of six complications were reported, of which only two were hip-related. CONCLUSIONS: The function of the CLS® BreviusTM Stem with Kinectiv® Technology indicated that subject well-being significantly increased following THA regardless of age, gender, BMI, previous surgery, primary diagnosis, and lifestyle.

Modeling the cost-effectiveness for cement-less and hybrid prosthesis in total hip replacement in Emilia Romagna, Italy.

BACKGROUND: The aim of the present study was to assess the cost-effectiveness of cement-less versus hybrid prostheses in total hip replacement (THR) in patients diagnosed with primary osteoarthritis. METHODS: Effectiveness data were obtained from the Emilia-Romagna Regional Registry on Orthopaedic Prosthesis (RIPO), which collects information on all orthopaedic intervention performed in Emilia-Romagna (41,199 total hip replacements performed from 2000 to 2007), and from which we obtained survival curves and transition probabilities for the cement-less and hybrid prostheses, respectively. Conversely, costs were derived from regional databases through a specific procedure, which allowed us to register individual component's costs for both primary and subsequent revision interventions. A specific Markov transition model was constructed in order to consider the 3 types of revisions that an implant could possibly undergo through its life-span: total, cup or stem, head insert or neck. The cost-effectiveness was expressed in terms of cost per "revision-free" life year. RESULTS AND CONCLUSIONS: Considering a 70-y old patient undergoing THR, the cementless strategy resulted more effective but more costly than the hybrid solution, with an incremental cost effectiveness ratio of 2401.63 € per revision-free life year. Following a deterministic sensitivity analysis, hybrid and cementless fixation showed, respectively, a dominance profile for patients older than 83 y and younger than 43 y, whereas for all ages in between, we report a progressive increase in the ICER of cementless prostheses. Our results proved to be robust, as underlined by the probabilistic sensitivity analysis performed using cost distributions.

Modular neck prostheses in DDH patients: 11-year results.

BACKGROUND: Total hip replacement in developmental dysplasia of the hip is a demanding procedure and usually requires dedicated devices and special surgical techniques. Nevertheless, the described techniques have shown variable outcomes. The aim of this study was to assess the 11-year outcomes of an off-the-shelf modular neck prosthesis in dysplastic patients and to evaluate the ability of the modular neck system to adequately restore femoral offset, abductor muscles lever arm and leg length. METHODS: We retrospectively evaluated 61 modular neck prostheses implanted in 47 patients between June 1995 and March 2004. The preoperative diagnosis was developmental dysplasia of the hip in all cases. The clinical outcomes were assessed using the Harris hip score and the Western Ontario and McMaster Universities score. The femoral offset, abductor muscles lever arm, height and medialization of the hip center of rotation, and differences in leg length were evaluated on postoperative radiographs. Prosthesis survival was calculated according to the Kaplan-Meier method considering any reason for revision as failure. The average follow-up was 117.2 months (range 57-162 months). RESULTS: The cumulative survival at 11 years was 97.5%. One prosthesis failed 5 years after surgery because of a ceramic liner fracture due to an inappropriate obstetric maneuver during labour. At the latest follow-up the mean Harris hip score was 74.7 (range 23-91). Leg length discrepancy was avoided in the majority of cases; femoral offset was almost always restored. CONCLUSIONS: The results of this series support the use of modular neck prostheses as an effective alternative in the treatment of developmental dysplasia of the hip. The modularity was very efficient in restoring offset, leg length and maintaining stability with a good mid-long-term follow-up. Unlike other proposed surgical techniques, these good results are achievable by a standard surgical technique and with an off-the-shelf prosthesis.

Failure of knee osteotomy in a case of neuropathic arthropathy of the knee.

Neuropathic arthropathy (Charcot's joint) is a degenerative process that affects peripheral or vertebral joints as a consequence of a disturbance in proprioception and pain perception. The knee is one of the most frequently affected joints, but even when the diagnosis is made at an early stage there is no consensus on the best treatment options. An early diagnosis of neurosyphilis was made in a 55-year-old woman presenting a delayed union of an asymptomatic Schatzker type IV fracture of the proximal tibia. A medial opening wedge tibial osteotomy was performed to achieve fracture healing, to correct the medial depression of the articular surface, and possibly to avoid an early arthritis typical of the disease. To our knowledge, a knee osteotomy has never been reported at an early stage of neuropathic arthropathy. Even though the clinical and radiographic evaluation performed at 4 months follow-up showed a good stage of healing of the osteotomy and no typical features of neuropathic joint degeneration, at 8 months follow-up the knee was markedly deranged.

Ceramic-on-metal for total hip replacement: mixing and matching can lead to high wear.

Ceramic-on-ceramic and metal-on-metal bearing surfaces are often employed for total hip replacement because of their resistance to wear. However, they have some limits: brittleness is a major concern for ceramic, and ion release is a drawback for metal. To reduce the effect of these limitations, a hybrid coupling of ceramic-on-metal has been proposed. The theoretical advantage of this new coupling might lead orthopedic surgeons to use it indiscriminately. We asked whether the wear rate of this innovative solution was comparable with that of ceramic-on-ceramic, which is considered to be the gold standard for wear resistance. In a hip simulator study, we tested the wear pattern of a hybrid ceramic-on-metal coupling supplied by the same distributor; in particular, three different configurations were tested for 5 million cycles: 36-mm ceramic-on-ceramic, 32-mm and 36-mm ceramic-on-metal. These combinations were gravimetrically and geometrically evaluated. After 5 million cycles, the volumetric loss for the metal acetabular cups (Phi 36-mm) was 20-fold greater than that of the ceramic cups of the same size (Phi 36-mm); a volumetric loss of 4.35 mm(3) and 0.26 mm(3) was observed, respectively, for ceramic-on-metal and ceramic-on-ceramic combinations. Significant statistical differences were observed between all 36-mm different combinations (P < 0.0001). The increased diameter of the 36-mm ceramic-on-metal configuration resulted in a lower volumetric loss compared with that of the 32-mm ceramic-on-metal configuration. Our findings showed an increase in wear for the proposed hybrid specimens with respect to that of the ceramic-on-ceramic ones. This confirms that even in the case of ceramic-on-metal bearings, mixing and matching could not prove effective wear behavior, not even comparable with that of the ceramic-on-ceramic gold standard.