An island of receptor-like genes at the Rrs13 locus on barley chromosome 6HS co-locate with three novel sources of scald resistance.

Three Hordeum spontaneum-derived resistances (referred to as 145L2, 41T1 and 40Y5) have demonstrated long-term effectiveness against barley scald, caused by Rhynchosporium commune, in western Canada. Genetic mapping of these resistances in three populations, and the use of five barley genome assemblies, revealed they co-located to a narrowly defined 0.58-1.2 Mbp region of chromosome 6HS containing the Rrs13 scald resistance gene. Differential disease reactions among the three resistances and a Rrs13 carrier (AB6) to a panel of 24 scald isolates indicated that the four resistances were unique from one another. A marker created to target the 6HS scald locus was screened across a panel of barley germplasm that included H. vulgare, H. spontaneum and H. bulbosum lines. The marker showed specificity to H. vulgare lines known to carry the 6HS scald resistances and to two H. spontaneum lines that trace their origins to Jordan. Within the 0.58-1.2 Mbp region were 2-7 tandemly repeated leucine-rich repeat receptor-like proteins (LRR-RLP) and one lectin receptor-like kinase (Lec-RLK) genes with abundant sequence variation between them. The well-defined role that RLP and RLK genes play in plant defense responses make them logical candidate resistance genes, with one possible hypothesis being that each unique scald resistance may be encoded by a different RLP that interacts with a common RLK. It is suggested the three scald resistances be temporarily named Rrs13145L2, Rrs1341T1 and Rrs1340Y5 to recognize their co-location to the Rrs13 locus until it is determined whether these resistances represent unique genes or alleles of the same gene.

A Quantitative PCR System for Measuring Sclerotinia sclerotiorum in Canola (Brassica napus).

Sclerotinia stem rot, caused by Sclerotinia sclerotiorum, is an economically important disease of canola (Brassica napus) commonly managed by routine application of fungicides. Petal infestation has been demonstrated to be an important stage of the disease cycle in canola and has been the focus of previously developed Sclerotinia stem rot risk assessment methods. Quantitative polymerase chain reaction (qPCR) analysis can provide a more rapid and accurate assessment of petal infestation levels. Primers and a hydrolysis probe were designed to amplify a 70-bp region of an S. sclerotiorum-specific gene, SS1G_00263. A hydrolysis probe-based qPCR assay was developed that had a detection limit of 8.0 × 10-4 ng of S. sclerotiorum DNA and only amplified S. sclerotiorum DNA. Evaluation of petals collected at five sampling points in each of 10 commercial canola fields on each of two sampling dates (corresponding to 20 to 30% bloom and 40 to 50% bloom) revealed S. sclerotiorum DNA infestation levels of 0 to 3.3 × 10-1 ng/petal. This qPCR assay can be used to reliably quantify petal infestation and, with further research, has the potential to serve as the basis for a Sclerotinia stem rot risk assessment tool or as a means to study Sclerotinia stem rot epidemiology.

Diversity of Fusarium head blight populations and trichothecene toxin types reveals regional differences in pathogen composition and temporal dynamics.

Analyses of genetic diversity, trichothecene genotype composition, and population structure were conducted using 4086 Fusarium graminearum isolates collected from wheat in eight Canadian provinces over a three year period between 2005 and 2007. The results revealed substantial regional differences in Fusarium head blight pathogen composition and temporal population dynamics. The 3ADON trichothecene type consistently predominated in Maritime provinces (91%) over the sampled years, and increased significantly (P<0.05) between 2005 and 2007 in western Canada, accounting for 66% of the isolates in Manitoba by the end of the sampling period. In contrast, 3ADON frequency was lower (22%, P<0.001) in the eastern Canadian provinces of Ontario and Québec and did not change significantly between 2005 and 2007, resulting in two distinct longitudinal clines in 3ADON frequency across Canada. Overall, genetic structure was correlated with toxin type, as the endemic population (NA1) was dominated by 15ADON isolates (86%), whereas a second population (NA2) consisted largely of 3ADON isolates (88%). However, the percentage of isolates with trichothecene genotypes that were not predictive of their genetic population assignment (recombinant genotypes) increased from 10% in 2005 to 17% in 2007, indicating that trichothecene type became an increasingly unreliable marker of population identity over time. In addition, there were substantial regional differences in the composition of recombinant genotypes. In western and maritime provinces, NA2 isolates with 15ADON genotypes were significantly more common than NA1 isolates with 3ADON genotypes (P<0.001), and the reverse was true in the eastern provinces of Québec and Ontario. Temporal trends in recombinant genotype composition also varied regionally, as the percentage of 15ADON isolates with NA2 genetic backgrounds increased approximately three fold in western and Maritime provinces, while the opposite trends were observed in Québec and Ontario. The results indicate that F. graminearum population dynamics in Canada have been influenced by a complex adaptive landscape comprising different regional selective pressures, and do not reflect a simple model of dispersal and integration following the introduction of a novel pathogen population. In addition, we identified F. graminearum strains that produce the recently discovered A-trichothecene mycotoxin (NX-2) for the first time in Canada, representing a significant expansion of the known range of NX-2 producing strains in North America.

Adaptation to Brassica Host Genotypes by a Single-Spore Isolate and Population of Plasmodiophora brassicae (Clubroot).

Plasmodiophora brassicae, the cause of clubroot of crucifers, is an increasingly important pathogen of canola (Brassica napus) in Alberta, Canada. In response, clubroot-resistant canola genotypes are being deployed to help reduce yield losses. Two experiments were conducted to examine the effect on P. brassicae virulence of repeated exposure of a population and single-spore isolate of the pathogen to the same host. The first experiment examined changes in the index of disease over five cycles of infection on seven Brassica hosts (European Clubroot Differential [ECD] 02, ECD 04, ECD 05, ECD 15, '45H26', '45H29', and 08N823R). The second experiment tested the virulence of five cycled populations ('45H29', 08N823R, ECD 05, and ECD 15) and three cycled single-spore isolates ('45H29', 08N823R, and ECD05) on four resistant canola genotypes ('73-77', '73-67', VT-SD-09, and '9558C'). The results from these experiments clearly demonstrate the ability of both single-spore isolates and populations of P. brassicae to rapidly erode the resistance present in the two canola genotypes, '45H29' and 08N823R. Although the index of disease increased on these two genotypes, the four resistant canola genotypes remained resistant to all the cycled populations and single-spore isolates in the second experiment. These results underscore the importance of crop rotation in the management of clubroot in Alberta.

Spot Form of Net Blotch Resistance in a Diverse Set of Barley Lines in Australia and Canada.

The responses of 95 barley lines and cultivars to spot form of net blotch (SFNB) caused by Pyrenophora teres f. maculata were analyzed as seedlings and adults in Australia and Canada. Cluster analyses revealed complex reaction responses. Only 2 lines (Esperance Orge 289 and TR3189) were resistant to all isolates at the seedling stage, whereas 15 lines and cultivars (81-82/033, Arimont, BYDV-018, CBSS97M00855T-B2-M1-Y1-M2-Y-1M-0Y, CI9776, Keel, Sloop, Torrens, TR326, VB0111, Yarra, VB0229, WI-2477, WI2553, and Wisconsin Pedigree) were resistant toward the two Canadian isolates and mixture of Australian isolates at the adult stages. In Australian field experiments, the effectiveness of SFNB resistance in three barley cultivars (Barque, Cowabbie, and Schooner) and one breeding line (VB9104) with a different source of resistance was tested. Barque, which possessed a resistance gene that provided complete resistance to SFNB, was the most effective and showed no effect on grain yield or quality in the presence of inoculum. Generally, cultivars with seedling or adult resistance had less disease and better grain quality than the susceptible control, Dash, but they were not as effective as Barque. A preliminary differential set of 19 barley lines and cultivars for P. teres f. maculata is proposed.

Effects of seeding rate, nitrogen rate and cultivar on barley malt quality.

BACKGROUND: Crop management tools have been shown to affect barley kernel size and grain protein content, but the direct effect on malt quality is not well understood. The present study investigated the effect of seeding rate, nitrogen fertilisation and cultivar on malt quality. RESULTS: Higher seeding rates produced barley with less grain protein and smaller, more uniformly sized kernels. The small, uniformly sized kernels modified more completely, leading to malt with higher extract and lower wort ß-glucan than malt from low-seeding-rate barley. Increasing rates of nitrogen fertilisation caused grain protein levels to increase, which limited endosperm modification and reduced malt extract levels. AC Metcalfe showed better modification and higher malt extract than CDC Copeland, but CDC Copeland had better protein modification at higher fertilisation rates, which resulted in less reduction of malt extract as nitrogen rate increased. CONCLUSION: Higher seeding rates reduced kernel size and grain protein levels without compromising malt extract owing to better endosperm modification of the more uniformly sized kernels. Negative effects of higher nitrogen rates on malt quality can be reduced through development of cultivars with improved ability to modify protein during malting.

Multisphere phantom and analysis algorithm for PET image quality assessment.

PET image quality measurements of lesion detectability frequently use a small, radioactive sphere in a larger phantom. The typical analysis of a small single sphere in background has several shortcomings as a measure for detectability and quantitation: the measurement has low statistical power; the region of interest (ROI) is susceptible to large pixel-to-pixel fluctuations; only a single point in the axial and transaxial field of view is analyzed; background noise measurements in regions away from the signal sphere may bias the detectability measurement and user-placed ROIs can cause inconsistent measurements. For a more robust measurement and repeatable analysis of small lesion detectability in PET images, a multisphere phantom and analysis algorithm were developed. The multisphere phantom consists of a collection of 50 1.0-cm spheres, mounting rods and a gridded plate. A PET/CT study is presented where 29 spheres with a 4:1 sphere-to-background radioactivity ratio were acquired for multiple frame durations and reconstructed. An analysis algorithm was implemented and applied to the acquired PET/CT that detects the contrast-enhanced spheres in a CT, places ROIs on the spheres and their respective proximal background, applies the ROIs to the PET and performs quantitation. Results are presented that show the impact of increasing number of signal spheres and of different background ROI placement methods on the image quality measurement. Increasing the number of spheres reduced the variability in the image quality measurements, but only up to a point, beyond which increasing the number of spheres did not considerably reduce the variability. A phantom with numerous spherical inserts increases several measurement aspects: the flexibility of sphere placement during setup, the number of radioactivity concentrations that can be used during a single study and the statistical power of measurements. Additionally, an automated algorithm that localizes spheres, places ROIs and performs quantitation will increase reliability and reproducibility of image quality assessment, in addition to simplifying the analysis.

Fungicide and Cultivar Management of Leaf Spot Diseases of Winter Wheat in Western Canada.

A complex of leaf-spotting diseases-tan spot, the Septoria complex, spot blotch, and powdery mildew-are frequently observed on winter wheat in western Canada; however, there are few studies indicating varietal differences in reaction to these diseases or the benefit of fungicide application. To determine the benefit of varietal improvement and multiple fungicide treatments and application timings, field experiments were conducted at six site-years in western Canada. Two cultivars varying in reaction to leaf spot diseases were used in combination with fungicide treatments. Disease severity ranged from trace to 64% of the combined flag and penultimate leaf area diseased, differed between cultivars, and was reduced from the check by some fungicide treatments. Yield improvement by fungicide treatment varied from 3.3 to 13.2% greater than the nontreated check. At two site-years, the split application of two half rates of fungicide resulted in the greatest yield; however, in both cases, the yield benefit did not differ from a single application at the flag leaf growth stage. Cultivar selection and fungicide use under environments conducive to disease are beneficial components of an integrated leaf spot disease management program for winter wheat in western Canada.

The utility of SPECT lung perfusion scans in minimizing and assessing the physiologic consequences of thoracic irradiation.

PURPOSE: Three-dimensional single photon emission computed tomography lung perfusion scans (SPECT) provide a unique quantitative 3-dimensional map of the distribution of functioning pulmonary vascular/alveolar subunits, information not provided by other imaging modalities. This report describes our initial experience utilizing these scans to assist in the design of radiation treatment beams and to assess changes in regional lung function following irradiation. METHODS AND MATERIALS: Patients were immobilized and scanned in the treatment position with appropriate fiducial markers. Four millicuries of technetium 99M microaggregated albumin were injected and SPECT images of the lung were generated. Pre-treatment SPECT images were used to help design radiation beams to minimize irradiation of functioning lung. Pre- and post-treatment scans were compared to assess changes in regional function. These changes in function were then correlated with the regional radiation dose. RESULTS: Pre-radiotherapy SPECT scans were obtained in 18 patients (11 with lung cancer). Marked variations in regional function were frequently noted. In patients with primary lung tumors, these variations were not necessarily immediately adjacent to the tumor volume. In general, patients with poor pulmonary function pre-treatment, in whom one would like to spare as much normal lung as possible, had the most non-uniform distribution throughout the lung of functioning vascular/alveolar subunits. In these cases, pre-treatment scans were most useful in designing radiation portals to minimize irradiation of functioning lung. SPECT scans were also used to detect changes in regional lung function secondary to radiotherapy in four patients. With doses in excess of 40 Gy, reductions in regional function were noted 1-6 months following completion of radiotherapy. These reductions were not necessarily accompanied by reductions in conventional pulmonary function tests, which are assessments of whole lung function and may not reflect regional lung injury if the volume affected is small. CONCLUSIONS: SPECT lung scans provide an excellent means of assessing regional lung function, superior to that obtainable with planar images. The functional data provided by the SPECT images is useful in designing "optimal" radiation treatment beams and in assessing the effect of radiotherapy on regional lung functions. Efforts are continuing in our laboratory to develop a dose response curve for regional lung damage using the tools of SPECT scanning and 3-dimensional dose calculations.

Volume and activity quantitation with iodine-123 SPECT.

UNLABELLED: The goals of this study were to investigate the effect of septal penetration on 123I SPECT activity quantitation using low-energy, high-resolution collimators, and to evaluate a semi-automatic method for measuring volume and activity of 123I distribution with SPECT. METHODS: Data were acquired from experimental phantoms containing spheres filled with a high-purity 123I solution. The penetration study compared the reconstructed activity of a 3.4-cm diameter sphere with and without the presence of surrounding activity. In the study of volume and activity quantitation, three different size spheres (diameters of 1.8 cm, 2.8 cm and 3.4 cm) were imaged in three different sphere-to-background (S:B) 123I concentration ratios (2.5, 5 and 10) with low-energy collimators. The filtered backprojection reconstruction method was used with compensation for scatter, attenuation and detector response. Volume and activity measurements were obtained from the SPECT image using a semiautomatic gradient technique which estimates the location of the sphere/boundary in three dimensions. RESULTS: With the low-energy collimator, there was only a small (< 2%) increase in the measured activity of the sphere when surrounding activity was present. The measured volume for the two largest spheres was within 5% of the true volume for all S:B ratios. The activity measurement of these spheres was consistently underestimated by 20%-25% but suggested that the accuracy could be improved with calibration. For the smallest sphere, the volume was grossly overestimated and only at the 10 S:B ratio was the activity measured reasonably accurately (< 20%). CONCLUSIONS: The low-energy collimators used in this study are suitable for quantitative 123I SPECT. Accurate SPECT volume and activity quantitation of 123I distribution can be achieved by semiautomatic means at clinical count densities for objects as small as 2.8 cm in diameter and reasonable activity quantitation is possible for smaller objects with an S:B ratio of at least 10.

Transmission scanning system for a gamma camera coincidence scanner.

UNLABELLED: The goal of this research was to develop and evaluate a practical transmission scanning system for attenuation correction on a 2-head gamma camera coincidence scanner. METHODS: The transmission system operates in singles mode and uses point sources of 137Cs that emit 662-keV gamma-radiation. Each point source is inserted between existing septa that are normally used to provide an approximately 2-dimensional emission acquisition geometry. The sources are placed along a line parallel to the axis of rotation near the edge of 1 camera. Data are acquired with the opposing camera. The septa provide axial collimation for the sources so that the transmission system operates in a 2-dimensional offset fanbeam geometry. Camera energy and spatial resolution were measured at 511 and 662 keV. Sensitivity was measured at 662 keV. The effects on axial resolution of adding supplemental collimation to the septa were shown. The system was calibrated and tested using a resolution (rod) phantom and a uniformity phantom. Torso phantom data were acquired. Patient transmission and emission scans were obtained. Postinjection transmission data were used to correct patient emission data. RESULTS: The camera resolution at postinjection counting rates was 11.7% full width at half maximum (FWHM) for 662-keV gamma-rays. Intrinsic spatial resolution was 2.7 mm (FWHM) at 662 keV. The sensitivity of the system was 280 Hz/MBq using five 74-MBq sources of 137Cs in the transmission geometry, with supplemental collimation added to the septa to improve axial resolution. The transaxial resolution of the system was such that the smallest rods (6-mm diameter and 12-mm spacing) were well resolved in a reconstructed resolution-phantom image. The corrected patient emission scans were free of attenuation-induced artifacts. CONCLUSION: An easily implemented transmission system for a 2-head gamma camera coincidence scanner that can be used for postinjection transmission scanning has been developed.

An evaluation of lesion detectability with cone-beam, fanbeam and parallel-beam collimation in SPECT by continuous ROC study.

UNLABELLED: To evaluate lesion detectability for clinical evaluation of cone-beam (CB), fanbeam (FB) and parallel-beam (PB) collimator sensitivity, experimentally acquired phantom data were used to assess the advantage of CB collimation over conventional collimation. METHODS: Lesion detectability with CB, FB and PB collimation in SPECT was compared using a three-dimensional brain phantom and continuous receiver operating characteristic (CROC) analysis. A simulated cold lesion was located near the posterior portion of the thalamus. High count density scans of this phantom were acquired with CB, FB and PB collimators with similar resolution. These projections were scaled to count levels which reflected the measured sensitivities of the three collimators. Computer-generated Poisson noise was added to the projections to produce uncorrelated data sets. Images were reconstructed using a filtered backprojection algorithm. All reconstructions used a Hann filter with multiplicative attenuation correction. Each of seven trained observers viewed 288 sets of images and indicated the certainty of perceiving a cold lesion at a specified location by a rating of 0-100. Each image set contained four adjacent slices centered on the lesion to minimize partial volume effects. The program LABROC4 was used to fit CROC curves to individual observers' ratings. A t-test for paired data was performed on the individual areas. RESULTS: The average areas (standard deviations) under CROC curves for CB, FB and PB were 0.89 (0.03), 0.83 (0.05) and 0.76 (0.04), respectively. The differences of the areas were statistically significant with all two-tailed p values < 0.02. CONCLUSION: These results demonstrate that cold lesions in the posterior portion of the thalamus are best detected by images obtained using CB followed by FB and PB collimation.

Accuracy of registration of PET, SPECT and MR images of a brain phantom.

Accuracy of a surface-fitting algorithm for three-dimensional image registration of single photon emission computed tomography (SPECT), positron emission tomography (PET), and magnetic resonance (MR) images was tested using a three-dimensional, water-fillable brain phantom. Multislice or volume image sets were acquired for each modality. Small fiducial markers were attached to assess accuracy of surface fitting and provide an alternate fitting technique. A maximum gradient technique was found to work well for SPECT and PET edge detection. Transformation parameters for translation, rotation and scaling were determined by surface fit to match each SPECT and PET scan with MR images. Using the markers, overall translation errors were found to be < 2 mm in each direction and rotational errors < 2 degrees in every case. Errors for specific internal regions were also determined to be < 2 mm for most regions, with only a few fits resulting in errors > 3 mm for some cortical regions. Results indicate surface fitting to be sufficiently accurate for visual comparison of registered images and for enhanced SPECT and PET region of interest (ROI) determination and image reconstruction.

Performance characteristics of a whole-body PET scanner.

METHODS: This study characterizes the performance of a newly developed whole-body PET scanner (Advance, General Electric Medical Systems, Milwaukee, WI). The scanner consists of 12,096 bismuth germinate crystals (4.0 mm transaxial by 8.1 mm axial by 30 mm radial) in 18 rings, giving 35 two-dimensional image planes through an axial field of view of 15.2 cm. The rings are separated by retractable tungsten septa. Intrinsic spatial resolution, scatter fraction, sensitivity, high count rate performance and image quality are evaluated. RESULTS: Transaxial resolution (in FWHM) is 3.8 mm at the center and increases to 5.0 mm tangential and 7.3 mm radial at R = 20 cm. Average axial resolution decreases from 4.0 mm FWHM at the center to 6.6 mm at R = 20 cm. Scatter fraction is 9.4% and 10.2% for direct and cross slices, respectively. With septa out, the average scatter fraction is 34%. Total system sensitivity for true events (in kcps/(microCi/cc)) is 223 with septa in and 1200 with septa out. Dead-time losses of 50% correspond to a radioactivity concentration of 4.9 (0.81) microCi/cc and a true event count rate of 489 (480) kcps with septa in (out). Noise-equivalent count rate (NECR) for the system as a whole shows a maximum of 261 (159) kcps at a radioactivity concentration of 4.1 (0.65) microCi/cc with septa in (out). NECR is insensitive to changes in lower gamma-energy discrimination between 250-350 keV. CONCLUSIONS: The results show the performance of the newly designed PET scanner to be well suited for clinical and research applications.

Attenuation correction in hybrid positron emission tomography.

Attenuation effects are more severe for coincidence imaging than for single-photon imaging. The capability to measure and correct attenuation now exists with dedicated positron emission tomography (PET) scanners. Attenuation correction may or may not improve lesion detection in various situations, but it definitely produces a more realistic radioactivity distribution and is essential for quantitation, which is an important PET capability. For hybrid PET systems, though, which are relatively new and in which neither the performance nor the cost of the scanner can be compromised much compared with the conventional nuclear medicine device alone, attenuation correction is still novel. Just as the entire modality of PET imaging on hybrid gamma cameras has expanded very rapidly, the capability to achieve attenuation correction has quickly followed. Both radioactive source-based and x-ray-based systems exist that provide adequate maps for attenuation correction, and the x-ray systems go even further to provide anatomic detail to aid in image interpretation.

Multimodality nuclear medicine imaging in three-dimensional radiation treatment planning for lung cancer: challenges and prospects.

The purpose of this study was to determine the utility of quantitative single photon emission computed tomography (SPECT) lung perfusion scans and F-18 fluorodeoxyglucose positron emission computed tomography (PET) during X-ray computed tomography (CT)-based treatment planning for patients with lung cancer. Pre-radiotherapy SPECT (n = 104) and PET (n = 35) images were available to the clinician to assist in radiation field design for patients with bronchogenic cancer. The SPECT and PET scans were registered with anatomic information derived from CT. The information from SPECT and PET provides the treatment planner with functional data not seen with CT. SPECT yields three-dimensional (3D) lung perfusion maps. PET provides 3D metabolic images that assist in tumor localization. The impact of the nuclear medicine images on the treatment planning process was assessed by determining the frequency, type, and extent of changes to plans. Pre-radiotherapy SPECT scans were used to modify 11 (11%) treatment plans; primarily altering beam angles to avoid highly functioning tissue. Fifty (48%) SPECT datasets were judged to be 'potentially useful' due to the detection of hypoperfused regions of the lungs, but were not used during treatment planning. PET data influenced 34% (12 of 35) of the treatment plans examined, and resulted in enlarging portions of the beam aperture (margins) up to 15 mm. Challenges associated with image quality and registration arise when utilizing nuclear medicine data in the treatment planning process. Initial implementation of advanced SPECT image reconstruction techniques that are not typically used in the clinic suggests that the reconstruction method may influence dose response data derived from the SPECT images and improve image registration with CT. The use of nuclear medicine transmission computed tomography (TCT) for both SPECT and PET is presented as a possible tool to reconstruct more accurate emission images and to aid in the registration of emission data with the planning CT. Nuclear medicine imaging techniques appear to be a potentially valuable tool during radiotherapy treatment planning for patients with lung cancer. The utilization of accurate nuclear medicine image reconstruction techniques and TCT may improve the treatment planning process.

Cerebellar activity and disturbed time sense after THC.

Because marijuana continues to be the most commonly used illicit drug, its effects on the brain function are of major interest. We utilized positron emission tomography (PET) and magnetic resonance imaging (MRI) to study the effects of delta-9-tetrahydrocannabinol (THC) infusion on brain blood flow and its behavioral correlates in 46 volunteers. Consistent with previous reports, there was a significant increase in cortical and cerebellar blood flow following THC, but not all subjects showed this effect. Those who showed a decrease in cerebellar CBF also had a significant alteration in time sense. The relationship between decreased cerebellar flow and impaired time sense is of interest because the cerebellum has been linked to an internal timing system.

Quantitation of 211At in small volumes for evaluation of targeted radiotherapy in animal models.

We have evaluated SPECT and two planar imaging methods, geometric mean (GM) and buildup factor (BF), for their potential to quantitate in vivo 211At distributions in rat spinal subarachnoid spaces using phantom studies. The use of medium-energy collimators and the small diameter (3 mm) of the subarachnoid space complicate quantitation. Net activities from distributions in various backgrounds were obtained using a large region of interest with background subtraction. Results showed quantitation accuracy within 10% for SPECT and BF in low backgrounds increasing to 25% at higher background levels while GM errors ranged from 20 to 45%. We have also obtained images of [211At]astatide distributions, administered intrathecally, in rats.

Marijuana intoxication and brain activation in marijuana smokers.

OBJECTIVE AND METHOD: The acute effects of delta9 tetrahydrocannabinol (THC) on cerebral blood flow (CBF) were studied in human subjects. Regional CBF was measured with 15O-water and Positron Emission Tomography (PET) in 32 volunteers with a history of exposure to marijuana. Scans were performed before and after intravenous (I.V.) infusion of either of two doses of THC or a placebo, given under double blind conditions. RESULTS: THC but not placebo increased CBF especially in the frontal regions bilaterally, insula and cingulate gyrus and sub-cortical regions with somewhat greater effects in the right hemisphere. While most regions showed significant change at 60 minutes for the lower dose group, the higher dose group had significant change at 30 and 60 minutes. There was a highly significant change in the anterior/posterior ratio for the two THC groups reflecting minimal change in occipital flow but significant increases in frontal flow. Self ratings of THC intoxication showed significant effects, and regression analysis indicated it correlated most markedly with the right frontal region. CONCLUSION: Behavioral manifestations of marijuana intoxication may be associated with increased functional activity of the brain especially the frontal cortex, insula and cingulate gyrus.

Calculation of attenuation factors from combined singles and coincidence emission projections.

We have developed a simple method for determining coincidence attenuation-correction factors C (the inverse of the total attenuation factors) from collimated singles (SPECT) and coincidence [positron emission tomography (PET)] projections without transmission data. Attenuation-correction factor estimates are determined for individual lines of response (LOR's) independently. The required data can be acquired using a gamma-camera system with coincidence capabilities. A first-order approximation (R) of C for an LOR is given by the product of the singles count rates, taken at each end of the LOR divided by the square of the coincidence count rate. The method was tested using simulated singles and coincidence projections starting with emission and attenuation maps from patient PET scans. Noise and resolution effects were modeled in separate studies. In the noise-free, high-resolution simulations, a scatter plot of the C values versus the corresponding R values for all LOR's produces a well-defined trajectory with little variance. Values of lnR were reconstructed into good quality attenuation maps that compare favorably with the originals. We conclude that the method works well on ideal data. The introduction of noise results in degraded images. In a simulated patient study, lung and outer body boundaries were visible in images produced with 3.2 x 10(4) coincidence counts.