Synthesis of catalysts with fine platinum particles supported by high-surface-area activated carbons and optimization of their catalytic activities for polymer electrolyte fuel cells.

Herein, we demonstrated that carbon-supported platinum (Pt/C) is a low-cost and high-performance electrocatalyst for polymer electrolyte fuel cells (PEFCs). The ethanol reduction method was used to prepare the Pt/C catalyst, which was realized by an effective matching of the carbon support and optimization of the Pt content for preparing a membrane electrode assembly (MEA). For this, the synthesis of Pt/C catalysts with different Pt loadings was performed on two different carbons (KB1600 and KB800) as new support materials. Analysis of the XRD pattern and TEM images showed that the Pt nanoparticles (NPs) with an average diameter of ca. 1.5 nm were uniformly dispersed on the carbon surface. To further confirm the size of the NPs, the coordination numbers of Pt derived from X-ray absorption fine structure (XAFS) data were used. These results suggest that the NP size is almost identical, irrespective of Pt loading. Nitrogen adsorption-desorption analysis indicated the presence of mesopores in each carbon. The BET surface area was found to increase with increasing Pt loading, and the value of the BET surface area was as high as 1286 m2 gcarbon -1. However, after 40 wt% Pt loading on both carbons, the BET surface area was decreased due to pore blockage by Pt NPs. The oxidation reduction reaction (ORR) activity for Pt/KB1600, Pt/KB800 and commercial Pt/C was evaluated by Koutecky-Levich (K-L) analysis, and the results showed first-order kinetics with ORR. The favourable surface properties of carbon produced Pt NPs with increased density, uniformity and small size, which led to a higher electrochemical surface area (ECSA). The ECSA value of the 35 wt% Pt/KB1600 catalyst was 155.0 m2 gpt -1 higher than that of the Pt/KB800 and commercial Pt/C (36.7 wt%) catalysts. A Higher ECSA indicates more available active sites for catalyst particles. The single cell test with MEA revealed that the cell voltage in the high current density regions depends on the BET surface area, and the durability of the 35 wt% Pt/KB1600 catalyst was superior to that of the 30 wt% Pt/KB800 and commercial Pt/C (46.2 wt%) catalysts. This suggests that an optimal ratio of Pt to Pt/KB1600 catalyst provides adequate reaction sites and mass transport, which is crucial to the PEFC's high performance.

In situ Scanning Electron Microscopy of Silicon Anode Reactions in Lithium-Ion Batteries during Charge/Discharge Processes.

A comprehensive understanding of the charge/discharge behaviour of high-capacity anode active materials, e.g., Si and Li, is essential for the design and development of next-generation high-performance Li-based batteries. Here, we demonstrate the in situ scanning electron microscopy (in situ SEM) of Si anodes in a configuration analogous to actual lithium-ion batteries (LIBs) with an ionic liquid (IL) that is expected to be a functional LIB electrolyte in the future. We discovered that variations in the morphology of Si active materials during charge/discharge processes is strongly dependent on their size and shape. Even the diffusion of atomic Li into Si materials can be visualized using a back-scattering electron imaging technique. The electrode reactions were successfully recorded as video clips. This in situ SEM technique can simultaneously provide useful data on, for example, morphological variations and elemental distributions, as well as electrochemical data.

In situ SEM observation of the Si negative electrode reaction in an ionic-liquid-based lithium-ion secondary battery.

By exploiting characteristics such as negligible vapour pressure and ion-conductive nature of an ionic liquid (IL), we established an in situ scanning electron microscope (SEM) method to observe the electrode reaction in the IL-based Li-ion secondary battery (LIB). When 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)amide ([C2mim][FSA]) with lithium bis(trifluoromethanesulfonyl)amide (Li[TFSA]) was used as the electrolyte, the Si negative electrode exhibited a clear morphology change during the charge process, without any solid electrolyte interphase (SEI) layer formation, while in the discharge process, the appearance was slightly changed, suggesting that a morphology change is irreversible in the charge-discharge process. On the other hand, the use of 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide ([C2mim][TFSA]) with Li[TFSA] did not induce a change in the Si negative electrode. It is interesting to note this distinct contrast, which could be attributed to SEI layer formation from the electrochemical breakdown of [C2mim](+) at the Si negative electrode|separator interface in the [C2mim][TFSA]-based LIB. This in situ SEM observation technique could reveal the effect of the IL species electron-microscopically on the Si negative electrode reaction.

Equilibrium Geometries and Structural Stability of the AlmNan (m = 2-4; n = 1-8) Clusters.

The stable geometries and formation processes of the AlmNan (m = 2-4; n = 1-8) clusters were investigated using the density functional theory (DFT). The Alm (m = 2-4) structures are maintained in the clusters. The Na atoms are attached to the Al-Al bond or Al plane for less than n = 4 in the AlmNan (m = 2-4) clusters. The odd electron of the attached Na atom is transferred to the Alm part for n ≤ 4 or 5 in the AlmNan (m = 2-4) clusters since the Alm part becomes stable. The Na-Na bonding is formed by the attached Na atom after saturation of the Al-Al bonds or Al atoms. The Al2Na5, Al3Na5, Al3Na6, Al3Na7, and Al3Na8 clusters have a characteristic structure. The Na wing is formed in the Al3Nan (n = 5-8) clusters. The 2S shell containing the 3s orbital of the Na atom and the 3p orbital of the Al atom becomes stable before the occupation of the 1D shell because the electrons are delocalized on the Na plane for n ≥ 5 in the AlmNan (m = 2-4) clusters. The stability of the AlmNan (m = 2-4; n = 1-8) clusters was evaluated by comparison of the vertical ionization potential (IP), HOMO-LUMO gap, adsorption energy of the Na atom, and binding energy per atom.