Determination of organic priority pollutants in the low nanogram-per-litre range in water by solid-phase extraction disk combined with large-volume injection/gas chromatography-mass spectrometry.

Polybrominated diphenyl ethers, polychlorinated biphenyls, polycyclic aromatic hydrocarbons and organochlorine pesticides in the low nanogram-per-litre range in water were enriched by solid-phase extraction (SPE) disks and their concentration determined by large-volume injection/gas chromatography-mass spectrometry (LVI/GC-MS). One advantage of using SPE disks in comparison with SPE cartridges is that suspended particulate matter (SPM) does not have to be separated prior to the enrichment step, which saves time and effort. To increase the sensitivity of the method, the SPE disk procedure was combined with LVI/GC-MS, which has not been reported so far for water analysis. The method was calibrated in ranges from 0.25 to 2.5 ng/L and from 2.5 to 25 ng/L. The average recovery was 76% at an analyte concentration of 2.5 ng/L. The limits of quantification, defined at a signal-to-noise ratio of 6:1, reach from 0.1 to 24.0 ng/L and are up to 400 times lower than previously reported in water analysis. By the developed SPE/LVI/GC-MS method, it is possible to investigate the whole water sample without prior separation of the SPM within 2 h including GC-MS analysis.

Fully automated standard addition method for the quantification of 29 polar pesticide metabolites in different water bodies using LC-MS/MS.

A reliable quantification by LC-ESI-MS/MS as the most suitable analytical method for polar substances in the aquatic environment is usually hampered by matrix effects from co-eluting compounds, which are unavoidably present in environmental samples. The standard addition method (SAM) is the most appropriate method to compensate matrix effects. However, when performed manually, this method is too labour- and time-intensive for routine analysis. In the present work, a fully automated SAM using a multi-purpose sample manager "Open Architecture UPLC®-MS/MS" (ultra-performance liquid chromatography tandem mass spectrometry) was developed for the sensitive and reliable determination of 29 polar pesticide metabolites in environmental samples. A four-point SAM was conducted parallel to direct-injection UPLC-ESI-MS/MS determination that was followed by a work flow to calculate the analyte concentrations including monitoring of required quality criteria. Several parameters regarding the SAM, chromatography and mass spectrometry conditions were optimised in order to obtain a fast as well as reliable analytical method. The matrix effects were examined by comparison of the SAM with an external calibration method. The accuracy of the SAM was investigated by recovery tests in samples of different catchment areas. The method detection limit was estimated to be between 1 and 10 ng/L for all metabolites by direct injection of a 10-µL sample. The relative standard deviation values were between 2 and 10% at the end of calibration range (30 ng/L). About 200 samples from different water bodies were examined with this method in the Rhine and Ruhr region of North Rhine-Westphalia (Germany). Approximately 94% of the analysed samples contained measurable amounts of metabolites. For most metabolites, low concentrations ≤0.10 µg/L were determined. Only for three metabolites were the concentrations in ground water significantly higher (up to 20 µg/L). In none of the examined drinking water samples were the health-related indication values (between 1 and 3 µg/L) for non-relevant metabolites exceeded.

Occurrence of residual water within disk-based solid-phase extraction and its effect on GC-MS measurement of organic extracts of environmental samples.

Solid-phase extraction (SPE) is a widespread and powerful sample preparation technique in many analytical areas. Many of the used methods reduce residual water during sample preparation by drying the phase material. Despite the importance of this step, hardly any study deals specifically with the drying process, and if so, only few aspects are mentioned. The present study is the first systematic investigation of the drying process using SPE disks, including the influence of process parameters on the amount of residual water and its consequences for subsequent elution and gas chromatography-mass spectrometry (GC-MS) analysis. The following points were investigated in detail: (1) the change of pressure and volume flow during the drying process, (2) the remaining amount of water at different drying times for different SPE materials, (3) the influence of suspended particulate matter on the drying process and (4) the effects of the residual water on the elution step by using different organic solvents. The study shows that the volume of residual water in the SPE disk is affected by the fixation of the sorbent, the phase material, the amount of sorbent, the pumping settings and the duration of the drying process. Furthermore, systematic investigations demonstrate the influence of residual water on the GC-MS analysis and show analytical interferences only for a few of the investigated analytes. All results suggest that more problems in SPE GC-MS methods are caused by residual water than previously assumed.

Reduction of matrix effects and improvement of sensitivity during determination of two chloridazon degradation products in aqueous matrices by using UPLC-ESI-MS/MS.

The development and validation of a sensitive and reliable detection method for the determination of two polar degradation products, desphenyl-chloridazon (DPC) and methyl-desphenyl-chloridazon (MDPC) in surface water, ground water and drinking water is presented. The method is based on direct large volume injection ultra-performance liquid chromatography electrospray tandem mass spectrometry. This simple but powerful analytical method for polar substances in the aquatic environment is usually hampered by varying matrix effects, depending on the nature of different water bodies. For the two examined degradation products, the matrix effects are particularly strong compared with other polar degradation products of pesticides. Therefore, matrix effects were studied thoroughly with the aim of minimising them and improving sensitivity during determination by postcolumn addition of ammonia solution as a modifier. An internal standard was used in order to compensate for remaining matrix effects. The calibration curve shows very good coefficients of correlation (0.9994 for DPC and 0.9999 for MDPC). Intraday precision values were lower than 5 % for DPC, 3 % for MDPC and the limits of detection were 10 ng/L for both substances. The method was successfully used in a national round robin test with a deviation between 3 and 8 % from target values. Finally, about 1,000 samples from different water bodies have been examined with this method in the Rhine and Ruhr region of North-Rhine-Westphalia (Germany) and in the European Union. Approximately 76 % of analysed samples contained measurable amounts of DPC at concentrations up to 8 µg/L while 53 % of the samples showed MDPC concentrations up to 2.3 µg/L.

Determination of the polar pesticide degradation product N,N-dimethylsulfamide in aqueous matrices by UPLC-MS/MS.

This study presents a fast, sensitive, and robust method for the determination of the polar pesticide degradation product N,N-dimethylsulfamide (DMS) in water based on ultraperformance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). To provide a robust analysis method, the use of an internal standard for both natural waters and model water was examined in order to compensate for matrix effects. The relative standard deviation was found to be +/-15% (n = 10) and the limit of detection was 10 ng/L by direct injection in the UPLC-MS/MS system. The only sample preparation step required is the addition of the internal standard. The chromatographic analysis of one sample takes 4 min and thus is applicable for economic routine laboratory work. More than 600 samples of drinking water, surface water, and groundwater have been examined successfully with this method in the Rhine and Ruhr region of North Rhine Westphalia (Germany). Approximately 65% of analyzed samples contained measurable amounts of DMS at concentrations up to 63 microg/L.

Determination of perfluorooctanoic acid and perfluorooctane sulfonate in Lake Victoria Gulf water.

In this study we present a report of investigation from the screening of perfluorooctanoic acid and perfluorooctane sulfonate in Lake Victoria Gulf and in its source rivers. The first determined levels of perfluorinated alkylated substances in Lake Victoria ecosystem are presented. Variability in the concentrations of perfluorooctanoic acid or perfluorooctane sulfonate in river waters (range perfluorooctanoic acid 400-96,400 and perfluorooctane sulfonate <400-13,230 pg/L) was higher than for Lake waters (range perfluorooctanoic acid 400-11,650 and perfluorooctane sulfonate <400-2,530 pg/L respectively) suggesting generalized point sources such as domestic and industrial waste. The lowest limit of quantification was 400 pg/L for both analytes and limit of detection were 75 and 40 pg/L for perfluorooctanoic acid and perfluorooctane sulfonate respectively. Typical values for precision obtained were 0.14-3.7%, with concentrations range from 400 pg/mL to 1 microg/mL).

Stability of organochlorine pesticides during storage in water and loaded SPE disks containing sediment.

With regard to the Water Framework Directive (WFD) and the required investigation of the whole water sample including suspended particulate matter (SPM), a storage stability study was conducted to determine the suitable storage time and conditions of 21 organochlorine pesticides (OCPs) spiked in water samples and pre-concentrated on solid-phase extraction disks (SPE disks). Furthermore, this work demonstrates the behaviour of three different certified sediment reference materials (CRMs) contaminated with OCPs in water samples as well as loaded on SPE disks under different temperature conditions and storage time periods. Extracts collected on SPE disks were stored for 3, 14 and 30 days at both 4 °C and -18 °C in darkness covered in (a) freezer bags and (b) aluminum foil. With few exceptions the results of these tests demonstrate stability of OCPs up to 30 days at -18 °C. The recoveries for most substances range between 84% and 133%. Furthermore, the stability of OCPs in water samples additionally spiked with CRM up to 500 mg and stored at a temperature of 4 °C in darkness up to 56 days was investigated. The addition of sodium azide enhanced the stability of some substances during storage, especially the endosulfans (I, II) but most substances were stable regardless of sodium azide addition over the entire storage period. An important conclusion of this study is that the storage of loaded SPE disks is an appropriate alternative to storing water samples.

Influence of the drying step within disk-based solid-phase extraction both on the recovery and the limit of quantification of organochlorine pesticides in surface waters including suspended particulate matter.

In this study, 21 organochlorine pesticides (OCPs) were determined based on sample preparation using solid-phase extraction disks (SPE disks) coupled with programmable temperature vaporizer (PTV)-large-volume injection gas-chromatography mass spectrometry (LVI-GC-MS). The work includes a comprehensive testing scheme on the suitability of the method for routine analysis of surface and drinking water including suspended particulate matter (SPM) with regard to requirements derived from the European Water Framework Directive (WFD, Directive 2000/60/EC). SPM is an important reservoir for OCPs, which contributes to the transport of these compounds in the aquatic environment. To achieve the detection limits required by the WFD, a high pre-concentration factor during sample preparation is necessary, which was achieved by disk SPE in this study. The performance of disk SPE is strongly influenced by the drying step, which could be significantly improved by effective elimination of the residual water by combination of a high vacuum pump and a low humidity atmosphere. Detection limits of the WFD in the ng/L range were achieved by large volume injection of 100µL sample extract. The recoveries ranged from 82% to 117% with an RSD smaller than 13%. The applicability of this method to natural samples was tested for instrumental qualification and system suitability evaluation. Successful participation in an interlaboratory comparison proved the suitability of the method for routine analysis.

Multi-component trace analysis of organic xenobiotics in surface water containing suspended particular matter by solid phase extraction/gas chromatography-mass spectrometry.

Suspended particulate matter (SPM) often disturbs the analysis of surface water by conventional methods, such as liquid-liquid extraction (LLE) or solid phase extraction (SPE), caused by insufficient extraction or by plugging. Water and SPM are therefore often separately analysed, which is associated with high expenditure of time, work and costs. Hence, SPM is partly ignored, if the fraction of sorptively bound analytes is small compared to the total analyte concentration. However, the European Water Framework Directive (WFD, Directive 2000/60/EC) requires explicitly an investigation of the whole water sample including SPM, because many priority and priority hazardous substances can sorb substantially to SPM. Therefore, an SPE disk based method was developed for the determination of 54 priority and priority hazardous pollutants including polycyclic aromatic hydrocarbons (PAH), polychlorinated biphenyls (PCB), polybrominated diphenyl ethers (PBDE), organic chlorinated pesticides (OCP) and other pesticides in surface water containing SPM. The developed SPE disk method allows analysis of 1L surface water containing up to 1000 mg SPM without prior separation of SPM in about 2h including gas chromatography-mass (GC-MS) spectrometry analysis. The limits of quantification vary in a range of 0.8 to 38 ng/L.

Pan-European survey on the occurrence of selected polar organic persistent pollutants in ground water.

This study provides the first pan-European reconnaissance of the occurrence of polar organic persistent pollutants in European ground water. In total, 164 individual ground-water samples from 23 European Countries were collected and analysed (among others) for 59 selected organic compounds, comprising pharmaceuticals, antibiotics, pesticides (and their transformation products), perfluorinated acids (PFAs), benzotriazoles, hormones, alkylphenolics (endocrine disrupters), Caffeine, Diethyltoluamide (DEET), and Triclosan. The most relevant compounds in terms of frequency of detection and maximum concentrations detected were DEET (84%; 454 ng/L), Caffeine (83%; 189 ng/L), PFOA (66%; 39 ng/L), Atrazine (56%; 253 ng/L), Desethylatrazine (55%; 487 ng/L), 1H-Benzotriazole (53%; 1032 ng/L), Methylbenzotriazole (52%; 516 ng/L), Desethylterbutylazine (49%; 266 ng/L), PFOS (48%, 135 ng/L), Simazine (43%; 127 ng/L), Carbamazepine (42%; 390 ng/L), nonylphenoxy acetic acid (NPE(1)C) (42%; 11 microg/L), Bisphenol A (40%; 2.3 microg/L), PFHxS (35%; 19 ng/L), Terbutylazine (34%; 716 ng/L), Bentazone (32%; 11 microg/L), Propazine (32%; 25 ng/L), PFHpA (30%; 21 ng/L), 2,4-Dinitrophenol (29%; 122 ng/L), Diuron (29%; 279 ng/L), and Sulfamethoxazole (24%; 38 ng/L). The chemicals which were detected most frequently above the European ground water quality standard for pesticides of 0.1 microg/L were Chloridazon-desphenyl (26 samples), NPE(1)C (20), Bisphenol A (12), Benzotriazole (8), N,N'-Dimethylsulfamid (DMS) (8), Desethylatrazine (6), Nonylphenol (6), Chloridazon-methyldesphenyl (6), Methylbenzotriazole (5), Carbamazepine (4), and Bentazone (4). However, only 1.7% of all single analytical measurements (in total 8000) were above this threshold value of 0.1 microg/L; 7.3% were > than 10 ng/L.

Total concentration analysis of polycylic aromatic hydrocarbons in aqueous samples with high suspended particulate matter content.

The European water framework directive (WFD) requires priority pollutants to be measured in the whole water sample and not only in the dissolved phase. However, it does not give clear definitions on how to achieve this. To overcome this limitation, a new methodology of sample preparation procedure for the analysis of polycyclic aromatic hydrocarbons on the basis of extraction disks is introduced here. The automatable procedure includes a "one-step" extraction of the analytes both dissolved in the liquid phase of the sample and sorbed to suspended particulate matter. The latter is extracted concurrently with the solid-phase extraction (SPE) material within the elution step of the procedure. Separation, identification, and quantification of the analytes is performed by GC-MS. Results from surface water samples spiked with certified sediment up to 1000 mg/l are presented in this work and compared with results derived from liquid-liquid extraction (LLE). Most measured values are within or at least near certified uncertainty limits of the sediment. The SPE disk method shows much higher recoveries and better precision (relative standard deviations between 2% and 11%) than the standard LLE method. For all substances under investigation, the limits of quantification achieved range between 0.001 and 0.005 microg/l.