Improving the reliability of the iron concentration quantification for iron oxide nanoparticle suspensions: a two-institutions study.

Most iron oxide nanoparticles applications, and in special biomedical applications, require the accurate determination of iron content as the determination of particle properties from measurements in dispersions is strongly dependent on it. Inductively coupled plasma (ICP) and spectrophotometry are two typical worldwide used analytical methods for iron concentration determination. In both techniques, precise determination of iron is not straightforward and nanoparticle digestion and dilution procedures are needed prior to analysis. The sample preparation protocol has been shown to be as important as the analytical method when accuracy is aimed as many puzzling reported results in magnetic, colloidal, and structural properties are simply attributable to inadequate dissolution procedures. Therefore, a standard sample preparation protocol is needed to ensure the adequate and complete iron oxide nanoparticle dissolution and to harmonize this procedure. In this work, an interlaboratory evaluation of an optimized iron oxide nanoparticle digestion/dilution protocol was carried out. The presented protocol is simple, inexpensive, and does not involve any special device (as microwave, ultrasound, or other high-priced digestion devices). Then, iron concentration was measured by ICP-OES (performed in ICMM/CSIC-Spain) and spectrophotometry (NanoPET-Germany) and the obtained concentration values were analyzed to determine the most probable error causes. Uncertainty values as low as 1.5% were achieved after the optimized method was applied. Moreover, this article provides a list of recommendations to significantly reduce uncertainty in both sample preparation and analysis procedures. Graphical abstract ᅟ.

Synthesis and functionalisation of magnetic nanoparticles for hyperthermia applications.

A summary of recent developments in the synthesis, stabilisation and coating of magnetic iron oxide nanoparticles for hyperthermia applications is presented. Methods for synthesis in aqueous, organic and microemulsion systems are reviewed together with the resulting heating rates of the nanoparticles. Different stabilisation mechanisms for iron oxide nanoparticles from aqueous and organic media are discussed as intermediates for further coating and functionalisation. Coating with silica and/or polysaccharides is mainly used for design of nanoparticles especially for targeted hyperthermia application. These coatings permit versatile functionalisation as a basis for conjugating biomolecules, e.g. antibodies or peptides. Various strategies to conjugate biomolecules on the particle surface are discussed, with emphasis on methods that preserve biofunctionality after immobilisation. The efficiency of established methods such as carbodiimide coupling and oriented conjugation strategies is compared with new developments such as the bioorthogonal approaches that are based on the cycloaddition of strain-promoted alkynes with azides or nitrones. For targeted hyperthermia applications the study of the formation of a protein corona around nanoparticles with site-specific biomolecules on the surface is essential to achieve improved circulation times in the blood and reduced non-specific uptake by non-targeted organs for a high specific accumulation in the target tissue.

Physical characterization and in vivo organ distribution of coated iron oxide nanoparticles.

Citrate-stabilized iron oxide magnetic nanoparticles (MNPs) were coated with one of carboxymethyl dextran (CM-dextran), polyethylene glycol-polyethylene imine (PEG-PEI), methoxy-PEG-phosphate+rutin, or dextran. They were characterized for size, zeta potential, hysteresis heating in an alternating magnetic field, dynamic magnetic susceptibility, and examined for their distribution in mouse organs following intravenous delivery. Except for PEG-PEI-coated nanoparticles, all coated nanoparticles had a negative zeta potential at physiological pH. Nanoparticle sizing by dynamic light scattering revealed an increased nanoparticle hydrodynamic diameter upon coating. Magnetic hysteresis heating changed little with coating; however, the larger particles demonstrated significant shifts of the peak of complex magnetic susceptibility to lower frequency. 48 hours following intravenous injection of nanoparticles, mice were sacrificed and tissues were collected to measure iron concentration. Iron deposition from nanoparticles possessing a negative surface potential was observed to have highest accumulation in livers and spleens. In contrast, iron deposition from positively charged PEG-PEI-coated nanoparticles was observed to have highest concentration in lungs. These preliminary results suggest a complex interplay between nanoparticle size and charge determines organ distribution of systemically-delivered iron oxide magnetic nanoparticles.

Quantification of blood group A and B antibodies by flow cytometry using beads carrying A or B trisaccharides.

In the clinical management of patients receiving blood group ABO-incompatible organ allografts, it is of importance to determine the levels of blood group A and B antibodies before and after transplant. Currently used methods, which are mostly based on hemagglutination, are inexact and are associated with large intercenter variations. Here, we describe preliminary data from our efforts to establish a flow cytometry-based assay for the semiquantification of blood group A and B antibodies using beads carrying synthetic A or B trisaccharides. In agreement with previous investigations, blood group O individuals had greater levels of anti-A immunoglobulin G (IgG) than B individuals, whereas the levels of anti-A immunoglobulin M (IgM) were similar in sera from blood group O and B individuals.

Stem cell labeling with iron oxide nanoparticles: impact of 3D culture on cell labeling maintenance.

AIM: We aimed to analyze the suitability of nanoparticles (M4E) for safe human mesenchymal stem cell (hMSC) labeling and determined cell labeling maintenance in 2D and 3D culture. MATERIALS & METHODS: We investigated cell-particle interaction and the particles' impact on cell viability, growth and proliferation. We analyzed cell labeling maintenance in 2D and 3D culture invasively and noninvasively. RESULTS: M4E do not affect cell viability, growth and proliferation and do not cause chromosomal aberrations. Cell labeling maintenance is up to five-times higher in 3D conditions compared with 2D culture. CONCLUSION: M4E allow safe hMSC labeling and noninvasive identification. Our hMSC-loaded, 3D tissue-engineered construct could serve as a graft for regenerative therapies, in which M4E-labeled hMSCs can migrate to their target.

The effect of cell cluster size on intracellular nanoparticle-mediated hyperthermia: is it possible to treat microscopic tumors?

AIM: To compare the measured surface temperature of variable size ensembles of cells heated by intracellular magnetic fluid hyperthermia with heat diffusion model predictions. MATERIALS & METHODS: Starch-coated Bionized NanoFerrite (Micromod Partikeltechnologie GmbH, Rostock, Germany) iron oxide magnetic nanoparticles were loaded into cultured DU145 prostate cancer cells. Cell pellets of variable size were treated with alternating magnetic fields. The surface temperature of the pellets was measured in situ and the associated cytotoxicity was determined by clonogenic survival assay. RESULTS & CONCLUSION: For a given intracellular nanoparticle concentration, a critical minimum number of cells was required for cytotoxic hyperthermia. Above this threshold, cytotoxicity increased with increasing cell number. The measured surface temperatures were consistent with those predicted by a heat diffusion model that ignores intercellular thermal barriers. These results suggest a minimum tumor volume threshold of approximately 1 mm(3), below which nanoparticle-mediated heating is unlikely to be effective as the sole cytotoxic agent.