A Pilot Experiment to Measure the Initial Mechanical Stability of the Femoral Head Implant in a Cadaveric Model of Osteonecrosis of Femoral Head Involving up to 50% of the Remaining Femoral Head.

Background and Objectives: Currently, only patients with osteonecrosis of the femoral head (ONFH), who had bone defects involving 30-33.3% of the remaining femoral head, are indicated in hip resurfacing arthroplasty (HRA). In an experimental cadaver model of ONFH involving up to 50% of the remaining femoral head, the initial stability of the femoral head implant (FHI) at the interface between the implant and the remaining femoral head was measured. Materials and Methods: The ten specimens and the remaining ten served as the experimental group and the control group, respectively. We examined the degree of the displacement of the FHI, the bonding strength between the FHI and the retained bone and that at the interface between the FHI and bone cement. Results: Changes in the degree of displacement at the final phase from the initial phase were calculated as 0.089 ± 0.036 mm in the experimental group and 0.083 ± 0.056 mm in the control group. However, this difference reached no statistical significance (p = 0.7789). Overall, there was an increase in the degree of displacement due to the loading stress, with increased loading cycles in both groups. In cycles of up to 6000 times, there was a steep increase. After cycles of 8000 times, however, there was a gradual increase. Moreover, in cycles of up to 8000 times, there was an increase in the difference in the degree of displacement due to the loading stress between the two groups. After cycles of 8000 times, however, such difference remained almost unchanged. Conclusions: In conclusion, orthopedic surgeons could consider performing the HRA in patients with ONFH where the bone defects involved up to 50% of the remaining femoral head, without involving the femoral head-neck junction in the anterior and superior area of the femoral head. However, more evidence-based studies are warranted to justify our results.

Intramedullary fixation of metacarpal and phalangeal bone fractures with bioabsorbable Mg K-wire in 20 cases.

PURPOSE: The treatment of irreducible or severely displaced metacarpal and phalangeal bone fractures is still much debated. The recent development of the bioabsorbable magnesium K-wire is thought to allow effective treatment upon insertion via intramedullary fixation by minimizing articular cartilage injuries without discomfort until pin removal and drawbacks, such as pin track infection and metal plate removal. Therefore, this study investigated and reported the effects of intramedullary fixation with the bioabsorbable magnesium K-wire in unstable metacarpal and phalangeal bone fractures. METHODS: This study included 19 patients admitted to our clinic for metacarpal or phalangeal bone fractures from May 2019 to July 2021. As a result, 20 cases were examined among these 19 patients. RESULTS: Bone union was observed in all 20 cases, with a mean bone union time of 10.5 (SD 3.4) weeks. Reduction loss was observed in six cases, all showing dorsal angulation with a mean angle of 6.6° (SD 3.5°) at 4.6 weeks as compared with that noted in the unaffected side. The gas cavity upon H2 gas formation was first observed approximately 2 weeks postoperatively. The mean DASH score was 33.5 for instrumental activity and 9.5 for work/task performance. No patient complained of notable discomfort after surgery. CONCLUSION: Intramedullary fixation with the bioabsorbable magnesium K-wire may be used for unstable metacarpal and phalanx bone fractures. This wire is expected to be a particularly favorable indication for shaft fractures, although care should be taken due to the possibility of complications related to rigidity and deformity.

Results of the Use of Bioabsorbable Magnesium Screws for Surgical Treatment of Mason Type II Radial Head Fractures.

Background: In Mason classification type II radial head fractures, compared to plate fixation, fixation with cannulated headless screws and absorbable pins has been reported to provide more favorable postoperative outcomes, including less postoperative limitation in range of motion. The fact that radial head fractures are less prone to weight-bearing during fracture union further supports the use of absorbable screws as a suitable alternative treatment option in radial head fractures. This study aimed to perform fixation through open reduction using bioabsorbable magnesium screws for Mason type II radial head fractures and to report radiographic and clinical results. Methods: Among patients who visited the orthopedic department from April 2017 to August 2021, 22 with surgical indications were selected for participation. Radiographic tests were conducted at 2 weeks, 4 weeks, 8 weeks, 12 weeks, 6 months, and over 1 year after surgery to confirm the degree of bone union, reduction loss, and degree of H2 gas production. The Disabilities of the Arm, Shoulder and Hand (DASH) score, Mayo Elbow Performance Score (MEPS), hand grip power, and range of joint motion were measured at the 6-month follow-up to evaluate the clinical efficacy of the operation. Results: Bone union was confirmed in all 22 cases, and the mean time to union was 10.2 weeks. DASH score was 22.27 on average and no patients complained of significant discomfort after the surgery. The mean MEPS was 91.1. The hand grip power of the affected hand was similar to that of the unaffected hand, being 1.19% weaker on average. These differences reached statistical significance (p = 0.002). The range of elbow joint motion was measured: mean flexion, 146.1°; mean extension, 1.4°; mean pronation, 88.2°; and mean supination, 87.9°. Conclusions: In treating Mason type II radial head fractures, the use of bioabsorbable screws made of magnesium showed satisfactory results in radiographic and clinical evaluations. Magnesium bioabsorbable screws can maintain sufficient stability at the fracture site and have the advantage of avoiding secondary operation for the removal of internal fixation devices.