Development of Cu-In-Ga-S quantum dots with a narrow emission peak for red electroluminescence.

Narrowing the emission peak width and adjusting the peak position play a key role in the chromaticity and color accuracy of display devices with the use of quantum dot light-emitting diodes (QD-LEDs). In this study, we developed multinary Cu-In-Ga-S (CIGS) QDs showing a narrow photoluminescence (PL) peak by controlling the Cu fraction, i.e., Cu/(In+Ga), and the ratio of In to Ga composing the QDs. The energy gap of CIGS QDs was enlarged from 1.74 to 2.77 eV with a decrease in the In/(In+Ga) ratio from 1.0 to 0. The PL intensity was remarkably dependent on the Cu fraction, and the PL peak width was dependent on the In/(In+Ga) ratio. The sharpest PL peak at 668 nm with a full width at half maximum (fwhm) of 0.23 eV was obtained for CIGS QDs prepared with ratios of Cu/(In+Ga) = 0.3 and In/(In+Ga) = 0.7, being much narrower than those previously reported with CIGS QDs, fwhm of >0.4 eV. The PL quantum yield of CIGS QDs, 8.3%, was increased to 27% and 46% without a PL peak broadening by surface coating with GaSx and Ga-Zn-S shells, respectively. Considering a large Stokes shift of >0.5 eV and the predominant PL decay component of ∼200-400 ns, the narrow PL peak was assignable to the emission from intragap states. QD-LEDs fabricated with CIGS QDs surface-coated with GaSx shells showed a red color with a narrow emission peak at 688 nm with a fwhm of 0.24 eV.

Visualization of airborne droplets generated with dental handpieces and verification of the efficacy of high-volume evacuators: an in vitro study.

BACKGROUND: The COVID-19 pandemic led to concerns about the potential airborne transmission of the virus during dental procedures, but evidence of actual transmission in clinical settings was lacking. This study aimed to observe the behavior of dental sprays generated from dental rotary handpieces and to evaluate the effectiveness of high-volume evacuators (HVEs) using laser light sheets and water-sensitive papers. METHODS: A dental manikin and jaw model were mounted in a dental treatment unit. Mock cutting procedures were performed on an artificial tooth on the maxillary left central incisor using an air turbine, a contra-angle electric micromotor (EM), and a 1:5 speed-up contra-angle EM (×5EM). Intraoral vacuum and extraoral vacuum (EOV) were used to verify the effectiveness of the HVEs. The dynamics and dispersal range of the dental sprays were visualized using a laser light sheet. In addition, environmental surface pollution was monitored three-dimensionally using water-sensitive papers. RESULTS: Although the HVEs were effective in both the tests, the use of EOV alone increased vertical dispersal and pollution. CONCLUSIONS: The use of various types of HVEs to reduce the exposure of operators and assistants to dental sprays when using dental rotary cutting instruments is beneficial. The study findings will be helpful in the event of a future pandemic caused by an emerging or re-emerging infectious disease.

[Challenges Faced by the Palliative Care Team in Treating Breast Cancer Outpatients with Chemotherapy].

In this study, we examined 239 outpatients receiving chemotherapy for breast cancer for a period of 6 months from July 2016 to December 2016. Using a questionnaire, we investigated the patients' symptom score and uneasiness. A symptom score of 2 and over was found in 24.7%(59)of the cases. Twenty-seven of the 59 cases experienced adverse effects of chemotherapy. Peripheral neuropathy was observed in 20 cases, of which only 2 cases improved after providing palliative care. Palliative care was effective against nausea, constipation, malaise, and sleeping disorders. Thirty-two cases(13.4%)had 5 or more painful feeling score. Among these, 10 cases resulted from the adverse effects of treatment, 10 cases from the aggravation of existing cancer, and 6 cases showed anxiety for the illness, family, and future. In 15 of the 32 cases, the pain score improved by providing palliative care, conversation with the nursing staff, reduction in the quantity of drug intake, etc.

Molecular Encapsulation Inside Microtubules Based on Tau-Derived Peptides.

Microtubules are cytoskeletal filaments that serve as attractive scaffolds for developing nanomaterials and nanodevices because of their unique structural properties. The functionalization of the outer surface of microtubules has been established for this purpose. However, no attempts have been made to encapsulate molecules inside microtubules with 15 nm inner diameter. The encapsulation of various molecular cargos inside microtubules constitutes a new concept for nanodevice and nanocarrier applications of microtubules. Here, we developed peptide motifs for binding to the inner surface of microtubules, based on a repeat domain of the microtubule-associated protein Tau. One of the four Tau-derived peptides, 2N , binds to a taxol binding pocket of ß-tubulin located inside microtubules by preincubation with tubulin dimer and subsequent polymerization of the peptide-tubulin complex. By conjugation of 2N to gold nanoparticles, encapsulation of gold nanoparticles inside microtubules was achieved. The methodology for molecular encapsulation inside microtubules by the Tau-derived peptide is expected to advance the development of microtubule-based nanomaterials and nanodevices.

Replacement of SFC-DPI with SFC-MDI exhaled through the nose improves eosinophilic chronic rhinosinusitis in patients with bronchial asthma.

OBJECTIVE: Eosinophilic chronic rhinosinusitis (ECRS), a subgroup of chronic rhinosinusitis with nasal polyps, is a refractory disease closely associated with bronchial asthma. We recently reported on the efficacy of ultra-fine particle inhaled corticosteroids (ICS) (hydrofluoroalkane-134a-beclomethasone dipropionate: HFA-BDP) exhalation through the nose (ETN) treatment for mild-to-moderate asthmatics with ECRS. However, the effect of HFA-BDP ETN was found to be transient in some cases with severe ECRS and asthma, requiring treatment with higher-dose ICS and long-acting ß2-agonists (LABA). Here, we present a case of refractory ECRS with severe asthma treated with a combination of high-dose ICS and LABA ETN, and we discuss the mechanisms for its effectiveness. METHODS: A 57-year-old man was treated with the combined regimen of HFA-BDP ETN and salmeterol/fluticasone combination (SFC) dry powder inhaler (DPI) for his refractory ECRS with severe asthma. For better control, we replaced SFC-DPI with SFC metered-dose inhaler (MDI) ETN and evaluated the clinical effect and corticosteroid sensitivity. We also examined the flow and deposition of fine particles released by SFC-MDI ETN. RESULTS: After switching to SFC-MDI ETN, the patient's conditions markedly resolved with the restoration of corticosteroid sensitivity and PP2A activity. The fine particles released by SFC-MDI ETN at least partially flowed out through the external nares and seemed to be deposited on the ethmoid sinus. CONCLUSION: Fine particle ICS/LABA ETN might be an additional therapeutic option for refractory ECRS with severe asthma and corticosteroid insensitivity.
.

Assessment of Strain-Generated Oxygen Vacancies Using SrTiO3 Bicrystals.

Atomic-scale defects strongly influence the electrical and optical properties of materials, and their impact can be more pronounced in localized dimensions. Here, we directly demonstrate that strain triggers the formation of oxygen vacancies in complex oxides by examining the tilt boundary of SrTiO3 bicrystals. Through transmission electron microscopy and electron energy loss spectroscopy, we identify strains along the tilt boundary and oxygen vacancies in the strain-imposed regions between dislocation cores. First-principles calculations support that strains, irrespective of their type or sign, lower the formation energy of oxygen vacancies, thereby enhancing vacancy formation. Finally, current-voltage measurements confirm that such oxygen vacancies at the strained boundary result in a decrease of the nonlinearity of the I-V curve as well as the resistivity. Our results strongly indicate that oxygen vacancies are preferentially formed and are segregated at the regions where strains accumulate, such as heterogeneous interfaces and grain boundaries.

[Empyema from spontaneous esophageal rupture treated by thoracoscopic surgery].

A 61-year-old man who had been admitted for vomiting and abdominal pain 5 days before at another hospital was transferred to our hospital. He was diagnosed as pyo-pneumothorax, and chest drainage was initiated. Seven days after admission, food residue was observed in the drainage tube. A subsequent gastrointestinal fiberscopic examination could not identify the esophageal injury, but the acute empyema caused by spontaneous esophageal rupture was suggested by clinical signs. Thoracoscopic surgery for curettage and irrigation of the pleural cavity was performed. Esophageal rupture could not be confirmed at surgery. Spontaneous closure of the fistula was observed 2 weeks post-surgery.

One-pot synthesis of Ag-In-Ga-S nanocrystals embedded in a Ga2O3 matrix and enhancement of band-edge emission by Na+ doping.

I-III-VI-based semiconductor quantum dots (QDs) have been intensively explored because of their unique controllable optoelectronic properties. Here we report one-pot synthesis of Na-doped Ag-In-Ga-S (AIGS) QDs incorporated in a Ga2O3 matrix. The obtained QDs showed a sharp band-edge photoluminescence peak at 557 nm without a broad-defect site emission. The PL quantum yield (QY) of such QDs was 58%, being much higher than that of AIGS QDs without Na+ doping, 29%. The obtained Na-doped AIGS/Ga2O3 composite particles were used as an emitting layer of green QD light-emitted diodes. A sharp electroluminescence (EL) peak was observed at 563 nm, being similar to that in the PL spectrum of the QDs used. The external quantum efficiency of the device was 0.6%.

Temperature distributions of electron beam-irradiated samples by scanning electron microscopy.

An electron beam (EB) generated by a scanning electron microscope (SEM) was used to irradiate two samples having different thermal conductivities, and the resulting temperatures of the EB-irradiated areas as well as the temperature distributions within the samples were then measured using a thermal camera. These measurements showed overall increases in sample temperatures, as well as revealed temperature rises at the EB-irradiated areas that had little difference with one of the theoretical predictions. Differences between the actual and the predicted temperature measurements were analysed in terms of the accuracy with which parameters could be estimated. The temperature distributions of the samples were measured and, On the basis of the results, it was hypothesized that the temperature differential over an irradiated sample will be inversely correlated with its thermal conductivity.

A method for accurate temperature measurement using infrared thermal camera.

The temperature distribution on a centre-holed thin foil of molybdenum, used as a sample and heated using a sample-heating holder for electron microscopy, was measured using an infrared thermal camera. The temperature on the heated foil area located near the heating stage of the heating holder is almost equal to the temperature on the heating stage. However, during the measurement of the temperature at the edge of the hole of the foil located farthest from the heating stage, a drop in temperature should be taken into consideration; however, so far, no method has been developed to locally measure the temperature distribution on the heated sample. In this study, a method for the accurate measurement of temperature distribution on heated samples for electron microscopy is discussed.

Tensile strength of nanocrystalline FeCoNi medium-entropy alloy fabricated using electrodeposition.

Crystal-grain refinement is one of the effective approaches to obtaining high-strength materials. A good strength/ductility balance has been reported in fine grains of high- and medium-entropy alloys. However, crystal-grain refinement at the nanometer scale has not been achieved yet. In this study, we used electrodeposition to fabricate 0.2-mm thick equiatomic FeCoNi medium-entropy alloys (MEAs) with 10-nm crystal grains. The nanocrystalline FeCoNi MEAs exhibit the maximum tensile strength of 1.6 GPa, which is the highest reported result to date.

Effect of electron beam irradiation in gas atmosphere during ETEM.

Transmission electron microscopy (TEM) is used to observe the atomic structures of materials. Environmental TEM (ETEM) is a method wherein a gas can be evaluated and it has been used to observe the dynamic reaction between materials and gases at the atomic level. An electron beam (EB), which has a sufficiently high energy (exceeding a few tens of kilovolts), can be used to ionize gas molecules. Subsequently, the ionized molecules might react with the materials during ETEM. Therefore, the current generated by the ions and electrons were measured to verify the presence of ions generated due to the ionization of the N2 gas atmosphere during EB irradiation in ETEM. The electron energy loss spectra (EELS) were acquired from the N2 gas atmosphere to estimate the types of ions generated. The results demonstrated that ions and electrons were generated in the N2 atmosphere during ETEM and EB irradiation. Moreover, the EELS analysis indicated that the generated ion was N2+. The material observation conducted using gas ETEM can detect the reaction between gases, ions, and materials.

Atomic structure of a CeO2 grain boundary: the role of oxygen vacancies.

Determining both cation and oxygen sublattices of grain boundaries is essential to understand the properties of oxides. Here, with scanning transmission electron microscopy, electron energy-loss spectroscopy, and first-principles calculations, both the Ce and oxygen sublattices of a (210)Σ5 CeO(2) grain boundary were determined. Oxygen vacancies are shown to play a crucial role in the stable grain boundary structure. This finding paves the way for a comprehensive understanding of grain boundaries through the atomic scale determination of atom and defect locations.

Dislocation structures and strain fields in [111] low-angle tilt grain boundaries in zirconia bicrystals.

Structures of <111> low-angle tilt grain boundaries in yttria-stabilized cubic zirconia bicrystals were characterized by conventional transmission electron microscopy, high-resolution transmission electron microscopy and high-angle annular dark-field scanning transmission electron microscopy. It is found that the 0.4 and 4.0 degrees tilt grain boundaries are composed of periodic arrays of edge dislocations with Burgers vectors . The experimentally estimated strain field of each dislocation in the 0.4 degrees tilt boundary was in good agreement with the theoretically predicted strain field from the Peierls-Nabarro model. On the other hand, the estimated strain field of each dislocation in the 4.0 degrees tilt boundary was clearly different from that in the 0.4 degrees tilt boundary, which suggests that the strain fields of neighbouring dislocations interact when the separation distance between dislocations is shorter than a critical value.

Microstructural heterogeneity in the electrodeposited Ni: insights from growth modes.

Microstructures of electrodeposited Ni were studied from the perspective of growth modes during electrodeposition. The electrodeposited Ni had a heterogeneous microstructure composed of nanocrystalline- and microcrystalline-grains. Electron backscatter diffraction analyses showed that nanocrystalline- and microcrystalline-grains were preferentially oriented to specific planes. Secondary ion mass spectrometry also revealed that coarse-grained regions had higher S content than that of finer-grained regions. Hence, microstructural heterogeneity in electrodeposited Ni is reflected by the overlap of inhibited and free growth modes. Our discussion surrounding microstructural heterogeneity also provides insight into other electrodeposited nanocrystalline systems.

Controlling the oxidation state of molybdenum oxide nanoparticles prepared by ionic liquid/metal sputtering to enhance plasmon-induced charge separation.

Nanoparticles composed of molybdenum oxide, MoO x , were successfully prepared by room-temperature ionic liquid (RTIL)/metal sputtering followed by heat treatment. Hydroxyl groups in RTIL molecules retarded the coalescence between MoO x NPs during heat treatment at 473 K in air, while the oxidation state of Mo species in MoO x nanoparticles (NPs) could be modified by changing the heat treatment time. An LSPR peak was observed at 840 nm in the near-IR region for MoO x NPs of 55 nm or larger in size that were annealed in a hydroxyl-functionalized RTIL. Photoexcitation of the LSPR peak of MoO x NPs induced electron transfer from NPs to ITO electrodes.

Core Nanoparticle Engineering for Narrower and More Intense Band-Edge Emission from AgInS2/GaSx Core/Shell Quantum Dots.

Highly luminescent silver indium sulfide (AgInS2) nanoparticles were synthesized by dropwise injection of a sulfur precursor solution into a cationic metal precursor solution. The two-step reaction including the formation of silver sulfide (Ag2S) nanoparticles as an intermediate and their conversion to AgInS2 nanoparticles, occurred during the dropwise injection. The crystal structure of the AgInS2 nanoparticles differed according to the temperature of the metal precursor solution. Specifically, the tetragonal crystal phase was obtained at 140 °C, and the orthorhombic crystal phase was obtained at 180 °C. Furthermore, when the AgInS2 nanoparticles were coated with a gallium sulfide (GaSx) shell, the nanoparticles with both crystal phases emitted a spectrally narrow luminescence, which originated from the band-edge transition of AgInS2. Tetragonal AgInS2 exhibited narrower band-edge emission (full width at half maximum, FWHM = 32.2 nm) and higher photoluminescence (PL) quantum yield (QY) (49.2%) than those of the orthorhombic AgInS2 nanoparticles (FWHM = 37.8 nm, QY = 33.3%). Additional surface passivation by alkylphosphine resulted in higher PL QY (72.3%) with a narrow spectral shape.

Fluorescent Tau-derived Peptide for Monitoring Microtubules in Living Cells.

Microtubules (MTs) are key cytoskeletal components that modulate various cellular activities with their dynamic structural changes, including polymerization and depolymerization. To monitor the dynamics of MTs in living cells, many drug-based fluorescent probes have been developed; however, these also potentially disturb the polymerization/depolymerization of MTs. Here, we report nondrug, peptide-based fluorescent probes to monitor MTs in living cells. We employed a Tau-derived peptide (TP) that has been shown to bind MTs without inhibiting polymerization/depolymerization in vitro. We show that a tetramethylrhodamine (TMR)-labeled TP (TP-TMR) is internalized into HepG2 cells and binds to intracellular MTs, enabling visualization of MTs as clear, fibrous structures. The binding of TP-TMR shows no apparent effects on polymerization/depolymerization of MTs induced by MT-targeted drugs and temperature change. The main uptake mechanism of TP-TMR was elucidated as endocytosis, and partial endosomal escape resulted in the binding of TP-TMR to MTs. TP-TMR exhibited no cytotoxicity compared with MT-targeted drug scaffolds. These results indicate that TP scaffolds can be exploited as useful MT-targeted tools in living cells, such as in long-term imaging of MTs.

Stabilization of microtubules by encapsulation of the GFP using a Tau-derived peptide.

We constructed GFP-encapsulated microtubules (MTs) using a Tau-derived peptide which binds to their interior. The encapsulation of the GFP dramatically increased the rigidity of MTs, resulting in their enhanced velocity on a kinesin-coated substrate. Moreover, the GFP-encapsulated MTs were significantly more stable than normal MTs.

Growth mechanism and internal structure of vertically aligned single-walled carbon nanotubes.

An in situ optical absorbance technique was used to monitor the growth of vertically aligned single-walled carbon nanotubes (VA-SWNTs) at various temperatures and pressures. The effects of the growth temperature and ethanol pressure on the initial growth rate and catalyst lifetime were investigated. It was found that the ideal pressure for VA-SWNT synthesis changes with the growth temperature, shifting toward higher pressure as the growth temperature increases. It was also found that the growth reaction is first-order below this ideal pressure. Additionally, the internal structure of the VA-SWNT film was observed at different depths into the film by transmission electron microscopy. The absence of large bundles was confirmed, and little change in the structure was observed to a depth of approximately 1 microm.