From O2- to HO2- : Reducing By-Products and Overpotential in Li-O2 Batteries by Water Addition.

The development of aprotic Li-O2 batteries, which are promising candidates for high gravimetric energy storage devices, is severely limited by superoxide-related parasitic reactions and large voltage hysteresis. The fundamental reaction pathway of the aprotic Li-O2 battery can be altered by the addition of water, which changes the discharge intermediate from superoxide (O2- ) to hydroperoxide (HO2- ). The new mechanism involving HO2- intermediate realizes the two-electron transfer through a single step, which significantly suppresses the superoxide-related side reactions. Moreover, addition of water also triggers a solution-based pathway that effectively reduces the voltage hysteresis. These discoveries offer a possible solution for desirable Li-O2 batteries free of aggressive superoxide species, highlighting the design strategy of modifying the reaction pathway for Li-O2 electrochemistry.

A solid-state lithium-ion battery with micron-sized silicon anode operating free from external pressure.

Applying high stack pressure (often up to tens of megapascals) to solid-state Li-ion batteries is primarily done to address the issues of internal voids formation and subsequent Li-ion transport blockage within the solid electrode due to volume changes. Whereas, redundant pressurizing devices lower the energy density of batteries and raise the cost. Herein, a mechanical optimization strategy involving elastic electrolyte is proposed for SSBs operating without external pressurizing, but relying solely on the built-in pressure of cells. We combine soft-rigid dual monomer copolymer with deep eutectic mixture to design an elastic solid electrolyte, which exhibits not only high stretchability and deformation recovery capability but also high room-temperature Li-ion conductivity of 2×10-3 S cm-1 and nonflammability. The micron-sized Si anode without additional stack pressure, paired with the elastic electrolyte, exhibits exceptional stability for 300 cycles with 90.8% capacity retention. Furthermore, the solid Li/elastic electrolyte/LiFePO4 battery delivers 143.3 mAh g-1 after 400 cycles. Finally, the micron-sized Si/elastic electrolyte/LiFePO4 full cell operates stably for 100 cycles in the absence of any additional pressure, maintaining a capacity retention rate of 98.3%. This significantly advances the practical applications of solid-state batteries.

Diagnosing the Electrostatic Shielding Mechanism for Dendrite Suppression in Aqueous Zinc Batteries.

Aqueous zinc electrolytes offer the potential for cheaper rechargeable batteries due to their safe compatibility with the high capacity metal anode; yet, they are stymied by irregular zinc deposition and consequent dendrite growth. Suppressing dendrite formation by tailoring the electrolyte is a proven approach from lithium batteries; yet, the underlying mechanistic understanding that guides such tailoring does not necessarily directly translate from one system to the other. Here, it is shown that the electrostatic shielding mechanism, a fundamental concept in electrolyte engineering for stable metal anodes, has different consequences for the plating morphology in aqueous zinc batteries. Operando electrochemical transmission electron microscopy is used to directly observe the zinc nucleation and growth under different electrolyte compositions and reveal that electrostatic shielding additive suppresses dendrites by inhibiting secondary zinc nucleation along the (100) edges of existing primary deposits and encouraging preferential deposition on the (002) faces, leading to a dense and block-like zinc morphology. The strong influence of the crystallography of Zn on the electrostatic shielding mechanism is further confirmed with Zn||Ti cells and density functional theory modeling. This work demonstrates the importance of considering the unique aspects of the aqueous zinc battery system when using concepts from other battery chemistries.

Binuclear Cu complex catalysis enabling Li-CO2 battery with a high discharge voltage above 3.0 V.

Li-CO2 batteries possess exceptional advantages in using greenhouse gases to provide electrical energy. However, these batteries following Li2CO3-product route usually deliver low output voltage (<2.5 V) and energy efficiency. Besides, Li2CO3-related parasitic reactions can further degrade battery performance. Herein, we introduce a soluble binuclear copper(I) complex as the liquid catalyst to achieve Li2C2O4 products in Li-CO2 batteries. The Li-CO2 battery using the copper(I) complex exhibits a high electromotive voltage up to 3.38 V, an increased output voltage of 3.04 V, and an enlarged discharge capacity of 5846 mAh g-1. And it shows robust cyclability over 400 cycles with additional help of Ru catalyst. We reveal that the copper(I) complex can easily capture CO2 to form a bridged Cu(II)-oxalate adduct. Subsequently reduction of the adduct occurs during discharge. This work innovatively increases the output voltage of Li-CO2 batteries to higher than 3.0 V, paving a promising avenue for the design and regulation of CO2 conversion reactions.

Why charging Li-air batteries with current low-voltage mediators is slow and singlet oxygen does not explain degradation.

Although Li-air rechargeable batteries offer higher energy densities than lithium-ion batteries, the insulating Li2O2 formed during discharge hinders rapid, efficient re-charging. Redox mediators are used to facilitate Li2O2 oxidation; however, fast kinetics at a low charging voltage are necessary for practical applications and are yet to be achieved. We investigate the mechanism of Li2O2 oxidation by redox mediators. The rate-limiting step is the outer-sphere one-electron oxidation of Li2O2 to LiO2, which follows Marcus theory. The second step is dominated by LiO2 disproportionation, forming mostly triplet-state O2. The yield of singlet-state O2 depends on the redox potential of the mediator in a way that does not correlate with electrolyte degradation, in contrast to earlier views. Our mechanistic understanding explains why current low-voltage mediators (<+3.3 V) fail to deliver high rates (the maximum rate is at +3.74 V) and suggests important mediator design strategies to deliver sufficiently high rates for fast charging at potentials closer to the thermodynamic potential of Li2O2 oxidation (+2.96 V).

Achieving Ultrahigh-Rate Planar and Dendrite-Free Zinc Electroplating for Aqueous Zinc Battery Anodes.

Despite being one of the most promising candidates for grid-level energy storage, practical aqueous zinc batteries are limited by dendrite formation, which leads to significantly compromised safety and cycling performance. In this study, by using single-crystal Zn-metal anodes, reversible electrodeposition of planar Zn with a high capacity of 8 mAh cm-2 can be achieved at an unprecedentedly high current density of 200 mA cm-2 . This dendrite-free electrode is well maintained even after prolonged cycling (>1200 cycles at 50 mA cm- 2 ). Such excellent electrochemical performance is due to single-crystal Zn suppressing the major sources of defect generation during electroplating and heavily favoring planar deposition morphologies. As so few defect sites form, including those that would normally be found along grain boundaries or to accommodate lattice mismatch, there is little opportunity for dendritic structures to nucleate, even under extreme plating rates. This scarcity of defects is in part due to perfect atomic-stitching between merging Zn islands, ensuring no defective shallow-angle grain boundaries are formed and thus removing a significant source of non-planar Zn nucleation. It is demonstrated that an ideal high-rate Zn anode should offer perfect lattice matching as this facilitates planar epitaxial Zn growth and minimizes the formation of any defective regions.

A low-cost anodic catalyst of transition metal oxides for lithium extraction from seawater.

Lithium reserves in seawater are tens of thousands of times higher than on land, making it a promising candidate for lithium resources. A lithium extraction method based on a solar-powered electrolysis technique with a solid-state electrolyte, Li1.5Al0.5Ge1.5(PO4)3 (LAGP), as the selective membrane has been reported to obtain metallic lithium from seawater. Herein, the electrolytic cell is optimised by replacing the anode catalyst materials. The NiO@SP anode shows excellent electrochemical performance, relatively high energy utilization efficiency and low cost among the anode materials investigated. An electrolytic cell adopting NiO@SP achieves a lithium production efficiency of 57.2 mg W h-1 with a potential of 4.5 V at a current density of 333 µA cm-2. Based on the investigation by in situ mass spectroscopy the oxygen evolution reaction (OER) and chlorine evolution reaction (CER) occur together on the anode with the production of oxygen and hypochlorite.

Organic hydrogen peroxide-driven low charge potentials for high-performance lithium-oxygen batteries with carbon cathodes.

Reducing the high charge potential is a crucial concern in advancing the performance of lithium-oxygen batteries. Here, for water-containing lithium-oxygen batteries with lithium hydroxide products, we find that a hydrogen peroxide aqueous solution added in the electrolyte can effectively promote the decomposition of lithium hydroxide compounds at the ultralow charge potential on a catalyst-free Ketjen Black-based cathode. Furthermore, for non-aqueous lithium-oxygen batteries with lithium peroxide products, we introduce a urea hydrogen peroxide, chelating hydrogen peroxide without any water in the organic, as an electrolyte additive in lithium-oxygen batteries with a lithium metal anode and succeed in the realization of the low charge potential of ∼3.26 V, which is among the best levels reported. In addition, the undesired water generally accompanying hydrogen peroxide solutions is circumvented to protect the lithium metal anode and ensure good battery cycling stability. Our results should provide illuminating insights into approaches to enhancing lithium-oxygen batteries.