Improving interface quality for 1-cm2 all-perovskite tandem solar cells.

All-perovskite tandem solar cells provide high power conversion efficiency at a low cost1-4. Rapid efficiency improvement in small-area (<0.1 cm2) tandem solar cells has been primarily driven by advances in low-bandgap (approximately 1.25 eV) perovskite bottom subcells5-7. However, unsolved issues remain for wide-bandgap (> 1.75 eV) perovskite top subcells8, which at present have large voltage and fill factor losses, particularly for large-area (>1 cm2) tandem solar cells. Here we develop a self-assembled monolayer of (4-(7H-dibenzo[c,g]carbazol-7-yl)butyl)phosphonic acid as a hole-selective layer for wide-bandgap perovskite solar cells, which facilitates subsequent growth of high-quality wide-bandgap perovskite over a large area with suppressed interfacial non-radiative recombination, enabling efficient hole extraction. By integrating (4-(7H-dibenzo[c,g]carbazol-7-yl)butyl)phosphonic acid in devices, we demonstrate a high open-circuit voltage (VOC) of 1.31 V in a 1.77-eV perovskite solar cell, corresponding to a very low VOC deficit of 0.46 V (with respect to the bandgap). With these wide-bandgap perovskite subcells, we report 27.0% (26.4% certified stabilized) monolithic all-perovskite tandem solar cells with an aperture area of 1.044 cm2. The certified tandem cell shows an outstanding combination of a high VOC of 2.12 V and a fill factor of 82.6%. Our demonstration of the large-area tandem solar cells with high certified efficiency is a key step towards scaling up all-perovskite tandem photovoltaic technology.

Doping of ZnO Electron Transport Layer with Organic Dye Molecules to Enhance Efficiency and Photo-Stability of the Non-Fullerene Organic Solar Cells.

The solution-processed zinc oxide (ZnO) electron transport layer (ETL) always exhibits ubiquitous defects, and its photocatalytic activity is detrimental for the organic solar cell (OSC) to achieve high efficiency and stability. Herein, an organic dye molecule, PDINN-S is introduced, to dope ZnO, constructing a hybrid ZnO:PDINN-S ETL. This hybrid ETL exhibits improved electron mobility and conductivity, particularly post-light exposure. The catalytic activity of ZnO is also effectively suppressed.Consequently, the efficiency and photo-stability of inverted non-fullerene OSCs are synergistically enhanced. The devices based on PM6:Y6/PM6:BTP-eC9 active layer with ZnO:PDINN-S as ETL give impressive power conversion efficiencies (PCEs) of 16.78%/17.59%, significantly higher than those with pure ZnO as ETL (PCEs = 15.31%/16.04%). Moreover, ZnO:PDINN-S-based device shows exceptional long-term stability under continuous AM 1.5G illumination (T80 = 1130 h) , overwhelming the reference device (T80 = 455 h). In addition, Incorporating PDINN-S into ZnO alleviate mechanical stress within the inorganic lattice, making ZnO:PDINN-S ETL more suitable for the fabrication of flexible devices. Overall, doping ZnO with organic dye molecules offers an innovative strategy for developing multifunctional and efficient hybrid ETL of the non-fullerene OSCs with excellent efficiency and photo-stability.

High Conductivity, Semiconducting, and Metallic PEDOT:PSS Electrode for All-Plastic Solar Cells.

Plastic electrodes are desirable for the rapid development of flexible organic electronics. In this article, a plastic electrode has been prepared by employing traditional conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and plastic substrate polyethersulfone (PES). The completed electrode (Denote as HC-PEDOT:PSS) treated by 80% concentrated sulfuric acid (H2SO4) possesses a high electrical conductivity of over 2673 S/cm and a high transmittance of over 90% at 550 nm. The high conductivity is attributed to the regular arrangement of PEDOT molecules, which has been proved by the X-ray diffraction characterization. Temperature-dependent conductivity measurement reveals that the HC-PEDOT:PSS possesses both semiconducting and metallic properties. The binding force and effects between the PEDOT and PEI are investigated in detail. All plastic solar cells with a classical device structure of PES/HC-PEDOT:PSS/PEI/P3HT:ICBA/EG-PEDOT:PSS show a PCE of 4.05%. The ITO-free device with a structure of Glass/HC-PEDOT:PSS/Al4083/PM6:Y6/PDINO/Ag delivers an open-circuit voltage (VOC) of 0.81 V, short-circuit current (JSC ) of 23.5 mA/cm2, fill factor (FF) of 0.67 and a moderate power conversion efficiency (PCE) of 12.8%. The above results demonstrate the HC-PEDOT:PSS electrode is a promising candidate for all-plastic solar cells and ITO-free organic solar cells.

Dithieno[3,2-b:2',3'-d]pyrrole Cored p-Type Semiconductors Enabling 20 % Efficiency Dopant-Free Perovskite Solar Cells.

Organic p-type semiconductors with tunable structures offer great opportunities for hybrid perovskite solar cells (PVSCs). We report herein two dithieno[3,2-b:2',3'-d]pyrrole (DTP) cored molecular semiconductors prepared through π-conjugation extension and an N-alkylation strategy. The as-prepared conjugated molecules exhibit a highest occupied molecular orbital (HOMO) level of -4.82 eV and a hole mobility up to 2.16×10-4  cm2 V-1 s-1 . Together with excellent film-forming and over 99 % photoluminescence quenching efficiency on perovskite, the DTP based semiconductors work efficiently as hole-transporting materials (HTMs) for n-i-p structured PVSCs. Their dopant-free MA0.7 FA0.3 PbI2.85 Br0.15 devices exhibit a power conversion efficiency over 20 %, representing one of the highest values for un-doped molecular HTMs based PVSCs. This work demonstrates the great potential of using a DTP core in designing efficient semiconductors for dopant-free PVSCs.

Selenium-substituted polymers for improved photovoltaic performance.

Four isostructural donor-acceptor alternating polymers of benzodithiophene (BDT)/naphthodifuran (NDF) and benzoselenadiazole (BSe)/benzothiadiazole (BT) have been developed and evaluated for organic photovoltaics. The substitution of one-atom (Se for S) in the accepting units exerts remarkable impact on the optoelectronic properties of polymers. Extended absorption, narrowed bandgap and higher HOMO energy levels were observed for Se-containing polymers in comparison to their S-containing counterparts. Theoretical calculations confirmed the measurable effect on energy levels as found in experimental studies. Bulk-heterojuction solar cells based on the BDT-BSe copolymer and [6,6]-phenyl-C71-butyric acid methyl ester (1 : 2, w/w) blend films deliver the best PCE of 5.40%. BSe-based polymers showed enhanced photovoltaic performances than BT-based polymers. The device performance is found to be strongly dependent on the processing conditions and morphology of the active layers.

Hole Transport Layer-Free Low-Bandgap Perovskite Solar Cells for Efficient All-Perovskite Tandems.

Low-bandgap (LBG, Eg  ≈1.25 eV) tin-lead (Sn-Pb) perovskite solar cells (PSCs) play critical roles in constructing efficient all-perovskite tandem solar cells (TSCs) that can surpass the efficiency limit of single-junction solar cells. However, the traditional poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) hole transport layer (HTL) in LBG PSCs usually restricts device efficiency and stability. Here, a strategy of employing 2-aminoethanesulfonic acid (i.e., taurine) as the interface bridge to fabricate efficient HTL-free LBG PSCs with improved optoelectronic properties of the perovskite absorbers at the buried contacts is reported. Taurine-modified ITO substrate has lower optical losses, better energy level alignment, and higher charge transfer capability than PEDOT:PSS HTL, leading to significantly improved open-circuit voltage (VOC ) and short-circuit current density of corresponding devices. The best-performing LBG PSC with a power conversion efficiency (PCE) of 22.50% and an impressive VOC of 0.911 V is realized, enabling all-perovskite TSCs with an efficiency of 26.03%. The taurine-based HTL-free TSCs have highly increased stability, retaining more than 90% and 80% of their initial PCEs after constant operation under 1-sun illumination for 600 h and under 55 °C thermal stress for 950 h, respectively. This work provides a facile strategy for fabricating efficient and stable perovskite devices with a simplified HTL-free architecture.

Integrated transcriptomic and metabolomic analyses reveal key metabolic pathways in response to potassium deficiency in coconut (Cocos nucifera L.) seedlings.

Potassium ions (K+) are important for plant growth and crop yield. However, the effects of K+ deficiency on the biomass of coconut seedlings and the mechanism by which K+ deficiency regulates plant growth remain largely unknown. Therefore, in this study, we compared the physiological, transcriptome, and metabolite profiles of coconut seedling leaves under K+-deficient and K+-sufficient conditions using pot hydroponic experiments, RNA-sequencing, and metabolomics technologies. K+ deficiency stress significantly reduced the plant height, biomass, and soil and plant analyzer development value, as well as K content, soluble protein, crude fat, and soluble sugar contents of coconut seedlings. Under K+ deficiency, the leaf malondialdehyde content of coconut seedlings were significantly increased, whereas the proline (Pro) content was significantly reduced. Superoxide dismutase, peroxidase, and catalase activities were significantly reduced. The contents of endogenous hormones such as auxin, gibberellin, and zeatin were significantly decreased, whereas abscisic acid content was significantly increased. RNA-sequencing revealed that compared to the control, there were 1003 differentially expressed genes (DEGs) in the leaves of coconut seedlings under K+ deficiency. Gene Ontology analysis revealed that these DEGs were mainly related to "integral component of membrane," "plasma membrane," "nucleus", "transcription factor activity," "sequence-specific DNA binding," and "protein kinase activity." Kyoto Encyclopedia of Genes and Genomes pathway analysis indicated that the DEGs were mainly involved in "MAPK signaling pathway-plant," "plant hormone signal transduction," "starch and sucrose metabolism," "plant-pathogen interaction," "ABC transporters," and "glycerophospholipid metabolism." Metabolomic analysis showed that metabolites related to fatty acids, lipidol, amines, organic acids, amino acids, and flavonoids were generally down-regulated in coconut seedlings under K+ deficiency, whereas metabolites related to phenolic acids, nucleic acids, sugars, and alkaloids were mostly up-regulated. Therefore, coconut seedlings respond to K+ deficiency stress by regulating signal transduction pathways, primary and secondary metabolism, and plant-pathogen interaction. These results confirm the importance of K+ for coconut production, and provide a more in-depth understanding of the response of coconut seedlings to K+ deficiency and a basis for improving K+ utilization efficiency in coconut trees.

Cation and anion optimization of ammonium halide for interfacial passivation of inverted perovskite solar cells.

Perovskite solar cell (PSC) commercialization faces intrinsic stability and efficiency challenges. N1-phenylethane-1,2-diamine hydrohalides (PNEAX) based on a new design strategy featuring cation and anion optimization have been developed for efficient interfacial passivation. Among them, PNEACl-treated devices achieved a champion efficiency of 21.01% with good stability.

Defect passivation via a multifunctional organic additive toward efficient and stable inverted perovskite solar cells.

A multifunctional group molecule, namely MATC, was first introduced into a Cs/FA-based perovskite used as an additive. An impressive PCE of 21.51% was achieved for the inverted PSCs with reduced defect states and improved perovskite film quality. Moreover, MATC passivation considerably enhanced the stability of the PSC devices.

Surface termination passivation of imidazole-based diiodide enabling efficient inverted perovskite solar cells.

N-(3-aminopropyl)-imidazole diiodide (APDI) was introduced on the upper surface of the perovskite for the first time to modulate the terminal groups. The defect traps were suppressed by binding N cations from the APDI with Pb2+. Consequently, the optimum APDI-treated device achieved a PCE of 21.41% and exhibited excellent stability.

Highly Stable Supercapacitors Enabled by a New Conducting Polymer Complex PEDOT:CF3 SO2(x) PSS(1-x).

Herein, a novel conducting polymer complex PEDOT:CF3 SO2(x) PSS(1-x) [denoted as S-PEDOT:CF3 SO2(x) PSS(1-x) , where PEDOT is poly(3,4-ethylenedioxythiophene) and PSS is poly(styrene sulfonate)], is fabricated with the assistance of zinc di[bis(trifluoromenthylsulfonyl) imide][Zn(TFSI)2 ] (CFE). The introduction of CF3 SO2 - group is expected to bring better stability of PEDOT:CF3 SO2 than PEDOT:PSS due to its strong Coulomb force. Electrochemical measurement shows that a high specific capacitance of 194 F cm-3 was achieved from the novel complex S-PEDOT:CF3 SO2(x) PSS(1-x) , the highest value reported so far. An all-solid-state supercapacitor assembly with a structure of S-PEDOT:CF3 SO2(x) PSS(1-x) /H2 SO4 :polyvinyl alcohol (PVA)/S-PEDOT:CF3 SO2(x) PSS(1-x) shows a record specific capacitance of 70.9 F cm-3 and a maximum energy density of 6.02 mWh cm-3 at a power density of 397 mW cm-3 . This supercapacitor device demonstrates excellent electrochemical stability with a capacitance retention rate of 98 % after 10 000 cycles and extreme air stability of 96 % capacitance retention rate after 10 000 cycles, even if the device is exposed to air over 2880 h, much better than that of PEDOT:PSS based supercapacitors. Excellent capacitance can be achieved from PEDOT:CF3 SO2(x) PSS(1-x) electrode under electrolyte-free conditions. This work provides a novel method for high performance stable supercapacitors and may pave the way for the commercialization of PEDOT based supercapacitors.

Effects of Concurrent Strength and HIIT-Based Endurance Training on Physical Fitness in Trained Team Sports Players: A Systematic Review and Meta-Analysis.

BACKGROUND: Concurrent strength and HIIT-based endurance training (CT) has merit in time-saving in team sports. However, the effect of CT on physical fitness remained equivocal. This meta-analysis aimed to determine whether CT would produce an interference effect on the development of physical fitness when compared to strength training (ST) or HIIT-based endurance training (HET) alone in trained team sports players. METHODS: A total of 2478 studies from three databases were screened. 52 full texts were reviewed. Seven studies were finally included and then subgroups were used for quantitative analysis. RESULTS: Compared to ST alone, CT had a significant effect on the development of maximal lower-body strength in trained team sports players (MD 4.20 kg, 95% CI 0.71-7.68, p = 0.02, I2 = 20%), but there was no significant difference between the groups on training adaptation in lower-body power (SMD 0.08, 95% CI -0.23-0.39, p = 0.62, I2 = 26%). Furthermore, a sub-group analysis based on the internal organization order of CT revealed that there was no statistically significant subgroup effect between CT and ST alone in all parameters. CONCLUSIONS: Well-designed CT regimens did not interfere with the development of physical fitness of trained team sports players.

Novel dopant-free hole transport materials enabling 20.9% efficiency in perovskite solar cells.

Two novel donor-acceptor-donor (D-A-D) type dopant-free hole transport materials (HTMs), named BDD-T and BTT-T, were developed and applied in perovskite solar cells. An impressive power conversion efficiency (PCE) of 20.9% was acquired, which is one of the highest PCEs for D-A-D type dopant-free HTMs.

Plasmon-coupled Au-nanochain functionalized PEDOT:PSS for efficient mixed tin-lead iodide perovskite solar cells.

Au nanochains with a coupled plasmonic nanostructure were first introduced into PEDOT:PSS used as a hole transport layer to fabricate mixed tin-lead PSCs. The improved electrical properties and the promotion of optical absorption contributed to a high PCE of 19.2%. Moreover, the PSCs show substantial enhancement in stability.

Highly efficient and stable ZnO-based perovskite solar cells enabled by a self-assembled monolayer as the interface linker.

2-TA and 3-TA were introduced for the first time on the surface of ZnO, and used as SAMs for interfacial modification. A highest PCE of 20.6% was achieved for 2-TA PSCs with improved energy alignment and perovskite film quality, and reduced defect density. The modified ZnO exhibited better thermostability of the perovskite and resultant device stability.

Identification and function prediction of iron-deficiency-responsive microRNAs in citrus leaves.

Iron is a critical micronutrient for growth and development of plants and its deficiency limiting the crop productivity. MicroRNAs (miRNAs) play vital roles in adaptation of plants to various nutrient deficiencies. However, the role of miRNAs and their target genes related to Fe-deficiency is limited. In this study, we identified Fe-deficiency-responsive miRNAs from citrus. In Fe-deficiency conditions, about 50 and 31 miRNAs were up-regulated and down-regulated, respectively. The differently expressed miRNAs might play critical roles in contributing the Fe-deficiency tolerance in citrus plants. The miRNAs-mediated Fe-deficiency tolerance in citrus plants might related to the enhanced stress tolerance by decreased expression of miR172; regulation of S homeostasis by decreased expression of miR395; inhibition of plant growth by increased expression of miR319 and miR477; regulation of Cu homeostasis as well as activation of Cu/Zn superoxide dismutase activity due to decreased expression of miR398 and miR408 and regulation of lignin accumulation by decreased expression of miR397 and miR408. The identified miRNAs in present study laid a foundation to understand the Fe-deficiency adaptive mechanisms in citrus plants. SUPPLEMENTARY INFORMATION: The online version contains supplementary material available at 10.1007/s13205-021-02669-z.

Research Progress on Polymer Solar Cells Based on PEDOT:PSS Electrodes.

Solution-processed polymer solar cells (PSCs) have attracted dramatically increasing attention over the past few decades owing to their advantages of low cost, solution processability, light weight, and excellent flexibility. Recent progress in materials synthesis and devices engineering has boosted the power conversion efficiency (PCE) of single-junction PSCs over 17%. As an emerging technology, it is still a challenge to prepare solution-processed flexible electrodes for attractive flexible PSCs. Poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) is one of the most promising candidates for electrodes due to its high conductivity (>4000 S/cm), excellent transmittance (>90%), intrinsically high work function (WF > 5.0 eV), and aqueous solution processability. To date, a great number of single-junction PSCs based on PEDOT:PSS electrodes have realized a PCE over 12%. In this review, we introduce the current research on the conductive complex PEDOT:PSS as well as trace the development of PEDOT:PSS used in electrodes for high performance PSCs and perovskite solar cells. We also discuss and comment on the aspects of conductivity, transmittance, work-function adjustment, film preparing methods, and device fabrications. A perspective on the challenges and future directions in this field is be offered finally.

High-Conductivity, Flexible and Transparent PEDOT:PSS Electrodes for High Performance Semi-Transparent Supercapacitors.

Herein, we report a flexible high-conductivity transparent electrode (denoted as S-PH1000), based on conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS), and itsapplication to flexible semi-transparentsupercapacitors. A high conductivity of 2673 S/cm was achieved for the S-PH1000 electrode on flexible plastic substrates via a H2SO4 treatment with an optimized concentration of 80 wt.%. This is among the top electrical conductivities of PEDOT:PSS films processed on flexible substrates. As for the electrochemical properties,a high specific capacitance of 161F/g was obtained from the S-PH1000 electrode at a current density of 1 A/g. Excitingly, a specific capacitance of 121 F/g was retained even when the current density increased to 100 A/g, which demonstrates the high-rate property of this electrode. Flexible semi-transparent supercapacitors based on these electrodes demonstrate high transparency, over 60%, at 550 nm. A high power density value, over 19,200 W/kg,and energy density, over 3.40 Wh/kg, was achieved. The semi-transparent flexible supercapacitor was successfully applied topower a light-emitting diode.

Dithieno[3,2-b:2',3'-d]pyrrol Fused Nonfullerene Acceptors Enabling Over 13% Efficiency for Organic Solar Cells.

A new electron-rich central building block, 5,5,12,12-tetrakis(4-hexylphenyl)-indacenobis-(dithieno[3,2-b:2',3'-d]pyrrol) (INP), and two derivative nonfullerene acceptors (INPIC and INPIC-4F) are designed and synthesized. The two molecules reveal broad (600-900 nm) and strong absorption due to the satisfactory electron-donating ability of INP. Compared with its counterpart INPIC, fluorinated nonfullerene acceptor INPIC-4F exhibits a stronger near-infrared absorption with a narrower optical bandgap of 1.39 eV, an improved crystallinity with higher electron mobility, and down-shifted highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels. Organic solar cells (OSCs) based on INPIC-4F exhibit a high power conversion efficiency (PCE) of 13.13% and a relatively low energy loss of 0.54 eV, which is among the highest efficiencies reported for binary OSCs in the literature. The results demonstrate the great potential of the new INP as an electron-donating building block for constructing high-performance nonfullerene acceptors for OSCs.

Side-chain Engineering of Benzo[1,2-b:4,5-b']dithiophene Core-structured Small Molecules for High-Performance Organic Solar Cells.

Three novel small molecules have been developed by side-chain engineering on benzo[1,2-b:4,5-b']dithiophene (BDT) core. The typical acceptor-donor-acceptor (A-D-A) structure is adopted with 4,8-functionalized BDT moieties as core, dioctylterthiophene as π bridge and 3-ethylrhodanine as electron-withdrawing end group. Side-chain engineering on BDT core exhibits small but measurable effect on the optoelectronic properties of small molecules. Theoretical simulation and X-ray diffraction study reveal the subtle tuning of interchain distance between conjugated backbones has large effect on the charge transport and thus the photovoltaic performance of these molecules. Bulk-heterojunction solar cells fabricated with a configuration of ITO/PEDOT:PSS/SM:PC71BM/PFN/Al exhibit a highest power conversion efficiency (PCE) of 6.99% after solvent vapor annealing.