Measurement method of hot forging dimension based on green laser depth information.

The application field of large forgings is extensive. Accurate dimensional measurement is an important factor to ensure the quality of the finished forging product when it is forged at high temperature. Therefore, this paper proposes a green laser scanning measurement method based on depth information. First, a geometric measurement model based on depth information is established by studying the relationship between green laser depth information and forging dimension. Then, based on the heat transfer theory, distribution of the temperature field around hot forgings is studied, and an error function caused by light refraction is established using a ray tracing algorithm. After that, the error function is used to modify the measurement model to obtain the accurate distance between the forging and background plane and then obtain the dimensional information of the forging. Finally, this measurement method was experimentally verified in the laboratory, and the experimental results show that the measurement error of this method meets the dimensional measurement requirements of large hot forgings.

First Report of Root Rot of Cathaya argyrophylla caused by Fusarium oxysporum in China.

Cathaya argyrophylla [Chun & Kuang.] is an ancient relict plant and its embryonic development is similar to that of Pinus species. This has important scientific value for studying the phylogeny of Pinaceae (Wu et al. 2023). In July 2022, root rot was detected in the seedling cultivation base of C. argyrophylla in Daozhen County, Guizhou Province, China (28.89 °N, 107.6 °E). The incidence of the disease was 30% (n = 100); the susceptible plants wilted, leaves withered, and roots showed brown-to-black lesions and rot. Ten root tissues were randomly collected from the edges of the lesions of six symptomatic susceptible plants. The tissues were sterilized with 75% alcohol for 30 seconds, followed by 2-minute immersion in 3% sodium hypochlorite. After washing with sterile water, the tissues were incubated on potato dextrose agar (PDA; BoWei, Shanghai) at 28 ℃ for five days. Four single-spore cultures were obtained using a single-spore isolation method (Gong et al., 2010). Single-spore cultures grew rapidly on PDA. After five days of incubation, the colonies were white and pink, indicating a large amount of aerial mycelia. Microconidia were ovate or ellipsoid, measuring 5.0-10.0 × 1.5-3.0 µm (n = 50); Macroconidia were falcate, slightly curved or straight, measuring 19.5-28.5 × 2.0-6.0 µm (n = 50). Based on morphological features, the pathogen was considered to be Fusarium spp. (Leslie and Summerell 2006). Three representative strains, GF5, GF6, and GF7, were selected for molecular identification, and genomic DNA was extracted to confirm morphological diagnosis. The internal transcribed spacer (ITS) (White et al. 1990) was amplified using primers ITS1/ITS4, and the ß-tubulin gene (Varga et al. 2011) was amplified using primers Bt2a/Bt2b. The ITS and ß-tubulin sequences were aligned with GenBank, and amplification of the genes from the three isolates was consistent. The ITS (OP482273) and ß-tubulin (OR825353) sequences of GF5 were stored in GenBank, and their homology with Fusarium oxysporum HC131(accession numbers MW600442 and MW670451) was 99 to 100%. Maximum likelihood analysis using MEGA 11.0 showed that isolate GF5 belongs to F. oxysporum. The reconstructed phylogenetic tree confirmed the phylogenetic position of the isolate GF5. The pathogenicity test was carried out using GF5 and GF6 isolates. The taproots of ten 3-year-old C. argyrophylla plants were washed, and then the roots were immersed in a 2 × 106/mL conidial suspension for one hour. Ten plants with sterile water were used as controls. After planting in pots (30 × 25 cm) with sterilized forest soil, the plants were cultured in a greenhouse (25 ℃ and 12-hour photoperiod). Thirty days after inoculation, all plants inoculated with the isolated pathogen showed wilting symptoms, and the roots showed typical root rot symptoms, whereas the control group showed no symptoms. The pathogens re-isolated from all inoculated plants were morphologically identical and had ITS sequences identical to F. oxysporum, validating Koch's hypothesis. The pathogenicity test was repeated twice and similar results were obtained. Although this fungus has been previously reported to cause root diseases in hosts, such as Musa nana Lour. and Pinus massoniana Lamb. (He et al. 2010; Luo et al. 2020), to our knowledge, this is the first report of F. oxysporum causing root rot in C. argyrophylla. These findings provide a basis for the development of management strategies for C. argyrophylla infection.

First Report of Leaf Spot Blight of Camellia oleifera Caused by Diaporthe mahothocarpus in China.

Camellia oleifera Abel. is one of the native and important natural edible oil species in China. The cultivation of C. oleifera has vigorously increased in Guizhou Province in recent years. From June to August 2022, a severe leaf spot blight was observed on C. oleifera in Longli Plantation, with an incidence of 53.5% (n=200), which caused severe defoliation, negatively affected plant growth, and led to significant economic losses. Pale yellow and sub-circular leaf spots of 2-5 mm in diameter first appeared in the margin. The center of the spots then turned grey, and the edges turned brown. The symptomatic leaves gradually developed symptoms of blight with some brown acervular conidiomata, died, and fell off, with many deep black spots on the leaves (Fig. 1A-B). The fungal isolates GZU-Y2 and GZU-Y3 were obtained from the infected leaves of five-year-old symptomatic C. oleifera trees using the tissue isolation method, and a voucher specimen was deposited in the Forest Protection Laboratory, Guizhou University. Cultures grown on potato dextrose agar medium (PDA) were incubated at 28℃, 16L/8D. A round cream-like colony was formed on PDA, with a white surface, while the back gradually turned brown (Fig. 1C-E). The aerial hypha grew vigorously with an initial milky white color before turning grayish white. At 10 days after incubation, the pycnidia were dark brown to black and spherical, with a diameter of 563.3 µm (500 to 700) (n=20). The alpha conidia were unicellular, hyaline, aseptate, oval or fusiform and measured 6.1 µm (4.1 to 8.0) × 2.6 µm (1.9 to 3.6) (n=50). However, no beta conidia were observed (Fig. 1I). For further identification, total DNA from the pure culture was extracted using a DNA extraction kit (Sangon, Shanghai, China), and the internal transcribed spacer (ITS), translation elongation factor 1-α (TEF-1α), and beta-tubulin (TUB2) were amplified by PCR using the primers ITS1/ITS4 (White et al., 1990), EF1-728F/EF1-986R (Carbone and Kohn, 1999) and Bt2a/Bt2b (Glass and Donaldson, 1995), respectively, and sequenced for a BLASTn analysis and phylogenetic tree construction. The sequences of ITS, TEF-1α and TUB2 were deposited in GenBank as accession numbers OQ168242 (99.25%), OQ689451 (99.71%) and OQ689453 (100.00%) for GZU-Y2 and OQ674554 (99.25%), OQ689452 (99.71%) and OQ689454 (100.00%) for GZU-Y3, respectively. A phylogenetic tree (Fig. 2) was constructed with the software MEGA X using the Neighbor-Joining algorithm (Felsenstein, 1985). Based on its morphological and molecular characteristics, the pathogen was identified as Diaporthe mahothocarpus, one of the synonyms of D. eres and the teleomorph of Phomopsis mahothocarpi (Gao et al., 2014 and 2015; Chaisiri et al., 2021). A pathogenicity test was conducted by spraying spore suspensions (2 × 107 spores/mL) of isolate GZU-Y2 on the leaves of 20 pots of annual C. oleifera seedlings in vivo. The same number of control seedings were sprayed with sterile water. The seedlings were placed at a constant room temperature of 28°C, with the inoculation points wrapped in Parafilm for 5 d to retain moisture. After 10 d, typical symptoms appeared on the inoculated leaves (Fig. 1F-H), and the re-isolated fungal culture was identical in morphology and ITS sequence to that originally obtained, fulfilling Koch's postulates. To our knowledge, this is the first report of D. mahothocarpus causing leaf spot blight of C. oleifera in China. In our future work, we tend to study the green prevention and control of this disease.

First report of Root rot in Cerasus subhirtella Caused by Fusarium solani and Fusarium oxysporum in China.

Cerasus subhirtella (Miq.) Sok. is a widely used ornamental tree in urban areas around China and has a high ornamental value. From 2018 to 2020, a root rot disease was observed in C. subhirtella in Meitan County, Weng'an County, and Guiyang city of Guizhou, China (106.71 E, 26.57 N). Diseased C. subhirtella trees exhibited wilting with leaf chlorosis accompanied by brown to black root discoloration. In an area of 100 ha in total, with disease incidence ranging from 60 to 80%. Six symptomatic plants with root rot were randomly collected from three locations where disease symptoms were observed for pathogen isolation. Fifty fragments of diseased roots (5×5mm) were disinfected in 3% sodium hypochlorite for 30 s and 75% alcohol for 60 s, rinsed three times in sterile distilled water, plated on potato dextrose agar (PDA; BoWei, Shanghai), and incubated at 28 °C in the dark for 7 days. Eighteen isolates were purified by single spore culturing. Typical Fusarium spp. colonies were obtained from all root samples. On PDA, the colonies showed white and the hyphae were dense, while the colony of isolate YH15 showed pale yellow on the back, radial growth and produced chlamydospores. The macrospores (YH15) were straight to subarcuate, measured 15.3 to 25.1 × 2.5 to 6.2 µm (n=50). The microconidia (YH26) were ellipsoid to ovoid, measured 8.6 to 12.7 × 1.6 to 5.1 µm (n=50). These morphological characteristics were consistent with Fusarium spp., as described recently in Vitullo et al. (2014). To confirm the morphological diagnosis, genomic DNA from the isolates was extracted. The internal transcribed spacer (ITS) (White et al, 1990) region of rDNA and a ß-tubulin (Varga et al, 2011) gene fragment were amplified with the primers ITS1/ITS4 and Bt2a/Bt2b, respectively, and were subsequently sequenced. Maximum likelihood analysis was carried out using MEGA 11.0. BLAST analysis revealed that the ITS and ß-tubulin sequences of isolate YH15 were 100% homologous with F. oxysporum, and the isolate YH26 had a 99.69~100% homology with F. solani. Sequences of isolate YH15 and YH26 were deposited in GenBank (ITS: OQ363005 and OQ363049; ß-tubulin: OQ398187 and OQ398180). The isolate YH15 was thus identified as F. oxysporum by the morphological characteristics and sequences analysis, and the isolate YH26 was identified as F. solani. A reconstructed phylogenetic tree also confirmed their phylogenetic position. The healthy 2-year-old C. subhirtella plants grown in autoclaved acid yellow soil were used for the pathogenicity tests. Then, 50 mL of conidial suspension (2.0×105 conidia/mL, in medium) of 7-day-old isolates YH15 and YH26 were gently applied to the soil in each of the 10 pots as the treatment. A sterilized fungal culture matrix (PDB; BoWei, Shanghai) was applied to each of 10 pots as a control. All pots (30 cm high, 25 cm upper diameter, 15 cm base diameter) were placed in a greenhouse (25 °C, 12 h photoperiod). After 30 days of inoculation, all plants inoculated with the isolates showed wilting symptoms, and the roots showed light-brown to dark-brown lesions. No symptoms were observed in the controls. The pathogen was reisolated from all symptomatic roots and identified as F. oxysporum and F. solani as described above. The pathogenicity test was repeated twice with similar results. Although this fungus was previously reported to cause root disease in many hosts (Li et al., 2020; Gibert et al., 2022), this is the first report of F. oxysporum and F. solani causing root rot in C. subhirtella in China.

The Etiological Heterogeneity of Bicuspid Aortopathy between Ascending and Root Morphotype.

BACKGROUND: Valve-related hemodynamics and intrinsically regulated matrix proteases are 2 determined pathogenetic factors associated with medial elastin degeneration in bicuspid aortopathy. This study analyzed the association between elastic fiber deterioration and the 2 pathogenetic factors in ascending and root morphotypes, aiming to elucidate the etiological heterogeneity between the 2 morphotypes. METHODS: Four-dimensional flow cardiac magnetic resonance was used to measure the regional wall shear stress (WSS) on the ascending aorta, and matrix metalloproteinase (MMP) expression was assessed by immunoblotting. After histopathology analysis of aortic tissue, we assessed whether elevated regional WSS and increased MMP expression corresponded with medial elastin thinning. RESULTS: Increased regional WSS corresponded with medial elastin thinning in both morphotypes. Increased expression of different MMP isoforms corresponded with medial elastin degeneration in bicuspid aortopathy. The significantly increased expression of MMP-2 corresponded with a decrease of elastic fiber thickness in the ascending morphotype (P = .046), whereas elastic fiber thinning was associated with high levels of MMP-3 expression (P = .012) in the root morphotype. No association was observed between regional WSS and MMP expression. CONCLUSION: There is no difference in the effect of valve-related hemodynamics between ascending and root morphotype, and MMPs are not involved in the process of elastic fiber degeneration induced by increased WSS. The increased expression of different MMP isoforms was observed in the context of elastic fiber degeneration between the 2 morphotypes, implying that heterogeneity between them is revealed in the different intrinsic pathway of medial elastin degradation.

[Risk Factors for Acute Renal Failure after Thoracoabdominal Aortic Aneurysm Surgery].

Objective To investigate the risk factors associated with acute renal failure (ARF) after thoracoabdominal aortic aneurysm (TAAA) surgery. Methods A total of 156 patients underwent TAAA repair between January 2009 and December 2017. Renal failure was defined based on the Kidney Disease Improving Global Outcomes criteria. The patients were divided into ARF group and non-ARF group based on the presence/absence of postoperative ARF. The risk factors of ARF were analyzed by univariate analysis and multivariate logistic analysis. Results The subjects included 111 males and 45 females aged (40.4±10.9) years (range:19-65 years). The surgical reasons included aortic dissection (n=130,83.3%),aneurysm (n=22,14.1%),and pseudoaneurysm (n=4,2.6%). The degrees of repair included Crawford extent I in 6 patients (3.8%),extent Ⅱ in 128 patients (82.1%),extent Ⅲ in 20 patients (12.8%),and extent Ⅳ in 2 patients(1.3%). There were 3 patients presented with aortic rupture and 6 patients received emergent operations. Nine patients (5.8%) died within 30 days after surgery,and 8 patients (5.1%) suffered from permanent paraplegia. Thirty-six patients (23.1%) had ARF after surgery,and 18 of them needed dialysis. Multivariate logistic analysis showed that smoking (OR =2.637,95%CI=1.113-6.250,P=0.028),packed red blood cell usage in operation (≥6 U) (OR =5.508,95%CI=2.144-11.930,P=0.000),reoperation for bleeding (OR=3.529,95%CI=1.298-9.590,P=0.013) were independent risk factors for ARF after TAAA repair. Conclusion Smoking,packed red blood cell usage in operation (≥6 U),reoperation for bleeding are the independent risk factors of ARF after TAAA surgery.

Surgical treatment for Kommerell's diverticulum associated with aortic dissection involving aortic arch.

OBJECTIVE: Kommerell diverticulum with aortic dissection involving aortic arch is a rare but troublesome condition. The purpose of this study is to summarize the experience and strategy of surgical treatment. METHOD: From November 2015 to January 2018, seven consecutive patients underwent surgical treatment in our institution. Three patients with acute type A aortic dissection and one patient with acute type B aortic dissection received total arch replacement and frozen elephant trunk (FET) implantation through median sternotomy. Three patients with chronic type B aortic dissection underwent total aortic arch and descending aorta replacement through median sternotomy and lateral thoracotomy. RESULT: There were seven male patients whose median age was 42.3 ± 11.7 (from 14 to 54) years old. There was no perioperative death in this study. One patient had postoperative critical illness polyneuropathy and required prolonged mechanical ventilation (485 hours) and recovered finally. Follow up was completed for all seven patients with a median follow-up time of 7 (3-46) months. One patient with type A dissection developed aneurysm of the descending aorta distal to the FET and received reintervention. No clinical events and abnormal computed tomography manifestations were found in the other seven patients. CONCLUSION: Total arch replacement and FET through single median incision is a reliable method for Kommerell diverticulum associated with acute dissection involving arch. For Kommerell diverticulum associated with chronic type A or B aortic dissection involving aortic arch, graft replacement by double or single incision is safe and appropriate.

[Early and Midterm Results of Thoracoabdominal Aortic Aneurysm Repair in Patients with Marfan Syndrome].

Objective To evaluate the early and midterm results of surgical repair of thoracoabdominal aortic aneurysm(TAAA)in patients with Marfan syndrome(MFS). Methods The clinical data of patients with MFS undergoing TAAA repair in Fuwai Hospital between January 2009 and December 2017 were retrospectively analyzed.These patients were divided into two groups:MFS group(n=58)and non-MFS group(n=98).The baseline data,early postoperative results,and midterm follow-up outcomes were compared between these two groups. Results MFS patients were significantly younger(32 years old vs. 45 years old,t=9.603,P=0.000)and more frequently had a history of aortic aneurysm or dissection(19% vs. 0,χ 2=19.996,P=0.000)than non-MFS patients.However,the proportions of males and smokers were significantly lower when compared with non-MFS patients(55.2% vs. 80.6%,χ 2=11.489,P=0.001;13.8% vs. 46.9%,χ 2=17.686,P=0.001).There was no significant difference in proportion of emergency operation,prophylactic cerebrospinal fluid drainage,operation time,intra-operative circulation management,and intra-operative blood transfusion(all P>0.05).The 30-day mortality rate was significantly lower in MFS group than in non-MFS group(0 vs. 9.2%, [Formula: see text]=5.034,P=0.025). Conclusions For patients with MFS,TAAA repair provides lower 30-day mortality and comparative middle-term survival.However,the re-intervention rate is higher among MFS patients,highlighting the importance of close follow-up.

Synthesis and Electrochemical Properties of Yb3+-Doped Li1.20Mn0.54Ni0.13Co0.13O2 Cathode Materials Obtained by Sol-Gel Method.

The Li1.20[Mn0.54Ni0.13Co0.13]0.80-xYbxO2 (x = 0, 0.01, 0.02, 0.03) cathode materials have been synthesized by using sol-gel method and characterized by means of XRD, SEM, ICP-OES analysis. The galvanostatic charge-discharge tests results showed the improved electrochemical properties were obtained through the Yb3+ doping modification. With the increase of Yb3+ doping content, the capacity retentions enhanced from 85.6% to 88.9% and then decrease to 86.5% after 100 cycles with x = 0.01, 0.02 and 0.03, respectively, while the un-doped sample delivered the capacity retention of 83.0%. Besides, the discharge capacity of Li1.20 [Mn0.54Ni0.13Co0.13]0.78Yb0.02O2 was about 23.1 mAh g-1 larger than that of un-doped sample at 5C high rate. The electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicated that the Yb3+ doping modification could suppress the layered-spinel phase transformation during cycling and maintain a lower value of charge transfer impedance.

Dicer1/miR-29/HMGCR axis contributes to hepatic free cholesterol accumulation in mouse non-alcoholic steatohepatitis.

Dicer1 is an enzyme essential for microRNA (miRNA) maturation. The loss of miRNAs resulted from Dicer1 deficiency greatly contributes to the progression of many diseases, including lipid dysregulation, but its role in hepatic accumulation of free cholesterol (FC) that is critical in the development of non-alcoholic steatohepatitis (NASH) remains elusive. In this study, we used the liver-specific Dicer1-knockout mice to identify the miRNAs involved in hepatic FC accumulation. In a widely used dietary NASH model, mice were fed a methionine-choline-deficient (MCD) diet for 3 weeks, which resulted in significant increase in hepatic FC levels as well as decrease of Dicer1 mRNA levels in livers. The liver-specific Dicer1-knockout induced hepatic FC accumulation at 5-6 weeks, accompanied by increased mRNA and protein levels of 3-hydroxy-3-methylglutaryl coenzyme A reductase (HMGCR), a rate-limiting enzyme of cholesterol synthesis in livers. Eleven predicted miRNAs were screened, revealing that miR-29a/b/c significantly suppressed HMGCR expression by targeting the HMGCR mRNA 3'-UTR. Overexpression of miR-29a in SMMC-7721 cells, a steatosis hepatic cell model, significantly decreased HMGCR expression and the FC level. Furthermore, the expression levels of miR-29a were inversely correlated with HMGCR expression levels in the MCD diet mouse model in vivo and in 2 steatosis hepatic cell models (SMMC-7721 and HL-7702 cells) in vitro. Our results show that Dicer1/miR-29/HMGCR axis contributes to hepatic free cholesterol accumulation in mouse NASH, and miR-29 may serve as an important regulator of hepatic cholesterol homeostasis. Thus, miR-29a could be utilized as a potential therapeutic target for the treatment of non-alcoholic fatty liver disease as well as for other liver diseases associated with FC accumulation.

MicroRNA-1304 suppresses human non-small cell lung cancer cell growth in vitro by targeting heme oxygenase-1.

Previous studies have shown that microRNA-1304 (miR-1304) is dysregulated in certain types of cancers, including non-small cell lung cancer (NSCLC), and might be involved in tumor survival and/or growth. In this study we investigated the direct target of miR-1304 and its function in NSCLC in vitro. Human lung adenocarcinoma cell lines (A549 and NCI-H1975) were studied. The cell proliferation and survival were investigated via cell counting, MTT and colony-formation assays. Cell apoptosis and cell cycle were examined using annexin V-PE/7-AAD and PI staining assays, respectively. The dual-luciferase reporter assay was used to verify post-transcriptional regulation of heme oxygenase-1 (HO-1) by miR-1304. CRISPR/Cas9 was used to deplete endogenous miR-1304. Overexpression of MiR-1304 significantly decreased the number and viability of NSCLC cells and colony formation, and induced cell apoptosis and G0/G1 phase cell cycle arrest. HO-1 was demonstrated to be a direct target of miR-1304 in NSCLC cells. Restoration of HO-1 expression by hemin (20 µmol/L) abolished the inhibition of miR-1304 on cell growth and rescued miR-1304-induced apoptosis in A549 cells. Suppression of endogenous miR-1304 with anti-1304 significantly increased HO-1 expression and promoted cell growth and survival in A549 cells. In 17 human NSCLC tissue samples, miR-1304 expression was significantly decreased, while HO-1 expression was significantly increased as compared to normal lung tissues. MicroRNA-1304 is a tumor suppressor and HO-1 is its direct target in NSCLC. The results suggest the potential for miR-1304 as a therapeutic target for NSCLC.

Intercostal Artery Reconstruction: The Simple and Effective Technique on Spinal Cord Protection during Thoracoabdominal Aortic Replacement.

BACKGROUND: To retrospectively analyze the role of intercostal artery reconstruction in the spinal cord protection for patients undergoing extensive thoracoabdominal aortic aneurysm repair. METHODS: From August 2007 to 2014, thoracoabdominal aortas (Crawford II) of 81 consecutive patients with mean age 39.4 ± 10.32 years were repaired. Seventy-three of these patients (90.12%) were diagnosed with aortic dissection in our group, 25 (30.86%) with Stanford type A dissection and 48 (59.26%) with Stanford B aortic dissection. All 25 patients with type A dissection have previously undergone surgical procedures which include Bentall's procedures in 11 cases, ascending aortic replacement in 6 cases, and total aortic arch replacement in 8 cases. All procedures were performed under profound hypothermia with interval cardiac arrest after making a thoracoabdominal incision. Extracorporeal circulation was instituted with 2 arterial cannulae and a single venous cannula in the right atrium. T6-T12 intercostal arteries and L1 and L2 lumbar arteries were formed to a neo-intercostal artery in place and were connected to an 8 mm branch for maintaining spinal cord blood perfusion. Visceral arteries were joined into a patch and anastomosed to the end of the main graft. The left renal artery was anastomosed to an 8 mm branch or joined to the patch. The other 10 mm branches were anastomosed to iliac arteries. RESULTS: With 100% follow-up, early mortality was 7.4%. Six deaths were recorded; 1 patient died of cerebral hemorrhage, 3 of renal failure, 1 of heart failure because of myocardial infarction, and the last one died from the rupture of celiac artery dissection. The rate of postoperative spinal cord deficits was 3.7%, 2 patients with paraplegia and 1 patient with paraparesis. None had bladder or rectum dysfunction. Neo-intercostal arteries were clogged in 12 patients within follow-up period and formed pseudoaneurysm in 2 patients with Marfan syndrome. The mean survival time in this group was 54.22 ± 3.03 months (95% confidence interval 44.37-59.90 months) with survival rate of 92.37% after 1 year, 89.02% after 2 years, and 85.54% after 5 years. All patients were free from spinal cord deficits. CONCLUSIONS: Intercostal artery reconstruction is an effective technique for spinal cord protection in patients with the thoracoabdominal aortic repair. It can achieve favorable results and avoid spinal cord deficits with long-term follow-up.

Protective effect of hydrogen sulfide on TNF-α and IFN-γ-induced injury of intestinal epithelial barrier function in Caco-2 monolayers.

BACKGROUND AND AIM: Studies have verified the protective effect of Hydrogen Sulfide (H2S) on gastric ulcer and ulcerative colitis, but the mechanisms are not fully illustrated. In this study, the possible protective effect of H2S on TNF-α/IFN-γ induced barrier dysfunction was investigated in Caco-2 cell monolayers. METHOD: The barrier function of Caco-2 monolayers was evaluated by measuring trans-epithelial electrical resistance (TEER) and FITC-Dextran 4 kDa (FD-4) trans-membrane flux. ZO-1 and Occludin were chosen as markers of the localization of tight junction (TJ) proteins for immunofluorescence. The expression of MLCK and phosphorylation level of myosin light chain (MLC) were measured by immunoblotting. The activation of NF-kB p65 was analyzed by EMSA and immunofluorescence. RESULTS: NaHS at 500 uM significantly attenuated TNF-α/IFN-γ-indueced Caco-2 monolayer barrier injury. The increased expression of MLCK and increased phosphorylation level of MLC induced by TNF-α/IFN-γ was also inhibited significantly by NaHS. Additionally, NaHS inhibited TNF-α/IFN-γ induced activation and nuclear translocation of NF-kB p65. CONCLUSION: The present study reveals the protective effect of H2S on TNF-α and IFN-γ-induced injury of intestinal epithelial barrier function in Caco-2 monolayers and suggests that the suppression of MLCK-P-MLC signaling mediated by NF-kB P65 might be one of the mechanisms underlying the protective effect of H2S.

[Research on the inner wall condition monitoring method of ring forgings based on infrared spectra].

In order to grasp the inner wall condition of ring forgings, an inner wall condition monitoring method based on infrared spectra for ring forgings is proposed in the present paper. Firstly, using infrared spectroscopy the forgings temperature measurement system was built based on the three-level FP-cavity LCTF. The two single radiation spectra from the forgings' surface were got using the three-level FP-cavity LCTF. And the temperature measuring of the surface forgings was achieved according to the infrared double-color temperature measuring principle. The measuring accuracy can be greatly improved by this temperature measurement method. Secondly, on the basis of the Laplace heat conduction differential equation the inner wall condition monitoring model was established by the method of separating variables. The inner wall condition monitoring of ring forgings was realized via combining the temperature data and the forgings own parameter information. Finally, this method is feasible according to the simulation experiment. The inner wall condition monitoring method can provide the theoretical basis for the normal operating of the ring forgings.

[Monitoring of Curing Temperature of Pouring Explosive Based on Fiber Bragg Grating].

For the first time, we real time measured released reaction heat between the binder and the curing agent in the curing process of cast explosive using fiber Bragg grating. In order to obtain the temperature in the process of pouring explosive casting real time and accurately, we designed the temperature monitoring system based on fiber Bragg grating. Given the risk of explosive component, long curing time and the requirements of constant temperature, a suitable measurement method for direct real-time monitoring has not been found. In recent years, due to its superior characteristics, fiber Bragg grating is widely used in the field of communication and sensing. We will make the collected reflection wavelength to convert real-time temperature displaying, utilizing linear relationship between fiber Bragg grating and temperature. Through WDM technology, seven grating points are written in two optical fibers to measure at the same time, and distribution trend of explosives internal temperature can be displayed in real time by multi-point distributed measurement. The curved design of the sensor not only improves the connection between sensor and jumper, but also benefits to place in oven. The txt data is made to draw a graph using origin software, and the changes in temperature in the curing process are displayed intuitively. The results show that this method is simple and high-precision, and meets the testing requirements of curing temperature of explosives.

[Research on the temperature field detection method of hot forging based on long-wavelength infrared spectrum].

A temperature field detection method based on long-wavelength infrared spectrum for hot forging is proposed in the present paper. This method combines primary spectrum pyrometry and three-stage FP-cavity LCTF. By optimizing the solutions of three group nonlinear equations in the mathematical model of temperature detection, the errors are reduced, thus measuring results will be more objective and accurate. Then the system of three-stage FP-cavity LCTF was designed on the principle of crystal birefringence. The system realized rapid selection of any wavelength in a certain wavelength range. It makes the response of the temperature measuring system rapid and accurate. As a result, without the emissivity of hot forging, the method can acquire exact information of temperature field and effectively suppress the background light radiation around the hot forging and ambient light that impact the temperature detection accuracy. Finally, the results of MATLAB showed that the infrared spectroscopy through the three-stage FP-cavity LCTF could meet the requirements of design. And experiments verified the feasibility of temperature measuring method. Compared with traditional single-band thermal infrared imager, the accuracy of measuring result was improved.

Light People: Professor Laura Na Liu.

EDITORIAL: The DNA nanotechnology outlines a new chapter in biological sciences, opening a new era of scientific and technological advancements. A pioneer of DNA nanotechnology, Professor Liu from the University of Stuttgart in Germany, our latest Light People, has been working at the interface, where nanophotonics meets biology and chemistry. On the path of scientific explorations, she believes in hard working and persistency, as indicated by a line of Chinese poetry she likes, "Don't stop chasing the wind and the moon, the spring mountain is at the end of the plain." She is an outstanding female researcher, radiating wisdom. She is a pioneer in exploring the power of DNA nanotechnology and applying it to other disciplines. Meanwhile, she struggles with work-life balance. Apart from being determined and persistent, Prof. Liu is also introspective. One sees the brilliance of a scientist and the struggles of a mother, as Prof. Laura Na Liu explains to us her very personal "philosophy of life".

[Research on the temperature field detection method of large cylinder forgings during heat treatment process based on infrared spectra].

In order to grasp the changes of the forging's temperature field during heat treatment, a temperature field detection method based on infrared spectra for large cylinder forgings is proposed in the present paper. On the basis of heat transfer a temperature field model of large barrel forgings was established by the method of separating variables. Using infrared spectroscopy the large forgings temperature measurement system was built based on the three-level interference filter. The temperature field detection of forging was realized in its heat treatment by combining the temperature data and the forgings temperature field detection model. Finally, this method is feasible according to the simulation experiment. The heating forging temperature detection method can provide the theoretical basis for the correct implementation of the heat treatment process.

Light people: Nobel Laureate Prof. Eric Betzig.

EDITORIAL: Super-resolution microscopy illuminated the hazy molecular world like a beacon, bringing significant changes to the fields of biology, optics and chemistry. Eric Betzig, who shared the 2014 Nobel Prize of Chemistry with Stefan Hell and William Moerner, is one of the inventors of this fantastic scientific tool. Working originally on near field optics, Dr. Betzig made a series of stunning achievements at Bell Labs before turning 35. Yet he quit, seemingly at the top of his game, to become a hands-on dad and joined the machinery business. Eventually, he missed science so much that he made a comeback and wowed everyone instantly with his work. He defies the conventional definition of "persistence" by demonstrating an alternative route to success. Plain-speaking and earnest, Dr. Betzig is sometimes honest to almost a fault, and always believes in doing practical things. He puts his heart and soul into everything he does, because he says he wants to truly live rather than simply pass through life. In science work, he is meticulous, yet he embraces risks and believes they can bring the best out of oneself. In life, he is a loving father who is always ready to take time from his busy research work to take his children to school or tennis lessons, and a caring teacher who never forgets to command the hard work of his postdocs. Please join us for a glimpse of the Nobel laureate Eric Betzig and his extraordinary life.