Molecular Orientation Regulation of Hole Transport Semicrystalline-Polymer Enables High-Performance Carbon-Electrode Perovskite Solar Cells.

Carbon-based perovskite solar cells (PSCs) coupled with solution-processed hole transport layers (HTLs) have shown potential owing to their combination of low cost and high performance. However, the commonly used poly(3-hexylthiophene) (P3HT) semicrystalline-polymer HTL dominantly shows edge-on molecular orientation, in which the alkyl side chains directly contact the perovskite layer, resulting in an electronically poor contact at the perovskite/P3HT interface. The study adopts a synergetic strategy comprising of additive and solvent engineering to transfer the edge-on molecular orientation of P3HT HTL into 3D molecular orientation. The target P3HT HTL possesses improved charge transport as well as enhanced moisture-repelling capability. Moreover, energy level alignment between target P3HT HTL and perovskite layer is realized. As a result, the champion devices with small (0.04 cm2) and larger areas (1 cm2) deliver notable efficiencies of 20.55% and 18.32%, respectively, which are among the highest efficiency of carbon-electrode PSCs.

NiOx for interface and work function engineering in carbon-based all-inorganic perovskite solar cells.

Carbon-based all-inorganic perovskite solar cells (C-IPSCs) are stable, upscalable and have low CO2-footprint to fabricate. However, they are inefficient in converting light to electricity due to poor hole extraction at perovskite/carbon interface. Here we enable an efficient hole extraction in C-IPSCs with the aid of inorganic p-type nickel oxide nanoparticles (NiOx-NPs) at the interface and in carbon. By tailoring the work function (WF) of carbon, and reducing the energy-level misalignment at the perovskite/carbon interface, NiOx-NPs enable efficient hole transfer, reduce charge recombination and minimize energy loss. As a result, we report 15.01% and 11.02% efficiencies for CsPbI2Br and CsPbIBr2 C-IPSCs, respectively, with a high open-circuit voltage of ∼1.3 V. Unencapsulated interface-modified CsPbI2Br devices maintained 92.8% of their initial efficiency at ambient conditions after nearly 2,000 h; and 94.6% after heating at 60 °C for 170 h. This strategy to tailor carbon interface with perovskite offers an important knob in improving C-IPSCs performance.

Holistically Optimizing Charge Carrier Dynamics Enables High-Performance Dye-Sensitized Solar Cells and Photodetectors.

Charge carrier events across organic electronics are ubiquitous, and the derived optimization plays a crucial effect on improving the performance of organic electronics. Herein, a two-dimensional material (Ti3C2Tx) is incorporated into titanium dioxide (TiO2) to impart the Ti3C2Tx/TiO2 hybrid film enriched hydroxy group distribution, defect-negligible surface, upshifted work function, and enhanced conductivity yet electron mobility versus the pristine TiO2 film. Therefore, intensified photon-harvesting ability, reduced charge carrier recombination, and efficient charge carrier collection are realized for dye-sensitized solar cells (DSSCs) based on the Ti3C2Tx/TiO2 hybrid photoanode relative to control ones. Consequently, the modified DSSCs based on Z907 deliver superior efficiencies of 10.39 and 29.68% under 100 mW/cm2 illumination and ∼1.9 mW/cm2 dim light, respectively, being the highest values of Z907-based DSSCs. However, control devices only obtain lower efficiencies of 8.06 and 23.91% when undergoing the abovementioned illumination. On the other hand, the self-powered homologous photodetectors with the hybrid film as an electron-transporting layer present enhanced detectivity (1.69 × 1011 Jones) and a shortened responsivity of 0.26 s versus that of control ones (1.39 × 1011 Jones and 0.35 s). Our work implies that the Ti3C2Tx/TiO2 hybrid film features high potential for improving the performance of organic electronics for its effect of holistically optimizing charge carrier dynamics.

Synergistic Effects of Bipolar Additives on Grain Boundary-Mediated Charge Transport for Efficient Carbon-Based Inorganic Perovskite Solar Cells.

Carbon-based all-inorganic CsPbIxBr3-x perovskite solar cells offer high stability against heat and humidity and a suitable band gap for tandem and semitransparent photovoltaics. In CsPbIxBr3-x perovskite films, the defects at grain boundaries (GBs) cause charge trapping, reducing the efficiency of the cell. Electronic deactivation of GB has been a conventional strategy to suppress the trapping, but at the cost of charge carrier transport through the boundaries. Here, we turn the GBs into benign charge transport pathways with the aid of bipolar charge transport semiconductors, namely, Ti3C2TX (MXene) and Spiro-OMeTAD, respectively. Thanks to the synergistic effects of both n- and p-type transport media, the charge transport is improved and balanced at the GBs. As a result, the cells achieve an efficiency of 12.7%, the highest among all low-temperature-processed carbon-based inorganic perovskite solar cells. Benign GBs also lead to enhanced light and aging stabilities. Our work demonstrates a proof-of-concept strategy of benign electronic modulation of GBs for solution-processed perovskite solar cells.

Synthesis of MoIn2S4@CNTs Composite Counter Electrode for Dye-Sensitized Solar Cells.

A ternary and composite MoIn2S4@CNTs counter electrode (CE) with a hedgehog ball structure was synthesized by using a facile one-step hydrothermal method. The composite MoIn2S4@CNTs film possesses large specific surface area through N2 adsorption-desorption isotherms test, which is advantageous to adsorb more electrolyte and provide larger active contact area for the electrode. In addition, the composite MoIn2S4@CNTs CE exhibits low charge transfer resistance and fine electrocatalytic ability made from a series of electrochemical tests including cyclic voltammetry, electrochemical impedance, and Tafel curves. Under optimal conditions, the DSSC based on the MoIn2S4@CNTs-2 composite CE achieves an impressive power conversion efficiency as high as 8.38%, which remarkably exceeds that of the DSSCs with the MoIn2S4 CE (7.44%) and the Pt electrode (8.01%). The current work provides a simplified preparation process for the DSSCs.

Highly Efficient Quasi-Solid-State Asymmetric Supercapacitors Based on MoS2/MWCNT and PANI/MWCNT Composite Electrodes.

Molybdenum disulfide (MoS2) and polyaniline (PANI) electrodes were decorated with multi-walled carbon nanotubes (MWCNTs) on the basis of a facial hydrothermal and in situ polymerization methods and served in the asymmetric supercapacitor (ASC). The MoS2 and MWCNTs with a mole ratio of 1:1 in MoS2|MWCNTs electrode exhibited better electrochemical properties through extensive electrochemical studies, in terms of the highest specific capacitance of 255.8 F/g at 1 A/g, low internal resistance, and notable electrochemical stability with retention of the initial specific capacitance at 91.6% after 1000 cycles. The as-prepared PANI|MWCNTs electrode also exhibited good specific capacitance of 267.5 F/g at 1 A/g and remained 97.9% capacitance retention after 1000 cycles. Then, the ASC with MoS2|MWCNTs and PANI|MWCNTs composite electrodes were assembled with polyvinyl alcohol (PVA)-Na2SO4 gel electrolyte, which displayed good electrochemical performance with the specific capacitance of 138.1 F/g at 1 A/g, and remained the energy density of 15.09 Wh/kg at a high power density of 2217.95 W/kg. This result shows that this ASC device possesses excellent electrochemical properties of high energy density and power output and thus showing a potential application prospect.

Improvement in the photoelectric conversion efficiency for the flexible fibrous dye-sensitized solar cells.

A dye-sensitized and flexible TiO2 fiber with multilayer structure was prepared by using brush method as the photoanode in the efficient flexible fibrous dye-sensitized solar cells (FFDSSCs) to avoid electronic recombination and improve the electronic capture efficiency. The composite Pt counter electrode, preparation from the surface modification of the electrodeposited Pt wire by using a simple one-step thermal decomposition approach of H2PtCl6 isopropanol and n-butyl alcohol (volume ratio = 1:1) solution, provided a significant improvement in electrocatalytic activity, which was confirmed by extensive electrochemical tests. The FFDSSC assembled with the fiber-shaped TiO2 photoanode and the composite Pt counter electrode achieves an enhanced photoelectric conversion efficiency of 6.35%, higher than that of the FFDSSC with monolayer fibrous TiO2 photoanode and electrodeposited Pt wire counter electrode. More importantly, the photoelectric conversion efficiency of 6.35% is comparable to that of the FFDSSC based on the pure Pt wire counter electrode (6.32%). The FFDSSC with high elasticity, flexibility, and stretchability can adapt to complex mechanical deformations, which is of great significance for the development of wearable electronics in the future.

UV Treatment of Low-Temperature Processed SnO2 Electron Transport Layers for Planar Perovskite Solar Cells.

We report a new method as UV treatment of low-temperature processed to obtain tin oxide (SnO2) electron transport layers (ETLs). The results show that the high quality of ETLs can be produced by controlling the thickness of the film while it is treated by UV. The thickness is dependent on the concentration of SnO2. Moreover, the conductivity and transmittance of the layer are dependent on the quality of the film. A planar perovskite solar cell is prepared based on this UV-treated film. The temperatures involved in the preparation process are less than 90 °C. An optimal power conversion efficiency of 14.36% is obtained at the concentration of SnO2 of 20%. This method of UV treatment SnO2 film at low temperature is suitable for the low-cost commercialized application.

Efficient Nickel Sulfide and Graphene Counter Electrodes Decorated with Silver Nanoparticles and Application in Dye-Sensitized Solar Cells.

We reported a facile two-step electrochemical-chemical approach for in situ growth of nickel sulfide and graphene counter electrode (CE) decorated with silver nanoparticles (signed NiS/Gr-Ag) and served in dye-sensitized solar cells (DSSCs). Under optimum conditions, the DSSC achieved a remarkable power conversion efficiency of 8.36 % assembled with the NiS/Gr-Ag CE, much higher than that based on the Pt CE (7.76 %). The surface morphology of NiS/Gr-Ag CE exhibited a smooth surface with cross-growth of NiS, graphene, and Ag nanoparticles, which was beneficial to the fast mass transport of electrolytes; increased the contact area of electrolytes and active materials; and enabled to speed up the reduction of triiodide to iodide. The research on the electrochemical properties also showed that the NiS/Gr-Ag CE possessed lower charge transfer resistance and more excellent electrocatalytic activity in iodide/triiodide electrolyte compared to the Pt electrode.

Efficient Dye-Sensitized Solar Cells Made from High Catalytic Ability of Polypyrrole@Platinum Counter Electrode.

Polypyrrole@platinum (PPy@Pt) composite film was successfully synthesized by using a one-step electrochemical method and served as counter electrode (CE) for efficient dye-sensitized solar cells (DSSCs). The PPy@Pt CE with one-dimensional structure exhibited excellent electrocatalytic activity and superior charge transfer resistance for I(-)/I3 (-) electrolyte after being the cyclic voltammetry and electrochemical impedance spectroscopy tested. The photocurrent-photovoltage curves were further used to calculate the theoretical photoelectric performance parameters of the DSSCs. The DSSC based on the PPy@Pt CE achieved a remarkable power conversion efficiency of 7.35 %, higher about 19.9 % than that of conventional Pt CE (6.13 %). This strategy provides a new opportunity for fabricating low-cost and highly efficient DSSCs.

A highly efficient flexible dye-sensitized solar cell based on nickel sulfide/platinum/titanium counter electrode.

A composite film of nickel sulfide/platinum/titanium foil (NiS/Pt/Ti) with low cost and high electrocatalytic activity was synthesized by the use of an in situ electropolymerization route and proposed as a counter electrode (CE) catalyst for flexible dye-sensitized solar cells (FDSSCs). The FDSSC with the NiS/Pt/Ti CE exhibited a comparable power conversion efficiency of 7.20% to the FDSSC with the platinum/titanium (Pt/Ti) CE showing 6.07%. The surface morphology of the NiS/Pt/Ti CE with one-dimensional (1D) structure is characterized by using the scanning electron microscopy (SEM). The NiS/Pt/Ti CE also displayed multiple electrochemical functions of excellent conductivity, great electrocatalytic ability for iodine/triiodine, and low charge transfer resistance of 2.61 ± 0.02 Ω cm(2), which were characterized by using the cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and Tafel polarization plots. The photocurrent-photovoltage (J-V) character curves were further used to calculate the theoretical optical light performance parameters of the FDSSCs. It may be said that the NiS/Pt/Ti counter electrode is a promising catalytic material to replace the expensive platinum in FDSSCs.

Semitransparent inverted polymer solar cells employing a sol-gel-derived TiO2 electron-selective layer on FTO and MoO3/Ag/MoO3 transparent electrode.

We report a new semitransparent inverted polymer solar cell (PSC) with a structure of glass/FTO/nc-TiO2/P3HT:PCBM/MoO3/Ag/MoO3. Because high-temperature annealing which decreased the conductivity of indium tin oxide (ITO) must be handled in the process of preparation of nanocrystalline titanium oxide (nc-TiO2), we replace glass/ITO with a glass/fluorine-doped tin oxide (FTO) substrate to improve the device performance. The experimental results show that the replacing FTO substrate enhances light transmittance between 400 and 600 nm and does not change sheet resistance after annealing treatment. The dependence of device performances on resistivity, light transmittance, and thickness of the MoO3/Ag/MoO3 film was investigated. High power conversion efficiency (PCE) was achieved for FTO substrate inverted PSCs, which showed about 75% increase compared to our previously reported ITO substrate device at different thicknesses of the MoO3/Ag/MoO3 transparent electrode films illuminated from the FTO side (bottom side) and about 150% increase illuminated from the MoO3/Ag/MoO3 side (top side).

Bifacial dye-sensitized solar cells: a strategy to enhance overall efficiency based on transparent polyaniline electrode.

Dye-sensitized solar cell (DSSC) is a promising solution to global energy and environmental problems because of its clean, low-cost, high efficiency, good durability, and easy fabrication. However, enhancing the efficiency of the DSSC still is an important issue. Here we devise a bifacial DSSC based on a transparent polyaniline (PANI) counter electrode (CE). Owing to the sunlight irradiation simultaneously from the front and the rear sides, more dye molecules are excited and more carriers are generated, which results in the enhancement of short-circuit current density and therefore overall conversion efficiency. The photoelectric properties of PANI can be improved by modifying with 4-aminothiophenol (4-ATP). The bifacial DSSC with 4-ATP/PANI CE achieves a light-to-electric energy conversion efficiency of 8.35%, which is increased by ~24.6% compared to the DSSC irradiated from the front only. This new concept along with promising results provides a new approach for enhancing the photovoltaic performances of solar cells.

A new method to disperse CdS quantum dot-sensitized TiO2 nanotube arrays into P3HT:PCBM layer for the improvement of efficiency of inverted polymer solar cells.

We report that the efficiency of ITO/nc-TiO2/P3HT:PCBM/MoO3/Ag inverted polymer solar cells (PSCs) can be improved by dispersing CdS quantum dot (QD)-sensitized TiO2 nanotube arrays (TNTs) in poly (3-hexylthiophene) and [6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM) layer. The CdS QDs are deposited on the TNTs by a chemical bath deposition method. The experimental results show that the CdS QD-sensitized TNTs (CdS/TNTs) do not only increase the light absorption of the P3HT:PCBM layer but also reduce the charge recombination in the P3HT:PCBM layer. The dependence of device performances on cycles of CdS deposition on the TNTs was investigated. A high power conversion efficiency (PCE) of 3.52% was achieved for the inverted PSCs with 20 cyclic depositions of CdS on TNTs, which showed a 34% increase compared to the ITO/nc-TiO2/P3HT:PCBM/MoO3/Ag device without the CdS/TNTs. The improved efficiency is attributed to the improved light absorbance and the reduced charge recombination in the active layer.

An ultraviolet responsive hybrid solar cell based on titania/poly(3-hexylthiophene).

Here we present an ultraviolet responsive inorganic-organic hybrid solar cell based on titania/poly(3-hexylthiophene) (TiO(2)/P3HT) heterojuction. In this solar cell, TiO(2) is an ultraviolet light absorber and electronic conductor, P3HT is a hole conductor, the light-to-electrical conversion is realized by the cooperation for these two components. Doping ionic salt in P3HT polymer can improve the photovoltaic performance of the solar cell. Under ultraviolet light irradiation with intensity of 100 mW·cm(-2), the hybrid solar cell doped with 1.0 wt.% lithium iodide achieves an energy conversion efficiency of 1.28%, which is increased by 33.3% compared to that of the hybrid solar cell without lithium iodide doping. Our results open a novel sunlight irradiation field for solar energy utilization, demonstrate the feasibility of ultraviolet responsive solar cells, and provide a new route for enhancing the photovoltaic performance of solar cells.

Dual functions of YF3:Eu³âº for improving photovoltaic performance of dye-sensitized solar cells.

In order to enhance the photovoltaic performance of dye-sensitized solar cell (DSSC), a novel design is demonstrated by introducing rare-earth compound europium ion doped yttrium fluoride (YF3:Eu³âº) in TiO2 film in the DSSC. As a conversion luminescence medium, YF3:Eu³âº transfers ultraviolet light to visible light via down-conversion, and increases incident harvest and photocurrent of DSSC. As a p-type dopant, Eu³âº elevates the Fermi level of TiO2 film and thus heightens photovoltage of the DSSC. The conversion luminescence and p-type doping effect are demonstrated by photoluminescence spectra and Mott-Schottky plots. When the ratio of YF3:Eu³âº/TiO2 in the doping layer is optimized as 5 wt.%, the light-to-electric energy conversion efficiency of the DSSC reaches 7.74%, which is increased by 32% compared to that of the DSSC without YF3:Eu³âº doping. Double functions of doped rare-earth compound provide a new route for enhancing the photovoltaic performance of solar cells.

Glucose aided preparation of tungsten sulfide/multi-wall carbon nanotube hybrid and use as counter electrode in dye-sensitized solar cells.

The tungsten sulfide/multi-wall carbon nanotube (WS(2)/MWCNT) hybrid was prepared in the presence of glucose by the hydrothermal route. The hybrid materials were used as counter electrode in the dye-sensitized solar cell (DSSC). The results of cyclic voltammetry measurement and electrochemical impedance spectroscopy indicated that the glucose aided prepared (G-A) WS(2)/MWCNT electrode had low charge-transfer resistance (R(ct)) and high electrocatalytic activity for triiodide reduction. The excellent electrochemical properties for (G-A) WS(2)/MWCNT electrode is due to the synergistic effects of WS(2) and MWCNTs, as well as amorphous carbon introduced by glucose. The DSSC based on the G-A WS(2)/MWCNT counter electrode achieved a high power conversion efficiency of 7.36%, which is comparable with the performance of the DSSC using Pt counter electrode (7.54%).

A large-area light-weight dye-sensitized solar cell based on all titanium substrates with an efficiency of 6.69% outdoors.

Light-weight PEDOT-Pt/Ti mesh and Ti/TiO(2) foil electrodes are prepared. Owing to the PEDOT-Pt/Ti photocathode's high transparency, good electrocatalytic activity, and low resistance; the Ti/TiO(2) anode's large specific area and high conductivity, a light-weight backside illuminated large-area (100 cm(2) ) dye-sensitized solar cell achieves an energy conversion efficiency of 6.69% under an outdoors sunlight irradiation of 55 mW cm(-2) .

Application of Y(2)O(3):Er(3+) nanorods in dye-sensitized solar cells.

Y(2)O(3):Er(3+) nanorods are synthesized by means of a hydrothermal method and then introduced into a TiO(2) electrode in a dye-sensitized solar cell (DSSC). Y(2)O(3):Er(3+) improves infrared light harvest via up-conversion luminescence and increases the photocurrent of the DSSC. The rare earth ions improve the energy level of the TiO(2) electrode through a doping effect and thus increase the photovoltage. The light scattering is ameliorated by the one-dimensional nanorod structure. The DSSC containing Y(2)O(3):Er(3+) (5 wt%) in the doping layer achieves a light-to-electric energy conversion efficiency of 7.0%, which is an increase of 19.9% compared to the DSSC lacking of Y(2)O(3):Er(3+).