RESUMO
We proposed and demonstrated mode cleaning in a high-power fiber laser by integrating an anti-resonant hollow-core fiber (AR-HCF) into a multimode laser cavity of an ytterbium (Yb)-doped fiber (YDF). An in-house mode-matched AR-HCF was fusion-spliced to a commercial multimode LMA-YDF, ensuring efficient fundamental mode coupling. The AR-HCF inflicts a high propagation loss selectively on higher-order modes, facilitating fundamental mode operation. Thus, the AR-HCF works as an efficient spatial mode filter embedded in the multimode fiber laser cavity and reinforces preferential amplification of the fundamental mode. Beam quality factor enhancement was achieved from M2 = 2.09 to 1.39 at an output power of 57.7 W (pump-power limited). The beam quality can be further improved by refining the AR-HCF fabrication. The proposed technique has a great potential to be exploited in other multimode fiber laser cavities involving erbium- or thulium-doped fibers and obviates the need for complicated specialty active fiber designs. Compared with the commonly used fiber bending technique, our method can achieve an efficient higher-order mode suppression without inducing mode-field deterioration.
RESUMO
We report a linearly polarized ytterbium-doped fiber (YDF) laser cavity configured by integrating an antiresonant hollow-core fiber-based inline polarizer. The 5-cm-long compact fiber polarizer was fusion spliced to a commercial large-mode-area, polarization-maintaining YDF. Near-diffraction-limited linearly polarized signal output with a polarization extinction ratio of > 21â dB was achieved for up to 25 W of power that was limited only by the available pump power. The performance of the hollow-core fiber polarizer was found to be temperature insensitive, which obviates the need for the precise temperature control required in all-fiber, high-power polarized laser cavities employing crossed fiber Bragg gratings. We used the tapering technique to scale down the geometry of the polarizing fiber and shift its operating wavelength by â¼100â nm, which makes it an attractive candidate for a variety of fiber laser applications.
RESUMO
We present an efficient 976 nm laser generation from an ytterbium (Yb)-doped step-index multicore fiber (MCF) with six cores placed in a ring shape. Each of the six cores has a large-mode-area (LMA) and a low numerical aperture (NA), which makes the MCF equipped with the features of a large core-to-cladding area ratio and differential bending loss for wavelength and mode selection. Hence, the Yb-doped MCF benefits 976 nm laser generation by simultaneously suppressing unwanted 1030 nm emission and higher-order modes (HOMs). A 976 nm laser is obtained in a short piece (88 cm) of the Yb MCF, with a good slope efficiency of 46% with respect to launched pump power and the maximum output power of 25 W (pump power limited). A mode area of 1432 µm2 at the 976 nm is expected for the fundamental in-phase mode.
RESUMO
We investigate mode-area scaling by means of supermode operation in an all-solid multicore fiber. To obtain a large-mode area (LMA), we designed and fabricated an active double-clad multicore fiber, where each ytterbium-doped core is 19 µm in diameter and has a numerical aperture of 0.067, comparable to the core of the largest available commercial LMA fibers. The six large cores are stacked tightly in a ring structure to enable phase locking of the core fields and supermode operation. The fiber laser performance was investigated in a linear laser cavity with an external Talbot resonator for mode selection. The highest output power achieved was 115 W with an overall 61% slope efficiency corresponding to the pump power. The measured M2 was 1.43 for the central lobe with nearly 70% of the total power.
RESUMO
Hollow-core anti-resonant fiber technology has made a rapid progress in low loss broadband transmission, enabled by its much reduced light-material overlap. This unique characteristic has driven emerging of new applications spanning from extreme wavelength generation to beam delivery. The successful demonstrations appear to suggest progression of the technology toward device level development and all-fiberized systems. We investigate this opportunity and report an in-fiber interferometer built in a dual hollow-core anti-resonant fiber. By placing multiple air cores in a single fiber, coherently interacting transverse modes are excited, which becomes a basis of an interferometer. We use this hollow core based inherent supermodal interaction to demonstrate highly sensitive in-fiber interferometer. Unique combination of the air guidance and the supermodal interaction offers robust, simple yet highly sensitive interferometer with suppressed temperature cross-talk that has been an enduring problem in fiber strain sensing applications. The in-fiber interferometer is further investigated as a sensing element for pressure measurement based on an interferometric phase change upon external strain. The interferometer features 39.3 nm/MPa of ultrahigh sensitivity with 0.14 KPa/°C of negligible gas pressure temperature crosstalk. The performance, which is much improved from prior fiber sensors, testifies advances of hollow core fiber technology toward a device level.