Three-dimensional orientation and location-dependent varying rules of radiographic angles of the acetabular cup.

AIM: The aim of this study is to demonstrate the varying rules of radiographic angles following varying three-dimensional (3D) orientations and locations of cup using an accurate mathematical model. METHODS: A cone model is established to address the quantitative relationship between the opening circle of cup and its ellipse projection on radiograph. The varying rules of two-dimensional (2D) radiographic anteversion (RA) and inclination (RI) angles can be analyzed. RESULTS: When the centre of cup is located above X-ray source, with proper 3D RI/RA angles, 2D RA angle can be equal to its 3D counterpart, and 2D RI angle is usually greater than its 3D counterpart. Except for the original point on hip-centered anterior-posterior radiograph, there is no area on radiograph where both 2D RA and RI angles are equal to their 3D counterparts simultaneously. DISCUSSION: This study proposes an innovative model for accurately explaining how 2D RA/RI angles of cup are varying following different 3D RA/RI angles and location of cup. The analysis results provide clinicians an intuitive grasp of knowledge about 2D RA/RI angles greater or smaller than their 3D counterparts post-operatively. The established model may allow determining the effects of pelvic rotations on 2D radiographic angles of cup.

Experimental study on treatment of acetabular anterior column fractures: applyment of a minimally invasive percutaneous lag screw guide apparatus.

BACKGROUND: The aim of this study was to design a new minimally invasive percutaneous lag screw guide apparatus and to verify its adjuvant treatment of acetabular anterior column fracture on pelvis specimens. METHODS: This guide apparatus was self-developed based on the principles of "two points form a line" and "Rectangle". Using C-arm fluoroscopy, this guide apparatus was used to conduct minimally invasive percutaneous lag screw internal fixation of acetabular anterior column fractures. Ten hollow lag screws were placed into 5 pelvis specimens. RESULT: Result showed no sign of any screws puncturing the cortex or entering into the hip joint on radiological assessment. The cross-section reconstructed vertical distance to the screw, on the cross-section acetabular notch and the cross-section of the screw where the distance of between the screw and the iliopectineal line's arc roof was at its shortest, indicate that at all points (T, R-r) under the line with an inclination of 1 (namely T = R-r) the screw is within the cortex and does not puncture the acetabula anterior column or enter into the hip joint. CONCLUSIONS: We may conclude that this self-developed guide apparatus solves the screw precision problem during the treatment of acetabular anterior column fractures through a minimally invasive percutaneous lag screw.

The development of dual-label time-resolved fluorescence immunoassay (TRFIA) for screening of ovarian cancer based on simultaneous detection of human epididymis protein-4 and cancer antigen 125.

A two-step dual-label TRFIA was developed for the simultaneous detection of human epididymis protein-4 and cancer antigen 125 in a single run. The performance of this assay was first evaluated using clinical serum samples, and then compared with commercialized kits. The sensitivity of this assay for cancer antigen 125 detection was 0.5 U/mL (dynamic range, 0-1400 U/L), and the sensitivity for human epididymis protein-4 detection was 1 pM (dynamic range, 1-900 pM). High correlation coefficients (R) were obtained between the present dual-label TRFIA and commercially available kits (R = 0.99). The present dual-label TRFIA has high sensitivity, specificity, and accuracy in clinical sample analysis. It is a good alternative to the single-label diagnostic methods.

A computer aided measurement method for unstable pelvic fractures based on standardized radiographs.

BACKGROUND: To set up a method for measuring radiographic displacement of unstable pelvic ring fractures based on standardized X-ray images and then test its reliability and validity using a software-based measurement technique. METHODS: Twenty-five patients that were diagnosed as AO/OTA type B or C pelvic fractures with unilateral pelvis fractured and dislocated were eligible for inclusion by a review of medical records in our clinical centre. Based on the input pelvic preoperative CT data, the standardized X-ray images, including inlet, outlet, and anterior-posterior (AP) radiographs, were simulated using Armira software (Visage Imaging GmbH, Berlin, Germany). After representative anatomic landmarks were marked on the standardized X-ray images, the 2-dimensional (2D) coordinates of these points could be revealed in Digimizer software (Model: Mitutoyo Corp., Tokyo, Japan). Subsequently, we developed a formula that indicated the translational and rotational displacement patterns of the injured hemipelvis. Five separate observers calculated the displacement outcomes using the established formula and determined the rotational patterns using a 3D-CT model based on their overall impression. We performed 3D reconstruction of all the fractured pelvises using Mimics (Materialise, Haasrode, Belgium) and determined the translational and rotational displacement using 3-matic suite. The interobserver reliability of the new method was assessed by comparing the continuous measure and categorical outcomes using intraclass correlation coefficient (ICC) and kappa statistic, respectively. RESULT: The interobserver reliability of the new method for translational and rotational measurement was high, with both ICCs above 0.9. Rotational outcome assessed by the new method was the same as that concluded by 3-matic software. The agreement for rotational outcome among orthopaedic surgeons based on overall impression was poor (kappa statistic, 0.250 to 0.426). Compared with the 3D reconstruction outcome, the interobserver reliability of the formula method for translational and rotational measures was perfect with both ICCs more than 0.9. CONCLUSIONS: The new method for measuring displacement using a formula was reliable, and could minimise the measurement errors and maximise the precision of pelvic fracture description. Furthermore, this study was useful for standardising the operative plan and establishing a theoretical basis for robot-assisted pelvic fracture surgery based on 2-D radiographs.

Dependable Automated Approach for Measuring the Retrograde Superior Ramus Screw Corridor in Pelvic Fracture Fixation.

BACKGROUND: Precise measurement of the intraosseous corridor within the superior pubic ramus is essential for the accurate percutaneous placement of a retrograde superior ramus screw (SRS). However, conventional manual measurement methods are often subjective, leading to variations in results among observers. Our goal was to develop an automated and dependable method for determining the retrograde SRS corridor. METHODS: We developed an automated technique that utilized a computed tomography (CT) image-based search algorithm to identify the retrograde SRS corridor with the maximum diameter. We evaluated the reliability of this automated approach in comparison to a manual method using 17 pelves. Subsequently, we used both methods to measure the diameter, length, and orientation of the retrograde SRS corridor in 204 pelves in a Chinese population and assessed the intra- and interobserver agreement of each method by calculating the root-mean-square error (RMSE) and constructing Bland-Altman plots. We determined the screw applicability (percentages of hemipelves that could be treated with specific sizes of screws) for each method. Additionally, we investigated potential factors influencing the corridor, such as sex, age, height, and weight, through regression analysis. RESULTS: The intra- and interobserver intraclass correlation coefficients (ICCs) for the automated method (0.998 and 0.995) were higher than those for the manual approach (0.925 and 0.918) in the assessment of the corridor diameter. Furthermore, the diameter identified by the automated method was notably larger than the diameter measured with the manual method, with a mean difference and RMSE of 0.9 mm and 1.1 mm, respectively. The automated method revealed a significantly smaller corridor diameter in females than in males (an average of 7.5 and 10.4 mm, respectively). Moreover, use of the automated method allowed 80.6% of the females to be managed with a 4.5-mm screw while a 6.5-mm screw could be utilized in 19.4%, surpassing the capabilities of the manual method. Female sex had the most substantial impact on corridor diameter (ß = -0.583). CONCLUSIONS: The automated method exhibited better reliability than the manual method in measuring the retrograde SRS corridor, and showed a larger corridor diameter for screw placement. Females had a significantly smaller corridor diameter than males. Given the intricate nature of the automated approach, which entails utilizing different software and interactive procedures, our current method is not readily applicable for traumatologists. We are working on developing integrated software with the goal of providing a more user-friendly solution for traumatologists in the near future. LEVEL OF EVIDENCE: Diagnostic Level III. See Instructions for Authors for a complete description of levels of evidence.

Biomechanical Research of Three Parallel Cannulated Compression Screws in Oblique Triangle Configuration for Fixation of Femoral Neck Unstable Fractures.

OBJECTIVE: Surgical treatment with internal fixation, specifically percutaneous fixation with three cannulated compression screws (CCSs), is the preferred choice for young and middle-aged patients. The mechanical advantage of the optimal spatial configuration with three screws provides maximum dispersion and cortical support. We suspect that the spatial proportion of the oblique triangle configuration (OTC) in the cross-section of the femoral neck isthmus (FNI) may significantly improve shear and fatigue resistance of the fixed structure, thereby stabilizing the internal fixation system in femoral neck fracture (FNF). This study aims to explore the mechanical features of OTC and provide a mechanical basis for its clinical application. METHODS: Twenty Sawbone femurs were prepared as Pauwels type III FNF models and divided equally into two fixation groups: OTC and inverted equilateral triangle configuration (IETC). Three 7.3 mm diameter cannulated compression screws (CCSs) were used for fixation. The specimens of FNF after screw internal fixation were subjected to static loading and cyclic loading tests, respectively, with five specimens for each test. Axial stiffness, 5 mm failure load, ultimate load, shear displacement, and frontal rotational angle of two fragments were evaluated. In the cyclic loading test, the load sizes were 700 N, 1400 N, and 2100 N, respectively, and the fracture end displacement was recorded. Results were presented as means ± SD. Data with normal distributions were compared by the Student's t test. RESULTS: In the static loading test, the axial stiffness, ultimate load, shear displacement, and frontal rotational angle of two fragments were (738.64 vs. 620.74) N/mm, (2957.61 vs. 2643.06) N, (4.67 vs. 5.39) mm, and (4.01 vs. 5.52)° (p < 0.05), respectively. Comparison between the femoral head displacement after 10,000 cycles of 700N cyclic loading and total displacement after 20,000 cycles of 700-1400N cyclic loading showed the OTC group was less than the IETC group (p < 0.05). A comparison of femoral head displacement after 10,000 cycles of 1400N and 2100N cycles and total displacement after 30,000 cycles of 700-2100N cycles showed the OTC group was less than another group, but the difference was not significant (p > 0.05). CONCLUSION: When three CCSs are inserted in parallel to fix FNF, the OTC of three screws has obvious biomechanical advantages, especially in shear resistance and early postoperative weight-bearing, which provides a mechanical basis for clinical selection of ideal spatial configuration for unstable FNF.

[Biological changes after axonal stretch and their mechanisms].

Research on peripheral nervous injuries, especially the stretched injuries, is important to improve the clinical effectiveness and alleviate the patients's pain. In recent years, the biological changes and mechanics of stretched axons have been hot topics. This article reviews the recent advances in the morphological changes of axons as well as changes in cellular membrane, cytoskeleton, cellular metabolism, and action potential after axonal stretch.

Intramedullary nailing versus plating fixation for the treatment of midshaft clavicular fractures: A meta-analysis of randomized controlled trials.

PURPOSE: This study was to test the hypothesis that intramedullary (IM) nailing fixation of midshaft clavicle fractures could result in better clinical outcomes and lower complications rates than plating fixation. METHODS: PubMed, Embase, and the Cochrane Library database were used to search all English language published randomized controlled trials (RCTs) of midshaft clavicle fractures using plating versus IM nailing. The characteristics of the study participants were collected. Outcomes of postoperative shoulder functional measurements, operative data and complications rates were meta-analyzed. RESULTS: Eight hundred and ninety-five patients in ten RCTs and three quasi-RCTs were involved in the meta-analysis. The results of meta-analysis of these studies showed that the functional outcome evaluated by the Constant Shoulder and Disabilities of the Arm, Shoulder and Hand (DASH) scores after accepting IM nailing was significantly better than that of plating fixation at one year post-operatively (P < 0.01), with the heterogeneity of 43% and 91%, respectively. Sensitivity analyses of the pooled results of Constant and DASH scores displayed that the functional advantage of IM nailing fixation comes from the subgroup of locked IM nailing. Further, regarding the operative statistics, operative time, blood loss and wound length were significantly less in the IM nailing group than the plating group (P < 0.001). The rates of infection, major complications and complications-related revision surgery were significantly higher in the plating group than the IM nailing group; however, there were no significantly statistical differences in other complications, e.g., nonunion, refracture after hardware removal, implant failure, symptomatic hardware, etc. (P > 0.05). CONCLUSION: The observations in this review suggested that IM nailing, especially locked IM nailing, could provide better shoulder functional outcome at one-year follow-up. Moreover, IM nailing fixation could effectively reduce operative time, blood loss, rates of infection, major complications, and revision surgery than plating. Further high-quality clinical trials with large samples and consistent designs are still needed to verify the long-term functional advantage of locked and unlocked IM nailing for midshaft clavicle fractures. LEVEL OF EVIDENCE: Level II.

ASCC3 promotes the immunosuppression and progression of non-small cell lung cancer by impairing the type I interferon response via CAND1-mediated ubiquitination inhibition of STAT3.

BACKGROUND: Activating signal cointegrator 3 (ASCC3) has been identified as an oncogenic factor that impairs host immune defense. However, the underlying mechanisms of carcinogenesis and its impact on the antitumor immune response remain unclear. In this study, we aimed to investigate the molecular mechanisms of ASCC3 in the progression of non-small cell lung cancer (NSCLC). METHODS: Single-cell sequencing data from the Gene Expression Omnibus and gene expression profiles from The Cancer Genome Atlas database were analyzed. The expression, clinical relevance and biological functions of ASCC3 in NSCLC were explored. Then, RNA sequencing, immunoprecipitation, mass spectrometry, immunofluorescence, and flow cytometry analyses were conducted to explore the underlying molecular mechanisms. In addition, in vivo experiments in mouse models were conducted to explore the probability of ASCC3 knockdown to improve the efficacy of anti-Programmed Death-1 (PD-1) therapy in NSCLC. RESULTS: ASCC3 was significantly upregulated in NSCLC and correlated with poor pathological characteristics and prognosis in patients with NSCLC. Overexpression of ASCC3 promoted malignant phenotypes of NSCLC cells and induced an immunosuppressive tumor microenvironment, which was characterized by a decrease in CD8+ T cells, natural killer cells and dendritic cells but an increase in regulatory T(Treg) cells. Mechanistically, ASCC3 stabilized signal transducer and activator of transcription (STAT)3 signaling by recruiting Cullin-associated and neddylation dissociated 1 (CAND1), which inhibited ubiquitin-mediated degradation of STAT3, thereby impairing the type I interferon response of tumor cells and promoting the immunosuppression and progression of NSCLC. Furthermore, high expression of ASCC3 impaired the efficacy of anti-PD-1 therapy, and an anti-PD-1 antibody combined with ASCC3 knockdown exerted promising synergistic efficacy in a preclinical mouse model. CONCLUSION: ASCC3 could stabilize the STAT3 pathway via CAND1, reshaping the tumor microenvironment and inducing resistance to anti-PD-1 therapy, which promotes the progression of NSCLC. It is a reliable prognostic indicator and can be a target in combination therapy for NSCLC.

Comparison of oblique triangular configuration and inverted equilateral triangular configuration of three cannulated screws in treating unstable femoral neck fracture: A finite element analysis.

BACKGROUND: The cross-sectional area of three parallel screws might affect the stability of the internal fixation of femoral neck fractures. The screws fixed in the oblique-triangle configuration (OTC) were assumed to have a larger cross-sectional area, but the biomechanical stability has not yet been validated. In this study, finite element analyses were performed to compare the biomechanical properties of the internal fixation fixed by the OTC and the traditional Inverted Equilateral Triangle Configuration (IETC). METHOD: Pauwels type III fracture was established on the three-dimensional femoral model and three cannulated screws with the OTC and traditional IETC methods were applied. The oblique-triangle configuration with the largest area inscribed the femoral neck isthmus by the three screws was determined, the area and circumference of the cross-section formed by the OTC and IETC model were compared. Stress, strain, and displacement peaks of the two configuration models under different loads were compared. Twelve pairs of nodes on the fracture ends were selected and the displacement of the fracture ends was evaluated through the displacement between these nodes. RESULTS: The area and circumference of the cross-section formed by the OTC were larger than those in the IETC model. The degree of stress dispersion around the screw holes in the OTC model was better than that of the IETC, but the stress distribution order of the three screws in the two models was consistent. The maximum stress, strain, displacement, and displacement of the fracture end in the OTC model were smaller than those in the IETC model. The stress, strain, displacement, and fracture end displacement peaks of the two fixed models gradually increase with the increase of loads. CONCLUSION: The oblique-triangle configuration showed superior mechanical properties than the IETC in finite element analyses. This study suggests that when three screws are fixed in parallel method, the larger the cross-sectional area of the screw configuration, the better stability of the internal fixation might be obtained. Furthermore, the biomechanical properties of various spatial configurations and screw holes of the three parallel screws need to be considered before clinical practice.

The oblique triangle configuration of three parallel screws for femoral neck fracture fixation using computer-aided design modules.

Closed reduction and internal fixation with three cannulated compression screws is a common method for treating femoral neck fractures in young and middle-aged patients. Protocols including the inverted triangle configuration and dispersion of the screws still needed further supports. The purpose of this study was to explore a novel oblique triangle configuration (OTC) of three screws in fixing femoral neck fractures based on the morphology of the femoral neck isthmus (FNI). The computer-aided design modules were used to explore the ideal spatial configuration with largest triangle by three parallel screws. A univariate evaluation model was established based on the oval-like cross-section of the FNI. When the three screws were positioned by the OTC, Inverted Equilateral Triangle Configuration (IETC), and the Maximum Area Inverted Isosceles Triangle Configuration (MA-IITC) respectively, the proportion of area and circumference in the cross-section of FNI and the changing trend of proportion were compared under various torsion angles, eccentricity, and cross-sectional area of FNI. The area and circumference ratios of the parallel screws using the OTC method were significantly higher than in the IETC and MA-IITC groups. In the univariate evaluation model, the OTC area ratio and circumference ratio remained stable under the different femoral neck torsion angles, FNI cross-sectional area, and eccentricity. The OTC method provided an ideal spatial configuration for the FNA fixation with the largest area using three parallel screws. The position of the posterior screw was also away from the metaphyseal artery, potentially reducing the possibility of vascular injury and screw penetrating.

[Properties evaluation of collagen-hydroxyapatite-chondroitin sulfate-bone morphogenetic protein bone substitute material].

OBJECTIVE: To construct a new 3D porous bone substitute material with collagen, hydroxyapatite and chondroitin sulfate, which has the main components of nature bone and the cell growth factor BMP-2 with bone inductive ability. METHODS: Collagen-hydroxyapatite-chondroitin sulfate scaffolds were prepared by chemical cross linking and freeze-drying, and bone morphogenetic protein (BMP) was incorporated into the scaffolds by adsorption. The bone substitute material was investigated by HE analysis, scanning electron microscope(SEM), electron spectroscopy for chemical analysis(ESCA), and X-ray diffraction(XRD). Rat mesenchymal stem cells (MSCs) were seeded into the scaffolds and cultured to form cell/scaffold (CS) constructs in vitro. The ectopic osteoinduction of the scaffolds were evaluated in vivo. RESULTS: The bone substitute material had a porous 3D structure facilitating cells growing into it. Implanted into the muscle, the scaffolds were degraded with the forming of new bone. CONCLUSION: Our Findings indicate that the bone substitute material has good biocompatibility and its attachment to CS could improve the adhesion and differentiation of cells.

The Oval-like Cross-section of Femoral Neck Isthmus in Three-dimensional Morphological Analysis.

OBJECTIVES: To investigate the cross-section shape of the femoral neck isthmus (FNI) in three-dimensional reconstruction model of the femoral neck. METHODS: From December 2009 to December 2012, computed tomography (CT) data of bilateral hip joint from 200 consecutive patients (137 males and 63 females, 69.41 ± 9.21 years old, ranged from 50-85 years old) who underwent surgical treatments for proximal femoral fracture were retrospectively reviewed. The 3D model of the proximal femur was reconstructed, and the "inertia axis" method, which was applied to measure the long and short axes of the cross-section of the FNI, was established. The cross-sectional area and perimeter were calculated by a formula using the length of the long and short axes and then compared with the actual measured values by the software. Correlation between the descriptive parameters of the FNI cross-section (area, perimeter, and eccentricity) and patients' demographics (age, height, and weight) was analyzed. Stepwise linear regression analysis was used to determine the main relevant factors. RESULTS: The ICC results showed excellent data reproducibility ranged from 0.989 to 0.996. There was no significant difference in the cross-sectional area of the FNI between the actual measured values and the predicted values using the formula (732.83 ± 126.74 mm2 vs 731.62 ± 128.15 mm2 , P = 0.322). The perimeter using the two methods showed narrow while significant difference (97.86 ± 8.60 mm vs 92.84 ± 8.65 mm, P < 0.001), the actual measured values were about 5 mm greater than the predicted values. The parameters (area, perimeter, and eccentricity) were significantly larger in male than female (P < 0.001). A positive correlation between the cross-sectional area, perimeter, height, and weight was observed. The stepwise linear regression analysis showed that the regression equation of the FNI area was as follows: Y = -1083.75 + 1033.86 × HEIGHT + 1.92 × WEIGHT, R2 = 0.489. CONCLUSION: The cross-section shape of the FNI appears to be oval-like in the 3D model, which is separated according to the inertia axis, and the findings proposed an anatomical basis for the further study of the spatial configuration of cannulated screws in the treatment of femoral neck fractures.

Epidural electrical stimulation effectively restores locomotion function in rats with complete spinal cord injury.

Epidural electrical stimulation can restore limb motor function after spinal cord injury by reactivating the surviving neural circuits. In previous epidural electrical stimulation studies, single electrode sites and continuous tetanic stimulation have often been used. With this stimulation, the body is prone to declines in tolerance and locomotion coordination. In the present study, rat models of complete spinal cord injury were established by vertically cutting the spinal cord at the T8 level to eliminate disturbance from residual nerve fibers, and were then subjected to epidural electrical stimulation. The flexible extradural electrode had good anatomical topology and matched the shape of the spinal canal of the implanted segment. Simultaneously, the electrode stimulation site was able to be accurately applied to the L2-3 and S1 segments of the spinal cord. To evaluate the biocompatibility of the implanted epidural electrical stimulation electrodes, GFAP/Iba-1 double-labeled immunofluorescence staining was performed on the spinal cord below the electrodes at 7 days after the electrode implantation. Immunofluorescence results revealed no significant differences in the numbers or morphologies of microglia and astrocytes in the spinal cord after electrode implantation, and there was no activated Iba-1+ cell aggregation, indicating that the implant did not cause an inflammatory response in the spinal cord. Rat gait analysis showed that, at 3 days after surgery, gait became coordinated in rats with spinal cord injury under burst stimulation. The regained locomotion could clearly distinguish the support phase and the swing phase and dynamically adjust with the frequency of stimulus distribution. To evaluate the matching degree between the flexible epidural electrode (including three stimulation contacts), vertebral morphology, and the level of the epidural site of the stimulation electrode, micro-CT was used to scan the thoracolumbar vertebrae of rats before and after electrode implantation. Based on the experimental results of gait recovery using three-site stimulation electrodes at L2-3 and S1 combined with burst stimulation in a rat model of spinal cord injury, epidural electrical stimulation is a promising protocol that needs to be further explored. This study was approved by the Animal Ethics Committee of Chinese PLA General Hospital (approval No. 2019-X15-39) on April 19, 2019.

Influences of head/neck ratio and femoral antetorsion on the safe-zone of operative acetabular orientations in total hip arthroplasty.

OBJECTIVE: To study the influences of head/neck ratio and femoral antetorsion on the safe-zone of operative acetabular orientations, which meets the criteria for desired range of motion (ROM) for activities of daily living in total hip arthroplasty (THA). METHODS: A three-dimensional generic, parametric and kinematic simulation module of THA was developed to analyze the cup safe-zone and the optimum combination of cup and neck antetorsion. A ROM of flexion > or =120 degree internal rotation > or = 45 degree at 90 degree flexion, extension > or = 30 degree and external rotation > or =40 degree was defined as the criteria for desired ROM for activities of daily living. The cup safe-zone was defined as the area that fulfills all the criteria of desired ROM before the neck impinged on the liner of the cup. For a fixed stem-neck (CCD)-angle of 130 degree theoretical safe-zones fulfilling the desired ROM were investigated at different general head-neck ratios (GR=2, 2.17, 2.37, 2.61 and 2.92) and femoral anteversions (FA equal to 0 degree,10 degree,20 degree and 30 degree). RESULTS: Large GRs greatly increased the size of safe-zones and when the CCD-angle was 130 degree, a GR larger than 2.37 could further increase the size of safe-zones. There was a complex interplay between the orientation angles of the femoral and acetabular components. When the CCD-angle was 130 degree the optimum relationship between operative acetabular anteversion (OA) and femoral antetorsion (FA) could be estimated by the formula: OA equal to -0.80 multiply FA+47.06, and the minimum allowable operative acetabular inclination (OI(min)) would be more than 210.5 multiply GR(-2.255). CONCLUSIONS: Large GRs greatly increase the size of safe-zones and it is recommended that the GR be more than 2.37 so as to extend the acceptable range of error that surgeons cannot avoid completely during operation. As to the optimum operative acetabular inclination (OI), surgeons need to make a decision combining with other factors, including stress distribution, soft tissue and cup wear conditions, as well as patients'individual situations and demands. The data obtained from this study and the module of THA can be used to assist surgeons to choose and implant appropriate implants.

[Surgical treatment of compound fracture of the ankle].

OBJECTIVE: To report the clinical outcome of the treatment of compound ankle fractures by vacuum sealing drainage and spanning external fixator. METHODS: From April 2005 to April 2009, 19 cases of Gustilo type III compound ankle fractures were treated, with type IIIA in 10 cases, Type IIIB in 7 and Type IIIC in 2. All cases underwent emergency debridement, and had the fractures fixed with spanning external fixator following indirect reduction, the wound closed with vacuum sealing drainage and repaired through direct suture, split-thickness skin graft or flap transposition. RESULTS: In this series, following VSD of 5.0 to 18.0 d (mean 10.3 d), 2 cases had their wounds closed by direct suture, 12 by skin graft and 3 by flap transposition. The other 2 cases had repeated wound debridement and multiple use of VSD, and had their wounds repaired by flap transposition. All the 19 cases were followed up for 8 to 36 months with an average of 26 months. All the fractures united 3.0 to 10.0 (mean 3.8) months. At the final follow-up functional evaluation of the affected ankle joints was performed only to find excellent in 9 cases, good in 5, fair in 4 and poor in 1. CONCLUSION: Gustilo type III compound ankle fracture can effectively be treated with VSD and spanning external fixator.

A Hybrid Uniplanar Pedicle Screw System with a New Intermediate Screw for Minimally Invasive Spinal Fixation: A Finite Element Analysis.

PURPOSE: A hybrid pedicle screw system for minimally invasive spinal fixation was developed based on the uniplanar pedicle screw construct and a new intermediate screw. Its biomechanical performance was evaluated using finite element (FE) analysis. METHODS: A T12-L2 FE model was established to simulate the L1 vertebral compression fracture with Magerl classification A1.2. Six fixation models were developed to simulate the posterior pedicle screw fracture fixation, which were divided into two subgroups with different construct configurations: (1) six-monoaxial/uniplanar/polyaxial pedicle screw constructs and (2) four-monoaxial/uniplanar/polyaxial pedicle screw constructs with the new intermediate screw. After model validation, flexion, extension, lateral bending, and axial rotation with 7.5 Nm moments and preloading of 500 N vertical compression were applied to the FE models to compare the biomechanical performances of the six fixation models with maximum von Mises stress, range of motion, and maximum displacement of the vertebra. RESULTS: Under four loading scenarios, the maximum von Mises stresses were found to be at the roots of the upper or lower pedicle screws. In the cases of flexion, lateral bending, and axial rotation, the maximum von Mises stress of the uniplanar screw construct lay in between the monoaxial and polyaxial screw constructs in each subgroup. Considering lateral bending, the uniplanar screw construct enabled to lower the maximum von Mises stress than monoaxial and polyaxial pedicle screw constructs in each subgroup. Two subgroups showed comparable results of the maximum von Mises stress on the endplates, range of motion of T12-L1, and maximum displacement of T12 between the corresponding constructs with the new intermediate screw or not. CONCLUSIONS: The observations shown in this study verified that the hybrid uniplanar pedicle screw system exhibited comparable biomechanical performance as compared with other posterior short-segment constructs. The potential advantage of this new fixation system may provide researchers and clinical practitioners an alternative for minimally invasive spinal fixation with vertebral augmentation.

Evolution and Current Applications of Robot-Assisted Fracture Reduction: A Comprehensive Review.

Robots in orthopedic surgery have been developed rapidly for decades and bring significant benefits to the patients and healthcare providers. However, robotics in fracture reduction remains at the infant stage. As essential components of the current robotic system, external fixators were used in fracture reduction, including the unilateral and Ilizarov-like ring fixators. With emerging of the industrial robots and mechanical arms, their sterilized variants were developed as the serial robots, including the traction device and robotic arm, for fracture reduction. Besides, parallel robots (e.g., Gough-Stewart platform) were devised for lower extremity traction and fracture reduction. After combining the advantages of the serial and parallel mechanisms, hybrid robots can fulfill specific clinical requirements (e.g., the joint fracture, including multiple major fragments). Furthermore, with the aid of intra-operative navigation systems, fracture reduction can be performed under real-time guidance. The paper presents a comprehensive overview of the advancement of the robots in fracture reduction and evaluates research challenges and future perspectives, including ergonomic and economic issues, operation time, artificial realities and intelligence, and telesurgery.