Effect of different acclimation methods on the performance of microbial fuel cells using phenol as substrate.

Single-chamber microbial fuel cells (MFCs) with air-cathode were constructed. MFCs were fed different feedstocks during their inoculation, their role on phenol degradation and MFC performance were investigated. The results showed that the MFC inoculated using glucose exhibited the highest power density (31.3 mW m(-2)) when phenol was used as the sole substrate for MFC. The corresponding biodegradation kinetic constant was obtained at 0.035 h(-1), at an initial phenol concentration of 600 mg L(-1). Moreover, the phenol degradation rates in this MFC with closed circuit were 9.8-16.5% higher than those in MFC with opened circuit. The cyclic voltammograms revealed a different electrochemical activity of the anode biofilms in the MFC, and this led to differences in performance of the MFCs with phenol as sole substrate. These results demonstrated that phenol degradation and power production are affected by current generation and type of acclimation.

Study on a novel omnidirectional ultrasonic cavitation removal system for Microcystis aeruginosa.

Microcystis aeruginosa, as a typical alga, produces microcystin with strong liver toxicity, seriously endangering the liver health of human and animals. Inhibiting the bloom of the Microcystis aeruginosa in lakes becomes a significant and meaningful work. Ultrasonic cavitation is currently considered to be the most environmentally friendly and effective method for the removal of Microcystis aeruginosa. However, the commercialized ultrasonic algae removal systems require multi-Langevin transducers to achieve omnidirectional ultrasonic irradiation due to the single irradiation direction of the Langevin transducer, resulting in the complex design and high energy consumption. To achieve a low-cost, simple structure, and high-efficiency algae removal system, a novel omnidirectional ultrasonic cavitation removal system for Microcystis aeruginosa is proposed. The proposed system is major composed of a novel omnidirectional ultrasonic transducer, which generates the omnidirectional ultrasonic irradiation by its shaking-head motion coupled by two orthogonal bending vibration modes. Modal simulation, sound field simulation, and cavitation bubble radius simulation are first carried out to optimize the geometric sizes of the proposed transducer and verify the correctness of the omnidirectional ultrasonic irradiation principle. Then the vibration characteristics of the transducer prototype are measured by vibration tests and impedance tests. Finally, the feasibility and effectiveness of the proposed omnidirectional ultrasonic removal system for Microcystis aeruginosa are evaluated through the algae removal experiments. The experimental results exhibit that the algal cells damaged by ultrasonic irradiation from the proposed system do not have the ability to self-repair. In addition, the algal removal rates reached 55.41% and 72.97% after 30 min of ultrasonic treatment when the corresponding ultrasonic densities are 0.014 W/mL and 0.021 W/mL, respectively. The proposed omnidirectional ultrasonic algae removal system significantly simplifies the configuration and reduces energy consumption, presenting the potential promise of algae removal and environmental protection.

Electrophoretic deposition of multi-walled carbon nanotube on a stainless steel electrode for use in sediment microbial fuel cells.

Sediment microbial fuel cells (SMFCs) could be used as power sources and one type of new technology for the removal of organic matters in sediments. In order to improve electrode materials and enhance their effect on the performance, we deposited multi-walled carbon nanotube (MWNT) on stainless steel net (SSN). Electrophoretic deposition technique as a method with low cost, process simplicity, and thickness control was used for this electrode modification and produced this novel SSN-MWNT electrode. The performances of SMFCs with SSN-MWNT as electrode were investigated. The results showed that the maximum power density of SMFC with SSN-MWNT cathode was 31.6 mW m(-2), which was 3.2 times that of SMFC with an uncoated stainless steel cathode. However, no significant increase in the maximum power density of SMFC with SSN-MWNT anode was detected. Further electrochemical analysis showed that when SSN-MWNT was used as the cathode, the cathodic electrochemical activity and oxygen reduction rate were significantly improved. This study demonstrates that the electrophoretic deposition of carbon nanotubes on conductive substrate can be applied for improving the performance of SMFC.

Construction and operation of microbial fuel cell with Chlorella vulgaris biocathode for electricity generation.

In this study, a modified microbial fuel cell (MFC) with a tubular photobioreactor (PHB) configuration as a cathode compartment was constructed by introducing Chlorella vulgaris to the cathode chamber used to generate oxygen in situ. Two types of cathode materials and light/dark cycles were used to test the effect on MFC with algae biocathode. Results showed that the use of algae is an effective approach because these organisms can act as efficient in situ oxygenators, thereby facilitating the cathodic reaction. Dissolved oxygen and voltage output displayed a clear light positive response and were drastically enhanced compared with the abiotic cathode. In particular, carbon paper-coated Pt used as a cathode electrode increased voltage output at a higher extent than carbon felt used as an electrode. The maximum power density of 24.4 mW/m(2) was obtained from the MFC with algae biocathode which utilized the carbon paper-coated Pt as the cathode electrode under intermittent illumination. This density was 2.8 times higher than that of the abiotic cathode. Continuous illumination shortened the algal lifetime. These results demonstrated that intermittent illumination and cathode material-coated catalyst are beneficial to a more efficient and prolonged operation of MFC with C. vulgaris biocathode.

Construction and operation of microbial fuel cell with Chlorella vulgaris biocathode for electricity generation.

In this study, a modified microbial fuel cell (MFC) with a tubular photobioreactor (PHB) configuration as a cathode compartment was constructed by introducing Chlorella vulgaris to the cathode chamber used to generate oxygen in situ. Two types of cathode materials and light/dark cycles were used to test the effect on MFC with algae biocathode. Results showed that the use of algae is an effective approach because these organisms can act as efficient in situ oxygenators, thereby facilitating the cathodic reaction. Dissolved oxygen and voltage output displayed a clear light positive response and were drastically enhanced compared with the abiotic cathode. In particular, carbon paper-coated Pt used as a cathode electrode increased voltage output at a higher extent than carbon felt used as an electrode. The maximum power density of 24.4 mW/m2 was obtained from the MFC with algae biocathode which utilized the carbon paper-coated Pt as the cathode electrode under intermittent illumination. This density was 2.8 times higher than that of the abiotic cathode. Continuous illumination shortened the algal lifetime. These results demonstrated that intermittent illumination and cathode material-coated catalyst are beneficial to a more efficient and prolonged operation of MFC with C. vulgaris biocathode.