Flexible Hollow Core Fiber Photoacoustic Gas Sensor Based on Embedded Acoustic Resonant Structure.

In this paper, we demonstrate a flexible leaky hollow core fiber (LHCF) photoacoustic (PA) gas sensor based on an embedded acoustic resonant structure. The sensor employs a part of a gas conduit as the buffer chamber to construct an equivalent T-type half-open PA cell. The LHCF is installed inside of the gas conduit and the LHCF is hence replaceable. Also, the flexibility of the LHCF and the gas conduit make the gas sensor flexible to reduce spatial size. The inner diameter and length of the LHCF are 1.6 mm and 70 mm, respectively. The inner diameter and length of the gas conduit are 4 mm and 210 mm, respectively. The total gas volume of the sensor is only ∼2.6 mL. Trace acetylene (C2H2) is selected as the target gas to evaluate the performance of the PA gas sensor. A near-infrared distributed feedback (DFB) laser is utilized to generate the PA signal, and an electrical micro-electro-mechanical system (MEMS) microphone is employed to extract the PA signal. The experimental results show that the minimum detection limit (MDL) can be as low as 21.1 ppb when the lock-in integration time is 200 s. And the normalized noise equivalent absorption coefficient (NNEA) is calculated to be 5.7 × 10-9·W/cm-1·Hz-1/2.

Long-range surface plasmon resonance-based hollow fiber temperature sensor with ultrahigh sensitivity and tunable detection range.

A dielectric/Ag-coated hollow fiber (HF) temperature sensor based on long-range surface plasmon resonance (LRSPR) is proposed and experimentally demonstrated. The structural parameters, including the dielectric material and layer thicknesses, are optimized through comprehensive theoretical analysis to achieve the best performance. By filling it with a high refractive index (RI) thermosensitive liquid, the GK570/Ag-coated HF temperature sensor with optimal structural parameters is fabricated. Due to the high sensitivity of the LRSPR sensor and the optimized design, the fabricated sensor achieves a temperature sensitivity of 3.6∼20.5 nm/°C, which is almost the highest among the optical fiber temperature sensors based on surface plasmon resonance reported experimentally. Moreover, the detection range of the proposed sensor can be easily tuned up to 170°C by varying the RI of the filled thermosensitive liquid, and the sensor performance remains stable. Considering that most temperature sensors using polydimethylsiloxane have a fixed detection range, this is an outstanding advantage that could expand the application field of the optical fiber temperature sensor.

Surface-Enhanced Raman Scattering in Silver-Coated Suspended-Core Fiber.

In this paper, the silver-coated large-core suspended-core fiber (LSCF) probe was fabricated by the dynamic chemical liquid phase deposition method for surface-enhanced Raman scattering (SERS) sensing. The 4-mercaptophenylboronic acid (4-MPBA) monolayer was assembled in the LSCF as the recognition monolayer. Taking advantage of the appropriate core size of the LSCF, a custom-made Y-type optical fiber patch cable was utilized to connect the semiconductor laser, Raman spectrometer, and the proposed fiber SERS probe. The SERS signal is propagated in the silver-coated air channels, which can effectively reduce the Raman and fluorescence background of the silica core. Experiments were performed to measure the Raman scattering spectra of the 4-MPBA in the silver-coated LSCF in a non-enhanced and enhanced case. The experiment results showed that the Raman signal strength was enhanced more than 6 times by the surface plasmon resonance compared with the non-enhanced case. The proposed LSCF for SERS sensing technology provides huge research value for the fiber SERS probes in biomedicine and environmental science. The combination of SERS and microstructured optical fibers offers a potential approach for SERS detection.

[Advances in traditional Chinese medicine treatment of non-alcoholic fatty liver disease via farnesoid X receptor].

Non-alcoholic fatty liver disease(NAFLD) is a chronic metabolic condition with rapidly increasing incidence, becoming a public health issue of worldwide concern. Studies have shown that farnesoid X receptor(FXR)-based modulation of downstream targets can improve liver function and metabolic status in the patients with NAFLD and may be a potential drug target for treating this di-sease. Great progress has been achieved in the development of drugs targeting FXR for the treatment of NAFLD. A number of studies have explored the traditional Chinese medicine and their active ingredients for the treatment of NAFLD via FXR considering the high safety and efficacy and mild side effects. This paper systematically describes the mechanism of traditional Chinese medicines in the treatment of NAFLD via FXR and the downstream targets, aiming to provide precise targets for the drug development and clinical treatment of NAFLD.

Surface plasmon resonance temperature sensor with tunable detection range based on a silver-coated multi-hole optical fiber.

A novel surface plasmon resonance (SPR) temperature sensor based on a silver-coated multi-hole optical fiber (SMHOF) is presented. The central and surrounding air holes of the SMHOF are filled with two kinds of thermosensitive liquid with high and low refractive index (RI), respectively. Two separated resonance dips, which are related to the high and low RI filled liquid respectively, are observed at different wavelength in the transmission spectrum. Advantageously, the two dips move towards opposite direction with the temperature variation. The interval between the two SPR dips is measured under different environmental temperature and exhibits a good linearity. The proposed sensor with different detection range is fabricated by changing the RIs of the filled thermosensitive liquids. The temperature sensitivity of 7.72 nm/°C and -7.81 nm/°C is obtained in the range of 20-60 °C and -20-20 °C, respectively. Owing to the high temperature sensitivity and tunable detection range, the proposed sensor is expected to find potential applications in biomedicine, health care and environmental monitoring.

Dielectric layer thickness insensitive EVA/Ag-coated hollow fiber temperature sensor based on long-range surface plasmon resonance.

A novel hollow fiber temperature sensor (HFTS) based on long-range surface plasmon resonance is presented. The HFTS consists of a dielectric/Ag-coated hollow fiber filled with the thermosensitive liquid and two multimode fibers connected at both ends. By measuring the transmission spectra under different temperatures, the performances, including sensitivity and figure of merit (FOM) of the sensors with different structural parameters, such as thermosensitive liquid property, ethylene-vinyl acetate (EVA) and silver layer thicknesses, were investigated experimentally. The results shows that the sensitivity of the optimized HFTS is 1.60nm/°C to 5.21nm/°C in the range from 20°C to 60°C, and the FOM is up to 0.0453°C-1. Both performances are higher than most reported optical fiber temperature sensors based on surface plasmon resonance. Moreover, the performance of the HFTS is not sensitive to the dielectric layer thickness, which greatly reduces the difficulty of fabrication.

Fiber polarizer based on selectively silver-coated large-core suspended-core fiber.

A tunable fiber polarizer based on the selectively silver-coated large-core suspended-core fiber (LSCF) was proposed. A thin silver layer was coated on the inner surface of two opposite air holes of the LSCF by the chemical liquid-phase deposition method. The $y$-polarized light (parallel to the two silver-coated air holes) will excite surface plasmon resonance and experience large transmission loss, while the $x$-polarized light does not, resulting in a fiber polarizer. By varying the liquid filled in the microchannels of the LSCF, the operating wavelength can be tuned in the visible and near infrared region along with the surface plasmon resonance wavelength. The dependence of the polarization characteristics on the fiber length was experimentally investigated. The maximum polarization extinction ratio (PER) of 20.1 dB, 19.6 dB, and 18.3 dB and insertion loss (IL) of 2.24 dB, 2.56 dB, and 2.08 dB are achieved with the optimal fiber length of 16 cm at the operating wavelengths of 565.4 nm, 626.7 nm, and 739.7 nm, respectively. Compared with the multimode fiber-based polarizers reported previously, the proposed selectively silver-coated LSCF polarizer exhibits higher PER and lower IL.

Long-range surface plasmon resonance sensor based on the GK570/Ag coated hollow fiber with an asymmetric layer structure.

A long-range surface plasmon resonance (LRSPR) sensor based on GK570/Silver coated hollow fiber (HF) with an asymmetric layer structure is proposed. A set of proposed sensors with different layer thicknesses were fabricated by the liquid phase coating method. Both theoretical and experimental analyses were carried out to evaluate the performances of the fabricated sensors, such as sensitivity, figure of merit (FOM) and detection range. The theoretical results based on the ray modal agreed well with the experimental results. The highest experimentally obtained sensitivity and FOM were over 12500 nm/RIU and 150 RIU-1, respectively. The FOM was approximately ten times that of the HF SPR sensor. Moreover, compared to the HF LRSPR sensor with a symmetric layer structure, the proposed sensor has a much larger sensitivity and an approximately double FOM without sacrificing other advantages of the HF LRSPR sensor.

Fiber optic surface plasmon resonance sensor based on a silver-coated large-core suspended-core fiber.

A fiber optic surface plasmon resonance (SPR) sensor based on a silver-coated large-core suspended-core fiber was proposed. A dynamic chemical liquid phase deposition method was adopted to fabricate a set of proposed sensors with different silver layer thicknesses. A stable fully spiced all-fiber sensing system was established to evaluate the performance of the fabricated sensors. The results show that the proposed sensor with a thicker silver layer exhibits higher sensitivity and figure of merit. The performance of the proposed sensor is comparable to those of the conventional solid-core fiber and hollow fiber SPR sensors and much higher than that of the metal nanoparticle functionalized suspended-core fiber sensors.

Improving the performance of hollow fiber surface plasssmon resonance sensor with one dimensional photonic crystal structure.

A high performance hollow fiber (HF) surface plasmon resonance (SPR) sensor utilizing one-dimensional photonic crystal (1DPC) is proposed. The performance of the designed sensor is analyzed theoretically with respect to the center wavelength and the bilayer period. Because the light transmitted in the sensor mostly have large incident angles, the center wavelength of the 1DPC should shift to longer wavelength to ensure the band gap covers the spectrum range of the incident light. The sensor exhibits better performance when the detection spectral range is located in the band gap of 1DPC for incident angle larger than 80°. Compared to conventional HF SPR sensor, the figure of merit (FOM) of the proposed sensor is three to four times higher while the sensitivity is comparable. Moreover, within the limited spectrum range of 400 to 800nm, the proposed sensor have much wider refractive index (RI) detection range and can detect sensed medium with low RI very close to the supporting tube.

An Optical Fiber Refractive Index Sensor Based on the Hybrid Mode of Tamm and Surface Plasmon Polaritons.

A novel high performance optical fiber refractive index (RI) sensor based on the hybrid transverse magnetic (TM) mode of Tamm plasmon polariton (TPP) and surface plasmon polariton (SPP) is proposed. The structure of the sensor is a multi-mode optical fiber with a one dimensional photonic crystal (1 DPC)/metal multi-films outer coated on its fiber core. A simulation study of the proposed sensor is carried out with the geometrical optical model to investigate the performance of the designed sensor with respect to the center wavelength, bilayer period and the thickness of silver layer. Because the lights transmitted in the fiber sensor have much larger incident angles than those in the prism based sensors, the center wavelength of the 1 DPC should shift to longer wavelength. When the coupling between TM-TPP and SPP is stronger, the sensor exhibits better performance because the electromagnetic field of the TPP-SPP hybrid mode is enhanced more in the analyte. Compared to most conventional fiber surface plasmon resonance sensors, the figure of merit of the proposed sensor is much higher while the sensitivity is comparable. The idea of utilizing TPP-SPP hybrid mode for RI sensing in the solid-core optical fiber structure presented in this paper could contribute to the study of the fiber RI sensor based on TPP.

Hollow fiber sensor based on metal-cladding waveguide with extended detection range.

A new hollow fiber sensor based on metal-cladding waveguide configuration for the detection of the refractive index of liquid is proposed and demonstrated. Due to the existence of both surface and guided modes in the metal-insulator-metal waveguide, the proposed sensor can detect liquid with refractive index either higher or lower than the insulator layer, which significantly extends the detection range. The characteristics of metal-cladding waveguide is analyzed and presented, while the performance of the sensor is numerically calculated and evaluated. The results evince that, the designed fiber sensor can effectively detect both high and low refractive index liquid by respectively exciting surface mode and guided mode.

Diallyl trisulfide suppresses tumor growth through the attenuation of Nrf2/Akt and activation of p38/JNK and potentiates cisplatin efficacy in gastric cancer treatment.

Diallyl trisulfide (DATS), a garlic organosulfide, has shown excellent chemopreventive potential. Cisplatin (DDP) is widely used to treat solid malignant tumors, but causing serious side effects. In the current study, we attempted to elucidate the chemopreventive mechanisms of DATS in human gastric cancer BGC-823 cells in vitro, and to investigate whether DATS could enhance the anti-tumor efficacy of DDP and improve quality of life in BGC-823 xenograft mice in vivo. Treatment with DATS (25-400 µmol/L) dose-dependently inhibited the viability of BGC-823 cells in vitro with an IC50 of 115.2±4.3 µmol/L after 24 h drug exposure. DATS (50-200 µmol/L) induced cell cycle arrest at G2/M phase in BGC-823 cells, which correlated with significant accumulation of cyclin A2 and B1. DATS also induced BGC-823 cell apoptosis, which was accompanied by the modulation of Bcl-2 family members and caspase cascade activation. In BGC-823 xenograft mice, administration of DATS (20-40 mg·kg-1·d-1, ip) dose-dependently inhibited tumor growth and markedly reduced the number of Ki-67 positive cells in tumors. Interestingly, combined administration of DATS (30 mg·kg-1·d-1, ip) with DDP (5 mg/kg, every 5 d, ip) exhibited enhanced anti-tumor activity with fewer side effects. We showed that treatment of BGC-823 cells with DATS in vitro and in vivo significantly activated kinases such as p38 and JNK/MAPK and attenuated the Nrf2/Akt pathway. This study provides evidence that DATS exerts anticancer effects and enhances the antitumor efficacy of DDP, making it a novel candidate for adjuvant therapy for gastric cancer.

Optical fiber sensor based on Bloch surface wave in photonic crystals.

A new optical fiber sensor based on Bloch surface wave was theoretically proposed. An omnidirectional one-dimensional photonic crystal was designed as the multilayer coated on the outer surface of the optical fiber. Taking advantages of the omnidirectional reflection band, there is only surface mode resonance in the transmission spectrum, while guided mode resonance is avoided. The performance of the designed fiber sensor was analyzed theoretically with a ray transmission model. The presented sensor has comparable sensitivity but much higher figure of merit than other fiber sensors. The resolution can reach about 10-6 RIU or even higher.

Enhancing photonic spin Hall effect via long-range surface plasmon resonance.

We presented the significant enhancement of the photonic spin Hall effect by taking advantage of long-range surface plasmon resonance (LRSPR). The influence of the thicknesses of metal and dielectric layers in the insulator-metal-insulator structure which supports LRSPR was investigated. Under the optimal parameter setup, the largest transverse separation with a 632.8 nm incident Gaussian beam reaches 7.85 µm, which is much larger than previous reported values.

Long-range surface plasmon resonance sensor based on dielectric/silver coated hollow fiber with enhanced figure of merit.

A long-range surface plasmon resonance (LRSPR) sensor based on dielectric/silver-coated hollow fiber (HF) is proposed. It can detect the refractive index (RI) of sensed liquid filled in the hollow core of the sensor. A HF LRSPR sensor with 90-nm-thick silver layer and 260-nm-thick OC300 layer is fabricated. Experiments are taken to evaluate the performance of the sensor by measuring the transmission spectra. Theoretical analysis based on a ray model is also taken, and the results agree well with the experimental results. The proposed sensor has similar sensitivity but much smaller SPR dip width than the silver-coated HF SPR sensor. Thus figure of merit of the sensor is enhanced approximately five times. The stability of the sensor is also improved because the dielectric layer acts as a protection layer for the damageable silver layer.

Surface Plasmon Resonance Sensor Based on Ethylene Tetra-Fluoro-Ethylene Hollow Fiber.

A new kind of hollow fiber surface plasmon resonance sensor (HF-SPRS) based on the silver-coated ethylene tetra-fluoro-ethylene (ETFE) hollow fiber (HF) is presented. The ETFE HF-SPRS is fabricated, and its performance is investigated experimentally by measuring the transmission spectra of the sensor when filled by liquid sensed media with different refractive indices (RIs). Theoretical analysis based on the ray transmission model is also taken to evaluate the sensor. Because the RI of ETFE is much lower than that of fused silica (FSG), the ETFE HF-SPRS can extend the lower limit of the detection range of the early reported FSG HF-SPRS from 1.5 to 1.42 approximately. This could greatly enhance the application potential of HF-SPRS. Moreover, the joint use of both ETFE and FSG HF-SPRSs can cover a wide detection range from 1.42 to 1.69 approximately with high sensitivities larger than 1000 nm/RIU.

Silver-coated hollow fiber surface plasmon resonance sensor for glucose detection with enhanced limit of detection.

A fiber-optic surface plasmon resonance (SPR) biosensor based on a silver-coated hollow fiber (HF) structure for glucose detection is presented. The sensor surface was immobilized with 4-mercaptophenylboronic acid (PMBA) acting as a glucose recognition monolayer. Then, gold nanoparticles (AuNPs) modified with 2-aminoethanethiol (2-AET) and PMBA were introduced onto the sensor surface after glucose was captured to enhance the wavelength shift of the SPR phenomenon excited by the light transmitted in the wall of the HF sensor. Instead of the conventional one-step sensitization pretreatment commonly used in the deposition process of silver films for fiber-optic SPR sensors, a sensitization-activation two-step activation method was adopted in the fabrication of the proposed sensor. Experiments for glucose detection were performed on the fabricated sensors in the concentration range of 1 nM-1 mM. Results showed that the sensor fabricated by the two-step activation method has a much larger shift of resonance wavelength than the sensor fabricated using the one-step sensitization method. The resonance wavelength shift was found to be linear to the logarithm of the concentration in the range of 1 nM-1 mM. The sensor achieved a limit of detection (LOD) of as low as 1 nM, which is at least an order of magnitude lower than that of other fiber-optic sensors for glucose detection reported previously. The presented HF glucose sensor has the potential for biosensing applications and provides a large reference value in the study of optical fiber SPR sensors for biosensing.

Hollow fiber surface plasmon resonance sensor for the detection of liquid with high refractive index.

A new kind of surface plasmon resonance (SPR) sensor based on silver-coated hollow fiber (HF) structure for the detection of liquids with high refractive index (RI) is presented. Liquid sensed medium with high RI is filled in the hollow core of the HF and its RI can be detected by measuring the transmission spectra of the HF SPR sensor. The designed sensors with different silver thicknesses are fabricated and the transmission spectra for filled liquids with different RI are measured to investigate the performances of the sensors. Theoretical analysis is also carried out to evaluate the performance. The simulation results agree well with the experimental results. Factors that might affect sensitivity and detection accuracy of the sensor are discussed. The highest sensitivity achieved is 6,607 nm/RIU, which is comparable to the sensitivities of the other reported fiber SPR sensors.

Determination of atropisomeric configurations of macrocyclic bisbibenzyls by HPLC-CD/UV and quantum chemical calculations.

Isoriccardin C (1) and riccardin D (2), isolated from the liverwort Reboulia hemisphaerica, were first characterized to be a mixture of two enantiomeric atropisomers by online chiral high-performance liquid chromatography-circular dichroism (HPLC-CD) analysis. Exemplarily for bisbibenzyls of the diarylether-biphenyl type, the absolute atropisomeric configurations of compunds 1 and 2 were determined by the analysis of their CD data coupled with quantum chemical CD calculations.