The motion of micro-swimmers over a cavity in a micro-channel.

This article combines the lattice Boltzmann method (LBM) with the squirmer model to investigate the motion of micro-swimmers in a channel-cavity system. The study analyses various influential factors, including the value of the squirmer-type factor (ß), the swimming Reynolds number (Rep), the size of the cavity, initial position and particle size on the movement of micro-swimmers within the channel-cavity system. We simultaneously studied three types of squirmer models, Puller (ß > 0), Pusher (ß < 0), and Neutral (ß = 0) swimmers. The findings reveal that the motion of micro-swimmers is determined by the value of ß and Rep, which can be classified into six distinct motion modes. For Puller and Pusher, when the ß value is constant, an increase in Rep will lead to transition in the motion mode. Moreover, the appropriate depth of cavity within the channel-cavity system plays a crucial role in capturing and separating Neutral swimmers. This study, for the first time, explores the effect of complex channel-cavity systems on the behaviour of micro-swimmers and highlights their separation and capture ability. These findings offer novel insights for the design and enhancement of micro-channel structures in achieving efficient separation and capture of micro-swimmers.

Numerical Analysis of Droplet Impact on the Convex Surface with Liquid Film.

Droplet impact on film is a common natural appearance in industrial production. The numerical simulation method is used to simulate the evolution process of droplet impact on different convex surfaces with liquid film to study the influence of various surface structures on the impact of droplets on the film. The mechanism of droplet impact on irregular wall is also explored. The effect of the height and width of the convex on the evolution of the interphase interface and the characteristic parameters of the crown and cavity are discussed. Based on the results, the convex has a great effect on the change form of droplets after impacting the liquid film. A region of high pressure will appear above the convex, and vortices will form around it. In terms of the characteristics of the crown, the growth rate of the crown height increases with the height of the convex. The spreading diameter of the crown increases with the height of the convex. The effect of convex width on the crown is less than that of convex height. The convex has a great influence on the evolution of the cavity, and the convex of different scales will affect the development shape of the cavity. The present finding provides theoretical guidance for the application of droplets impinging on liquid film.

Effect of Shaft Diameter on the Hydrodynamic Torque of Butterfly Valve Disk.

In this study, computational fluid dynamics (cfd) software and detached eddy simulation turbulence model were used to simulate butterfly valves with different designs. The effects of shaft diameters on the value and the fluctuation of valve disk torque were studied, and the physical reason was discussed. The simulation results were verified by comparing with the experimental data. The findings revealed that with the closing of the valve, the hydraulic torque of the valve disk first increases and then decreases. Meanwhile, the torque decreases gradually with the increase of the shaft diameter. The variation of torque is caused by the change of pressure on both sides of the valve disk. The result also indicates that the fluctuation of torque is induced by the flow separation phenomenon occurs on the valve disk. The fluctuation is significant for the valve opening from 20% to 60%. The strength of the torque fluctuation is greater for the smaller shaft diameter. This study provides a theoretical basis for the design and optimization of butterfly valves.

Statistics of Heat Transfer in Two-Dimensional Turbulent Rayleigh-Bénard Convection at Various Prandtl Number.

Statistics of heat transfer in two-dimensional (2D) turbulent Rayleigh-Bénard (RB) convection for Pr=6,20,100 and 106 are investigated using the lattice Boltzmann method (LBM). Our results reveal that the large scale circulation is gradually broken up into small scale structures plumes with the increase of Pr, the large scale circulation disappears with increasing Pr, and a great deal of smaller thermal plumes vertically rise and fall from the bottom to top walls. It is further indicated that vertical motion of various plumes gradually plays main role with increasing Pr. In addition, our analysis also shows that the thermal dissipation is distributed mainly in the position of high temperature gradient, the thermal dissipation rate εθ already increasingly plays a dominant position in the thermal transport, εu can have no effect with increase of Pr. The kinematic viscosity dissipation rate and the thermal dissipation rate gradually decrease with increasing Pr. The energy spectrum significantly decreases with the increase of Pr. A scope of linear scaling arises in the second order velocity structure functions, the temperature structure function and mixed structure function(temperature-velocity). The value of linear scaling and the 2nd-order velocity decrease with increasing Pr, which is qualitatively consistent with the theoretical predictions.

A theoretical model for predicting the startup performance of pumps as turbines.

Using the unsteady Bernoulli equation for the piping system and the angular momentum equation for the rotor, derives here a theoretical model to predict the startup performance of a pump as turbine (PAT). This model is effective for predicting the instantaneous evolution characteristics of the main performance parameters of PAT during startup, and these changings are initially faster and then slowly as a whole. The effect of the rotor moment of inertia and the final stabilized rotational speed of PAT on evolution characteristics of parameters is opposite. The rotational speed, head, hydraulic power, and conversion efficiency show a upward rising trend with the startup time, whereas the flow rate and hydraulic head loss display a downward trend.

A self-cleaning micro-fluidic chip biospired by the filtering system of manta rays.

Size-based particle filtration has become indispensable in numerous biomedical and environmental applications. In this study, bioinspired by the filter-feeding mechanism (lobe filtration) of manta rays, we designed a U-shaped biomimetic gill rake filter that combined lobe filtration and Dean flow to filter monodisperse suspensions, bi-disperse suspensions and yeast cells. Compared with other equipment using the inertial focusing technology, our equipment can perform high-throughput (up to 8 mL min-1) and high-efficiency filtration of particles (maximum filtration efficiencies of 96.08% and 97.14% for 10 and 15 µm monodisperse suspensions at the optimum flow rate of 6 mL min-1). The complex velocity field of the micro-fluidic flow within the filter is numerically simulated, and in combination with experiments, a threshold for the flow rate is identified. When the inlet flow rate exceeds the threshold value, the efficiency of particle filtration is increased rapidly. Afterwards, by analysing the filtration mechanism, we develop three novel filtration processes. The equilibrium positions of the particles and yeast cells in the main channel are close to the outer wall at high flow rate, which diminishes the likelihood of particles and yeast cells entering the side channel. This configuration establishes a self-cleaning mechanism, ensuring prolonged and efficient operation of the filter with high-throughput processing. Furthermore, the influence of the filter lobe angle and channel width on the filtration efficiency and outlet flow rate ratio are explored, and an optimisation plan is prepared.

Investigations on cavitation flow and vorticity transport in a jet pump cavitation reactor with variable area ratios.

Hydrodynamic cavitation (HC) has emerged as a promising technology for water disinfection. Interestingly, when subjected to specific cavitation pressures, jet pump cavitation reactors (JPCRs) exhibit effective water treatment capabilities. This study investigated the cavitation flow and vorticty transport in a JPCR with various area ratios by utilizing computational fluid dynamics. The results reveal that cavitation is more likely to occur within the JPCR as the area ratio becomes smaller. While as the area ratio decreases, the limit flow ratio also decreases, leading to a reduced operational range for the JPCR. During the cavitation inception stage, only a few bubbles with limited travel distances are generated at the throat inlet. A stable cavitation layer developed between the throat and downstream wall during the limited cavitation stage. In this phase, the primary flow carried the bubbles towards the outlet. In addition, it was found that the vortex stretching, compression expansion, and baroclinic torque terms primarily influence the vorticity transport equation in this context. This work may provide a reference value to the design of JPCRs for water treatment.

Numerical calculation of forward and reverse flow in Tesla valves with different longitudinal width-to-narrow ratios.

To study the effect of the width-to-narrow ratio on the forward and reverse flow characteristics of the Tesla valve, five different models of the Tesla valve with different width-to-narrow ratios are established in this paper. The numerical calculations of forward and reverse flow under different working conditions are carried out by the CFD method in the laminar flow regime, and the reliability of the numerical calculation method is verified by comparing it with the experimental results. The results show that: in forward flow, the main flow-through channel is not related to the width-to-narrow ratio, the flow rate of the straight channel increases with the increase of the width-to-narrow ratio, and the static pressure in the diversion section is in the shape of "∞"; while in reverse flow, the main flow-through channel is weakly related to the width-to-narrow ratio, the flow rate of the arc channel is not increased with the increase of the width-to-narrow ratio, and the static pressure in the diversion section is in the shape of "bench". As the width-to-narrow ratio decreases, the pressure drop during forward and reverse flow becomes more significant.

The acceleration effect of pump as turbine system during starting period.

In order to reveal the influence of starting acceleration on starting process of a pump as turbine system, this paper carries out a numerical calculation of the three-dimensional viscous unsteady flow of pump as turbine circulating piping system under three starting acceleration conditions, and obtains the external and internal flow characteristics of each overflow component during the starting process, and also analyzes the energy loss of each component in the piping system in depth with the help of entropy production method and Q criterion method. The results show that during system start-up, the flow rate and outlet static pressure curves of the pump as turbine are hysteresis relative to the rotational speed, the head curve is similar to a linear rise during slow and medium speed start-up, while it shows a parabolic rise during rapid start-up, the entropy production and vorticity in the impeller domain of the pump as turbine are mainly distributed between the blades, and the distribution decreases during start-up. In addition, the pump similarity law does not apply to the performance prediction during the transient start of the pump as turbine.

Optimal design of impeller for self-priming pump based on orthogonal method.

In order to improve the efficiency of the self-priming pump in the outdoor emergency rescue mobile pump truck, this paper took the key energy conversion component-impeller as the target and used the orthogonal experimental design method to optimize its hydraulic performance. Firstly the numerical calculations were compared with the experimental results to confirm the reliability of the calculation method. Then, L9 (34) orthogonal design was applied to investigate the influence of the impeller diameter, the blade outlet width, the blade wrap angle and the number of blades on the hydraulic performance of the self-priming pump. Through range analysis, the order of influence of each influencing factor on the head and efficiency of the self-priming pump was determined, and finally obtained the optimal parameter combination scheme. The results show that the optimized self-priming pump exceeds the head of the prototype pump at all flow conditions, and the efficiency curve at high flow conditions is significantly improved and has a wide high efficiency zone.

Simulation of Slag Droplet Entrainment by Volume of Fluid and Lagrangian Particle Tracking Coupled Modeling.

The slag droplet entrainment is a common phenomenon in steel refining processes, which may lead to inclusions and defects. In the multiphase flow system, the distinct interface and tiny blobs possess a wide range of spatial and temporal scales and make it hard to be simulated. In numerical methods, the volume of fluid (VOF) approach is appropriate for capturing the interface, but for the unresolvable tiny blobs, the Lagrangian particle tracking (LPT) is preferable. This work newly implements a bidirectional VOF-LPT transformation algorithm for developing a multiscale solver in OpenFOAM to simulate the slag droplet entrainment. The interIsoFoam solver is selected as the main solver to resolve the interface, and the resolution is improved with using the geometric reconstruction and the adaptive mesh refinement (AMR). For capturing tiny droplets, a connected component labeling (CCL) method is adopted for detecting discrete droplets in the VOF field, and then the VOF-to-LPT transition takes place for saving computational costs. Conversely, the LPT-to-VOF transformation for droplets touching the interface is also incorporated to achieve the bidirectional transition. The solver is first validated by a simple case, indicating that the two-way transition algorithm and the Eulerian-Lagrangian momentum coupling are accurate. Then the solver is applied to simulate the slag layer behavior for revealing the mechanisms of slag droplet formation and entrainment. Two main mechanisms of slag droplet formation are identified, and it is found that fewer discrete droplets are generated when the surface tension increases.

Investigation of cavitation noise using Eulerian-Lagrangian multiscale modeling.

We have employed the large eddy simulation (LES) approach to investigate the cavitation noise characteristics of an unsteady cavitating flow around a NACA66 (National Advisory Committee for Aeronautics) hydrofoil by employing an Eulerian-Lagrangian based multiscale cavitation model. A volume of fluid (VOF) method simulates the large cavity, whereas a Lagrangian discrete bubble model (DBM) tracks the small bubbles. Meanwhile, noise is determined using the Ffowcs Williams-Hawkings equation (FW-H). Eulerian-Lagrangian analysis has shown that, in comparison to VOF, it is more effective in revealing microscopic characteristics of unsteady cavitating flows, including microscale bubbles, that are unresolvable around the cloud cavity, and their impact on the flow field. It is also evident that its evolution of cavitation features on the hydrofoil is more consistent with the experimental observations. The frequency of the maximum sound pressure level corresponds to the frequency of the main cavity shedding for the noise characteristics. Using the Eulerian-Lagrangian method to predict the noise signal, results show that the cavitation noise, generated by discrete bubbles due to their collapse, is mainly composed of high-frequency signals. In addition, the frequency of cavitation noise induced by discrete microbubbles is around 10 kHz. A typical characteristic of cavitation noise, including two intense pulses during the collapsing of the cloud cavity, is described, as well as the mechanisms that underlie these phenomena. The findings of this work provide for a fundamental understanding of cavitation and serve as a valuable reference for the design and intensification of hydrodynamic cavitation reactors.

Influence of Fluid Food Viscosity on Internal Flow Characteristics of Conveying Pump.

A fluid food conveying pump is used to convey edible or nutritional fluids and semi-fluids (containing suspended soft and hard particles and with different viscosities), such as water, glycerin, yogurt, and juice concentrate. Since different fluid food have different viscosities, the internal flow characteristics and conveying performance of food conveying pump are greatly affected by viscosity. To obtain the influence law of fluid food viscosity on the internal flow characteristics of the pump, the internal flow characteristics of food conveying pump when conveying food of 4 different viscosities (water, glycerin, 67.2 °Bx wild jujube juice, and 71.0 °Bx haw juice) were compared and observed in this study. The results showed that, with the increase in food viscosity, the overall flow loss in the pump, the entropy generation, and the proportion of total entropy generation in the pump chamber increase, but the conveying performance of the food conveying pump gets worse; however, the pressure pulsation intensity caused by static and dynamic interferences decreases with the increase in viscosity.

Prediction of Newtonian Droplet Breaking Time from a Capillary at Low Weber Numbers.

Droplet formation and growth processes have numerous scientific and industrial applications. Experimental and numerical studies on the formation, growth, and breaking of droplet are carried out in present work. The numerical results are in good agreement with the experiment. This work focused on the effect of different Weber numbers (We) on the droplet breaking time. The results show when We < 0.05, the length and volume of the droplet increase, and the breaking time decreases rapidly. The resultant force acting on the main droplet suddenly drops around the critical breaking time. The difference rate between the time t n (when the resultant force is zero) and the breaking time t b is less than 8.49%. For the dimensional analysis of the numerical results, a prediction formula of breaking time on the Weber number is modeled as aWe b + c for We < 0.5.

Research Status and Prospect for Vibration, Noise and Temperature Rise-Based Effect of Food Transport Pumps on the Characteristics of Liquid Foods.

In the field of food processing, the processing of liquid foods has always played an important role. Liquid foods have high requirements for the processing environment and equipment. As the core equipment in liquid foods processing, food transport pumps are widely used in liquid foods production, processing and transportation. Most liquid foods are non-Newtonian and vulnerable to vibration, noise, and temperature rise produced by rotary motions of food transport pumps in operation, which can finally affect foods safety. Therefore, this review summarizes the impact of mechanical vibration, noise, and temperature rise on liquid food products, with the aim of ensuring food safety while designing a cleaner, safer and more reliable food transport pumps in the future.

Small-scale fluctuation and scaling law of mixing in three-dimensional rotating turbulent Rayleigh-Taylor instability.

The effect of rotation on small-scale characteristics and scaling law in the mixing zone of the three-dimensional turbulent Rayleigh-Taylor instability (RTI) is investigated by the lattice Boltzmann method at small Atwood number. The mixing zone width h(t), the root mean square of small scale fluctuation, the spectra, and the structure functions are obtained to analyze the rotating effect. We mainly focus on the process of the development of plumes and discuss the physical mechanism in the mixing zone in rotating and nonrotating systems. The variation of kinetic energy spectra E_{u} and temperature energy spectra E_{θ} with the dimensionless rotation Ωτ demonstrate the suppression effect of rotation. Two scaling laws between the mixing layer width h(t) and dimensionless time t/τ are obtained at various Coriolis forces(sqrt[h(t)]≃t^{0.9} and sqrt[h(t)]≃t^{0.35}). The rotation increasingly suppresses the growth of the mixing layer width h(t). The velocity and temperature fluctuations are also suppressed by the rotation effect. The relation between the Nusselt number (Nu) and the Rayleigh number (Ra) indicates that the heat transfer is suppressed by the rotation effect in the rotating RT system. The width of the inertial subrange increasingly narrows with increasing Ωτ.

Carbon Nanomaterials: Application and Prospects of Urban and Industrial Wastewater Pollution Treatment Based on Abrasion and Corrosion Resistance.

Environmental pollution as a result of urban and industrial wastewater has become an increasingly prominent issue. Rivers, lakes, and oceans that have become eutrophicated or polluted by suspended solids and hazardous substances in wastewater have endangered the environment. A root cause of this is the discharge of untreated urban and industrial wastewater into the ecosystem. As a solution to the pollution, wastewater treatment facilities have seen increasingly rapid development. Sewage pumps are designed to transport urban and industrial wastewater containing solid particles or hazardous substances to water treatment centers for purification and treatment. Sewage pumps are of great importance in the entire wastewater treatment system. Sewage in the environment where sewage pumps work usually contains sands, suspended particles, and plenty of saline ions. Flow passage components and sealing elements of the pump become vulnerable to abrasion and chemical corrosion, which further challenges operational stability of the pump. Research has remained focused on how to improve reliability of sewage pumps under severe conditions. Because of advances in materials science, the application of an increasing number of new materials has been witnessed, such as carbon-based composite materials and carbon nanomaterials, thanks to their fine self-lubrication performance, heat resistance, thermal and electrical conductivity, chemical stability, heat and seismic resistance, as well as plasticity. These properties contribute to enormous potential that new carbon-based composite materials and carbon nanomaterials have to offer in terms of corrosion resistance. This paper outlines application scenarios, research progress, and the prospect of new materials in sewage pumps.