Cellulose microspheres enhanced polyvinyl alcohol separator for high-performance lithium-ion batteries.

Separators typically play an important role in enhancing the electrochemical performance of lithium-ion batteries (LIBs), while the preparation of separators suffers good electrochemical performance and high stability. In this study, regenerated porous cellulose microspheres (RCM) were innovatively fabricated and the biodegradable RCM/Polyvinyl alcohol (PVA) separators were successfully prepared through simple mixing and solvent substitution. Interestingly, the RCM with rich carboxylic groups, not only function as nanofillers that increases the strength properties of the three-dimensional porous network, but also enhances Li+ transfer (due to the COO- and Li+ interactions), resulting in outstanding Li+ transference number (0.54) of the RCM/PVA separator. In addition, the RCM/PVA separator shows excellent thermal stability and high liquid absorption rate (481.25 %). The LiFePO4/3 % RCM-HCl/PVA/Li cell displayed a high discharge capacity of 152.6 mAh·g-1 after 200 cycles at 1C. This work provides a new light on the fabrication of biodegradable separators for LIBs via a novel and cost-effective strategy.

Review of chemical pretreatment of lignocellulosic biomass using low-liquid and low-chemical catalysts for effective bioconversion.

Chemical pretreatment of lignocellulosic biomass (LCB) is essential for effective biological conversion in subsequent steps to produce biofuels or biochemicals. For effective pretreatment, high lignin content and its recalcitrant nature of LCB are major factors influencing bioconversion, especially lignin is known to be effectively solubilized by alkaline, organic, and deep eutectic solvents, ionic liquids, while hemicellulose is effectively dissolved by various acid catalysts and organic solvents. Depending on the pretreatment method/catalyst used, different pretreatment process scheme should be applied with different amounts of catalyst and water inputs to achieve a satisfactory effect. In addition, the amount of processing water required in the following processes such as washing, catalyst recovery, and conditioning after pretreatment is critical factor for scale-up (commercialization). In this review, the amount of catalyst and/or water used, and the effect of pretreatment, properties of the products, and recovery of liquid are also discussed.

Conductive Hydrogels Based on Industrial Lignin: Opportunities and Challenges.

The development of green materials, especially the preparation of high-performance conductive hydrogels from biodegradable biomass materials, is of great importance and has received worldwide attention. As an aromatic polymer found in many natural biomass resources, lignin has the advantage of being renewable, biodegradable, non-toxic, widely available, and inexpensive. The unique physicochemical properties of lignin, such as the presence of hydroxyl, carboxyl, and sulfonate groups, make it promising for use in composite conductive hydrogels. In this review, the source, structure, and reaction characteristics of industrial lignin are provided. Description of the preparation method (physical and chemical strategies) of lignin-based conductive hydrogel is elaborated along with their several important properties, such as electrical conductivity, mechanical properties, and porous structure. Furthermore, we provide insights into the latest research advances in industrial lignin conductive hydrogels, including biosensors, strain sensors, flexible energy storage devices, and other emerging applications. Finally, the prospects and challenges for the development of lignin-conductive hydrogels are presented.

Separation of saccharides from prehydrolysis liquor of lignocellulose to upgrade dissolving pulp mill into biorefinery platform.

In this work, a competitive process consisting of polyelectrolyte flocculation, active carbon absorption, and ion exchange was developed for hemicelluloses-derived saccharides (HDSs) purification from prehydrolysis liquor (PHL) of lignocellulose. Results showed that colloidal lignin counted for 20% of non-saccharide compounds (NSCs) and could be eliminated by flocculation at 500mg/L polyaluminium chloride and 50mg/L anionic polyacrylamide. Active carbon was very effective for decoloration of flocculation-treated PHL, but showed limited absorption selectivity toward NSCs. Lignin, the dominant component of NSCs, is characterized with phenolic hydrogen groups. Phenolic lignin could be easily captured by anion exchange resin with 80% removal. The proposed process showed great industrial potential because of the high value saccharides, but also low molecular phenolic lignin.

Separation of hemicellulose-derived saccharides from wood hydrolysate by lime and ion exchange resin.

A combined process of lime treatment and mixed bed ion exchange was proposed to separate hemicellulose-derived saccharides (HDS) from prehydrolysis liquor (PHL) of lignocellulose as value added products. The optimization of lime treatment achieved up to 44.2% removal of non-saccharide organic compounds (NSOC), mainly colloidal substances, with negligible HDS degradation at 0.5% lime level and subsequent neutralization by phosphoric acid. The residual NSOC and calcium ions in lime-treated PHL were eliminated by mixed bed ion exchange. The breakthrough curves of HDS and NSOC showed selective retention toward NSOC, leading to 75% HDS recovery with 95% purity at 17 bed volumes of exchange capacity. In addition, macroporous resin showed higher exchange capacity than gel resin as indicated by the triple processing volume. The remarkable selectivity of the combined process suggested the feasibility for HDS separation from PHL.

Limited adsorption selectivity of active carbon toward non-saccharide compounds in lignocellulose hydrolysate.

Prehydrolysis of lignocellulose produces abundant hemicellulose-derived saccharides (HDS). To obtain pure HDS for application in food or pharmaceutical industries, the prehydrolysis liquor (PHL) must be refined to remove non-saccharide compounds (NSC) derived from lignin depolymerization and carbohydrate degradation. In this work, activated carbon (AC) adsorption was employed to purify HDS from NSC with emphasis on adsorption selectivity. The adsorption isotherms showed the priority of NSC to be absorbed over HDS at low AC level. However, increase of AC over 90% of NSC removal made adsorption non-selective due to competitive adsorption between NSC and HDS. Size exclusion chromatography showed that the adsorption of oligomeric HDS was dominant while monomeric HDS was inappreciable. The limited selectivity suggested that AC adsorption is infeasibility for HDS purification, but applicable as a pretreatment method.

Separation and purification of hemicellulose-derived saccharides from wood hydrolysate by combined process.

Prehydrolysis of wood biomass prior to kraft cooking provides a stream containing hemicellulose-derived saccharides (HDSs) but also undesired non-saccharide compounds (NSCs) that were resulted from lignin depolymerization and carbohydrate degradation. In this study, a combined process consisting of lime treatment, resin adsorption, and gel filtration was developed to separate HDSs from NSCs. The macro-lignin impurities that accounted for 32.2% of NSCs were removed by lime treatment at 1.2% dosage with negligible HDSs loss. The majority of NSCs, lignin-derived phenolics, were eliminated by mixed bed ion exchange resin, elevating NSCs removal to 94.0%. The remaining NSCs, furfural and hydroxymethylfurfural, were excluded from HDSs by gel filtration. Chemical composition analysis showed that xylooligosaccharides (XOS) with the degree of depolymerization from 2 to 6 accounted for 28% of the total purified HDSs.