RESUMO
Doping (or substitution)-induced modification of the electronic structure to increase the electronic density of states (eDOS) near the Fermi level is considered as an effective strategy to enhance the Seebeck coefficient, and may consequently boost the thermoelectric performance. Through density-functional theory calculations of Mn-substituted TiFe2-xMnxSn compounds, we demonstrate that the d-states of the substituted Mn atoms induce a strong resonant level near the Fermi energy. Our experimental results are in good agreement with the calculations. They show that Mn substitution results in a large increase of the Seebeck coefficient, arising from an enhanced eDOS in Heusler compounds. The results prove that a proper substitution position and element selection can increase the eDOS, leading to a higher Seebeck coefficient and thermoelectric performance of ecofriendly materials.
RESUMO
A series of Ba1-xEuxTiO3-δ (0.1 ≤ x ≤ 0.9) phases with â¼40 nm particle size were synthesized via a Pechini method followed by annealing and sintering under a reducing atmosphere. The effects of Eu2+ substitution on the BaTiO3 crystal structure and the thermoelectric transport properties were systematically investigated. According to synchrotron X-ray diffraction data only cubic perovskite structures were observed. On the local scale below about 20 Å (equal to â¼5 unit cells) deviations from the cubic structure model (Pm3[combining macron]m) were detected by evaluation of the pair distribution function (PDF). These deviations cannot be explained by a simple symmetry breaking model like in EuTiO3-δ. The best fit was achieved in the space group Amm2 allowing for a movement of Ti and Ba/Eu along ã110ã of the parent unit cell as observed for BaTiO3. Density functional calculations delivered an insight into the electronic structure of Ba1-xEuxTiO3-δ. From the obtained density of states a significant reduction of the band gap by the presence of filled Eu2+ 4f states at the top of the valence band was observed. The physical property measurements revealed that barium-europium titanates exhibit n-type semiconducting behavior and at high temperature the electrical conductivity strongly depended on the Eu2+ content. Activation energies calculated from the electrical conductivity and Seebeck coefficient data indicate that at high temperatures (800 K < T < 1123 K) the conduction mechanism of Ba1-xEuxTiO3-δ (0.1 ≤ x ≤ 0.9) is a polaron hopping when 0 < x ≤ 0.6 and is a thermally activated process when 0.6 < x < 1. Besides, the thermal conductivity increases with increasing Eu2+ concentration. Due to a remarkable improvement of the power factor, Ba0.1Eu0.9TiO3-δ showed a ZT value of 0.24 at 1123 K.
RESUMO
Platinum (Pt) and Pt-based alloys have been extensively studied as efficient catalysts for both the anode and cathode of direct methanol fuel cells (DMFC). Defect engineering has been revealed to be practicable in tuning the charge transfer between Pt and transition metals/supports, which leads to the charge density rearrangement and facilitates the electrocatalytic performance. Herein, Pr-doped CeO2 nanocubes were used as the noncarbon support of a PtCu catalyst. The concentration and structure of oxygen vacancy (Vo) defects were engineered by Pr doping. Besides the Vo monomer, the oxygen vacancy with a linear structure is also observed, leading to the one-dimensional PtCu. The Vo concentration shows the volcanic scenario as Pr increased. Accordingly, the activities of PtCu/PrxCe1-xO2 toward methanol oxidation and oxygen reduction reactions exhibit the volcanic scenario. PtCu/Pr0.15Ce0.85O2 exhibits the optimal catalytic performance with the specific activity 3.57 times higher than that of Pt/C toward MOR and 1.34 times higher toward ORR. The MOR and ORR mass activities of PtCu/Pr0.15Ce0.85O2 reached 1.05 and 0.12 A·mg-1, which are 3.09 and 0.92 times the values of Pt/C, respectively. The abundant Vo afforded surplus electrons, which tailored the electron transfer between PtCu and PrxCe1-xO2, leading to enhanced catalytic performance of PtCu/PrxCe1-xO2. DFT calculations on PtCu/Pr0.15Ce0.85O2 revealed that Pr doping reduced the band gap of CeO2 and lowered the overpotential.
RESUMO
It is a major challenge to elevate the thermoelectric figure of merit ZT of materials through enhancing their power factor (PF) and reducing the thermal conductivity at the same time. Experience has shown that engineering of the electronic density of states (eDOS) and the energy filtering mechanism (EFM) are two different effective approaches to improve the PF. However, the successful combination of these two methods is elusive. Here we show that the PF of ß-Zn4Sb3 can greatly benefit from both effects. Simultaneous resonant distortion in eDOS via Pb-doping and energy filtering via introduction of interface potentials result in a ~40% increase of PF and an approximately twofold reduction of the lattice thermal conductivity due to interface scattering. Accordingly, the ZT of ß-Pb0.02Zn3.98Sb3 with 3 vol.% of Cu3SbSe4 nanoinclusions reaches a value of 1.4 at 648 K. The combination of eDOS engineering and EFM would potentially facilitate the development of high-performance thermoelectric materials.
RESUMO
Large-scale fabrication of nanostructured Cu3SbSe4 and its Sn-doped sample Cu3Sb0.98Sn0.02Se4 through a low-temperature co-precipitation route is reported. The effects of hot-pressing temperatures, time and Sn doping on the thermoelectric properties of Cu3SbSe4 are explored. The maximum figure of merit ZTmax obtained here reaches 0.62 for the un-doped Cu3SbSe4, which is three times as large as that of Cu3SbSe4 synthesized by the fusion method. Due to the ameliorated power factor by optimized carrier concentration and the reduced lattice thermal conductivity by enhanced phonon scattering at grain interfaces, Sn doping leads to an improvement of thermoelectric performance as compared to Cu3SbSe4. The maximum ZT for Cu3Sb0.98Sn0.02Se4 is 1.05 in this work, which is 50% larger than the largest value reported.