Ultrasonic activation of adhesive systems increases bond strength and intratubular penetration of resin cement in root dentin subjected to radiation therapy.

OBJECTIVE: This study aimed to evaluate the effect of ultrasonic activation of etch-and-rinse and self-etch adhesive systems on the bond strength of resin cement to irradiated root dentin. MATERIALS AND METHODS: Eighty human maxillary anterior teeth were distributed into 8 groups (n = 10), according to the type of adhesive system used (etch-and-rinse and self-etch), the ultrasonic activation of the adhesive systems, and the dentin condition (irradiated or non-irradiated - 70 Gy). Endodontic treatment was performed followed by fiberglass post-space preparation. After fiberglass posts' luting, the roots were transversely sectioned on dentin discs and submitted to the push-out bond strength test (0.5 mm/min). The fractured specimens were analyzed under a stereomicroscope and Scanning Electron Microscope (SEM) for failure mode classification. One of the dentin discs was analyzed under SEM to evaluate the characteristics of the adhesive interface. RESULTS: Irradiated specimens had lower bond strength than non-irradiated specimens (P < 0.0001). Ultrasonic activation of both adhesive systems increased the bond strength of the resin cement to irradiated dentin (P < 0.0001). Radiotherapy significantly affected the failure mode in the middle (P = 0.024) and apical thirds (P = 0.032) (adhesive failure). CONCLUSION: Non-irradiated specimens had a more homogeneous adhesive interface. When ultrasonically activated, both adhesive systems showed a greater number of resinous tags, regardless of the dentin condition. CLINICAL RELEVANCE: Ultrasonic activation of adhesive systems is a feasible strategy to enhance fiberglass posts retention in oncological patients.

Engineered Peptides Enable Biomimetic Route for Collagen Intrafibrillar Mineralization.

Overcoming the short lifespan of current dental adhesives remains a significant clinical need. Adhesives rely on formation of the hybrid layer to adhere to dentin and penetrate within collagen fibrils. However, the ability of adhesives to achieve complete enclosure of demineralized collagen fibrils is recognized as currently unattainable. We developed a peptide-based approach enabling collagen intrafibrillar mineralization and tested our hypothesis on a type-I collagen-based platform. Peptide design incorporated collagen-binding and remineralization-mediating properties using the domain structure conservation approach. The structural changes from representative members of different peptide clusters were generated for each functional domain. Common signatures associated with secondary structure features and the related changes in the functional domain were investigated by attenuated total reflectance Fourier-transform infrared (ATR-FTIR) and circular dichroism (CD) spectroscopy, respectively. Assembly and remineralization properties of the peptides on the collagen platforms were studied using atomic force microscopy (AFM). Mechanical properties of the collagen fibrils remineralized by the peptide assemblies was studied using PeakForce-Quantitative Nanomechanics (PF-QNM)-AFM. The engineered peptide was demonstrated to offer a promising route for collagen intrafibrillar remineralization. This approach offers a collagen platform to develop multifunctional strategies that combine different bioactive peptides, polymerizable peptide monomers, and adhesive formulations as steps towards improving the long-term prospects of composite resins.

[Treatment of 52 patients with a self-adhesive siliconised superabsorbent dressing: a multicentre observational study]. / Lechenie ran u 52 patsientov s primeneniem samokleyashcheisya silikonizirovannoi superabsorbiruyushchei povyazki: mnogotsentrovoe nablyudatel'noe issledovanie.

OBJECTIVE: To provide 'in use' clinical data to support exudate management in patients with moderately to highly exuding wounds with bordered superabsorbent wound dressing with a silicone adhesive interface Zetuvit Plus Silicone Border (Paul Hartmann Ltd., Germany). MATERIALS AND METHODS: This study was an open-labelled non-comparative study. Patients included in the study were selected by the clinical investigator(s) according to whether the patient required a dressing for the management of moderately to highly exuding wounds such as pressure ulcers, diabetic foot ulcers, venous leg ulcer and arterial ulcers The patients were treated with A superabsorbent sterile wound dressing with bordered superabsorbent wound dressing with a silicone adhesive interface Zetuvit Plus Silicone Border (Paul Hartmann Ltd., Germany). RESULTS: The Zetuvit Plus Silicone Border dressing had met the clinical objectives relating to exudate management, affirmed by the health professionals with a yes response in 94% of cases. Additionally, the health professionals rated the handling of exudate as excellent/good (78%) and most (80%) reported that they would use the superabsorbent wound dressing with a silicone adhesive interface again. Allied to this was the fact that the dressing improved the wound edge and periwound skin conditions (29% and 36% of patients, respectively). The dressing retained its position in 72% of patients. For wear time, the largest proportion of dressing changes, both pre-study and during the evaluation period, was every third day (45% and 44%, respectively). But there was a shift to extended wear time with use of the superabsorbent wound dressing with a silicone adhesive interface with 72% of patients' dressing changes being every third day or longer. CONCLUSION: The superabsorbent silicone border dressing was successful in managing wound exudate in moderately to highly exuding wounds and consequently this had a beneficial impact on the wound edge and periwound skin. Overall, there was a positive effect on wound bed preparation and in turn the healing response was progressive.

Influence of proanthocyanidins combined with ethanol-wet bonding on the bonding quality of fibre posts to root dentine.

This study evaluated the influence of a bonding approach using proanthocyanidins (PAs) combined with ethanol-wet bonding (EWB) and a hydrophobic adhesive on the bonding quality of fibre posts. After endodontic treatment and post-space preparation, 72 single-rooted extracted human teeth were etched, thoroughly rinsed, and then treated using the following procedures (n = 24 teeth per group): group 1, no pretreatment; group 2, pretreatment with absolute ethanol three times, for 30 s each time; or group 3, pretreatment with absolute ethanol solution containing 5% PAs three times, for 30 s each time. Six teeth per group were dried according to a dry and a wet drying protocol and then observed using field emission-scanning electron microscopy. The remaining 18 teeth in each group were cemented with fibre posts: All-Bond 3 and Duo-Link cement were used for group 1; and hydrophobic adhesive and Duo-Link cement were used for groups 2 and 3. Push-out bond strength, failure mode, and nanoleakage were evaluated immediately and after collagenase treatment. Higher push-out bond strength and less nanoleakage were observed in the two ethanol-pretreatment groups, regardless of storage conditions. Teeth pretreated with PAs + ethanol exhibited significantly higher push-out bond strength after collagenase treatment than did teeth pretreated with ethanol alone. Within the limits of this study, the bonding approach of PAs combined with EWB and a hydrophobic adhesive synergistically improved the durability of fibre post bonds.

Graphene oxide-based experimental silane primers enhance shear bond strength between resin composite and zirconia.

Despite various mechanical and chemical surface-pretreatment methods, long-term bonding of resin composite to dental zirconia (ZrO2 ) remains a major concern. In this study, graphene oxide (GO) sheets were infused into two commercially available primers and the enclosed mould shear bond strength (EM-SBS) of resin composite to ZrO2 was evaluated. Twelve fully sintered ZrO2 blanks were pretreated and randomly allocated to four groups according to the primers used: RelyX (RX); GO blended RelyX (RXGO); Monobond-S (MB); and GO blended Monobond-S (MBGO). The resin composite stubs were bonded onto the pretreated ZrO2 surfaces and analysed at baseline and after storage in distilled water for 2 and 4 months. The experimental primers blended with GO sheets influenced the surface morphology, visualized as increased surface roughness, and slightly increased the water contact angle measurements. Moreover, the infusion of primers with GO increased the mass fraction (wt%) of carbon and oxygen. The highest EM-SBS values were found for RXGO, with mean (SD) EM-SBS values of 26.4 (3.7) MPa and 21.5 (5.1) MPa after 2 and 4 months of storage, respectively. Infusion of silane primers with nanometre- to micrometre-size GO sheets enhanced the SBS between resin composite and ZrO2 .

Longevity of bond strength of resin cements to root dentine after radiation therapy.

AIM: To evaluate the bond strength and adhesive interface between several resin cements and root dentine immediately and 6 months after radiotherapy. METHODOLOGY: Sixty maxillary canines were selected and randomly assigned to two groups (n = 30): one group was not irradiated and the other one was subjected to a cumulative radiation dose of 60 Gy. The teeth were sectioned to obtain roots 16 mm long and the canals were prepared with the Reciproc system (R50) and filled using a lateral condensation technique with an epoxy resin sealer. Each group was divided into three subgroups (n = 10) according to the resin cement used for fibreglass fibre post cementation: RelyX-U200, Panavia-F2.0 and RelyX ARC. The posts were cemented in accordance with the manufacturer's recommendations. Three 1-mm-thick dentine slices were then obtained from each root third. The first two slices in the crown-apex direction of each third were selected for the push-out test. The failure mode after debonding was determined with a stereo microscope. The third slice from each root third was selected for scanning electron microscopy (SEM) analyses to examine the resin cement-dentine interface with 100, 1000, 2000 and 4000× magnification. Bond strength data were analysed by anova and Tukey's test (α = 0.05). RESULTS: Significantly lower bond strength (P < 0.0001) was obtained after irradiation compared to nonirradiated teeth. RelyX-U200 cemented fibre posts had the higher bond strength (15.17 ± 5.89) compared with RelyX ARC (P < 0.001) and Panavia-F2.0 (P < 0.001). The evaluation after 6 months revealed lower bond strength values compared to the immediate values (P < 0.001) for irradiated and nonirradiated teeth. Cohesive failures occurred in the irradiated dentine. SEM revealed fractures, microfractures and fewer collagen fibres in irradiated root dentine. RelyX-U200 and Panavia-F2.0 were associated with a juxtaposed interface of the cement with the radicular dentine in irradiated and nonirradiated teeth, and for RelyX ARC, hybrid layer formation and tags were observed in both irradiated and nonirradiated teeth. CONCLUSION: Radiation was associated with a decrease in the push-out bond strength and with lower resin cement/root dentine interface adaptation. Self-adhesive resin cement was a better alternative for fibre post cementation in teeth subjected to radiation therapy. The bond strength decreased after 6 months.

Comparison of two observational methods, scanning electron and confocal laser scanning microscopies, in the adhesive interface analysis of endodontic sealers to root dentine.

OBJECTIVES: To compare the accuracy of confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM) during the analysis of the adhesive interface integrity and intratubular penetration of root canal sealers to radicular dentine. MATERIALS AND METHODS: Twenty roots of human maxillary incisors were prepared and distributed into two groups (n = 10), followed by filling with gutta-percha and Endofill (G1) or AH Plus (G2). After 7 days, roots were sectioned and analyzed under CLSM and SEM. Score systems were used to evaluate the adhesive interface integrity (0-4) and sealer intratubular penetration (0-3). Data were submitted to Wilcoxon-Mann-Whitney and Kendall correlation statistical tests (α = 5%). RESULTS: In the adhesive interface analysis, CLSM was similar (P = 0.157) to SEM for Endofill; however, the results were different for AH Plus (P = 0.029). Intratubular penetration had significant difference between observational methods for both sealers (P < 0.0001). Correlation analysis between SEM and CLSM for adhesive interface was moderate for Endofill and low for AH Plus. Intratubular penetration was low for both sealers. CONCLUSION: SEM and CLSM analysis had similar results when sealers were compared, with a more homogeneous adhesive interface, and greater intratubular penetration for AH Plus. Comparison between observational methods demonstrated low positive correlation for adhesive interface and intratubular penetration analysis. CLINICAL RELEVANCE: A proper interface formed between sealer and dentine is very important for final quality of root canal filling. Observational methods which allow an accurate analysis of this interface must be selected to assess such features.

Mechanistic study of the stabilization of dentin-bonded restorative interfaces via collagen reinforcement by multi-acrylamides.

Hydrolytically and enzymatically-stable multi-acrylamides have been proposed to increase the long-term durability of dental adhesive interfaces as alternatives to methacrylates. The aim of this study was to investigate the mechanical and biochemical properties of experimental adhesives containing multi-functional acrylamides concerning collagen reinforcement and metalloproteinases (MMP) activity. Multi-functional acrylamides, TMAAEA (Tris[(2-methylaminoacryl) ethylamine) and DEBAAP (N,N-Diethyl-1,3-bis(acrylamido) propane), along with the commercially available DMAM (N,N-dimethylacrylamide) (monofunctional acrylamide) and HEMA (2-Hydroxyethyl methacrylate) (monofunctional methacrylate - control) were tested for stability against enzymatic hydrolysis by cholesterol esterase/pseudocholinesterase (PC/PCE) solutions for up to 30 days. Collagen-derived substrate and gelatin zymography were performed to examine the effect of the compounds on the biological activity of human recombinant and dentin-extracted gelatinases MMP-2 and MMP-9. In situ zymography was carried out by fluorescent collagen degradation combined with confocal microscopy analysis. Hydroxyproline content was measured in collagen derived from dentin extracts though reaction with Ehrlich's reagent p-dimethylaminobenzaldehyde (DMAB), generating a stable chromophore measured at 550 nm. Storage shear modulus of demineralized dentin discs treated with the tested compounds was measured by oscillatory rheometry, in order to investigate potential collagen reinforcement. FT-IR was performed to determine qualitative differences in collagen based on observed changes in amide bands. The results were analyzed by ANOVA/Tukey's test (α = 0.05). Multi-acrylamides survived 30 days of incubation in cholinesterase/pseudo-cholinesterase (PC/PCE) solutions, while HEMA showed approximately 70 % overall degradation. Incubation with multi-acrylamides reduced collagen degradation as evidenced by the reduced hydroxyproline levels and by the 30 % increase inshear storage modulus. Biochemical and zymography assays showed no noticeable inhibition of recombinant and extracted MMPs enzymatic activity. The infra-red spectroscopy results for multi-functional acrylamides treated samples demonstrated shifts of the amide II bonds and marked increase in intensity of the bands 1200 cm-1, which may indicate partial collagen denaturation and some degree of cross-linking of the compounds with collagen, respectively. The multi-acrylamides exhibited not only comparable mechanical properties but also demonstrated significantly enhanced biochemical stability when compared to the widely used methacrylate control. Clinical relevance: These findings highlight the potential of multi-acrylamides to increase the bonding stability to tissues and, ultimately, contribute to the longevity of dental restorations.

Analysis of physicochemical properties of endodontic sealers containing rhodamine B.

The use of fluorescent dyes in microscopy studies is frequent. Therefore, it is important to investigate whether these compounds may alter the physicochemical properties of materials in which they are incorporated to avoid methodological biases. This study evaluated the physicochemical properties of two endodontic sealers containing dry or diluted rhodamine B. Six groups were evaluated: AH Plus and MTA Fillapex in their original composition and mixed with 0.1% dry or diluted rhodamine. Push-out test was applied to assess the bond strength to root dentin. ANSI-ADA No. 57 and ISO No. 6876:2012 specifications were followed to evaluate flowability, setting time, and solubility of the sealers. pH changes were assessed after 24 h, 7, and 30 days. Intergroup comparisons were analyzed by ANOVA complemented by Tukey's post-hoc test; comparisons among periods were analyzed by Wilcoxon and Friedman tests. The incorporation of dry rhodamine decreased the bond strength and prolonged the setting time of AH Plus. The incorporation of diluted rhodamine decreased the setting time and increased the flowability of MTA Fillapex. Diluted rhodamine promoted pH reduction of AH Plus after 24 h and dry rhodamine after 7 days. Rhodamine incorporation promoted pH reduction after 30 days for MTA Fillapex. Solubility was not affected. In conclusion, the incorporation of diluted rhodamine changed the properties of MTA Fillapex, and the incorporation of dry rhodamine changed the properties of AH Plus. Previous dilution of rhodamine did not severely compromise the physicochemical properties of AH Plus and may be suggested to assess its penetrability.

An In-Vitro Analysis of the Surface Treatment of Orthodontic Bracket Bases With Er,Cr:YSGG Laser and Its Effect on Shear Bond Strength.

Introduction Shear bond strength is indispensable to prevent the debonding of orthodontic brackets. Lasers have been proven to alter the bond strength of orthodontic brackets, but their efficiency has not been validated in many trials. The study aimed to evaluate the impact of the Er,Cr:YSGG laser on the bases of orthodontic brackets and determine their bond strength with the enamel surface. Materials and methods The Waterlase iPlus (made in the USA in 2012), comprising an Er,Cr:YSGG laser, was used. Based on the surface treatment of brackets, two groups were assigned (n=10), comprising laser-treated and untreated bracket bases. The brackets were treated with the minimum laser intensity (50 Hz, 4.5 W). Then, the brackets of both groups were attached to the labial surfaces of previously extracted premolars, respectively. The shear bond strength of brackets (SBS) was assessed using the universal testing device, and the Adhesive Remnant Index (ARI) was also measured. An independent sample t-test was used to compare the bond strength between the laser-treated and untreated brackets. Results The mean bond strength of laser-treated and control group brackets was 5 MPa and 8.63 MPa, respectively. The laser-treated brackets showed lower bond strength than the control brackets, but the results were statistically insignificant (p=0.23). The ARI analysis stated that bond failures occurred mostly in the region of the bracket and adhesive interface. Conclusion Laser-etched bracket bases showed lesser shear bond strength than the untreated ones, though the difference was statistically insignificant.

Interfacial Characterization of a Conventional Glass-Ionomer Cement after Functioning for 1-year In Vivo.

PURPOSE: To morphologically evaluate the interface between a conventional glass-ionomer cement (GIC) and dentin one day after placement, as well as the changes at the interface after one year of aging/functioning in monkey teeth. MATERIALS AND METHODS: On the buccal surfaces of seven intact teeth in each of two monkeys, shallow class V cavities were prepared, which were then filled with Fuji IX GP (GC) to provide 1-year in vivo data. A year later, two more teeth in each monkey were similarly prepared and restored for the 1-day in vivo group. The following day, the restored teeth were extracted and the restoration interfaces observed using transmission electron microscopy (TEM). In addition, restorations were similarly placed in two extracted human teeth (control, 1-day in vitro group) and observed a day after placement using TEM. RESULTS: The 1-day in vivo and in vitro results showed that the GIC appeared to bond to dentin through a demineralized zone similar to the hybrid layer produced by resinous adhesives. However, the interface between GIC and dentin after 1 year in vivo appeared to change over time: many needle-like crystals were detected within the remineralized layer and along the collagen fibrils. Slow diffusion of ions resulted in pores, which filled with mineral crystals and made the pores smaller. CONCLUSION: The interface between GIC and dentin morphologically changes over time, and recrystallization or remineralization at the interface may occur (1 year in vivo).

Adsorption and removal of organophosphorus pesticides from Chinese cabbages and green onions by using metal organic frameworks based on the mussel-inspired adhesive interface.

Based on the mussel-inspired adhesive interface (Fe3O4-g-C3N4@PDA), a novel bionic metal-organic framework (Fe3O4-g-C3N4-PDA@MIL-101) was successfully prepared. The composite featured a high specific surface area and a multi-microchannel structure, as well as strong thermochemical stability. The structural property of Fe3O4-g-C3N4-PDA@MIL-101(Fe) was characterized, and the results indicated that Fe3O4, PDA, and MIL-101(Fe) were uniformly coated on the g-C3N4 surface. The adsorption and desorption of organophosphorus pesticides with Fe3O4-g-C3N4-PDA@MIL-101(Fe) were evaluated by batch experiments. This composite showed high adsorption efficiency and selective removal of coralox, phosalone, and chlorpyrifos. Under the optimal conditions, three organophosphorus pesticides were adsorbed from Chinese cabbage and green onion samples with Fe3O4-g-C3N4-PDA@MIL-101(Fe). The analytical method exhibited high sensitivity (LOD, 0.19-2.34 µg/L; LOQ, 0.65-7.82 µg/L), excellent practicality, and good stability, suggesting that Fe3O4-g-C3N4-PDA@MIL-101 was an ideal candidate magnetic adsorbent for the removal of organophosphorus pesticides in Chinese cabbage and green onion samples.

Substitution of urea-formaldehyde by renewable phenolic compound for environmentally appropriate production of particleboards.

In recent years, research has been conducted in search of alternative adhesives that are less harmful to human health and the environment. Cardanol derived from cashew nut shell liquid (CNSL) has attracted considerable attention due to its chemical and specific characteristics (antioxidant activity, flame resistance, and hydrophobicity). In this sense, this study aimed to evaluate the quality of particleboards using cardanol instead of urea-formaldehyde (UF) adhesive. Different percentages of cardanol were used (0, 20, 40, 60 and 80%) in which its physicochemical properties were evaluated. The panels were produced with particles of Pinus oocarpa and nominal density of 0.75 g/cm3, their physical and mechanical properties were evaluated, wood-adhesive interface evaluation with scanning electron microscopy (SEM), and the combustibility test. It is concluded that the maximum replacement of UF by cardanol is 5%, since, in this situation, the mentioned properties reach the established norms for the commercialization of the boards.

Application of Scanning Electron Microscopy in the observation of dentin-adhesive interface.

The objective of this study was observation of the adhesive interface on original tooth samples, as well as their epoxy replicas, under SEM. A light-cure flowable composite was incrementally placed and light-polymerized in previously prepared cylindrical dentinal cavities on the buccal surfaces of extracted human third molars. After finishing procedures, impressions of the composite/dentin margin were made using polyvinylsiloxane in order to obtain accurate epoxy replicas for SEM analysis. Ultrastructural morphology of the adhesive surface was observed at high magnifications (≥1,000×) on original tooth samples, which were previously prepared to expose the part of the dentin surface, which participates in the formation of adhesive bond. SEM micrographs showed that marginal adaptation was mostly of acceptable quality. In some of the SEM micrographs of original tooth samples, marginal gap formation, and resin tag breakdown were noted, which were ascribed to polymerization shrinkage. Profound understanding of ultrastructural morphology is necessary for achieving more predictable and durable margin between composite restorations and surrounding tooth structures, and SEM analysis can serve that purpose.

Effect of natural primer associated to bioactive glass-ceramic on adhesive/dentin interface.

OBJECTIVES: This study evaluated the effect of propolis associated with Biosilicate on the bond strength (BS) and gelatinolytic activity at the adhesive/dentin interface. METHODS: Occlusal cavities were prepared in 320 human molars. Half of them were submitted to cariogenic challenge. All the teeth were separated into eight groups (n = 20): Control - Adhesive System (Single Bond Universal, 3 MESPE); CHX - 0.12 % Chlorhexidine; Bio - 10 % Biosilicate; P16 - Propolis with low levels of polyphenols; P45 - Propolis with high levels of polyphenols; CHX Bio - CHX + Bio; P16 Bio - P16+Bio; P45 Bio - P45+Bio. The adhesive was applied (self-etch mode) after treatments. Restorations (Filtek Z350, 3 MESPE) were performed and samples sectioned into sticks, separated and stored in distilled water at 37 °C for 24 h, 6 months and 1 year. Microtensile BS (0.5 mm/min) was tested and analyzed (2-way ANOVA, Bonferroni's Test, p < .05 and Weibull analysis). Fracture patterns (VH-M100, Keyence) and adhesive interfaces (SEM, EVO-MA10, ZEISS and TEM, JEM-1010, JEOL) were observed; and biodegradation and in situ zymography performed. RESULTS: P16 presented the highest BS values on sound dentin after 6 months. In caries-affected dentin (CAD), the association of treatments promoted the highest BS after 24 h. Sound dentin obtained significantly higher Weibull modulus than CAD. SEM displayed resin tags in P16, P45 and association of treatments. TEM showed good interaction between adhesive and dentin. According to the in situ zymography and biodegradation assay all natural primers reduced the gelatinolytic activity. P45 presented the lowest biodegradation and enzymatic activity. CONCLUSIONS: Propolis and the association of treatments promoted the highest bond strength results and preserved the dentin. All the experimental groups exhibited low gelatinolytic activity. CLINICAL SIGNIFICANCE: Propolis and the association of treatments with Biosilicate could preserve the dentin substrate and improve the longevity of composite restorations.

Interfacial Adhesion of a Semi-Interpenetrating Polymer Network-Based Fiber-Reinforced Composite with a High and Low-Gradient Poly(methyl methacrylate) Resin Surface.

The research aimed to determine the tensile bond strength (TBS) between polymerized intact and ground fiber-reinforced composite (FRC) surfaces. FRC prepregs (a reinforcing fiber pre-impregnated with a semi-interpenetrating polymer network (semi-IPN) resin system; everStick C&B) were divided into two groups: intact FRCs (with a highly PMMA-enriched surface) and ground FRCs (with a low PMMA gradient). Each FRC group was treated with: StickRESIN and G-Multi PRIMER. These groups were further divided into four subgroups based on the application time of the treatment agents: 0.5, 1, 2, and 5 min. Next, a resin luting cement was applied to the FRC substrates on the top of the photo-polymerized treating agent. Thereafter, weight loss, surface microhardness, and TBS were evaluated. Three-factor analysis of variance (p ≤ 0.05) revealed significant differences in the TBS among the FRC groups. The highest TBS was recorded for the intact FRC surface treated with G-Multi PRIMER for 2 min (13.0 ± 1.2 MPa). The monomers and solvents of G-Multi PRIMER showed a time-dependent relationship between treatment time and TBS. They could diffuse into the FRC surface that has a higher PMMA gradient, further resulting in a high TBS between the FRC and resin luting cement.

ToF-SIMS Analysis of Demineralized Dentin Biomodified with Calcium Phosphate and Collagen Crosslinking: Effect on Marginal Adaptation of Class V Adhesive Restorations.

This study aimed to assess the effect of biomodification before adhesive procedures on the tooth-restoration interface of class V restorations located in caries-simulated vs. sound dentin, and the quality of dentin surface by time-of-flight secondary ion mass spectrometry (ToF-SIMS). Class V cavities located on cervical dentin were prepared on the buccal surfaces of extracted human molars under the simulation of intratubular fluid flow. Two dentin types, i.e., sound and demineralized by formic-acid, were biomodified with 1% riboflavin and calcium phosphate (CaP) prior to the application of a universal adhesive (Clearfil Universal Bond) in etch and rinse or self-etch mode, and a conventional micro hybrid composite (Clearfil APX). Restorations were subjected to thermo mechanical fatigue test and percentages of continuous margins (% CM) before/after fatigue were compared. Bio modification of dentin surfaces at the molecular level was analyzed by Time-of-Flight Secondary Mass Spectometry (ToF-SIMS). % CM were still significantly higher in tooth-restoration interfaces on sound dentin. Meanwhile, biomodification with riboflavin and CaP had no detrimental effect on adhesion and in carious dentin, it improved the % CM both before and after loading. Etching carious dentin with phosphoric acid provided with the lowest results, leading even to restoration loss. The presence of molecule fragments of riboflavin and CaP were detected by ToF-SIMS, evidencing dentin biomodification. The adhesive interface involving carious dentin could be improved by the use of a collagen crosslinker and CaP prior to adhesive procedures.

Synthesis of di- and triacrylamides with tertiary amine cores and their evaluation as monomers in dental adhesive interfaces.

PURPOSE/AIM: In an attempt to increase the service life of dental adhesive interfaces, more hydrolytically and enzymatically-stable methacrylate alternatives, such as methacrylamides, have been proposed. The aim of this study was to investigate polymerization behavior, as well as mechanical and biological properties of experimental adhesives containing multi-functional acrylamides. MATERIALS AND METHODS: Multi-functional acrylamides (N,N-Bis[(3-methylaminoacryl)propyl]methylamine - BMAAPMA, Tris[(2-methylaminoacryl)ethyl]amine - TMAAEA, N,N'-bis(acrylamido) 1,4-diazepane - BAADA, N,N-Diethyl-1,3-bis(acrylamido)propane - DEBAAP) or HEMA (2-Hydroxyethyl methacrylate - control) were added at 40 wt% to UDMA. 0.2 wt% DMPA and 0.4 wt% DPI-PF6 were used as initiators. Polymerization kinetics was followed in real-time in near-IR during photoactivation (320-500 nm, at 630 mW/cm2). Water sorption/solubility and flexural strength/modulus were measured according to ISO 4049. 1H NMR was used to assess monomer degradation kinetics. MTT assay was used to assess cytotoxicity against OD-21 and DPSC cells. Biofilm formation and adhesion were assessed by Luciferase Assay and Impingement technique, respectively. Solvated adhesives (40 vol% ethanol) were used to test interfacial adhesion strength. The results were analyzed by ANOVA/Tukey's test (α = 0.05). RESULTS: In general, the pure methacrylate mixture had higher rate of polymerization (Rpmax), degree of conversion (DC) at Rpmax, and final DC than the acrylamides. Flexural properties after water storage decreased between 11 and 65%, more markedly for acrylamides. Interfacial bond strength was greater and more stable long-term for the newly synthesized acrylamide formulations (less than 4% reduction at 6 months) compared to the methacrylate experimental control (42% reduction at 6 months). HEMA degraded by almost 90%, while the acrylamides showed no degradation in acidic conditions. Cytotoxicity and biofilm formation, in general, were similar for all groups. CONCLUSIONS: Despite demonstrating high water sorption, the acrylamide-containing materials had similar mechanical and biological properties and enhanced interfacial bond strength stability compared to the methacrylate control.

Effect of Er:YAG and Burs on Coronal Dentin Bond Strength Stability.

PURPOSE: To evaluate the immediate and aged bond strength and interfacial nanolaekage of different adhesives and protocols on dental elements prepared with diamond burs and Er:YAG laser. MATERIALS AND METHODS: Forty molar crowns were flattened and a standardized smear layer was created. Teeth were divided into two main groups according to the dentin cutting technique: 1. Er:YAG laser for 30 s at 30 Hz repetition rate, 250 mJ energy per pulse, and water spray irrigation set at level 8; and 2. diamond bur. Each group was then divided into subgroups according to the adhesive protocol: SG1: dentin etching for 15 s followed by universal adhesive application (All Bond Universal, Bisco); SG2: universal adhesive application (All Bond Universal); SG3: two-step self-etch adhesive application (Clearfil SE Bond 2, Kuraray Noritake); SG4: etching followed by 3-step etch-and-rinse adhesive application (Optibond FL, Kerr). After curing the adhesives, resin composite buildups of 4 mm were made and specimens were sectioned to obtain 1-mm-thick sticks in accordance with the µTBS test technique. Sticks were stressed to failure at baseline and after 6 months of storage in artificial saliva. Three teeth per group were prepared for nanoleakage interfacial analyses. Data were statistically analyzed with three-way ANOVA and Tukey's post-hoc test (p < 0.05). RESULTS: A significant difference in bond strengths was found for treatment, aging, and adhesive protocol. Nanoleakage analysis showed higher marginal infiltration in Er:YAG-treated groups both at baseline and after aging. CONCLUSIONS: Surfaces prepared with diamond burs presented higher bond strengths than did those prepared with Er:YAG laser. Adhesive protocols and aging could influence the adhesive-dentin interface. Further studies are necessary to validate the results obtained.

Influence of Monomer Systems on the Bond Strength Between Resin Composites and Polymerized Fiber-Reinforced Composite upon Aging.

PURPOSE: This study examined the influence of different monomer systems on the tensile bond strength between a resin composite and a polymerized fiber-reinforced composite (FRC). The influence of the age (shelf-life) of the FRC prepreg (reinforcing fiber pre-impregnated with a resin system) before preparing the FRC substrate for the bonding test was also assessed. MATERIALS AND METHODS: Semi-interpenetrating polymer network (semi-IPN)-based glass FRC prepregs were aged for various durations (1, 1.5, and 3 years) at 4°C before being used to prepare FRC substrates via light polymerization. Four groups of aged prepregs were prepared through different treatments with: 1. no primer; 2. a dimethacrylate-based adhesive primer; 3. a universal primer; and 4. a specific composite primer. Subsequently, a resin composite luting cement was applied on the treated FRC substrates and cured with light. The water sorption of the FRC-composite specimens was determined. Then, the differences in the tensile bond strength were evaluated using ANOVA (p ≤ 0.05). RESULTS: There were significant differences in the tensile bond strength between the composite cement and the FRC according to the primer used (p < 0.001), aging time (p < 0.001), and their interactive effect (p < 0.001). CONCLUSION: The monomers of the universal primer demonstrated the best ability to diffuse into the semi-IPN structure of the polymer matrix of FRC. This improved the interfacial bond strength between the composite cement and the FRC substrate.