Synthesis and Characterization of Cross-Linked Aggregates of Peroxidase from Megathyrsus maximus (Guinea Grass) and Their Application for Indigo Carmine Decolorization.

We present the synthesis of a cross-linking enzyme aggregate (CLEAS) of a peroxidase from Megathyrsus maximus (Guinea Grass) (GGP). The biocatalyst was produced using 50%v/v ethanol and 0.88%w/v glutaraldehyde for 1 h under stirring. The immobilization yield was 93.74% and the specific activity was 36.75 U mg-1. The biocatalyst surpassed by 61% the free enzyme activity at the optimal pH value (pH 6 for both preparations), becoming this increase in activity almost 10-fold at pH 9. GGP-CLEAS exhibited a higher thermal stability (2-4 folds) and was more stable towards hydrogen peroxide than the free enzyme (2-3 folds). GGP-CLEAS removes over 80% of 0.05 mM indigo carmine at pH 5, in the presence of 0.55 mM H2O2 after 60 min of reaction, a much higher value than when using the free enzyme. The operational stability showed a decrease of enzyme activity (over 60% in 4 cycles), very likely related to suicide inhibition.

Cross-linked enzyme aggregates immobilization: preparation, characterization, and applications.

Enzymes are commonly used as biocatalysts for various biological and chemical processes. However, some major drawbacks of free enzymes (e.g. poor reusability and instability) significantly restrict their industrial practices. How to overcome these weaknesses remain considerable challenges. Enzyme immobilization is one of the most effective ways to improve the reusability and stability of enzymes. Cross-linked enzyme aggregates (CLEAs) has been known as a novel and versatile carrier-free immobilization method. CLEAs is attractive due to its simplicity and robustness, without purification. It generally shows: high catalytic specificity and selectivity, good operational and storage stabilities, and good reusability. Moreover, co-immobilization of different kinds of enzymes can be acquired. These CLEAs advantages provide opportunities for further industrial applications. Herein, the preparation parameters of CLEAs were first summarized. Next, characterization of structural and catalytic properties, stability and reusability are also proposed. Finally, some important applications of this technique in: environmental protection, industrial chemistry, food industry, and pharmaceutical synthesis and delivery are introduced. Potential challenges and future research directions, such as improving cross-linking efficiency and internal mass transfer efficiency, are also presented. This implies that CLEAs provide an efficient and feasible technique to improve the properties of enzymes for use in the industry.

(Magnetic) Cross-Linked Enzyme Aggregates of Cellulase from T. reesei: A Stable and Efficient Biocatalyst.

Cross-linked enzyme aggregates (CLEAs) represent an effective tool for carrier-free immobilization of enzymes. The present study promotes a successful application of functionalized magnetic nanoparticles (MNPs) for stabilization of cellulase CLEAs. Catalytically active CLEAs and magnetic cross-linked enzyme aggregates (mCLEAs) of cellulase from Trichoderma reesei were prepared using glutaraldehyde (GA) as a cross-linking agent and the catalytic activity and stability of the CLEAs/mCLEAs were investigated. The influence of precipitation agents, cross-linker concentration, concentration of enzyme, addition of bovine serum albumin (BSA), and addition of sodium cyanoborohydride (NaBH3CN) on expressed activity and immobilization yield of CLEAs/mCLEAs was studied. Particularly, reducing the unsaturated Schiff's base to form irreversible linkages is important and improved the activity of CLEAs (86%) and mCLEAs (91%). For increased applicability of CLEAs/mCLEAs, we enhanced the activity and stability at mild biochemical process conditions. The reusability after 10 cycles of both CLEAs and mCLEAs was investigated, which retained 72% and 65% of the initial activity, respectively. The thermal stability of CLEAs and mCLEAs in comparison with the non-immobilized enzyme was obtained at 30 °C (145.65% and 188.7%, respectively) and 50 °C (185.1% and 141.4%, respectively). Kinetic parameters were determined for CLEAs and mCLEAs, and the KM constant was found at 0.055 ± 0.0102 mM and 0.037 ± 0.0012 mM, respectively. The maximum velocity rate (Vmax) was calculated as 1.12 ± 0.0012 µmol/min for CLEA and 1.17 ± 0.0023 µmol/min for mCLEA. Structural characterization was studied using XRD, SEM, and FT-IR. Catalytical properties of immobilized enzyme were improved with the addition of reducent NaBH3CN by enhancing the activity of CLEAs and with addition of functionalized aminosilane MNPs by enhancing the activity of mCLEAs.

Preparation, characterization and stability of cross linked nitrilase aggregates (nitrilase-CLEAs) for hydroxylation of 2-chloroisonicotinonitrile to 2-chloroisonicotinic acid.

Nitrilases capable of performing hydroxylation of 2-chloroisonicotinonitrile to 2-chloroisonicotinic acid were screened, and ES-NIT-102 was the best nitrilase for said biotransformation. Nitrilase was immobilized as cross linked enzyme aggregates (nitrilase-CLEAs) by fractional precipitation with iso-propanol, and cross linked with glutaraldehyde. The nitrilase-CLEAs prepared with optimized 35 mM glutaraldehyde for 120 min cross linking time had 82.36 ± 4.45% residual activity, and displayed type-II structural CLEAs formation as confirmed by particle size, SEM, FTIR, and SDS-PAGE analysis. Nitrilase-CLEAs had superior pH and temperature stability, showed a shift in optimal temperature by 5 °C, and retained nearly 1.5 to 1.7 folds activity over free nitrilase at 50 °C and 55 °C after more than 9 h incubation. Nitrilase-CLEAs showed reduced affinity and decreased conversion of substrate as indicated by slightly higher Km values by 5.19% and reduced Vmax by 17%. Furthermore, these nitrilase-CLEAs showed 98% conversion, 94.72 g/L product formation, and 83.30% recovery after 24 h when used for hydroxylation of 2-chloroisonicotinonitrile to 2-chloroisonicotinic acid. Nitrilase-CLEAs were catalytically active for 3 cycles showcasing 81% conversion, 75.53 g/L product formation and 66.42% yield. The recovered product was confirmed by HPLC, FTIR, LC-MS, and 1H NMR, and displayed > 99% purity.

Preparation of cross-linked enzyme aggregates of lipase from Aspergillus niger: process optimization, characterization, stability, and application for epoxidation of lemongrass oil.

Cross-linked enzyme aggregates (CLEAs) of lipase were prepared after fractional precipitation with 40-50% ammonium sulfate and then cross-linking with glutaraldehyde. The process variables for the preparation of lipase-CLEAs such as glutaraldehyde concentration, cross-linking period, and initial pH of medium were optimized. The optimized conditions for the preparation of lipase-CLEAs were 25 mM/80 min/pH 7.0, and 31.62 mM/90 min/pH 6.0 with one factor at a time approach and numerical optimization with central composite design, respectively. Lipase-CLEAs were characterized by particle size analysis, SEM, and FTIR. Cross-linking not only shifted the optimal pH and temperature from 7.0 to 7.5 and 40-45 to 45-50 °C, but also altered the secondary structure. Lipase-CLEAs showed an increase in Km by 7.70%, and a decrease in Vmax by 16.63%. Lipase-CLEAs presented better thermostability than free lipase as evident from thermal inactivation constants (t1/2, D and Ed value), and thermodynamic parameters (Ed, ΔH°, ΔG°, and ΔS°) in the range of 50-70 °C. Lipase-CLEAs retained more than 65% activity up to four cycles and showed good storage stability for 12 days when stored at 4 ± 2 °C. They were successfully utilized for the epoxidation of lemongrass oil which was confirmed by changes in iodine value, epoxide value, and FTIR spectra.

Characterization of Cross-Linked Enzyme Aggregates of the Y509E Mutant of a Glycoside Hydrolase Family 52 ß-xylosidase from G. stearothermophilus.

Cross-linked enzyme aggregates (CLEAs) of the Y509E mutant of glycoside hydrolase family 52 ß-xylosidase from Geobacillus stearothermophilus with dual activity of ß-xylosidase and xylanase (XynB2Y509E) were prepared. Ammonium sulfate was used as the precipitant agent, and glutaraldehyde as cross-linking agent. The optimum conditions were found to be 90% ammonium sulfate, 12.5 mM glutaraldehyde, 3 h of cross-linking reaction at 25 °C, and pH 8.5. Under these (most effective) conditions, XynB2Y509E-CLEAs retained 92.3% of their original ß-xylosidase activity. Biochemical characterization of both crude and immobilized enzymes demonstrated that the maximum pH and temperature after immobilization remained unchanged (pH 6.5 and 65 °C). Moreover, an improvement in pH stability and thermostability was also found after immobilization. Analysis of kinetic parameters shows that the K m value of XynB2Y509E-CLEAs obtained was slightly higher than that of free XynB2Y509E (1.2 versus 0.9 mM). Interestingly, the xylanase activity developed by the mutation was also conserved after the immobilization process.

Production and Characterization of Cross-Linked Aggregates of Geobacillus thermoleovorans CCR11 Thermoalkaliphilic Recombinant Lipase.

Immobilization of enzymes has many advantages for their application in biotechnological processes. In particular, the cross-linked enzyme aggregates (CLEAs) allow the production of solid biocatalysts with a high enzymatic loading and the advantage of obtaining derivatives with high stability at low cost. The purpose of this study was to produce cross-linked enzymatic aggregates (CLEAs) of LipMatCCR11, a 43 kDa recombinant solvent-tolerant thermoalkaliphilic lipase from Geobacillus thermoleovorans CCR11. LipMatCCR11-CLEAs were prepared using (NH4)2SO4 (40% w/v) as precipitant agent and glutaraldehyde (40 mM) as cross-linker, at pH 9, 20 °C. A U10(56) uniform design was used to optimize CLEA production, varying protein concentration, ammonium sulfate %, pH, glutaraldehyde concentration, temperature, and incubation time. The synthesized CLEAs were also analyzed using scanning electron microscopy (SEM) that showed individual particles of <1 µm grouped to form a superstructure. The cross-linked aggregates showed a maximum mass activity of 7750 U/g at 40 °C and pH 8 and retained more than 20% activity at 100 °C. Greater thermostability, resistance to alkaline conditions and the presence of organic solvents, and better durability during storage were observed for LipMatCCR11-CLEAs in comparison with the soluble enzyme. LipMatCCR11-CLEAs presented good reusability by conserving 40% of their initial activity after 9 cycles of reuse.

Immobilization of Eversa® Transform via CLEA Technology Converts It in a Suitable Biocatalyst for Biolubricant Production Using Waste Cooking Oil.

The performance of the previously optimized magnetic cross-linked enzyme aggregate of Eversa (Eversa-mCLEA) in the enzymatic synthesis of biolubricants by transesterification of waste cooking oil (WCO) with different alcohols has been evaluated. Eversa-mCLEA showed good activities using these alcohols, reaching a transesterification activity with isoamyl alcohol around 10-fold higher than with methanol. Yields of isoamyl fatty acid ester synthesis were similar using WCO or refined oil, confirming that this biocatalyst could be utilized to transform this residue into a valuable product. The effects of WCO/isoamyl alcohol molar ratio and enzyme load on the synthesis of biolubricant were also investigated. A maximum yield of around 90 wt.% was reached after 72 h of reaction using an enzyme load of 12 esterification units/g oil and a WCO/alcohol molar ratio of 1:6 in a solvent-free system. At the same conditions, the liquid Eversa yielded a maximum ester yield of only 34%. This study demonstrated the great changes in the enzyme properties that can be derived from a proper immobilization system. Moreover, it also shows the potential of WCO as a feedstock for the production of isoamyl fatty acid esters, which are potential candidates as biolubricants.

Cross-linked enzyme aggregates of arylamidase from Cupriavidus oxalaticus ICTDB921: process optimization, characterization, and application for mitigation of acrylamide in industrial wastewater.

Acrylamidase produced by Cupriavidus oxalaticus ICTDB921 was recovered directly from the fermentation broth by ammonium sulfate (40-50%) precipitation and then stabilized by cross-linking with glutaraldehyde. The optimum conditions for the preparation of cross-linked enzyme aggregates of acrylamidase (acrylamidase-CLEAs) were using 60 mM glutaraldehyde for 10 min at 35 °C and initial broth pH of 7.0. Acrylamidase-CLEAs were characterized by SDS-PAGE, FTIR, particle size analyzer and SEM. Cross-linking shifted the optimal temperature and pH from 70 to 50 °C and 5-7 to 6-8, respectively. It also altered the secondary structure fractions, pH and thermal stability along with the kinetic constants, Km and Vmax, respectively. A complete degradation of acrylamide ~ 1.75 g/L in industrial wastewater was achieved after 60 min in a batch process under optimum operating conditions, and the kinetics was best represented by Edward model (R2 = 0.70). Acrylamidase-CLEAs retained ~ 40% of its initial activity after three cycles for both pure acrylamide and industrial wastewater, and were stable for 15 days at 4 °C, retaining ~ 25% of its original activity.

Kinetic resolution of racemic naproxen methyl ester by magnetic and non-magnetic cross-linked lipase aggregates.

In this study, the non-magnetic and the magnetic cross-linked enzyme aggregates (CLEAs) from Candida rugosa lipase were synthesized to catalyze the kinetic resolution reaction of naproxen methyl ester (NME). Magnetic iron oxide nanoparticles (MIONPs) were produced through co-precipitation method and their surfaces were modified by silanization reaction. The MIONPs were used as a platform to synthesize the magnetic CLEAs (M-CLEAs). The biocatalysts and MIONPs synthesized were characterized by FTIR spectroscopy and SEM analysis. The kinetic resolution of racemic NME was studied in aqueous buffer solution/isooctane biphasic system to compare the performance of M-CLEAs and CLEAs. The effects of reaction parameters such as temperature, pH, stirring rate on the enantiomeric excess of the substrate (ees%) were investigated in a batch reactor system. The activity recovery of CRL enzyme in CLEAs was higher than M-CLEAs. Compared with M-CLEAs, CLEAs biocatalysts had previously reached ees% values. Although both biocatalysts showed similar cavity structure from SEM analysis, the lower performance of M-CLEAs may be due to the different microenvironments of M-CLEAs from CLEAs. However, the reusability performance of M-CLEAs was higher than that of CLEAs. The optimal reaction conditions for M-CLEAs and CLEAs were found to be 37 °C, pH 7.5, and 300 rpm.

Improving the Yields and Reaction Rate in the Ethanolysis of Soybean Oil by Using Mixtures of Lipase CLEAs.

Due to the heterogeneity of oils, the use of mixtures of lipases with different activity for a large number of glycerol-linked carboxylic acids that compose the substrate has been proposed as a better alternative than the use of one specific lipase preparation in the enzymatic synthesis of biodiesel. In this work, mixtures of lipases from different sources were evaluated in their soluble form in the ethanolysis of soybean oil. A mixture of lipases (50% of each lipase, in activity basis) from porcine pancreas (PPL) and Thermomyces lanuginosus lipase (TLL) gave the highest fatty acid ethyl ester (FAEE) yield (around 20 wt.%), while the individual lipases gave FAEE yields 100 and 5 times lower, respectively. These lipases were immobilized individually by the cross-linked enzyme aggregates (CLEAs) technique, yielding biocatalysts with 89 and 119% of expressed activity, respectively. A mixture of these CLEAs (also 50% of each lipase, in activity basis) gave 90.4 wt.% FAEE yield, while using separately CLEAs of PPL and TLL, the FAEE yields were 84.7 and 75.6 wt.%, respectively, under the same reaction conditions. The mixture of CLEAs could be reused (five cycles of 6 h) in the ethanolysis of soybean oil in a vortex flow-type reactor yielding an FAEE yield higher than 80% of that of the first batch.

Cross-linked α-galactosidase aggregates: optimization, characterization and application in the hydrolysis of raffinose-type oligosaccharides in soymilk.

BACKGROUND: Cross-linked enzyme aggregates (CLEAs) of α-galactosidase, partially purified from maize (Zea mays) flour, were prepared. The impact of various parameters on enzyme activity was examined to optimize the immobilization procedure. Biochemical characterization of the free and immobilized enzyme was carried out. Stability (thermal, pH, storage and operational stability) and reusability tests were performed. The potential use of the free enzyme and the CLEAs in hydrolysis processes of raffinose-type oligosaccharides present in soymilk was investigated. RESULTS: α-galactosidase CLEAs were prepared with 47% activity recovery under optimum conditions [1:5 (v/v) enzyme solution:saturated ammonium sulfate solution ratio; 7.5 mg protein and 0.1% (v/v) glutaraldehyde, 6 h, 4 °C, 150 rpm]. α-galactosidase CLEAs exhibited increased stability in comparison to the free enzyme. The CLEAs and the free enzyme showed a maximum activity at 40°C and their optimal pH values were5.5 and 6.0, respectively. Kinetic constants (KM , Vmax and kcat ) were calculated for the free enzyme and the CLEAs in the presence of p-nitrophenyl-α-d-galactopyranoside, stachyose, melibiose and raffinose. The effect of various chemicals and sugars on enzyme activity showed that both enzyme forms were significantly inhibited by HgCl2 and galactose. The CLEAs hydrolyzed 85% of raffinose and 96% of stachyose. CONCLUSION: The α-galactosidase CLEAs, with their satisfactory enzymatic characteristics, have much potential for use in the food and feed industry. © 2019 Society of Chemical Industry.

Adding an appropriate amino acid during crosslinking results in more stable crosslinked enzyme aggregates.

Carrier free immobilization, especially crosslinked enzyme aggregates (CLEAs), has become an important design for biocatalysis in several areas. Adding amino acids during formation of CLEAs was found to give biocatalysts more stable at 55 °C and in the presence of 60% acetonitrile. The half-lives of CLEAs prepared with and without Arg addition were 21 and 15 h (subtilisin) and 4 and 1.6 h (α-chymotrypsin) at 55 °C, respectively. The corresponding half-lives during acetonitrile presence were 4.1 and 3.0 h (subtilisin) and 39 and 22 min (α-chymotrypsin), respectively. CLEAs made with Arg had higher percentages of alpha helix. CLEAs made by adding Lys, Ala, or Asp also were more stable. In the case of Thermomyces lanuginosus lipase (TLL), CLEA with Ala was even more stable than CLEA with Arg. The addition of a suitable amino acid, thus, enhances CLEA stabilities. The results are discussed in the light of earlier results on chemical modification of proteins and the observation that the Arg/Lys ratio is invariably high in the case of enzymes from thermophiles.

Aroma Release in Wine Using Co-Immobilized Enzyme Aggregates.

Aroma is a remarkable factor of quality and consumer preference in wine, representing a distinctive feature of the product. Most aromatic compounds in varietals are in the form of glycosidic precursors, which are constituted by a volatile aglycone moiety linked to a glucose residue by an O-glycosidic bond; glucose is often linked to another sugar (arabinose, rhamnose or apiose). The use of soluble ß-glycosidases for aroma liberation implies the addition of a precipitating agent to remove it from the product and precludes its reuse after one batch. An attractive option from a technological perspective that will aid in removing such constraints is the use of immobilized glycosidases. Immobilization by aggregation and crosslinking is a simple strategy producing enzyme catalysts of very high specific activity, being an attractive option to conventional immobilization to solid inert supports. The purpose of this work was the evaluation of co-immobilized ß-glycosidases crosslinked aggregates produced from the commercial preparation AR2000, which contains the enzymes involved in the release of aromatic terpenes in Muscat wine (α-l-arabinofuranosidase and ß-d-glucopyranosidase). To do so, experiments were conducted with co-immobilized crosslinked enzyme aggregates (combi-CLEAs), and with the soluble enzymes, using an experiment without enzyme addition as control. Stability of the enzymes at the conditions of winemaking was assessed and the volatiles composition of wine was determined by SPE-GC-MS. Stability of enzymes in combi-CLEAs was much higher than in soluble form, 80% of the initial activity remaining after 60 days in contact with the wine; at the same conditions, the soluble enzymes had lost 80% of their initial activities after 20 days. Such higher stabilities will allow prolonged use of the enzyme catalyst reducing its impact in the cost of winemaking. Wine treated with combi-CLEAs was the one exhibiting the highest concentration of total terpenes (18% higher than the control) and the highest concentrations of linalool (20% higher), nerol (20% higher) and geraniol (100% higher), which are the most important terpenes in determining Muscat typicity. Co-immobilized enzymes were highly stable at winemaking conditions, so their reutilization is possible and technologically attractive by reducing the impact of enzyme cost on winemaking cost.

Improvement of combined cross-linked enzyme aggregates of cyclodextrin glucanotransferase and maltogenic amylase by functionalization of cross-linker for maltooligosaccharides synthesis.

Combined cross-linked enzyme aggregates of cyclodextrin glucanotransferase (CGTase) and maltogenic amylase (Mag1) from Bacillus lehensis G1 (Combi-CLEAs-CM) were successfully developed to synthesis maltooligosaccharides (MOS). Yet, the poor cross-linking performance between chitosan (cross-linker) and enzymes resulting low activity recovery and catalytic efficiency. In this study, we proposed the functionalization of cross-linkers with the integration of computational analysis to study the influences of different functional group on cross-linkers in combi-CLEAs development. From in-silico analysis, O-carboxymethyl chitosan (OCMCS) with the highest binding affinity toward both enzymes was chosen and showed alignment with the experimental result, in which OCMCS was synthesized as cross-linker to develop improved activity recovery of Combi-CLEAs-CM-ocmcs (74 %). The thermal stability and deactivation energy (205.86 kJ/mol) of Combi-CLEAs-CM-ocmcs were found to be higher than Combi-CLEAs-CM (192.59 kJ/mol). The introduction of longer side chain of carboxymethyl group led to a more flexible structure of Combi-CLEAs-CM-ocmcs. This alteration significantly reduced the Km value of Combi-CLEAs-CM-ocmcs by about 3.64-fold and resulted in a greater Kcat/Km (3.63-fold higher) as compared to Combi-CLEAs-CM. Moreover, Combi-CLEAs-CM-ocmcs improved the reusability with retained >50 % of activity while Combi-CLEAs-CM only 36.18 % after five cycles. Finally, maximum MOS production (777.46 mg/g) was obtained by Combi-CLEAs-CM-ocmcs after optimization using response surface methodology.

An Overview of Crosslinked Enzyme Aggregates: Concept of Development and Trends of Applications.

Enzymes are commonly used as biocatalysts for various biological and chemical processes in industrial applications. However, their limited operational stability, catalytic efficiency, poor reusability, and high-cost hamper further industrial usage. Thus, crosslinked enzyme aggregates (CLEAs) are developed as a better enzyme immobilization tool to extend the enzymes' operational stability. This immobilization method is appealing because it is simpler due to the absence of ballast and permits the collective use of crude enzyme cocktails. CLEAs, so far, have been successfully developed using a variety of enzymes, viz., hydrolases, proteases, amidases, lipases, esterases, and oxidoreductase. Recent years have seen the emergence of novel strategies for preparing better CLEAs, which include the combi- and multi-CLEAs, magnetics CLEAs, and porous CLEAs for various industrial applications, viz., laundry detergents, organic synthesis, food industries, pharmaceutical applications, oils, and biodiesel production. To better understand the different strategies for CLEAs' development, this review explores these strategies and highlights the relevant concerns in designing innovative CLEAs. This article also details the challenges faced during CLEAs preparation and solutions for overcoming them. Finally, the trending strategies to improve the preparation of CLEAs alongside their industrial application trends are also discussed.

Enzyme immobilization technology as a tool to innovate in the production of biofuels: A special review of the Cross-Linked Enzyme Aggregates (CLEAs) strategy.

This review emphasizes the crucial role of enzyme immobilization technology in advancing the production of two main biofuels, ethanol and biodiesel, with a specific focus on the Cross-linked Enzyme Aggregates (CLEAs) strategy. This method of immobilization has gained attention due to its simplicity and affordability, as it does not initially require a solid support. CLEAs synthesis protocol includes two steps: enzyme precipitation and cross-linking of aggregates using bifunctional agents. We conducted a thorough search for papers detailing the synthesis of CLEAs utilizing amylases, cellulases, and hemicellulases. These key enzymes are involved in breaking down starch or lignocellulosic materials to produce ethanol, both in first and second-generation processes. CLEAs of lipases were included as these enzymes play a crucial role in the enzymatic process of biodiesel production. However, when dealing with large or diverse substrates such as lignocellulosic materials for ethanol production and oils/fats for biodiesel production, the use of individual enzymes may not be the most efficient method. Instead, a system that utilizes a blend of enzymes may prove to be more effective. To innovate in the production of biofuels (ethanol and biodiesel), enzyme co-immobilization using different enzyme species to produce Combi-CLEAs is a promising trend.

Combined cross-linked enzyme aggregates of cyclodextrin glucanotransferase and maltogenic amylase from Bacillus lehensis G1 for maltooligosaccharides synthesis.

Maltooligosaccharides (MOS) are functional oligosaccharides that can be synthesized through enzymatic cascade reaction between cyclodextrin glucanotransferase (CGTase) and maltogenic amylase (Mag1) from Bacillus lehensis G1. To address the problems of low operational stability and non-reusability of free enzymes, both enzymes were co-immobilized as combined cross-linked enzyme aggregates (Combi-CLEAs-CM) with incorporation of bovine serum albumin (BSA) and Tween 80 (Combi-CLEAs-CM-add). Combi-CLEAs-CM and Combi-CLEAs-CM-add showed activity recoveries of 54.12 % and 69.44 %, respectively after optimization. Combi-CLEAs-CM-add showed higher thermal stability at higher temperatures (40 °C) with longer half-life (46.20 min) as compared to those of free enzymes (36.67 min) and Combi-CLEAs-CM (41.51 min). Both combi-CLEAs also exhibited higher pH stability over pH 5 to pH 9, and displayed excellent reusability with >50 % of initial activity retained after four cycles. The reduction in Km value of about 22.80 % and 1.76-fold increase in starch hydrolysis in comparison to Combi-CLEAs-CM attested the improvement of enzyme-substrate interaction by Tween 80 and pores formation by BSA in Combi-CLEAs-CM-add. The improved product specificity of Combi-CLEAs-CM-add also produced the highest yield of MOS (492 mg/g) after 3 h. Therefore, Combi-CLEAs-CM-add with ease of preparation, excellent reusability and high operational stability is believed to be highly efficacious biocatalyst for MOS production.

Bio-imprinted magnetic cross-linked polyphenol oxidase aggregates for enhanced synthesis of L-dopa, a neurodegenerative therapeutic drug.

Bio-imprinted magnetic cross-linked enzyme aggregates (i-m-CLEAs) of polyphenol oxidase (PPO) obtained from potato peels were prepared using amino-functionalized magnetic nanoparticles. Bio-imprinting is being used to improve the catalytic efficiency and conformational stability of enzymes. For bio-imprinting, PPO was incubated with different imprint/template molecules (catechol, 4-methyl catechol and l-3,4-dihydroxy phenylalanine) before cross-linking with glutaraldehyde. CLEAs imprinted with 4-methyl catechol showed maximum activity as compared with non-bio-imprinted magnetic CLEAs (m-CLEAs). They were further characterized by scanning electron microscopy and confocal microscopy. In bio-imprinted m-CLEAs, half-life (t1/2) of PPO significantly improved (364.74 min) as compared to free PPO (43.58 min) and non-bio-imprinted m-CLEAs (266.54 min). Bio-imprinted m-CLEAs showed excellent thermal and storage stability as well as reusability. The CLEAs preparation were used for the synthesis of l-3,4-dihydroxyphenylalanine (L-dopa, a therapeutic drug to treat neurodegenerative disorder) and a remarkable increase in L-dopa yield (23.5-fold) was obtained as compared to free enzyme. A cost effective and reusable method has been described for the production of L-dopa.

Lipase immobilization via cross-linked enzyme aggregates: Problems and prospects - A review.

In this review we have focused on the preparation of cross-linked enzyme aggregates (CLEAs) from lipases, as these are among the most used enzyme in bioprocesses. This immobilization method is considered very attractive due to preparation simplicity, non-use of supports and the possibility of using crude enzyme extracts. CLEAs provide lipase stabilization under extreme temperature or pH conditions or in the presence of organic solvents, in addition to preventing enzyme leaching in aqueous medium. However, it presents some problems in the preparation and limitations in their use. The problems in preparation refer mainly to the crosslinking step, and may be solved using an aminated feeder. The problems in handling have been tackled designing magnetic-CLEAs or trapping the CLEAs in particles with better mechanical properties, the substrate diffusion problems has been reduced by producing more porous-CLEAs, etc. The enzyme co-immobilization using combi-CLEAs is also a new tendency. Therefore, this review explores the CLEAs methodology aimed at lipase immobilization and its applications.