Synthesis of a novel magnetic calcium-rich biochar nanocomposite for efficient removal of phosphate from aqueous solution.

Phosphorus (P) scarcity and eutrophication have triggered the development of new materials for P recovery. In this work, a novel magnetic calcium-rich biochar nanocomposite (MCRB) was prepared through co-precipitation of crab shell derived biochar, Fe2+ and Fe3+. Characteristics of the material demonstrated that the MCRB was rich in calcite and that the Fe3O4 NPs with a diameter range of 18-22 nanometers were uniformly adhered on the biochar surface by strong ether linking (C-O-Fe). Batch tests demonstrated that the removal of P was pH dependent with an optimal pH of 3-7. The MCRB exhibited a superior P removal performance, with a maximum removal capacity of 105.6 mg g-1, which was even higher than the majority lanthanum containing compounds. Study of the removal mechanisms revealed that the P removal by MCRB involved the formation of hydroxyapatite (HAP-Ca5(PO4)3OH), electrostatic attraction and ligand exchange. The recyclability test demonstrated that a certain level (approximately 60%) was still maintained even after the six adsorption-desorption process, suggesting that MCRB is a promising material for P removal from wastewater.

Simultaneous removal of phosphate and tetracycline using LaFeO3 functionalised magnetic biochar by obtained ultrasound-assisted sol-gel pyrolysis: Mechanisms and characterisation.

Excessive phosphate and tetracycline (TC) contaminants pose a serious risk to human health and the ecological environment. As such exploring the simultaneous adsorption of phosphate and TC is garnering increasing attention. In this study, an efficient lanthanum ferrate magnetic biochar (FLBC) was synthesised from crab shells using an ultrasound-assisted sol-gel method to study its performance and mechanisms for phosphate and TC adsorption in aqueous solutions in mono/bis systems. According to the Langmuir model, the developed exhibited a maximum adsorption capacity of 65.62 mg/g for phosphate and 234.1 mg/g for TC (pH:7.0 ± 0.1, and 25 °C). Further, it exhibited high resistance to interference and pH suitability. In practical swine wastewater applications, whereby the concentrations of phosphate and TC are 37 and 19.97 mg/L, respectively, the proposed material demonstrated excellent performance. In addition, electrostatic adsorption, chemical precipitation and ligand exchange were noted to be the main mechanisms for phosphate adsorption by FLBC, whereas hydrogen bonding and π-π interaction were the main adsorption mechanisms for TC adsorption. Therefore, this study successfully prepared a novel and efficient adsorbent for phosphate and TC.

Bioprocess development as a sustainable platform for eco-friendly alkaline phosphatase production: an approach towards crab shells waste management.

BACKGROUND: There are substantial environmental and health risks associated with the seafood industry's waste of crab shells. In light of these facts, shellfish waste management is critical for environmental protection against hazardous waste produced from the processing industries. Undoubtedly, improved green production strategies, which are based on the notion of "Green Chemistry," are receiving a lot of attention. Therefore, this investigation shed light on green remediation of the potential hazardous crab shell waste for eco-friendly production of bacterial alkaline phosphatase (ALP) through bioprocessing development strategies. RESULTS: It was discovered that by utilizing sequential statistical experimental designs, commencing with Plackett-Burman design and ending with spherical central composite design, and then followed by pH-uncontrolled cultivation conditions in a 7 L bench-top bioreactor, an innovative medium formulation could be developed that boosted ALP production from Bacillus licheniformis strain ALP3 to 212 U L-1. The highest yield of ALP was obtained after 22 h of incubation time with yield coefficient Yp/s of 795 U g-1, which was 4.35-fold higher than those obtained in the shake-flask system. ALP activity has a substantial impact on the volatilization of crab shell particles, as shown by the results of several analytical techniques such as atomic absorption spectrometry, TGA, DSC, EDS, FTIR, and XRD. CONCLUSIONS: We highlighted in the current study that the biovalorization of crab shell waste and the production of cost-effective ALP were being combined and that this was accomplished via the use of a new and innovative medium formulation design for seafood waste management as well as scaling up production of ALP on the bench-top scale.

Removal of copper from sulfate solutions using biochar derived from crab processing by-product.

Increasing metal demand is accelerating the mining and processing of minerals, however to ensure sustainable growth innovative approaches are required to better manage associated effluents. Biochar from the fast pyrolysis of residues from fishery and forestry operations has been studied as a low-cost, environmentally and economically friendly method for treating mine tailings and processing effluents. However, the bulk of the studies focus on terrestrial biomass (e.g. wood) and do not include potential inhibition/enhancement of adsorption due to pH controlling compounds. In this work biochar generated from snow crab (Chionoecetes Opilio) processing was studied as an adsorbent for copper solutions containing sulfate (a key compound in sulfide ore mining waters) with the objective of assessing adsorption capacity and the impact of sulfate on copper adsorption. The biochar, a porous structure comprised of calcite (CaCO3), was alkaline and has a negative zeta potential under neutral and basic conditions. The crab biochar removed over 99% of Cu2+ from a 100 mg/L solution (sourced as CuSO4) at a dosage of 5 g/L, which was higher than lignocellulosic biochar at the same biochar dosage. While metal adsorption can often be impacted at acidic conditions, Cu2+ adsorption was not impacted by initial acidic pH due to the biochar's buffering capacity. The Pseudo-Second Order (PSO) model fit the adsorption rate with maximum adsorption achieved in approximately 2 h. The maximum adsorption isotherm capacity was 184.8 ± 10.2 mg/g for Cu2+, much higher than existing commercial activated carbons and previously studied lignocellulosic biochars and followed the Freundlich isotherm. The adsorption mechanism responsible for removal of Cu2+ was found to be precipitation, in the form of the mineral posnjakite (Cu4[(OH)6SO4]·H2O). These results indicate for the first time that crab-based biochars are capable of adsorbing large quantities of Cu2+ from sulfate-rich solution, while also buffering solution pH, demonstrating promise as an acid mine drainage treatment for removal of harmful metals and reduction of acidity.

Mechano-Enzymatic Degradation of the Chitin from Crustacea Shells for Efficient Production of N-acetylglucosamine (GlcNAc).

Chitin, the second richest polymer in nature, is composed of the monomer N-acetylglucosamine (GlcNAc), which has numerous functions and is widely applied in the medical, food, and chemical industries. However, due to the highly crystalline configuration and low accessibility in water of the chitin resources, such as shrimp and crab shells, the chitin is difficult utilize, and the traditional chemical method causes serious environment pollution and a waste of resources. In the present study, three genes encoding chitinolytic enzymes, including the N-acetylglucosaminidase from Ostrinia furnacalis (OfHex1), endo-chitinase from Trichoderma viride (TvChi1), and multifunctional chitinase from Chitinolyticbacter meiyuanensis (CmChi1), were expressed in the Pichia pastoris system, and the positive transformants with multiple copies were isolated by the PTVA (post-transformational vector amplification) method, respectively. The three recombinants OfHex1, TvChi1, and CmChi1 were induced by methanol and purified by the chitin affinity adsorption method. The purified recombinants OfHex1 and TvChi1 were characterized, and they were further used together for degrading chitin from shrimp and crab shells to produce GlcNAc through liquid-assisted grinding (LAG) under a water-less condition. The substrate chitin concentration reached up to 300 g/L, and the highest yield of the product GlcNAc reached up to 61.3 g/L using the mechano-enzymatic method. A yield rate of up to 102.2 g GlcNAc per 1 g enzyme was obtained.

Crab shell amendments enhance the abundance and diversity of key microbial groups in sulfate-reducing columns treating acid mine drainage.

Substrate amendments composed of crab shell (CS) waste materials have been shown to significantly improve the longevity and performance of acid mine drainage (AMD) treatment systems containing spent mushroom compost (SMC), yet the development of key microbial populations within these systems has not been investigated. To better understand the effects of CS on microbial dynamics in these systems, clone libraries and real-time quantitative PCR (qPCR) were performed on materials from a laboratory-scale AMD treatment system containing SMC and 0 to 100% CS substrate after receiving a continuous flow of AMD for 148 days (428 pore volumes). The proportion of CS in the substrate positively correlated with the diversity of sulfate-reducing bacteria (SRB) and archaeal clones, but negatively correlated with fungal diversity. CS also impacted microbial community structure, as revealed in Unifrac significance and principal coordinate analysis tests. The column containing 100% CS substrate supported 7 different genera of SRB-the most ever observed in an AMD treatment system. Moreover, the copy numbers of functional genes representing fermenters, sulfate reducers, and chitin degraders increased with increasing proportions of CS. These observations agree well with the chemical performance data, further validating that by supporting more abundant key microbial groups, chitinous substrates may provide benefits for improving both the longevity and performance of AMD treatment systems, and may provide similar benefits for the treatment of other environmental contaminants that are amenable to anaerobic bioremediation.Key points• Crab shell improves the longevity and performance of acid mine drainage treatment.• The diversity of sulfate-reducing bacteria is enhanced with crab shell amendments.• Crab shell supports more abundant key microbial groups than spent mushroom compost.

A sensitive dispersive micro solid-phase extraction coupled with high performance liquid chromatography for determination of three flavonoids in complex matrics by using crab shell as a sorbent.

A sensitive dispersive micro solid-phase extraction coupled with HPLC has been developed for preconcentration and determination of three flavonoids (quercetin, kaempferol, and isorhamnetin) in complex matrix samples. Parameters that affect extraction efficiency have been optimized. The optimal extraction conditions are using 2 µg/mL of crab shell as the sorbent, extraction for 2 min at pH 7, and then eluting with 100 µL of methanol. As a result, the method shows good linearity (R > 0.9994), low LODs (even 0.08 ng/ml) and satisfactory recovery in real honey and rat urine samples. As an eco-friendly biomaterial, crab shell powder is used as sorbent in pretreatment of flavonoids, and its adsorption mechanism has been investigated for the first time. Compared with the other reported methods, the proposed strategy is time-saving, eco-friendly, and highly sensitive using HPLC (even achieving MS grade sensitivity).

Carbon Dots Green Synthesis for Ultra-Trace Determination of Ceftriaxone Using Response Surface Methodology.

The present study sought to develop a facile and green synthetic approach for producing fluorescent carbon dots (CDs) from a natural biomass using aqueous extraction of carbonized blue crab shell. Spherical carbon dots (6.00 ± 3.0 nm) exhibited an extended emission range with excellent quantum yield (14.5 ± 3.5%). In order to measure ceftriaxone, we offered a simple and sensitive method, based on fluorescence quenching of carbon dots in plasma and water with recovery values of 94.5-104.1%. Furthermore, with usage of central composite design (CCD) based response surface methodology (RSM); we optimized the effect of different factors. In addition, ANOVA evaluated the accuracy and suitability of quadratic model. Under optimal conditions, fluorescence quenching revealed a sensitive response in the concentration range of 20-1000 nM with the limit of detection 9.0 nM for ceftriaxone. Finally, carbon dots-based fluorescence quenching procedure was able to quantify ceftriaxone in plasma, as well as mineral and tap water. Spiked samples achieved satisfactory efficiencies.

Amperometric sensing of ascorbic acid by using a glassy carbon electrode modified with mesoporous carbon nanorods.

Mesoporous carbon nanorods (MCNRs) were prepared from honey as the carbon source and by using crab (Brachyuran) shells as the hard template. The unique nanostructure of the MCNRs with their uniform mesoporous size, abundant defective sites and numerous oxygen-functional groups was characterized by nitrogen adsorption-desorption isotherms, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. Cyclic voltammograms of a glassy carbon electrode (GCE) modified with MCNRs revel a higher peak current density and lower peak potential (-0.03 V vs. Ag/AgCl) for ascorbic acid (AA) electrooxidation compared to a conventional GCE and a carbon nanotube-modified GCE. Figures of merit for this sensor include (a) a wide linear range (10-2770 µM), (b) high electrochemical sensitivity (216.91 µA mM-1 cm-2) and (c) a low detection limit (2.3 µM). These compare favorably to the respective data for a CNT-modified GCE (50-2150 µM, 5.20 µA mM-1 cm-2 and 26.8 µM) and a plain GCE (100-2000 µM, 0.58 µA mM-1 cm-2 and 54.6 µM). The modified GCE was successfully applied to the determination of AA in (spiked) real samples including an injection, soft drinks and fresh lemon juice. Therefore, the new sensor can be considered as an affordable tool for electrochemical sensing of AA in real samples. Graphical abstract Mesoporous carbon nanorods (MCNRs) were prepared by using honey as the carbon source and crab shells as the hard template. The MCNRs modified a glassy carbon electrode (MCNRs/GCE) was used for the ascorbic acid (AA) detection by amperometry.

Calcium-rich biochar from the pyrolysis of crab shell for phosphorus removal.

Calcium-rich biochars (CRB) prepared through pyrolysis of crab shell at various temperatures were characterized for physicochemical properties and P removal potential. Elemental analysis showed that CRB was rich in calcium (22.91%-36.14%), while poor in carbon (25.21%-9.08%). FTIR, XRD and TG analyses showed that calcite-based CRB was prepared at temperature ≤600 °C, while lime-based CRB was prepared at temperature ≥700 °C. Phosphorus removal experiment showed that P removal efficiencies in 80 mg P/L phosphate solution and biogas effluent ranged from 26% to 11%, respectively, to about 100% and 63%, respectively, depending on the pyrolysis temperature of the resulting biochar. Specifically, compared to common used CaCO3 and Ca(OH)2, P removal potential of calcite-based CRB was much higher than that of CaCO3; while that of lime-based CRB was close to that of Ca(OH)2. These results suggested that CRB was competent for P removal/recovery from wastewater.

Protein/CaCO3/Chitin Nanofiber Complex Prepared from Crab Shells by Simple Mechanical Treatment and Its Effect on Plant Growth.

A protein/CaCO3/chitin nanofiber complex was prepared from crab shells by a simple mechanical treatment with a high-pressure water-jet (HPWJ) system. The preparation process did not involve chemical treatments, such as removal of protein and calcium carbonate with sodium hydroxide and hydrochloric acid, respectively. Thus, it was economically and environmentally friendly. The nanofibers obtained had uniform width and dispersed homogeneously in water. Nanofibers were characterized in morphology, transparency, and viscosity. Results indicated that the shell was mostly disintegrated into nanofibers at above five cycles of the HPWJ system. The chemical structure of the nanofiber was maintained even after extensive mechanical treatments. Subsequently, the nanofiber complex was found to improve the growth of tomatoes in a hydroponics system, suggesting the mechanical treatments efficiently released minerals into the system. The homogeneous dispersion of the nanofiber complex enabled easier application as a fertilizer compared to the crab shell flakes.

Pathologic mandibular fracture after biting crab shells following ramal bone graft.

The mandibular ramus is considered an appropriate choice for reconstruction of maxillofacial defects because of sufficient amounts of material and fewer donor site complications. Although bone harvesting from the mandibular ramus has many advantages, in rare cases it can result in pathologic fracture of the mandible. Here, we present a case of 59-year-old man who suffered a pathologic mandible fracture related to biting hard foods, such as crab shells, after a sinus bone lifting with ramal bone graft procedure performed 2 weeks prior. He underwent closed reduction by intermaxillary fixation with an arch bar over the course of 4 weeks. Three months later, the patients had a stable occlusion with normal mouth opening and sensation. To prevent this complication, the osteotomy should be performed in such a way that it is not too vertical during ramal bone harvesting. Furthermore, we wish to emphasize the importance of patients being instructed to avoid chewing hard foods for at least 4 weeks after ramal bone harvesting.

Enzymatic properties of chitinase-producing antagonistic bacterium Paenibacillus chitinolyticus with various substrates.

Various chitin substrates were used to investigate the properties of enzymes produced from the chitinase-producing bacterium Paenibacillus chitinolyticus MP-306 against phytopathogens. The MP-306 bacterium was incubated in nine culture media [crab shell powder chitin (CRS), chitin-protein complex powder (CPC), carboxymethyl-chitin powder (CMC), yeast extract only (YE), LB (Trypton, NaCl, and yeast extract), GT (Trypton, NaCl, and glucose), crab shell colloidal chitin (CSC), squid pen powder chitin (SPC), and cicada slough powder chitin (CSP)] at 30 °C for 3 days. Chitinase isozymes in CPC medium were expressed strongly as CN1, CN2, CN3, CN4, CN5, and CN6 bands on native-PAGE gels. Chitinase isozymes in CPC and CMC medium were expressed as 13 bands (CS1-CS13) on SDS-PAGE gels. Chitinase isozymes were expressed strongly on SDS-PAGE gels as two bands (CS6 and CS8) on YE and LB medium and 13 bands (CS1-CS13) on SPC medium. In crude enzyme, chitinase isozymes at pH 7 and pH 9 in chitin media appeared strongly on SDS-PAGE gels. Partial purified enzyme indicated high stability of enzyme activity at various temperatures and pHs in chitin medium, while these enzymes indicated low activity staining of enzyme on electrophoresis gels at various temperatures and pHs condition of chitin medium.

Chitin/calcite composite extracted from shell waste as a low-cost adsorbent for removal of tetracycline and ciprofloxacin: Effects and mechanisms.

Recently, water contamination caused by the misuse of antibiotics has become a growing concern. In this study, an economical chitin/calcite composite (CCA) was extracted from crab shell waste, and the effects and mechanisms of its removal of ciprofloxacin (CIP) and tetracycline (TC) from aqueous solution were investigated. The functional groups of chitin and the metal phase of calcite gave CCA the ability to remove antibiotics. Experiments on kinetics, isothermal adsorption, thermodynamics, co-removal, and reusability were conducted to systematically explore the adsorption performances of CCA toward antibiotics. The pseudo-second-order (FSO) and Langmuir models suited the data obtained from experiments best and displayed a good fit for the chemisorption and a certain homogeneity of adsorption sites. At 25 °C, the maximum adsorption capacities (Qmax) toward CIP and TC were 228.86 and 150.76 mg g-1, respectively. The adsorption mechanisms of CCA with TC and CIP are pH dependent since pH can affect the surface charge of CCA and the form in which CIP and TC are existing. The X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) demonstrated that the keto-O and carboxyl groups of CIP and the carbonyl, hydroxyl, and amido groups of TC could be responsible for the binding with the calcite and the functional groups of chitin through surface complexation, cation bridge and hydrogen bonding.

Mesoporous Activated Biochar from Crab Shell with Enhanced Adsorption Performance for Tetracycline.

In this study, three mesoporous-activated crab shell biochars were prepared by carbonation and chemical activation with KOH (K-CSB), H3PO4 (P-CSB), and KMnO4 (M-CSB) to evaluate their tetracycline (TC) adsorption capacities. Characterization by SEM and a porosity analysis revealed that the K-CSB, P-CSB, and M-CSB possessed a puffy, mesoporous structure, with K-CSB exhibiting a larger specific surface area (1738 m2/g). FT-IR analysis revealed that abundant, surface ox-containing functional groups possessed by K-CSB, P-CSB, and M-CSB, such as -OH, C-O, and C=O, enhanced adsorption for TC, thereby enhancing their adsorption efficiency for TC. The maximum TC adsorption capacities of the K-CSB, P-CSB, and M-CSB were 380.92, 331.53, and 281.38 mg/g, respectively. The adsorption isotherms and kinetics data of the three TC adsorbents fit the Langmuir and pseudo-second-order model. The adsorption mechanism involved aperture filling, hydrogen bonding, electrostatic action, π-π EDA action, and complexation. As a low-cost and highly effective adsorbent for antibiotic wastewater treatment, activated crab shell biochar has enormous application potential.

Sustainable wastewater purification with crab shell-derived biochar: Advanced machine learning modeling & experimental analysis.

Detoxifying ecologically persistent dyes is vital for environmental and human well-being. Herein, crabshell waste is transformed into porous carbon (CB900) through pyrolysis, achieving a remarkable removal rate of 90.5% (CR-RR) and adsorption capacity (∼256.36 mg g-1, qCR). Employing XGBoost modeling, with a robust R2 âˆ¼0.996, proved its superiority over others in predicting CR adsorption. PSO-XGB optimization led to an optimal configuration: 0.051 g adsorbent, 460.56 mg L-1 CR concentration, pH 3.16, and a 94.01 min contact time, resulting in 68.39% CR-RR and 822.15 mg g-1 qCR, simultaneously; sensitivity analysis unveiled the pivotal role of pH and adsorbent dose. CB900 exhibited physical, spontaneous, endothermic following both Langmuir and Freundlich isotherms. Remarkably, CB900 effectively eliminated various contaminants, including chromium and sulfasalazine antibiotic. Pilot-scale CB900 production cost via pyrolysis was $8.5/kg, a fraction of commercial powdered activated carbon, underscoring its economic viability and potential as a sustainable solution for the elimination of toxic contaminants from aqueous environments.

A Novel Nanoporous Adsorbent for Pesticides Obtained from Biogenic Calcium Carbonate Derived from Waste Crab Shells.

A novel nanoporous adsorbent was obtained through the thermal treatment and chemical wash of the wasted crab shells (BC1) and characterized by various techniques. The structure of BC1 at the end of the treatments comprised a mixture of calcite and amorphous CaCO3, as evidenced by X-ray diffraction and Fourier transform infrared absorption. The BET surface area, BET pore volume, and pore diameter were 250.33 m2 g-1, 0.4 cm3 g-1, and <70 nm, respectively. The point of zero charge of BC1 was determined to be around pH 9. The prepared adsorbent was tested for its adsorption efficacy towards the neonicotinoid pesticide acetamiprid. The influence of pH (2-10), temperature (20-45 °C), adsorbent dose (0.2-1.2 g L-1), contact time (5-60 min), and initial pesticide concentration (10-60 mg L-1) on the adsorption process of acetamiprid on BC1 was studied. The adsorption capacity of BC1 was 17.8 mg g-1 under optimum conditions (i.e., 20 mg L-1 initial acetamiprid concentration, pH 8, 1 g L-1 adsorbent dose, 25 °C, and 15 min contact time). The equilibrium data obtained from the adsorption experiment fitted well with the Langmuir isotherm model. We developed an effective nanoporous adsorbent for the recycling of crab shells which can be applied on site with minimal laboratory infrastructure according to local needs.

Use of Chitosan from Southern King Crab to Develop Films Functionalized with RGD Peptides for Potential Tissue Engineering Applications.

Southern King Crab (SKC) represents an important fishery resource that has the potential to be a natural source of chitosan (CS) production. In tissue engineering, CS is very useful to generate biomaterials. However, CS has a lack of signaling molecules that facilitate cell-substrate interaction. Therefore, RGD (arginine-glycine-aspartic acid) peptides corresponding to the main integrin recognition site in extracellular matrix proteins have been used to improve the CS surface. The aim of this study was to evaluate in vitro cell adhesion and proliferation of CS films synthesized from SKC shell wastes functionalized with RGD peptides. The FTIR spectrum of CS isolated from SKC shells (SKC-CS) was comparable to commercial CS. Thermal properties of films showed similar endothermic peaks at 53.4 and 53.0 °C in commercial CS and SKC-CS, respectively. The purification and molecular masses of the synthesized RGD peptides were confirmed using HPLC and ESI-MS mass spectrometry, respectively. Mouse embryonic fibroblast cells showed higher adhesion on SKC-CS (1% w/v) film when it was functionalized with linear RGD peptides. In contrast, a cyclic RGD peptide showed similar adhesion to control peptide (RDG), but the highest cell proliferation was after 48 h of culture. This study shows that functionalization of SKC-CS films with linear or cyclic RGD peptides are useful to improve effects on cell adhesion or cell proliferation. Furthermore, our work contributes to knowledge of a new source of CS to synthesize constructs for tissue engineering applications.

Recycling of waste crab shells into reinforced poly (lactic acid) biocomposites for 3D printing.

To promote natural waste resource utilization, a novel biocomposite, composed of waste crab shells and poly (lactic acid) matrix, was developed by combining chemical treatment and 3D printing. A crab shell powder (ISCSP) with an abundant porous structure and a high specific surface area was obtained by treatment with hydrochloric acid and sodium hydroxide. Importantly, under the optimal printing parameters determined by the finite element analysis, test samples, and porous bones were successfully printed using CSP/PLA composites by a commercial fused deposition modeling (FDM) 3D printer. The morphology, mechanical and thermal properties, antibacterial properties, and biocompatibility of the CSP/PLA composites were then assessed. Our results revealed that the tensile strength and flexural strength of the ISCSP/PLA composites reached 58.71 and 90.11 MPa, which were 28.6 % and 28.8 % higher than that of pure PLA, respectively. The glass transition and melting temperatures of the composites remained similar to those of pure PLA. Interestingly, the addition of CSP increased PLA crystallinity, which could be attributed to the nucleation effect of CSP in the system. The antibacterial activity of the PLA-1.5ESCSP composite samples against Escherichia coli (E. coli) was greater than 99 %. More importantly, the live/dead assay showed that the CSP/PLA composites possessed excellent biocompatibility. Therefore, the developed CSP/PLA biocomposites are potential feedstocks for 3D printing in bone tissue engineering and may be used as graft substitutes in reparative and reconstructive surgery. They are especially beneficial due to their superior mechanical and thermal properties, excellent antibacterial activities, and significant biocompatibility.

Effects of Sodium Alginate on the Physical Properties and Storage Stability of Freeze-Dried Tofu Coagulated with Crab Shell Extract.

The amount of processed by-products such as crab shells is increasing, but industrial utilization is insufficient. In our previous study, crab shell extract (CSE) acted as a coagulant for tofu manufacturing. This study aimed to reduce freeze-dried (FD) tofu breakdown by improving its physical properties through adding sodium alginate (SA). FD state in tofu helps increase storage and availability, but FD tofu frequently fractures during processing, which is a concern for manufacturers. Tofu samples were prepared with either crab shell extract (CSE) or MgCl2, and SA, and freeze-dried. In the yields of FD tofu samples, there were no significant differences (p < 0.05). The brokenness of FD tofu samples was lower in CSE than in MgCl2 and was significantly reduced by SA in both tofu samples, which was affected by hardness. The water-holding capacity decreased after freeze-drying, and CSE reduced this decrease, regardless of SA addition. The microstructures differed depending on the coagulant and were dense upon SA addition. The FD tofu was packed into a multilayer film and stored at 25 °C or 45 °C for 6 months to investigate storage stability. During the storage, brokenness was unchanged in all tofu samples, indicating that they maintained their original structure. There were no significant differences in the volatile base nitrogen and thiobarbituric acid values according to the coagulant type and SA addition (p < 0.05). In conclusion, SA reduced FD tofu breakdown by improving the network structure, which may help increase FD tofu quality and decrease economic loss.