RESUMO
Current electrically heated fabrics provide heat in cold climates, suffer from abundant wasted radiant heat energy to the external environment, and are prone to damage by water. Thus, constructing energy-efficient and superhydrophobic conductive fabrics is in high demand. Therefore, we propose an effective and facile methodology to prepare a superhydrophobic, highly conductive, and trilayered fabric with a connected carbon nanotube (CNT) layer and a titanium dioxide (TiO2) nanoparticle heat-reflecting layer. We construct polyamide/fluorinated polyurethane (PA/FPU) nanofibrous membranes via first electrospinning, then performing blade-coating with the polyurethane (PU) solution with CNTs, and finally fabricating FPU/TiO2 nanoparticles via electrospraying. This strategy causes CNTs to be connected to form a conductive layer and enables TiO2 nanoparticles to be bound together to form a porous, heat-reflecting layer. As a consequence, the as-prepared membranes demonstrate high conductivity with an electrical conductivity of 63 S/m, exhibit rapid electric-heating capacity, and exhibit energy-efficient asymmetrical heating behavior, i.e., the heating temperature of the PA/FPU nanofibrous layer reaches more than 83 °C within 90 s at 24 V, while the heating temperature of the FPU/TiO2 layer only reaches 53 °C, as well as prominent superhydrophobicity with a water contact angle of 156°, indicating promising utility for the next generation of electrical heating textiles.
RESUMO
Nowadays, flexible multifunctional composites are attracting much attention and are practically being used in various emerging electronic devices. However, most composites suffer from the disadvantages of high loadings of conductive fillers, complicated preparation processes, and low energy conversion efficiency. In this article, Caffeic acid-modified multiwalled carbon nanotubes (C-MWCNTs)/poly(3,4-ethylene dioxythiophene):polystyrene sulfonic acid (PEDOT:PSS)/polyimide (PI) composite films (CPFs) were prepared using a simple layer-by-layer deposition method. The "reinforced concrete" structure of the C-MWCNTs/PEDOT:PSS layer ensures high electrical conductivity of the film, while the PI layer provides excellent mechanical properties (72.69 MPa). The composite film exhibits excellent electrothermal response and thermal stability up to approximately 125 °C at 5 V. In addition, the good conductivity of the film provides its electromagnetic shielding effectiveness (32.69 dB). With these advantages, we expect that flexible CPFs will be widely utilized in wearable devices, electromagnetic interference (EMI) shielding applications, and thermal management of personal or electronic devices.
RESUMO
This study presents the development of conductive polymer-textile composites with outstanding electric heating properties achieved through the in-situ polymerization of polypyrrole on wool-felt fabrics, renowned for their superior thermal insulation. Employing successive layer-by-layer (LBL) cycles facilitated precise control over the uniform deposition of polypyrrole with the fabrics. The investigation focused on the interaction between wool fiber and polypyrrole, evaluating appearance, add-on, and electrical heating performance with varying LBL cycles. The polymerization process resulted in the formation of spherical polypyrrole particles on the wool-felt, with deposition increasing alongside LBL cycle numbers. Mechanical properties, including tensile strength and bending rigidity, exhibited enhancement with polypyrrole deposition, while strain reduction was noted, with minimal influence from LBL cycles. Electrical properties, particularly surface resistance, displayed a rapid decrease up to the second LBL cycle. Concerning electrical heating performance, the application of a 12 V voltage resulted in a linear increase in surface temperature with increasing LBL cycles, peaking at 15.5 â. Notably, this sustained electrical heating effect persisted even after voltage removal, attributed to the low thermal conductivity of wool fiber. Moreover, the polypyrrole conductive layer maintained exceptional conductivity following repeated abrasion and washing, credited to improved uniformity through LBL cycles. The synergy of wool's insulating properties and polypyrrole's conductivity, as confirmed in this study, presents the potential for a highly efficient heating fabric. These developed materials exhibited improved heating performance, energy conservation, and minimal change in mechanical properties, making them suitable for applications such as electrical heating smart clothing.