In Situ TEM/STEM Investigation of Crystallization in Y3Al5O12:Ce at High Temperatures Inside a Transmission Electron Microscope.

Y3Al5O12:Ce (YAG:Ce) phosphors are extensively used in the field of white light-emitting diodes (LEDs) due to their efficient luminescent properties. To optimize the performance of YAG:Ce phosphors, a comprehensive understanding of their synthesis and structural evolution is essential. This paper presents a direct in situ transmission electron microscopy (TEM) /scanning TEM (STEM) investigation on the transformation process of a precursor comprising nanocrystalline CeO2 dispersed in an amorphous Y-Al oxide matrix into crystalline YAG:Ce particles. The study reveals that nanocrystalline CeO2 particles dissolve completely in the Y-Al oxide matrix at a temperature above 900 °C, while YAlO3 (YAP)-type crystalline particles with Al2O3 phase in grain boundaries are observed above 1000 °C. Finally, YAG:Ce-type crystalline particles are formed above 1180 °C. Atomic-resolution energy-dispersive X-ray spectroscopy (EDS) elemental mapping demonstrates that the doped cerium (Ce) atoms occupy the same atomic sites as yttrium (Y). Photoluminescence measurements validate the efficient luminescent properties of the obtained YAG:Ce phosphor.

Bending and reverse bending during the fabrication of novel GaAs/(In,Ga)As/GaAs core-shell nanowires monitored byin situx-ray diffraction.

We report on the fabrication of a novel design of GaAs/(In,Ga)As/GaAs radial nanowire heterostructures on a Si 111 substrate, where, for the first time, the growth of inhomogeneous shells on a lattice mismatched core results in straight nanowires instead of bent. Nanowire bending caused by axial tensile strain induced by the (In,Ga)As shell on the GaAs core is reversed by axial compressive strain caused by the GaAs outer shell on the (In,Ga)As shell. Progressive nanowire bending and reverse bending in addition to the axial strain evolution during the two processes are accessed byin situby x-ray diffraction. The diameter of the core, thicknesses of the shells, as well as the indium concentration and distribution within the (In,Ga)As quantum well are revealed by 2D energy dispersive x-ray spectroscopy using a transmission electron microscope. Shell(s) growth on one side of the core without substrate rotation results in planar-like radial heterostructures in the form of free standing straight nanowires.

Comparative clinical study of phosphorous necrosis and medical-related osteonecrosis of the jaws.

BACKGROUND: Phosphorous necrosis of the jaw (PNJ) exhibits similar clinical and pathological features as medical-related osteonecrosis of the jaw (MRONJ). This study aims at comparing the similarities and differences between PNJ and MRONJ regarding pathological features and to provide a theoretical basis for the clinical diagnosis and management of PNJ. MATERIAL AND METHODS: A retrospective analysis was conducted to assess clinical differences among 38 PNJ patients and 31 MRONJ patients, who were diagnosed and treated between January 2009 and October 2022. Pathological alterations in bone tissue were evaluated using EDS, H&E, Masson, and TRAP staining on five specimens from both MRONJ and PNJ cases; furthermore, immunohistochemistry was used to determine the expression levels of OPG, RANKL, and Runx2. The mandibular coronoid process was removed from individuals with temporomandibular joint ankylosis to serve as a control. RESULTS: CBCT imaging demonstrated necrotic bone formation in block, strip, or plaque shapes. EDS analysis showed that the calcium/phosphorus ratio in the bone tissue of PNJ and MRONJ was significantly lower than that of the control group (P < 0.05). Additionally, staining indicated reduced osteoblast counts, disrupted bone trabecular structure, and decreased collagen fiber content in the bone tissues of PNJ and MRONJ. Immunohistochemistry demonstrated that RANKL expression was significantly lower in MRONJ compared to PNJ and control groups (P < 0.05). Conversely, Runx2 expression was significantly higher in PNJ than in MRONJ and control groups (P < 0.05), and there was no significant difference in OPG expression. CONCLUSION: PNJ and MRONJ demonstrate comparable clinical manifestations and pathological traits, although disparities may exist in their underlying exhibit comparable clinical manifestations, pathological traits, and molecular mechanisms.

Carvacrol Encapsulation in Chitosan-Carboxymethylcellulose-Alginate Nanocarriers for Postharvest Tomato Protection.

Advancements in polymer science and nanotechnology hold significant potential for addressing the increasing demands of food security, by enhancing the shelf life, barrier properties, and nutritional quality of harvested fruits and vegetables. In this context, biopolymer-based delivery systems present themselves as a promising strategy for encapsulating bioactive compounds, improving their absorption, stability, and functionality. This study provides an exploration of the synthesis, characterization, and postharvest protection applications of nanocarriers formed through the complexation of chitosan oligomers, carboxymethylcellulose, and alginate in a 2:2:1 molar ratio. This complexation process was facilitated by methacrylic anhydride and sodium tripolyphosphate as cross-linking agents. Characterization techniques employed include transmission electron microscopy, energy-dispersive X-ray spectroscopy, infrared spectroscopy, thermal analysis, and X-ray powder diffraction. The resulting hollow nanospheres, characterized by a monodisperse distribution and a mean diameter of 114 nm, exhibited efficient encapsulation of carvacrol, with a loading capacity of approximately 20%. Their suitability for phytopathogen control was assessed in vitro against three phytopathogens-Botrytis cinerea, Penicillium expansum, and Colletotrichum coccodes-revealing minimum inhibitory concentrations ranging from 23.3 to 31.3 µg·mL-1. This indicates a higher activity compared to non-encapsulated conventional fungicides. In ex situ tests for tomato (cv. 'Daniela') protection, higher doses (50-100 µg·mL-1, depending on the pathogen) were necessary to achieve high protection. Nevertheless, these doses remained practical for real-world applicability. The advantages of safety, coupled with the potential for a multi-target mode of action, further enhance the appeal of these nanocarriers.

The Combined ICP-MS, ESEM-EDX, and HAADF-STEM-EDX Approach for the Assessment of Metal Sub-Micro- and Nanoparticles in Wheat Grain.

Metal sub-microparticles (SMPs) and nanoparticles (NPs) presence in food is attributable to increasing pollution from the environment in raw materials and finished products. In the present study, a multifaceted analytical strategy based on Environmental Scanning Electron Microscopy and High-Angle Annular Dark-Field-Scanning Transmission Electron Microscopy coupled with Energy-Dispersive X-ray Spectroscopy (ESEM-EDX, HAADF-STEM-EDX) and Inductively Coupled Plasma Mass Spectrometry (ICP-MS) was proposed for the detection and characterization of metal and metal-containing SMPs and NPs in durum wheat samples, covering a size measurement range from 1 nm to multiple µm. ESEM-EDX and ICP-MS techniques were applied for the assessment of SMP and NP contamination on the surface of wheat grains collected from seven geographical areas characterized by different natural and anthropic conditions, namely Italy, the USA, Australia, Slovakia, Mexico, Austria, and Russia. ICP-MS showed significant differences among the mean concentration levels of metals, with the USA and Italy having the highest level. ESEM-EDX analysis confirmed ICP-MS concentration measurements and measured the highest presence of particles < 0.8 µm in size in samples from Italy, followed by the USA. Less marked differences were observed when particles < 0.15 µm were considered. HAADF-STEM-EDX was applied to a selected number of samples for a preliminary assessment of internal contamination by metal SMPs and NPs, and to expand the measurable particle size range. The multifaceted approach provided similar results for Fe-containing SMPs and NPs. ICP-MS and ESEM-EDX also highlighted the presence of a significant abundance of Ti- and Al-containing particles, while for STEM-EDX, sample preparation artifacts complicated the interpretation. Finally, HAADF-STEM-EDX results provided relevant information about particles in the low nm range, since, by applying this technique, no particles smaller than 50 nm were observed in accordance with ESEM-EDX.

A Study on the correlation of the physico-chemical properties of Gunshot Residue (GSR) particles with distance using a 9×19 mm Indian ammunition.

The trio elements found in Gunshot Residue (GSR) are considered the key elements that are characteristic of GSR. To date, most forensic laboratories have mainly concentrated on employing carbon stubs analyzed by Scanning Electron Microscopy (SEM) coupled with Energy Dispersive Spectroscopy (EDS) to find IGSR on the hands and clothing of a person. A little elevated from the normal practice, this work is focused on the evaluation of compositional and morphological variations of GSR collected from muzzle end, trajectory, and target obtained by firing the ammunition of choice (9×19 mm Indian ammunition). Even though there may be variations in IGSR compositions within various locations of a weapon, this hasn't been investigated or documented up to this point. To ascertain whether it is possible to identify any variation in GSR particles gathered from these three different locations, the objective of this study is to investigate the structural characteristics and elemental composition of GSR to identify the distinctive parameters that allow for comparison and to establish the composition of the primer. The study also focuses on assessing any possible surface modification that may occur to GSR upon striking the target and establishing a correlation between GSR particles and propellant powder. The collected GSR samples were analyzed using a digital microscope, SEM/EDS, and EDXRF. It was discovered that the primer type showed a strong correlation to the elemental composition and morphology of GSR. By analyzing the GSR particles collected from the various sites as mentioned above, it was possible to identify the primer mixture used in the ammunition and its diversity in elemental concentration. The obtained GSR samples were not spherical but showed an elongated structure and possessed a diameter ranging from 695.4 µm-1.640 mm, 536.2 µm-1.412 mm, and 775.8 µm-1.772 mm respectively. However, the morphology and the size distribution of the particles collected from all three different points showed slight deviation as moving from ME towards TG. The obtained results could identify the primer mixture and diversity in its elemental concentration. The morphology and size distribution of GSR collected from three different points showed deviations.

The structure of the eggshell and eggshell membranes of Crocodylus niloticus.

The macro- and microstructure, elemental composition, and crystallographic characteristics of the eggshell and eggshell membranes of the Crocodylus niloticus egg was investigated using optical and electron microscopy, energy-dispersive X-ray spectroscopy (EDS), electron backscatter diffraction (EBSD) and computerised tomography. The translucent ellipsoid egg is composed of two basic layers, the outer calcified layer referred to as the shell and an inner organic fibre layer, referred to as the shell membrane. The outer inorganic calcite shell is further divided into an external, palisade and mammillary layers with pore channels traversing the shell. The external layer is a thin layer of amorphous calcium and phosphorus, the underlying palisade layer consist of irregular wedge-shaped crystals composed calcite with traces of magnesium, sodium, sulphur and phosphorus. The crystals are mostly elongated, orientated perpendicular to the shell surface ending in cone-shaped knobs, which forms the inner mammillary layer. The elemental composition of the mammillae is like that of the palisade layer, but the crystal structure is much smaller and orientated randomly. The highest number of mammillae and shell pores are found at the equator of the egg, becoming fewer towards the egg poles. The shell thickness follows the same pattern, with the thickest area located at the equator. The eggshell membrane located right beneath and embedded in the mammillary layer of the shell; it is made up of unorganised fibre sheets roughly orientated at right angles to one another. Individual fibres consist of numerous smaller fibrils forming open channels that run longitudinally through the fibre.

Deep Learning-Assisted Multivariate Analysis for Nanoscale Characterization of Heterogeneous Beam-Sensitive Materials.

Nanoscale materials characterization often uses highly energetic probes which can rapidly damage beam-sensitive materials, such as hybrid organic-inorganic compounds. Reducing the probe dose minimizes the damage, but often at the cost of lower signal-to-noise ratio (SNR) in the acquired data. This work reports the optimization and validation of principal component analysis (PCA) and nonnegative matrix factorization for the postprocessing of low-dose nanoscale characterization data. PCA is found to be the best approach for data denoising. However, the popular scree plot-based method for separation of principal and noise components results in inaccurate or excessively noisy models of the heterogeneous original data, even after Poissonian noise weighting. Manual separation of principal and noise components produces a denoised model which more accurately reproduces physical features present in the raw data while improving SNR by an order of magnitude. However, manual selection is time-consuming and potentially subjective. To suppress these disadvantages, a deep learning-based component classification method is proposed. The neural network model can examine PCA components and automatically classify them with an accuracy of >99% and a rate of ∼2 component/s. Together, multivariate analysis and deep learning enable a deeper analysis of nanoscale materials' characterization, allowing as much information as possible to be extracted.

Candida massiliensis sp. nov. Isolated from a Clinical Sample.

The majority of Candida species are known as non-pathogenic yeasts and rarely involved in human diseases. However, recently case reports of human infections caused by non-albicans Candida species have increased, mostly in immunocompromised hosts. Our study aimed to describe and characterize as thoroughly as possible, a new species of the Metschnikowia clade, named here Candida massiliensis (PMML0037), isolated from a clinical sample of human sputum. We targeted four discriminant genetic regions: "Internal Transcribed Spacers" of rRNA, D1/D2 domains (28S large subunit rRNA) and part of the genes encoding Translation Elongation Factor 1-α and ß-tubulin2. The genetic data were compared to morphological characters, from scanning electron microscopy (TM 4000 Plus, SU5000), physiological, including the results of oxidation and assimilation tests of different carbon sources by the Biolog system, and chemical mapping by Energy-Dispersive X-ray Spectroscopy. Lastly, the in vitro antifungal susceptibility profile was performed using the E-test™ exponential gradient method. The multilocus analysis supported the genetic position of Candida massiliensis (PMML0037) as a new species of the Metschnikowia clade, and the phenotypic analysis highlighted its unique morphological and chemical profile when compared to the other Candida/Metschnikowia species included in the study.

Multi-Analytical Techniques for the Study of Burial Clothes of Polish King Sigismund III Vasa (1566-1633) and His Wife Constance Habsburg (1588-1631).

The subjects of this research are the burial clothes of Polish King Sigismund III Vasa and his wife Constance, which were woven and embroidered with silk and metal threads. Fragments of the textiles underwent spectroscopic, spectrometric, and thermogravimetric analyses. The hydrofluoric acid extraction method was improved to isolate various classes of dyes from the textile samples that had direct contact with human remains. High-performance liquid chromatography, coupled with diode array and tandem mass spectrometry detectors with electrospray ionization (HPLC-DAD-ESI-MS/MS) facilitated the detection and identification of colorants present in the textiles. Cochineal, indigo-, madder-, orchil-, and tannin-producing plants were identified as the sources of dyes used. Scanning electron microscopy with an energy-dispersive X-ray detector (SEM-EDS) was employed to identify and characterize the silk fibers and mordants and the metal threads. The presence of iron, aluminum, sodium, and calcium in the silk threads suggests their potential use as mordants. The analysis of the metal threads revealed that most of them were made from flattened gilded silver wire, with only a few being cut from a sheet of metal. Typical degradation mechanisms of metal threads were shown, resulting from both burial environment and earlier manufacturing process, and the use of the textiles in clothing, i.e., a significant loss of the gold layer was observed in most of silver gilt threads, caused by abrasion and delamination. The results of the thermal analysis confirmed the presence of silk and silver threads in the examined textiles.

[Age prediction based on the examination of bone tissue elemental composition using energy dispersive X-Ray spectroscopy]. / Prognozirovanie vozrasta na osnovanii izucheniya elementnogo sostava kostnoi tkani s pomoshch'yu energodispersionnoi rentgenovskoi spektroskopii.

THE AIM OF THE STUDY: Was to assess the possibility of using chemical analysis of bone mineral content by the means of an energy dispersive X-Ray spectroscopy to determine the age of unidentified corpses for forensic identification. A semi-quantative chemical microanalysis of bone fragments of 85 male and female corpses aged between 21 and 91 was done through the use of energy dispersive X-Ray spectrometer. The association of bone tissue apatite mineral composition with age is confirmed and a formula, connecting age and chemical composition change, is proposed. The possibility of using quantitive evaluation of chemical elements content in the normative mineral to determine the unidentified corpse's age in a standard laboratory, equipped with an energy dispersive X-Ray spectrometer, was proved.

Estimation of linear and mass attenuation coefficients of soy-lignin bonded Rhizophora spp. particleboard as a potential phantom material using caesium-137 and cobalt-60.

In this study, linear and mass attenuation coefficients of fabricated particleboards intended for use as phantom material were estimated using 137Cs and 60Co radiation sources. Particleboards made of Rhizophora spp. wood trunk bonded with soy flour and lignin were fabricated at a target density of 1.0 g cm-3, with and without gloss finish coating. Elemental composition of the particleboards was obtained by means of energy dispersive X-ray (EDX) spectroscopy. Experimental setups were simulated via the GATE Monte Carlo (MC) package, with particle histories of 1 × 106-1 × 107. Linear and mass attenuation coefficients obtained from measurements and GATE simulations were compared and discussed. The percentage differences between the measured and simulated linear and mass attenuation coefficients of the samples were reasonably small (2.05-4.88% for 137Cs and 3.24-5.38% for 60Co). It is shown that all the particleboards have the potential to be used as phantom materials as the attenuation coefficients measured were in good agreement with those of water (calculated with XCOM) and with those simulated with the GATE toolkit. The use of gloss finish coating also did not show any significant effect on the attenuation coefficient of the phantom material. Verification of experimental results via GATE simulations has been shown crucial in providing reliable data for energy transmission studies. Based on the results achieved in this study, it is concluded that the studied material-Rhizophora spp. wood trunk bonded with soy flour and lignin including gloss finish coating-can be used in radiation dosimetry studies.

Improving Quantitative EDS Chemical Analysis of Alloy Nanoparticles by PCA Denoising: Part II. Uncertainty Intervals.

Analytical studies of nanoparticles (NPs) are frequently based on huge datasets derived from hyperspectral images acquired using scanning transmission electron microscopy. These large datasets require machine learning computational tools to reduce dimensionality and extract relevant information. Principal component analysis (PCA) is a commonly used procedure to reconstruct information and generate a denoised dataset; however, several open questions remain regarding the accuracy and precision of reconstructions. Here, we use experiments and simulations to test the effect of PCA processing on data obtained from AuAg alloy NPs a few nanometers wide with different compositions. This study aims to address the reliability of chemical quantification after PCA processing. Our results show that the PCA treatment mitigates the contribution of Poisson noise and leads to better quantification, indicating that denoised results may be reliable from the point of view of both uncertainty and accuracy for properly planned experiments. However, the initial data need to be of sufficient quality: these results can only be obtained if the signal-to-noise ratio of input data exceeds a minimal value to avoid the occurrence of random noise bias in the PCA reconstructions.

Chemical and Structural Alterations in the Amorphous Structure of Obsidian due to Nanolites.

Obsidian is volcanic glass that results from the rapid cooling of silica-rich melt. Nanoscale crystallites precipitate out of the melt prior to solidification and remain embedded in the amorphous matrix. These crystallites provide information on the flow kinetics and composition of the melt. Due to the sparsity and size of nanolites, studies often focus on supramicron crystallites. This research takes advantage of the conchoidal fracture of obsidian by knapping samples with nanometer-thin edges for transmission electron microscopy characterization. Nanolites in the amorphous matrix are studied using energy-dispersive spectroscopy (EDS) and electron diffraction. Certain alkali and alkaline-earth cations exhibit patterns of depletion near Fe-oxide nanolites. EDS is used to identify nanolites and variations in the composition of the matrix. Parallel beam diffraction and radial distribution function analysis of nearest-neighbor distances determine average bond lengths in the matrix near nanolites, showing that nanolites influence the nearby short-range ordering and atomic character of the matrix. Analysis reveals decreased mean nearest-neighbor distances in the matrix adjacent to nanolites compared to the bulk. Our methods exhibit the required sensitivity to detect variations in the composition and structure near nanolites, and our findings indicate that obsidian nanolites contribute to quantifiable localized changes in the amorphous structure.

Space weathering signatures in sulfide and silicate minerals from asteroid Itokawa.

Transmission electron microscopy analyses of the polymineralic regolith particle RC-MD01-0025 show microstructural and microchemical characteristics indicative of space weathering on the surface of asteroid Itokawa. The depletion of sulfur and nickel was identified in space weathered rims on troilite and pentlandite minerals. This corresponds to the first report of nickel depletion in samples returned from asteroid Itokawa by the Hayabusa mission. Microstructurally, the sulfide minerals present crystalline rims and the olivine presents both crystalline and amorphous zones in the rim. These results suggest that sulfides might be more resistant to amorphization caused by solar wind irradiation. The space weathering features identified in the regolith particle analyzed here are likely formed via solar wind irradiation. Additionally, the differences in the space weathering features in olivine, pentlandite, and troilite suggest that silicates and sulfides respond differently to the same space weathering conditions in interplanetary space.

Comparison of Dentin Caries Remineralization with Four Bioactive Cements.

The treatment of deep carious lesions involves the use of ion-releasing agents to seal the lesions. These agents release minerals, leading to the remineralization of the remaining demineralized dentin. This study aimed to compare the dentin caries remineralization with bioactive cements. 60 Dentin blocks were prepared from the dentin of human third molars. Artificial carious lesions were induced on the blocks with pH cycling. The samples were divided into five groups (n=12). Dycal, Oxford ActiveCal PC, Biodentine, and ACTIVA BioACTIVE were applied using a mold. One group did not receive any cement. The samples were stored in remineralization solution for 30 days. The cement was removed using a #15 blade, and the dentin surface was evaluated using Energydispersive X-ray Spectroscopy and X-ray Diffraction. One-way ANOVA did not show a significant difference in the weight percentages of calcium and phosphorus and the calcium-to-phosphorus ratios between the groups. The highest and the lowest weight percentages of calcium and phosphorus were observed in Biodentine and control groups, respectively. There were no significant differences in the remineralization properties of bioactive cements. Hydroxyapatite crystals were not formed in any of the adjacent dentin using these cements.

Observation of Silicone Oil Within the Vitreous and Sclera Following Intravitreal Administration of Biotherapeutics Using Insulin Syringes in Cynomolgus Monkeys.

Silicone oil droplets have been reported in the eyes of human patients following intravitreous (IVT) injections with several marketed biotherapeutic products. Intravitreous administration of a novel biotherapeutic in a 14-week cynomolgus monkey study using insulin syringes was associated with 2, non-test-article-related phenomena: "vitreous floater/clear sphere" on indirect ophthalmoscopy and intrascleral "foreign material near injection track" on histopathology. Retrospective analysis of 81 other preclinical studies of IVT administration of novel biotherapeutics found a greater frequency of clear spheres in monkey IVT studies using insulin syringes and formulations containing polysorbate. We were able to correlate microscopic findings of clear circular to oval areas in the sclera near the injection track with an energy-dispersive X-ray spectroscopy (EDS) signal for silicon at the same location in the sclera. These observations provide further evidence that silicone lubricant in insulin syringes/needles is the source of clear spheres noted in the vitreous and foreign material noted near the injection track in the sclera. Although considered inert and toxicologically insignificant, silicone deposition within the eye should form part of the risk-benefit equation in a clinical setting.

Statistical Analysis of Polymer Nanocomposites for Mechanical Properties.

Epoxy resins, due to their high stiffness, ease of processing, good heat, and chemical resistance obtained from cross-linked structures, have found applications in electronics, adhesives coatings, industrial tooling, and aeronautic and automotive industries. These resins are inherently brittle, which has limited their further application. The emphasis of this study is to improve the properties of the epoxy resin with a low-concentration (up to 0.4% by weight) addition of Multi-Walled Carbon Nanotubes (MWCNTs). Mechanical characterization of the modified composites was conducted to study the effect of MWCNTs infusion in the epoxy resin. Nanocomposites samples showed significantly higher tensile strength and fracture toughness compared to pure epoxy samples. The morphological studies of the modified composites were studied using Scanning Electron Microscopy (SEM).

Effects of 45S5 bioactive glass on the remineralization of early carious lesions in deciduous teeth: an in vitro study.

BACKGROUND: Early childhood caries has been designated as a serious public health problem. The traditional restoration method is very challenging, especially in uncooperative patients. Non-invasive therapy, like remineralization agents, which have been developed to reverse the demineralization progress at the early stage of caries, may be a better choice. This study aimed to evaluate the remineralization efficacy of different concentrations of 45S5 bioactive glass (BAG) on artifical carious lesions of deciduous enamel. METHODS: 65 caries-like enamel lesions of the deciduous teeth were assigned to 5 groups (n = 13) and transported to a 14 days pH-cycling: Group A: 2%BAG, Group B: 4%BAG, Group C: 6%BAG, Group D: 8%BAG, and Group E: deionized water (DDW, negative control). 8 sound (Group F) and 8 demineralized teeth (Group G) were prepared for contrast. The recovery power of mechanical property was evaluated by Vickers hardness test through the recovery of enamel microhardness (%REMH). Surface morphology, mass fraction of Ca and P ions, and Ca/P atomic ratio were analyzed by scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (EDX). Moreover, Fourier transform infrared spectroscopy equipped with attenuated total reflectance was used to identify the chemical structure of newly formed compounds. RESULTS: % REMH were (42.65 ± 1.35), (52.59 ± 2.96), (57.40 ± 1.72), (52.91 ± 2.55), (12.46 ± 2.81) in 2%BAG, 4%BAG, 6%BAG, 8%BAG, and DDW groups respectively. Micro-spherical particles were deposited in all BAG groups and 6% BAG showed the densest and most uniform surface. EDX analysis identified significantly higher Ca(wt%) and P(wt%) in four BAG groups than in the demineralized group (p < 0.005), while 6% BAG showed the highest mineral gain efficacy. The infrared spectrum demonstrated that newly mineralized crystals were consisted of type-B hydroxycarbonate apatite. CONCLUSION: BAG possessed a promising remineralization effect on artificial lesions in deciduous enamel by recovering enamel surface mechanical property, morphology and chemical elements. Among them, 6% BAG performed the greatest overall efficacy. Acting as a new caries-arresting biomaterial, 45S5 BAG has the potential to facilitate the adaptation of better carious prevention strategies in children.

Osteogenic differentiation of human bone marrow-derived mesenchymal stem cells is enhanced by an aragonite scaffold.

Bone graft substitutes and bone void fillers are predominantly used to treat bone defects and bone fusion in orthopaedic surgery. Some aragonite-based scaffolds of coralline exoskeleton origin exhibit osteoconductive properties and are described as useful bone repair scaffolds. The purpose of this study was to evaluate the in vitro osteogenic potential of the bone phase of a novel aragonite-based bi-phasic osteochondral scaffold (Agili-C™, CartiHeal Ltd.) using adult human bone marrow-derived mesenchymal stem cells (MSCs). Analyses were performed at several time intervals: 3, 7, 14, 21, 28 and 42 days post-seeding. Osteogenic differentiation was assessed by morphological characterisation using light microscopy after Alizarin red and von Kossa staining, and scanning electron microscopy. The transcript levels of alkaline phosphatase (ALP), runt-related transcription factor 2 (RUNX2), bone gamma-carboxyglutamate (BGLAP), osteonectin (SPARC) and osteopontin (SPP1) were determined by quantitative PCR. Proliferation was assessed by a thymidine incorporation assay and proliferating cell nuclear antigen (PCNA) immunocytochemistry. Our results demonstrate that the bone phase of the bi-phasic aragonite-based scaffold supports osteogenic differentiation and enhanced proliferation of bone marrow-derived MSCs at both the molecular and histological levels. The scaffold was colonized by differentiating MSCs, suggesting its suitability for incorporation into bone voids to accelerate bone healing, remodelling and regeneration. The mechanism of osteogenic differentiation involves scaffold surface modification with de novo production of calcium phosphate deposits, as revealed by energy dispersive spectroscopy (EDS) analyses. This novel coral-based scaffold may promote the rapid formation of high quality bone during the repair of osteochondral lesions.