Is cement-augmented sacroiliac screw fixation with partially threaded screws superior to that with fully threaded screws concerning compression and pull-out force in fragility fractures of the sacrum? - a biomechanical analysis.

BACKGROUND: Providing a stable osteosynthesis in fragility fractures of the pelvis can be challenging. Cement augmentation increases screw fixation in osteoporotic bone. Generating interfragmentary compression by using a lag screw also improves the stability. However, it is not known if interfragmentary compression can be achieved in osteoporotic sacral bone by cement augmentation of lag screws. The purpose of this study was to compare cement-augmented sacroiliac screw osteosynthesis using partially versus fully threaded screws in osteoporotic hemipelvises concerning compression of fracture gap and pull-out force. METHODS: Nine fresh-frozen human cadaveric pelvises with osteoporosis were used. In all specimens, one side was treated with an augmented fully threaded screw (group A), and the other side with an augmented partially threaded screw (group B) after generating a vertical osteotomy on both sides of each sacrum. Afterwards, first a compression test with fracture gap measurement after tightening of the screws was performed, followed by an axial pull-out test measuring the maximum pull-out force of the screws. RESULTS: The fracture gap was significantly wider in group A (mean: 1.90 mm; SD: 1.64) than in group B (mean: 0.91 mm; SD: 1.03; p = 0.028). Pull-out force was higher in group A (mean: 1696 N; SD: 1452) than in group B (mean: 1616 N; SD: 824), but this difference was not statistically significant (p = 0.767). CONCLUSIONS: Cement augmentation of partially threaded screws in sacroiliac screw fixation allows narrowing of the fracture gap even in osteoporotic bone, while resistance against pull-out force is not significantly lower in partially threaded screws compared to fully threaded screws.

The potential biomechanical advantage of lag by technique screw fixation of the posterior pelvic ring.

PURPOSE: Diastasis of the sacroiliac joint after pelvic ring injury is commonly reduced by lagging by design with partially threaded (PT) screws. There may be a biomechanical benefit to lagging by technique with fully threaded (FT) screws. The purpose of this study was to compare these two methods. METHODS: Twelve pairs of synthetic bone blocks were lagged together with 8.0-mm FT or PT screws. Maximum compressive and steady-state force was measured. Pullout force testing was performed. RESULTS: The maximum compressive force of FT and PT screws was not different [mean difference (MD) 32 Newtons (N), 95% confidence interval (CI) 124, 60)]; however, lagging by technique with FT screws resulted in significantly higher steady-state force (MD 83 N, 95% CI 165, 5) and pullout force (MD 634 N, 95% CI 778, 491). CONCLUSION: Lagging by technique with large diameter FT screws has a biomechanical advantage over lagging by design with PT screws.

Use of fully threaded cannulated screws decreases femoral neck shortening after fixation of femoral neck fractures.

BACKGROUND: Femoral neck fractures (FNF) are becoming increasingly common as population ages. Nondisplaced fractures are commonly treated by cancellous, parallel placed, partially threaded cannulated screws (PTS). This allows controlled fracture impaction. However, sliding implants can lead to femoral neck shortening (FNS) that has been shown to be correlated with reduced quality of life and impaired gait pattern. Recently, in our institution we have changed the fixation of FNF to fully threaded screws (FTS) with or without an additional partially threaded screw in order to minimize this phenomenon. The aim of this study was to compare the FNS in patients treated with FTS as compared with our historical controls treated with PTS. PATIENTS AND METHODS: Between 2014 and 2016, 38 patients with FNF were treated with FTS. Out of the 38, 24 were available for radiographic follow-up. 41 patients treated previously with PTS were available as a control group. Radiographic analysis was performed to assess the FNF in three vectors: Horizontal (X), Vertical (Y) and overall (Z) according to the neck-shaft angle. RESULTS: Time for admission to surgery was longer in the PTS group (p = 0.04). Patient demographics and major complication rates were similar in the two patient groups. Average FNS in the X axis was significantly smaller in the FTS group than in the PTS group (2.8 ± 3.6 vs 7.6 ± 4.2 mm, p < 0.01) as well as the Y axis (1.2 ± 2.6 vs 4.9 ± 4.2 mm, p < 0.01) and thus also decreased overall Z shortening (2.3 ± 3.5 vs 6.23 ± 4.5 mm, p < 0.01). There was a tendency towards a more valgus reduction in the PTS (137° vs 134°, p = 0.08). There was a significantly smaller number of FTS patients with moderate (5-10 mm) or severe (> 10 mm) FNS. Screw pull-out > 5 mm occurred in 17/41 patients in the PTS but none in the FTS group (p < 0.01). CONCLUSION: This study proves that use of FTS improves the radiographic results following FNF fixation using cannulated screws.

The use of fully threaded headless cannulated screws for femoral neck fracture fixation in small-breed dogs show promise in cadaveric study.

OBJECTIVE: To biomechanically evaluate the stability of internal fixation methods for femoral neck fractures in small-breed dogs. Furthermore, the possibility of replacing the headed screw with fully threaded headless cannulated screws in the fixation method was assessed. METHODS: The study was conducted from December 12, 2023, to February 7, 2024. A total of 18 femurs from 9 canine cadavers were used in this study. After a simple neck fracture was created, in group A (n = 6), the fracture was stabilized with three 1.1-mm parallel Kirschner wires (K-wires). In group B (n = 6), a 3.0-mm partially threaded cannulated screw and an antirotation pin were used. In group C (n = 6), a 2.5-mm fully threaded headless cannulated screw and an antirotation pin were used. A mechanical test was conducted to apply a single axial compressive load to the femoral head. RESULTS: 9 adult small-breed dogs weighing 3.6 to 8.3 kg (mean ± SD; 5.9 ± 1.6). The mean maximum failure load was highest in group C (495 ± 81 N), followed by group B (454 ± 50.4 N), and then group A (222 ± 21.6 N). Significant differences in maximum failure load were observed between groups A and B as well as groups A and C but not between groups B and C. CONCLUSION: The use of fully threaded headless cannulated screws presents a promising method for internal fixation of canine femoral neck fractures. CLINICAL RELEVANCE: To demonstrate the potential stability and reliability of fully threaded headless cannulated screws.

Internal fixation using fully threaded cannulated compression screws for fresh femoral neck fractures in adults.

OBJECTIVES: Internal fixation with multiple cannulated compression screws is an optional treatment for femoral neck fracture. Recently, fully threaded cannulated compression screws (FTCCS) have been introduced to fix fresh femoral neck fractures (FNF). The purpose of this study was to investigate the effectiveness of FTCCS. PATIENTS AND METHODS: Patients with FNF fixed by multiple FTCCS from February 1st, 2014 to August 31st, 2017 were included in this study. They were followed for at least 12 months postoperatively. Nonunion, osteonecrosis of the femoral head (ONFH), fixation failure, reoperation, and femoral neck shortening (FNS) were used to evaluate the outcomes. Risk factors including age, sex, fracture side, fracture displacement, fracture stability, fixation configuration, and screw numbers were analyzed. RESULTS: A total of 113 patients including 67 males and 46 females with an average age of 48.4 ± 13.4 years were included. The mean duration of follow-up was 27.1 months (range: 12-51 months). The incidence of nonunion, ONFH, fixation failure, and reoperation was 15.9%, 22.1%, 8.8%, and 24.8%, respectively. The rates of nonunion and reoperation were significantly higher in displaced fractures and unstable fractures. And patients with an unstable fracture had a higher risk of internal fixation failure. The median length of FNS was 2.9 mm (interquartile range: 0.9-6.5 mm, range: 0-17.5 mm). Age was a significant risk factor for FNS. CONCLUSIONS: The screw fixation method with FTCCS provided encouraging clinical results which may be a rational choice for the treatment of fresh FNF. Displaced fractures and unstable fractures were attributed to the higher incidence of complications. TRIAL REGISTRATION: ChiCTR, ChiCTR1800017200. Registered 17 July 2018-Retrospectively registered, http: www.chictr.org.cn/showprojen.aspx?proj=29182 .

Hybrid screw fixation for femoral neck fractures: Does it prevent mechanical failure?

INTRODUCTION: Traditionally, femoral neck fracture fixation has been performed using three partially threaded cancellous screws. However, fracture collapse with femoral neck shortening, and varus deformation frequently occurs due to posterior medial comminution and lack of calcar support. We hypothesize replacing the inferior neck/calcar screw with a fully threaded, length stable, screw will provide improved biomechanical stability, decrease femoral neck shortening and varus collapse. METHODS: Ten matched cadaveric pairs (20 femurs) were randomly assigned to two screw fixation groups. Group 1 (Hybrid) utilized one fully threaded calcar screw & two partially threaded superior screws. Group 2 (PT) utilized all partially threaded screws. Specimens underwent standardized femoral neck osteotomies, 45° from the horizontal, with 5 mm posteromedial wedge removed to simulate posteromedial comminution. Screws were placed using fluoroscopic guidance. Specimens were biomechanically tested using two loading sequences: 1) Axial load applied up to 700 N, followed by cyclic loading at 2 Hz with loads of 700 to 1,400 N for 10,000 cycles. 2) All surviving constructs were cyclically loaded to failure in stepwise incremental manner with max load of 4,000 N. Paired t-tests used to compare stiffness, cycles to failure, and max load to failure (defined as 15 mm load actuator displacement). RESULTS: Construct stiffness was 2848 ± 344 N/mm in PT vs. 2767 ± 665 for Hybrid (P = 0.628). Load to failure demonstrated, hybrid superiority with max cycles to failure (3797 ± 400 cycles) vs. (2981 ± 856 cycles in PT) (p = 0.010), and max load prior to failure (3290 ± 196 N) vs. (2891 ± 421 N in PT) (p = 0.010). No significant difference in bone mineral density was noted in any of the specimens. CONCLUSIONS: Our study is the first to assess the biomechanical effects of hybrid fixation for femoral neck fractures. Hybrid screw configuration resulted in significantly stronger constructs, with higher axial load and increased cycles prior to failure. The advantageous mechanical properties demonstrated using a fully threaded inferior calcar screw provides a length stable construct which may prevent the common complication of excessive femoral neck shortening, varus collapse and poor functional outcome.

Numerical and Experimental Analysis of the Load-Carrying Capacity of a Timber Semi-Rigid Dowel-Type Connection.

The paper deals with the analysis of the load-carrying capacity of a timber semi-rigid connection created from a system of two stands and a rung. The connection was made from glued laminated timber with metal mechanical dowel-type fasteners. Not only a common combination of bolts and dowels, but also fully threaded screws were used for the connection. The aim of the research and its motivation was to replace these commonly used fasteners with more modern ones, to shorten and simplify the assembly time, and to improve the load-carrying capacity of this type of connection. Each of these two types of connections was loaded statically, with a slow increase in force until failure. The paper presents results of the experimental testing. Three specimens were made and tested for each type of the connection. Experimental results were subsequently compared with numerical models. The achieved results were also compared with the assumption according to the currently valid standard. The results indicate that a connection using fully threaded screws provides a better load-carrying capacity.

Numerical and Experimental Analysis of the Rotational Stiffness of a Timber Semi-Rigid Dowel-Type Connection.

The paper deals with the analysis of the rotational stiffness of a semirigid connection created from a system of two stands and a rung. The connection was made from glued laminated timber with metal mechanical dowel-type fasteners. Not only a common combination of bolts and dowels but also fully threaded screws were used for the connection. The aim of the research and its motivation was to replace commonly used fasteners with more modern ones, to shorten and simplify the assembly time, and to improve the load-carrying capacity of this type of connection. Each of these two types of connection was loaded to the level of 60%, 80%, and 100% of the ultimate limit state value. Subsequently, the rotational stiffness was determined for each load level after five loading and unloading cycles. This paper presents the results and comparison of the experimental testing and the numerical modeling. The obtained results were also compared with the assumption according to the currently valid standard.

Decreased complications but a distinctive fixation loosening mechanism of fully threaded headless cannulated screw fixation for femoral neck fractures in young adults.

BACKGROUND: Despite being a commonly encountered injury in orthopedic practice, controversy surrounds the methods of optimal internal fixation for femoral neck fractures (FNF) in young patients. The objective of the present study is to compare complication rates and failure mechanisms for surgical fixation of FNF using fully threaded headless cannulated screws (FTHCS) versus partial threaded cannulated screws (PTS) in young adults. METHODS: A total of 75 patients (18-65 years old) with FNF were prospectively treated with close reduction and internal fixation using three parallel FTHCS and compared to a historical control case-matched group (75 patients) with FNF treated by PTS fixation. After 2 years follow-up, rates of fixation failure (including varus collapse, fracture displacement, and femoral neck shortening), nonunion, and avascular necrosis of the femoral head (ANFH) were compared between the two cohorts. The demographic, follow-up information, and radiological images were assessed by independent blinded investigators. RESULTS: Patient demographics and fracture patterns were similar in the two patient groups. The overall fixation failure rates were 8% (6/75) in the FTHCS cohort, which was significantly lower than the 25.3% (19/75) seen in the PTS group. Rates of nonunion and ANFH were significantly lower in the FTHCS group when compared to the PTS control group. When stratified by injury severity (high-energy vs. low-energy fractures), the rate of fixation failure was significant lower with the use of FTHCS when compared with PTS for high-energy fractures while there was no difference in the rates of nonunion or ANFH for high or low-energy fracture patterns. Unique to the FTHCS cohort was an atypical screw migration pattern with varus collapse (6/75, 8%). CONCLUSIONS: The results show that FTHCS fixation could significantly reduce the complication rate of young patients with FNF, especially in high-energy fracture patterns (Garden III-IV, Pauwels III, or vertical of the neck axis (VN) angle ≥ 15°). There was also confirmation that the modes of fixation loosening in the FTCHS group, including screw "medial migration" and superior cutout, were different from the screw withdrawal pattern seen in the PTS cohort. TRIAL REGISTRATION: The study was retrospectively registered at www.Chictr.org.cn ( ChiCTR-IPR-1900025851 ) on September 11, 2019.

Sacroiliac joint arthropathy in adult spinal deformity patients with long constructs to the pelvis.

OBJECTIVE: Sacroiliac joint (SIJ) arthropathy is an increasingly recognized problem in adult spinal deformity patients undergoing long construct surgery. S2-alar-iliac (S2AI) screw instrumentation is thought to reduce morbidity from pelvic fixation in these patients. The goal of this study is to assess the overall incidence of SIJ arthropathy in patients with long constructs to the pelvis as well as compare SIJ outcomes of partially threaded (PT) versus fully threaded (FT) S2AI screws. METHODS: Data of eligible patients were collected from a prospectively maintained database with retrospective review of electronic records at an academic institution between 2016 and 2019. RESULTS: 65 consecutive patients who underwent S2AI screw instrumentation (40 in PT group, 25 in FT group) were enrolled. The rate of postoperative SIJ pain was higher in the PT (52.5 %) compared to FT (32 %) group. There was a significantly shorter time-to-pain development in the PT compared to FT group (11.8 versus 20.1 months, respectively). Of those who developed SIJ pain in the PT group, the pain worsened in 80.9 % versus only 25 % of those in the FT group despite conservative treatment. Cox regression found the PT group more likely to develop SIJ pain at any point during follow-up compared to the FT group (Hazard Ratio = 7.308). SIJ fusion was not detected on imaging of any patient during follow-up. CONCLUSION: FT S2AI screws are associated with better SIJ outcomes compared to PT screws. However, our data suggest that S2AI screw instrumentation is not sufficient to achieve fusion or prevent development of SIJ pain. Concurrent SIJ fusion may be necessary in patients with long constructs to prevent SIJ arthropathy.

Posterior fully threaded positioning screw prevents femoral neck collapse in Garden I or II femoral neck fractures.

INTRODUCTION: Osteosynthesis is recommended for Garden I and II femoral neck fracture treatment using parallel partially threaded cannulated screws. Postoperatively, excessive femoral neck shortening (FNS) and posterior tilt of the femoral neck (PTFN) are frequently encountered and are correlated with impaired quality of life and clinical outcomes. We hypothesized that stabilization by parallel partially threaded cannulated screws replacing a posterior partially threaded screw with a fully threaded positioning screw would improve fracture healing without further FNS and PTFN in femoral neck fractures. METHODS: We retrospectively reviewed Garden I and II femoral neck fractures treated by in situ fixation using parallel cannulated screws at our institution between January 2010 and November 2018. Patients with the applicable fractures were divided according to the utilization of posterior fully threaded screws: patients with partially threaded screws were included in Group C and those with posterior fully threaded screws were included in Group P. Intergroup comparisons were performed based on radiographic measurements that assessed the shortening in two vectors (the horizontal and vertical axes), FNS, and subsequent PTFN. RESULTS: No significant intergroup difference was found in demographics and fracture characteristics, except in the follow-up duration. The mean FNS and shortening in both vectors were significantly smaller in Group P than in Group C (FNS, 5.02 ± 1.31 vs. 8.84 ± 3.48 mm, p < 0.001; horizontal axis, 4.07 ± 1.06 vs. 6.18 ± 2.77 mm, p < 0.001; and vertical axis, 2.55 ± 1.68 vs. 5.74 ± 3.41 mm, p < 0.001). The mean subsequent PTFN was significantly smaller in Group P (2.21 ± 2.99 vs. 7.56 ± 6.20 mm, p < 0.001). A significantly smaller number of patients in Group P had moderate (5-10 mm) or severe (>10 mm) FNS and moderate (5-10°) or severe (>10°) subsequent PTFN. CONCLUSION: Parallel cannulated screws replacing a posterior partially threaded screw with a fully threaded positioning screw as a length- and angle-stable construct for Garden I or II femoral neck fracture fixation can prevent femoral neck collapse in both the coronal and axial planes.

Fully threaded sacroiliac lag screws have higher load to failure when compared to partially threaded screws: A biomechanical study.

The purpose of this study is to compare biomechanical properties of fully and partially threaded iliosacral screws. We hypothesise that fully threaded screws will have a higher yield force, and less deformation than partially threaded screws following axial loading. Twenty sawbone blocks were uniformly divided to simulate vertical sacral fractures. Ten blocks were affixed with fully threaded iliosacral screws in an over-drilled, lag-by-technique fashion whilst the remaining ten were fixed with partially threaded lag-by-design screws. All screws measured 7.3-mm x 145 mm, and were inserted to a 70% of calculated maximal insertional torque, ensuring uniform screw placement throughout across models. Continuous axial loads were applied to 3 constructs of each type to failure to determine baseline characteristics. Five hundred loading cycles of 500 N at 1 Hz were applied to 4 constructs of each type, and then axially loaded to failure. Force displacement curves, elastic, and plastic deformation of each construct was recorded. Fully threaded constructs had a 428% higher yield force, 61% higher stiffness, 125% higher ultimate force, and 66% lower yield deformation (p < 0.05). The average plastic deformation for partially threaded constructs was 336% higher than fully threaded constructs (p = 0.071), the final elastic deflection was 10% higher (p = 0.248), and the average total movement was 21% higher (p = 0.107). We conclude from this biomechanical study that fully threaded, lag-by-technique iliosacral screws can withstand significantly higher axial loads to failure than partially threaded screws. In addition, fully threaded screws trended towards exhibiting a significantly lower plastic deformation following cyclical loading.

Effect of interfragmentary gap on compression force in a headless compression screw used for scaphoid fixation.

We investigated the effect of an interfragmentary gap on the final compression force using the Acutrak 2 Mini headless compression screw (length 26 mm) (Acumed, Hillsboro, OR, USA). Two blocks of solid rigid polyurethane foam in a custom jig were separated by spacers of varying thickness (1.0, 1.5, 2.0 and 2.5 mm) to simulate an interfragmentary gap. The spacers were removed before full insertion of the screw and the compression force was measured when the screw was buried 2 mm below the surface of the upper block. Gaps of 1.5 mm and 2.0 mm resulted in significantly decreased compression forces, whereas there was no significant decrease in compression force with a gap of 1 mm. An interfragmentary gap of 2.5 mm did not result in any contact between blocks. We conclude that an increased interfragmentary gap leads to decreased compression force with this screw, which may have implications on fracture healing.

Achieving interfragmentary compression without special drilling technique or screw design.

Traditional fracture fixation teaching suggests that fully threaded screws do not provide interfragmentary compression unless placed through a glide hole. Based on this assumption, pelvic surgeons typically use fully threaded screws in the treatment of comminuted transforaminal sacral fractures to limit iatrogenic neuroforaminal stenosis. Clinical experience with fully threaded screws suggests that interfragmentary compression actually does occur. We hypothesized that the use of a fully threaded screw does not produce any interfragmentary compression and that there is no difference in insertional torque between partially threaded and fully threaded screws. To test this hypothesis, fully and partially threaded 7.0 millimeter (mm) cannulated screws were placed across two synthetic bone blocks fabricated to simulate normal and osteoporotic bone. We compared two groups of normal and osteoporotic blocks for compression achieved and maximal insertional torque generated with fully threaded and partially threaded screw insertion. A micro computed tomography (CT) scan of the composite blocks was obtained to investigate for structural changes created during screw insertion. For both groups, compression was achieved with fully threaded screws and the maximal insertional torque was higher using fully threaded screws. Micro CT analysis demonstrated local bone damage with structural disruption in the near segment of the fully threaded screw path in comparison to the partially threaded. CLINICAL SIGNIFICANCE: this study demonstrates that compression is generated using fully threaded screws without using a predrilled glide hole. The insertional torque required to generate compression with fully threaded screws is increased but is clinically applicable. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1099-1105, 2018.

Finite element analysis of different configurations of fully threaded cannulated screw in the treatment of unstable femoral neck fractures.

BACKGROUND: In the present study, we evaluated the mechanical outcome of different configurations formed by fully threaded screws and partially threaded screws in the treatment of unstable femoral neck fracture. METHODS: The Pauwels type III unstable femoral fracture and the models of the fully threaded screw and partially threaded screw were constructed in 3-matic software and UG-NX software respectively. We then assembled the different screw configurations to the fracture model separately to form the fixation models. After meshing the models' elements, we used Abaqus software to perform the finite element analysis. Parameters of von Mises stress distribution on the screws, peak stress, displacement between fracture fragments, and model principal strains in cancellous bone were reported. RESULTS: Our results indicated that the peak von Mises stresses of screws was concentrated in the middle surface of the screw near the fracture line in each group. Peak stress value of the implants was highest in the model of triangle with posterior single screw. And the lowest stress values were observed in the triangular model. Fully threaded screw in each group underwent the most stress while partially threaded screw underwent a little bit of stress. Lowest displacement was observed in the triangular model. The volume of bone susceptible to yielding in the femoral neck region was the lowest for triangular configuration. CONCLUSIONS: For unstable femoral neck fractures, superior results were obtained by stabilizing the fracture with triangular configuration formed by one superior partially threaded screw and two inferior fully threaded screws. This study will require clinical confirmation as to its practicality in the management of unstable femoral fractures.

Biomechanical properties of a posterior fully threaded positioning screw for cannulated screw fixation of displaced neck of femur fractures.

OBJECTIVES: Displaced intracapsular neck of femur fractures (NOF) in younger patients are usually fixed with partially-threaded cannulated screws. However posterior comminution may lead to construct failure. We hypothesised that a posterior fully threaded positioning screw would enhance stability. METHODS: A total of 16 left composite femora (Sawbone) were used for testing. To mimic a subcapital fracture with posterior comminution, a subcaptial osteotomy was performed and a posterior wedge was resected from the neck. Group A (n=8) was fixed using 3 partially threaded cancellous screws. In Group B (n=8), a fully threaded positioning screw instead of a partially threaded was used posteriorly. The specimens were tested for bending (antero-posterior=A-P) and axial stiffness. Finally, they were axially loaded up to failure or up to 10,000 cycles and the final displacement was measured at the site of the resected neck. More than 5mm of displacement was considered as a failure of the construct. RESULTS: Group B showed significantly higher average A-P stiffness (665±17N/mm compared to 414±41N/mm, p=0.0004); whereas axial stiffness did not significantly differ between the two groups (p=0.301). In Group B, the mean final displacement after cyclic axial loading was 0.51±0.13mm and none of the specimens failed, whereas 7 of 8 constructs failed in Group A (p=0.001). CONCLUSIONS: This biomechanical study points out a potential benefit of replacing the posterior partially threaded cancellous screw with a fully threaded positioning screw in subcapital NOF with posterior comminution. The construct with the fully threaded screw significantly improved the A-P stiffness and reduced the collapse of the fracture.