Mandibular biomechanics rehabilitated with different prosthetic restorations under normal and impact loading scenarios.

BACKGROUND: Restorative treatment options for edentulous patients range from traditional dentures to fixed restorations. The proper selection of materials greatly influences the longevity and stability of fixed restorations. Most prosthetic parts are frequently fabricated from titanium. Ceramics (e.g. zirconia) and polymers (e.g. PEEK and BIOHPP) have recently been included in these fabrications. The mandibular movement produces complex patterns of stress and strain. Mandibular fractures may result from these stresses and strains exceeding the critical limits because of the impact force from falls or accidents. Therefore, it is necessary to evaluate the biomechanical behavior of the edentulous mandible with different restorations under different loading situations. OBJECTIVE: This study analyzes the biomechanical behavior of mandibles after four prosthetic restorations for rehabilitation under normal and impact loading scenarios. MATERIAL AND METHODS: The mandibular model was constructed with a fixed restoration, which was simulated using various materials (e.g. Titanium, Zirconia & BIOHPP), under frontal bite force, maximum intercuspation, and chin impact force. From the extraction of tensile and compressive stresses and strains, as well as the total deformation of mandible segments, the biomechanical behavior and clinical situations were studied. RESULTS: Under frontal bite, the anterior body exhibited the highest tensile (60.34 MPa) and compressive (108.81 MPa) stresses using restoration 4, while the condyles and angles had the lowest tensile (7.12 MPa) and compressive (12.67 MPa) stresses using restoration 3. Under maximum intercuspation, the highest tensile (40.02 MPa) and compressive (98.87 MPa) stresses were generated on the anterior body of the cortical bone using restoration 4. Additionally, the lowest tensile (7.7 MPa) and compressive (10.08 MPa) stresses were generated on the condyles and angles, respectively, using restoration 3. Under chin impact, the highest tensile (374.57 MPa) and compressive (387.3 MPa) stresses were generated on the anterior body using restoration 4. Additionally, the lowest tensile (0.65 MPa) and compressive (0.57 MPa) stresses were generated on the coronoid processes using restoration 3. For all loading scenarios, the anterior body of the mandible had the highest stress and strain values compared with the other segments. Compared to the traditional titanium restoration.2, restoration.1(zirconia) increases the tensile and compressive stresses and strains on the mandibular segments, in contrast to restoration.3 (BIOHPP). In addition, zirconia implants exhibited higher displacements than the other implants. CONCLUSION: In the normal loading scenario, the tensile and compressive stresses and strains on the mandible were within the allowable limits when all restorations were used. Under the chin impact loading scenario, the anterior body of the mandible was damaged by restorations 1 and 4.

[Mandibular condyle localization in orthognathic surgery based on mandibular movement trajectory and its preliminary accuracy verification].

OBJECTIVE: To establish and assess the precision of pre-surgical condyle position planning using mandibular movement trajectory data for orthognathic surgery. METHODS: Skull data from large-field cone beam computed tomography (CBCT) and dental oral scan data were imported into IVSPlan 1.0.25 software for 3D reconstruction and fusion, creating 3D models of the maxilla and mandible. Trajectory data of mandibular movement were collected using a mandibular motion recorder, and the data were integrated with the jaw models within the software. Subsequently, three-dimensional trajectories of the condyle were obtained through matrix transformations, rendering them visually accessible. A senior oral and maxillofacial surgeon with experience in both diagnosis and treatment of temporomandibular joint disease and orthognathic surgery selected the appropriate condyle position using the condyle movement trajectory interface. During surgical design, the mobile mandibular proximal segment was positioned accordingly. Routine orthognathic surgical planning was completed by determining the location of the mandibular distal segment, which was based on occlusal relationships with maxilla and facial aesthetics. A virtual mandible model was created by integrating data from the proximal and distal segment bone. Subsequently, a solid model was generated through rapid prototyping. The titanium plate was pre-shaped on the mandibular model, and the screw hole positions were determined to design a condylar positioning guide device. In accordance with the surgical plan, orthognathic surgery was performed, involving mandibular bilateral sagittal split ramus osteotomy (SSRO). The distal segment of the mandible was correctly aligned intermaxillary, while the proximal bone segment was positioned using the condylar positioning guide device and the pre-shaped titanium plate. The accuracy of this procedure was assessed in a study involving 10 patients with skeletal class Ⅱ malocclusion. Preoperative condyle location planning and intraoperative positioning were executed using the aforementioned techniques. CBCT data were collected both before the surgery and 2 weeks after the procedure, and the root mean square (RMS) distance between the preope-rative design position and the actual postoperative condyle position was analyzed. RESULTS: The RMS of the condyle surface distance measured was (1.59±0.36) mm (95%CI: 1.35-1.70 mm). This value was found to be significantly less than 2 mm threshold recommended by the expert consensus (P < 0.05). CONCLUSION: The mandibular trajectory may play a guiding role in determining the position of the mandibular proximal segment including the condyle in the orthognathic surgery. Through the use of a condylar positioning guide device and pre-shaped titanium plates, the condyle positioning can be personalized and customized with clinically acceptable accuracy.

Digital Workflow in Oral Splint Manufacturing.

AIM: The digital workflow used to manufacture an adjusted oral splint will be demonstrated in a patient case. MATERIALS AND METHODS: A 25-year-old female patient presented for management of her bruxism. Therefore, an adjusted oral splint was manufactured. A computer-aided motion analysis of the patient was conducted (JMA Optic, Amann Girrbach) and full-arch scans of the maxilla and mandible, a biocopy of the maxilla with bite fork as well as buccal scans of the centric jaw relation (Primescan, Dentsply Sirona). The jaw relation was determined beforehand by ballistic closing on a chairside fabricated anterior jig. The digital construction of a Michigan splint took place in the laboratory. The design was nested and milled from a polymethyl methacrylate (PMMA)-containing blank (CLEARsplint Disc, Astron Dental Corporation). RESULT: The oral splint was inserted into the patient's mouth and checked to ensure a tensionfree fit. The static and dynamic contact relationship was checked. During the follow-up visit, the patient reported an improvement in tension in the masticatory muscles. CONCLUSION: The procedure described allows for an adjusted oral splint to be manufactured in a purely digital workflow.

The Effect of Residual Dentition on the Dynamic Adjustment of Wear Facet Morphology on a Mandibular First Molar Crown.

PURPOSE: To evaluate the effect of different residual dentitions on the dynamic adjustment of wear facet morphology on a single mandibular first molar crown with a virtual articulator. MATERIALS AND METHODS: Gypsum casts (N = 12) of natural full dentitions were mounted on an articulator and scanned. The mandibular right first molar (#46) was prepared and a copy of the tooth before it was prepared and used to design the crown. The wear facets on the original #46 were selected and elevated by 0.3 mm in the occlusal direction to generate high points. The #46 with high points was segmented to create a digital wax pattern. Then different teeth were virtually removed to generate 4 types of residual dentitions: Type I (no teeth), Type II (adjacent teeth), Type III (ipsilateral posterior teeth and canine), and Type IV (all teeth). The crowns were adjusted dynamically with different residual teeth to guide mandibular movement of the virtual articulator. Three-dimensional deviations, negative and positive volumes between crowns and wear facets on the original #46 were analyzed. The Kruskal-Wallis test was used to analyze the results. RESULTS: The mean deviation values and positive volumes decreased with the decrease in residual teeth, and the negative volumes showed an opposite trend. The mean deviation values, root mean square, and positive volumes were not significantly different. The negative volume of the crowns of Type I was different from that of Type IV (p = 0.031). CONCLUSIONS: Residual dentition affects the dynamic adjustment of wear facet morphology. When there are insufficient residual teeth, mandibular movements should be accurately measured.

[Method and accuracy of determining the jaw position of repositioning splint with the aid of digital technique].

OBJECTIVE: To establish the workflow of determining the jaw position of repositioning splint with the aid of digital technique, and to evaluate the accuracy of this workflow and compare the accuracy of raising different vertical dimensions in vitro. METHODS: A volunteer was recruited. The data of full-arch scans, cone beam computed tomography (CBCT) image and ultrasonic jaw motion tracking of the volunteer were acquired. The full-arch scans were merged with the CBCT image, which were then matched to the jaw motion tracking reference system. The jaw position of repositioning splint was determined when the anterior teeth opening was 3 mm and the condyle was in centric relation of the fossa in the sagittal plane. A digital repositioning splint was designed in the software based on virtual articulator and fabricated with additive manufacturing technique. After the splint was tried in, another CBCT image was taken and a qualitative analysis was conducted to compare the position of condyle between these two CBCT images. In the in vitro study, standard dental plaster casts with resin ball markers attached to the base were mounted onto a fully adjustable articulator in the intercuspal position. The dental casts were scanned by an extraoral scanner to establish digital models. The ultrasonic jaw motion tracking device was used to obtain simulated jaw movements on the articulator, which was repeated for three times. The digital models and data of jaw movements were merged in one coordination with the aid of bite forks. The jaw position of repositioning splint was determined by adjusting data of jaw movements, each of which was used to determine three vertical jaw positions 4 mm, 5 mm, and 6 mm with the horizontal jaw position of protrusion 2 mm. The virtual articulators with differently adjusted jaw movements were applied in designing repositioning splints, and the final repositioning splints and virtual jaw relationships were exported in STL format. Then the repositioning splints were fabricated with additive manufacturing technique and tried in plaster casts on the mechanical articulator, which were scanned and the jaw relationships on the mechanical articulator were exported later. The virtual jaw relationships and scanned jaw relationships were registered according to lower models and displacement of upper models was calculated. Ball markers were fit to acquire the coordinates of centers and absolute difference values of centers along three coordinating axes X, Y, and Z were calculated. One-way analysis of variance was conducted using SPSS 18.0 software to compare deviations of the three different vertical jaw relationships in two-side test and the significance level was 0.05. RESULTS: With the aid of multi-source data fusion and individualized jaw motion, the clinical workflow of determining jaw position of repositioning splint was preliminarily established. The designed jaw position was realized on the right and the condyle was more inferior than the designed position on the left. Both displacement of the upper models and absolute difference values of centers showed no significant differences (P>0.05) in different vertical jaw dimensions. The displacement of the upper models was (0.25±0.04) mm. The absolute difference values of centers along the three coordinating axes X, Y, and Z were respectively (0.08±0.01) mm, (0.30±0.02) mm, and (0.21±0.04) mm. CONCLUSION: A novel method of determining the jaw position of repositioning splint with the aid of digital technique is established. It is proved to be feasible by try-in after multi-data fusion, computer-aided design and computer-aided manufacturing. As is shown in vitro, it is accurate to apply this method in adjusting jaw position. Further clinical trial will be designed to evaluate its clinical effect.

Evaluation of Mandibular Movement Functions Using Instrumental Ultrasound System.

PURPOSE: The article deals with routinely performed instrumental temporomandibular joint (TMJ) examinations and interpretation of findings obtained from the Arcus Digma ultrasound device in individuals with or without clinical symptoms of temporomandibular disorders (TMD). The aim of this study was to analyze mandibular movement functions and the relationship between incisors and condylar movement parameters during jaw opening, which may be helpful for clinical evaluation in these patients. MATERIALS AND METHODS: The study group consisted of 84 young students with no dental problems and other serious acute or chronic diseases in the medical history; the students were examined both clinically and with the Arcus Digma ultrasound device. RESULTS: Helkimo Di = I was the most common score in 49 participants, and Helkimo Di = II in a significantly (p < 0.01, Di = I vs. Di = II) smaller number of participants. Medical history revealed symptoms of unilateral mastication in 15 participants and a statistically significant increased (p < 0.02, participants with symptoms of unilateral mastication vs. asymptomatic) condylar range of motion parameter during retrusion. Also a significant decrease (p < 0.03, participants with symptoms of unilateral mastication vs. asymptomatic) of the incisal and condylar ranges of motion during mouth opening was found. Limitation of mouth opening, defined as a decrease of inter-incisal distance, appeared in 19 participants (22.6%) and in 25 participants (29.8%) measured instrumentally with the Arcus Digma device. A comparison of instrumental result examinations of the right and left TMJs showed positive correlations of the range of mandible opening movement with the Posselt opening movement (r = 0.75) and opening/closing movements with the Posselt closing movements (r = 0.70). A correlation was demonstrated (r = 0.81) between the condylar range of motion studied on the left and on the right TMJ during mandible opening movement. Correlations were also found between opening-closing movements and the condylar range of motion of the left TMJ, and between the opening-closing movement and the condylar range of motion of the right TMJ during the opening movement. CONCLUSIONS: According to the results of this study with instrumental Arcus Digma ultrasound device measurements of mandibular movements, data were provided on irregularities in TMJ function not detected in participants with or without clinical symptoms of TMD.

Relationship between jaw movement and masticatory performance in adults with natural dentition.

OBJECTIVE: This study determines the relationship between several characteristics of jaw movement and masticatory performance determined by multiple regression analysis and adjusted for occlusal contact area and bite force. MATERIALS AND METHODS: Forty-two young adults with natural dentition participated in this cross-sectional study. Occlusal contact area was determined at the maximum intercuspal position by scanning interocclusal records. Maximum unilateral force was measured by means of a gnathodynamometer. The height and amplitude of mastication, occlusal glide length, lateral guidance angle, anterior-posterior distance and cycle duration were recorded using the ARCUSdigma II system. Masticatory performance was determined by sieving the Optosil particles resulting from 20 chewing cycles. RESULTS: Median particle size was negatively associated with height of mastication, maximum bite force, occlusal contact area and amplitude of mastication. Stepwise multiple linear regression analysis revealed that the height of mastication and dental guidance angle are the characteristics of jaw movement most closely related to masticatory performance. CONCLUSIONS: In adults with natural dentition, a large vertical height of mastication and a small dental guidance angle are the characteristics of jaw movement most closely associated with good masticatory performance, determined by multiple regression analysis and adjusted for occlusal contact area and bite force.

Investigation of the precision of a novel jaw tracking system in recording mandibular movements: A preliminary clinical study.

OBJECTIVES: This preliminary study aimed to clinically assess the precision of a novel optical jaw tracking system (JTS) in registering mandibular movements (MMs) of protrusion and mediotrusion. METHODS: Twenty healthy participants underwent recordings using Cyclops JTS (Itaka Way Med) for functional MMs of protrusion and laterotrusion by two trained clinicians. Each subject performed five registrations at different times according to a standardized pattern within one-month period. The angulations of protrusive and mediotrusive functional paths within the first 2 mm from the maximal intercuspal position (MIP) were calculated for each trace, using a data software for angle measurements. Descriptive statistics were used to assess the repeatability of the recordings for each participant and MM. Additionally, inferential statistics were carried out on standard deviation values obtained (α=0.05). RESULTS: The overall precision for all the patients was 7.07±3.37° for the protrusion angle, 5.24±2.24° for right laterotrusion and 5.14±3.06° for left laterotrusion angles. The protrusion angle ranged from 3.08° to 13.57°, while the right and left laterotrusion ranged from 1.82° to 9.42° and from 1.58° to 10.59°, respectively. No statistically significant differences were observed between different functional MM types and gender (p > 0.05). CONCLUSIONS: Recordings functional MMs of mediotrusion and protrusion using Cyclops JTS showed consistent repeatability, regardless of gender and functional MM type. The results revealed non-negligible variations that may be due to the patients' abilities to precisely reproduce jaw movements or to the operator's ability to consistently connect the kinesiograph. CLINICAL SIGNIFICANCE: Capturing functional MMs digitally and importing the data into dental CAD software is essential for virtual waxing in prosthetic rehabilitations to design a functionalized adapted occlusion. Establishing the repeatability of MM recordings by a JTS is a crucial step in better understanding this novel JTS in the market. This process could facilitate the interpretation of cusp angles, aid in CAD dynamic technical modeling, and enhance clinical data communication between clinicians and technicians in a modern workflow.

Investigation of the accuracy of dynamic condylar position: A model study.

OBJECTIVES: To evaluate dynamic condylar positions by integrating mandibular movement recording data and cone-beam computed tomography (CBCT) and to investigate its accuracy via dynamic model experiments. METHODS: A polyvinyl chloride skull model was utilized. A robot arm was used to operate the mandible to perform mouth opening, closing, protrusion, and lateral movements. A recording device, worn on the skull, was used to record the dynamic process and an optical position tracking (OPT) system was used to simultaneously trace the movements. A self-developed software module was used to evaluate the dynamic condylar position by integrating the dynamic tracing data and a virtual skull model derived from CBCT images. Errors were defined as differences between the dynamic coordinates of six landmarks around the condylar area derived from the software module (test) and OPT system (gold standard). RESULTS: The condylar position errors were 0.76 ± 0.31, 0.55 ± 0.15, and 0.68 ± 0.23 mm for mouth opening, bilateral, and protrusion movements, respectively. Furthermore, the errors for small, moderate, and large mouth opening movements were 0.62 ± 0.19, 0.69 ± 0.29, and 0.94 ± 0.31 mm, respectively. The errors for all movements, except for large mouth opening, were significantly less than 1 mm (P < 0.05). The error was not different from 1 mm in the large mouth opening movement (P > 0.05). CONCLUSIONS: Our developed method of achieving dynamic condylar position by integrating mandibular movement recording data and CBCT images is clinically reliable. CLINICAL SIGNIFICANCE: This study proved the reliability of evaluating dynamic condylar position using a commercial dynamic recording instrument and CBCT images.

Mandibular movement monitor provides faster, yet accurate diagnosis for obstructive sleep apnoea: A randomised controlled study.

Many patients with obstructive sleep apnoea (OSA) remain undiagnosed and thus untreated, and in part this relates to delay in diagnosis. Novel diagnostic strategies may improve access to diagnosis. In a multicentre, randomised study, we evaluated time to treatment decision in patients referred for suspected OSA, comparing a mandibular movement (MM) monitor to respiratory polygraphy, the most commonly used OSA detection method in the UK. Adults with high pre-test probability OSA were recruited from both northern Scotland and London. 40 participants (70 % male, mean±SD age 46.8 ± 12.9 years, BMI 36.9 ± 7.5 kg/m2, ESS 14.9 ± 4.1) wore a MM monitor and respiratory polygraphy simultaneously overnight and were randomised (1:1) to receive their treatment decision based on results from either device. Compared to respiratory polygraphy, MM monitor reduced time to treatment decision by 6 days (median(IQR): 13.5 (7.0-21.5) vs. 19.5 (13.7-35.5) days, P = 0.017) and saved an estimated 29 min of staff time per patient.

Accuracy of a new photometric jaw tracking system in the frontal plane at different recording distances: An in-vitro study.

OBJECTIVES: To evaluate the accuracy of a new photometric jaw tracking system (JTS) in recording linear vertical movements in the frontal plane at different distances. METHODS: A mandibular plaster cast of a patient was placed on a simulation machine capable of linear movements along two spatial axes. Cyclops JTS (Itaka) was adapted to the plaster cast, while the head frame was attached to the simulation machine. The latter performed five linear movements from 20 to 40 mm in the y-axis; each movement was repeated five times at five different recording distance (380 to 420 mm). The recorded movements were measured and compared with those obtained with a laser Doppler vibrometer (LDV) for accuracy analysis. Data were statistically processed (α = 0.05). RESULTS: No statistically significant differences were found between Cyclops and LDV measurements on the y- and z-axes (p = 0.5). Changes in linear vertical motion and distance positions did not affect the accuracy, which remained relatively constant with similar trends and values less than 1 % for each parameter variation. The best condition observed was linear vertical movement of 30 mm at 420 mm (0.010 ± 0.023 mm). CONCLUSIONS: Cyclops has proven to be an accurate JTS in recording linear vertical movements in the frontal plane at different recording distances. For optimal recordings, the scanner should be placed as close as possible to the markers; excessive vertical movements decreased the accuracy. However, this study has limitations and requires in-vivo confirmations. CLINICAL SIGNIFICANCE: The tested JTS proved accurate in recording linear vertical movements in the frontal plane. However, given the limitations of the study, further investigation under real conditions is needed to support prosthetic and gnathological rehabilitations.

Characterization of Mandibular Border Movements and Mastication in Each Skeletal Class Using 3D Electromagnetic Articulography: A Preliminary Study.

Mandibular movement recording is relevant for the planning and evaluation of mandibular function. These movements can include mandibular border movements (MBM) or mastication. Our objective was to characterize the kinematics of MBM and mastication among skeletal classes I, II, and III in the three spatial planes. A descriptive cross-sectional study was conducted with 30 participants. Instructions were provided on how to form Posselt's envelope and to perform masticatory. After data processing, we obtained numerical values for the areas, trajectories, and ranges of MBM that formed Posselt's envelope and the values for speed, masticatory frequency, and the areas of each masticatory cycle. Significant differences were found in the area of Posselt's envelope in the horizontal plane between skeletal classes I and III and in the range of right laterality between skeletal classes II and III. Mastication showed significant differences in the area of the masticatory cycles in the horizontal plane between classes I and III and between classes II and III. In conclusion, there were differences in MBM and mastication between skeletal classes III and I in the horizontal plane. This study supports the need to establish normal values for mandibular kinematics in skeletal class III.

Validity of analysis of masticatory movement using a two-dimensional mandibular movement recording device.

To clarify the validity of analysis of masticatory movement using a two-dimensional (2D) mandibular movement recording device, masticatory movements (pattern of movement path, opening distance, masticatory width, and cycle time) were compared between simultaneous recordings made by 2D and three-dimensional (3D) devices in healthy adults. The 2D device can perform the same level of mandibular movement analysis as the 3D device if the distance between LED and camera is fixed (15 cm), and the findings indicated the suitability of the 2D device for clinical application.

A comparative study based on the mandibular movement track and the movement parameters of the virtual articulator in simulating occlusal adjustment.

OBJECTIVES: This study aimed to compare the effects of virtual adjustment on occlusal interferences in mandibular posterior single crown and three-unit bridge restorations by using the mandibular movement track and the movement parameters of a virtual articulator. METHODS: Twenty-two participants were recruited. Digital casts of the maxillary and mandibular arches were obtained using an intraoral scanner, and the jaw registration system was used to record the data of the mandibular movement track and the movement parameters of the articulator. Four kinds of restorations with 0.3 mm occlusal interferences were designed with dental design software. In particular, single crowns were designed for teeth 44 and 46, whereas three-unit bridges were designed for teeth 44-46 and 45-47, and the corresponding natural teeth were virtually extracted. Virtual adjustment of the restorations was performed using two dynamic occlusal recordings, namely, the mandibular movement track and the movement parameters of the virtual articulator. A reverse-engineering software was used to measure the root-mean-square of the three-dimensional deviation of the occlusal surfaces between natural teeth and the adjusted restorations. The differences between the two methods of virtual-occlusion adjustment were compared and analyzed. RESULTS: For the same group of restorations, the three-dimensional deviation of the mandibular movement track group were lower than those of the virtual articulator group, and the differences were statistically significant (P<0.05). For the four groups of restorations adjusted by the same method, the three-dimensional deviation of the 46-tooth single crown was the largest and the smallest three-dimensional deviation was that of the 44-tooth single crown. Statistical differences existed between the 44-tooth single crown and the other groups (P<0.05). CONCLUSIONS: For the occlusal design of posterior single crown and three-unit bridge, the mandibular movement track could be a more effective approach to virtual occlusal adjustment than the movement parameters of the virtual articulator.

Comparative study of normal condyle and temporomandibular joint prosthesis movement during mouth opening by dynamic magnetic resonance imaging and computed tomography.

Background: To analyze and compare the trajectory of condylar motion during mouth opening in normal volunteers and patients after total joint replacement (TJR) of the temporomandibular joint (TMJ). Methods: Condylar movement during mouth opening was recorded by dynamic magnetic resonance imaging (MRI) for volunteers with normal TMJs and dynamic computed tomography (CT) for patients after TMJ TJR. Trajectories of the points selected every 5 mm from the superior point of the condyle (P0) along its axis to the mandibular angle (P-25) were recorded. The arc length and curvature radius of average trajectories for each point were calculated and compared between the normal joints and TJRs, especially P-10 which is the corresponding point of the prosthesis apex without lateral pterygoid muscle (LPM) attachment at the normal joint with LPM attachment. The location of the point with the most similar trajectory was identified in the normal joints and compared with the condylar prosthesis. Results: A total of 9 volunteers with 18 normal TMJs, and 5 patients with 6 prostheses were included in this study. For normal TMJs, the average condylar trajectories during mouth opening were a concave upward curve. Meanwhile, the trajectories of contralateral normal joints in patients with unilateral TJR and all condylar prostheses were significantly decreased. The arc length and curvature radius of average trajectories gradually decreased from P0. In the normal joints, P-20 had the most similar trajectories with the average arc lengths and a curvature radius of 13.0/4.2 mm. In P-10, the average arc lengths and curvature radius of the normal cases, natural TMJ of the unilateral replacement patients, prosthetic TMJ of the unilateral replacement patients, and prosthetic TMJ of the bilateral replacement patient, were 15.6/6.6 mm, 13.1/4.9 mm, 4.7/4.4 mm, and 6.4/5.8 mm, respectively. Conclusions: P-20 in the normal joint exhibited the most similar trajectory among individuals. The trajectory difference between the prosthesis apex without LPM attachment and the corresponding point at the normal joint with LPM attachment provides a reference for fossa prosthesis functional surface design.

Designing customized temporomandibular fossa prosthesis based on envelope surface of condyle movement: validation via in silico musculoskeletal simulation.

Objective: This study presents an innovative articular fossa prosthesis generated by the envelope surface of condyle movement, and compares its mandible movements, muscle activities, and joint reaction forces with two temporomandibular joint (TMJ) prostheses using multibody musculoskeletal simulation. Methods: A healthy 23-year-old female was recruited for this study. Cone-beam computed tomographic (CBCT) was performed to reconstruct the mandibular bone geometry. A customized TMJ fossa prosthesis was designed based on the subject-specific envelope surface of condyle movement (ESCM). Mandibular kinematics and jaw-closing muscle electromyography (EMG) were simultaneously recorded during maximum jaw opening-closing movements. To validate our prosthesis design, a mandibular musculoskeletal model was established using flexible multibody dynamics and the obtained kinematics and EMG data. The Biomet fossa prosthesis and the ellipsoidal fossa prosthesis designed by imitating the lower limb prostheses were used for comparison. Simulations were performed to analyze the effects of different fossa prostheses on jaw opening-closing motions, mandibular muscle activation, and contact forces. Results: The maximum opening displacement for the envelope-based fossa prosthesis was greater than those for Biomet and ellipsoidal prostheses (36 mm, 35 mm, and 33 mm, respectively). The mandibular musculoskeletal model with ellipsoidal prosthesis led to dislocation near maximal jaw opening. Compared to Biomet, the envelope-based fossa reduced the digastric and lateral pterygoid activation at maximal jaw opening. It also reduced the maximal resistance to condylar sliding on the intact side by 63.2 N. Conclusion: A customized TMJ fossa prosthesis was successfully developed using the ESCM concept. Our study of musculoskeletal multibody modeling has highlighted its advantages and potential. The artificial fossa design successfully achieved a wider condylar range of motion. It also reduced the activation of jaw opening muscles on the affected side and resistance on the intact side. This study showed that an ESCM-based approach may be useful for optimizing TMJ fossa prostheses design.

Clinical validation of a mandibular movement signal based system for the diagnosis of pediatric sleep apnea.

BACKGROUND: Given the high prevalence and risk for outcomes associated with pediatric obstructive sleep apnea (OSA), there is a need for simplified diagnostic approaches. A prospective study in 140 children undergoing in-laboratory polysomnography (PSG) evaluates the accuracy of a recently developed system (Sunrise) to estimate respiratory efforts by monitoring sleep mandibular movements (MM) for the diagnosis of OSA (Sunrise™). METHODS: Diagnosis and severity were defined by an obstructive apnea/hypopnea index (OAHI) ≥ 1 (mild), ≥ 5 (moderate), and ≥ 10 events/h (severe). Agreement between PSG and Sunrise™ was assessed by Bland-Altman method comparing respiratory disturbances hourly index (RDI) (obstructive apneas, hypopneas, and respiratory effort-related arousals) during PSG (PSG_RDI), and Sunrise RDI (Sr_RDI). Performance of Sr_RDI was determined via ROC curves evaluating the device sensitivity and specificity at PSG_OAHI ≥ 1, 5, and 15 events/h. RESULTS: A median difference of 1.57 events/h, 95% confidence interval: -2.49 to 8.11 was found between Sr_RDI and PSG_RDI. Areas under the ROC curves of Sr_RDI were 0.75 (interquartile range [IQR]: 0.72-0.78), 0.90 (IQR: 0.86-0.92) and 0.95 (IQR: 0.90-0.99) for detecting children with PSG_OAHI ≥ 1, PSG_OAHI ≥ 5, or PSG_ OAHI ≥ 10, respectively. CONCLUSION: MM automated analysis shows significant promise to diagnose moderate-to-severe pediatric OSA.

Epidemiology of Respiration with Mandibular Movement in Advanced Cancer Patients: A Multicenter Prospective Cohort Study.

Background: Respiration with mandibular movement (RMM) is one of the important clinical signs of impending death. However, there is very limited data on its natural course. Objective and Methods: This study was conducted in 23 inpatient palliative care units in Japan. It aimed to explore the natural course of RMM. Results: Among a total of 1526 cancer patients included, 1065 patients (69.8%) had RMM. A total of 14.8% patients experienced respiratory arrest within 30 minutes from RMM onset, 14.3% within 30-60 minutes, 34.4% within 1-4 hours, 17.5% within 4-12 hours, 8.9% within 12-24 hours, and 10.4%> 24 hours. Mean oxygen saturation and percentage of patients with SpO2 ≥90% at RMM onset were found to be significantly higher in patients with longer durations from RMM onset to death (p < 0.001). Conclusion: RMM occurred in a majority (80%) of dying patients within 12 hours. A minority of the patients survived >24 hours.

CPG-based generation strategy of variable rhythmic chewing movements for a dental testing chewing robot.

The rhythmic chewing movement pattern is dynamically reshaped to adapt to a variable chewing environment. The variance affects the wear performance of dental prostheses. This study was aimed to generate these variable rhythmic chewing movements for dental testing equipment. A six-axis parallel chewing robot DUT-2 was adopted as the dental testing equipment. Four variances were extracted from the rhythmic movement, including period, offset, amplitude, and mode. The relevant movement cases, including gradually accelerating movement, gradually increasing movement, gradually shrinking movement, and bilateral movement, were designed. Then, a central pattern generator (CPG) model based on morphed phase oscillators was proposed. According to the coupling feature of the rhythmic movements, the specific modulation method of the CPG model was provided for these movements. The simulated incisor trajectory was outputted by importing the driving amplitudes from the CPG model to the virtual prototype of the chewing robot. The bite force (considering two-body and three-body contacts) was analyzed by writing the driving amplitudes into the motion controller of the chewing robot's physical prototype. The relative errors of offset and amplitude in the z-direction were 4.14% and 0.74%, respectively. The transition was smooth around the turning point during the gradually increasing movement and bilateral movement. For two-body contact, the average relative error and bias of the maximum bite force were 4.15% and 1.08%, respectively. The food involvement decreased the accuracies to 13.18% and 2.50%, respectively. The CPG model supplies a bionic and explicit approach for generating the variable rhythmic chewing movements. The variable movements related to chewing preferences and food properties could be replicated. Besides, the high repeatability of the maximum bite force is beneficial for running the repetitive wear tests. Finally, the CPG model makes it possible to study the influence of the variance on wear performance.

Does Orthodontic Treatment Change the Preferred Chewing Side of Patients with Malocclusion?

Whether orthodontic treatment can change the preferred chewing side (PCS) is unknown. This study examined (1) if the PCS changes after orthodontic treatment and (2) which factors contribute to this change. Two hundred fifty patients who visited the orthodontic clinic at Tokyo Medical and Dental University Hospital between 2017 and 2020 were included in the study. Mandibular kinesiograph (MKG) was taken at pre- and post-treatment, and PCS was determined. Patients who showed a change in PCS to the opposite side and those who showed no change in PCS at post-treatment were pooled into the PCS-changed and PCS-unchanged groups, respectively. The demographic, clinical, and cephalometric parameters were compared between the groups. Significant factors associated with changes in were of age < 20 years at the beginning of orthodontic treatment (odds ratio (OR), 2.00), maximum lateral mandibular movement to PCS ≥ 10.0 mm at pre-treatment (OR, 6.51), and change in occlusal canting of ≥1.0° (OR, 2.72). The predicted probability of change in PCS was 13.2%, 36.0%, and 67.5% for no factor, one factor, and two factors associated with PCS change, respectively. Orthodontic treatment may change PCS due to patient age, maximum lateral mandibular movement to PCS, and change in occlusal canting.