High-Performance Monolithic 3D Integrated Complementary Inverters Based on Monolayer n-MoS2 and p-WSe2.

Herein, the structure of integrated M3D inverters are successfully demonstrated where a chemical vapor deposition (CVD) synthesized monolayer WSe2 p-type nanosheet FET is vertically integrated on top of CVD synthesized monolayer MoS2 n-type film FET arrays (2.5 × 2.5 cm) by semiconductor industry techniques, such as transfer, e-beam evaporation (EBV), and plasma etching processes. A low temperature (below 250 °C) is employed to protect the WSe2 and MoS2 channel materials from thermal decomposition during the whole fabrication process. The MoS2 NMOS and WSe2 PMOS device fabricated show an on/off current ratio exceeding 106 and the integrated M3D inverters indicate an average voltage gain of ≈9 at VDD = 2 V. In addition, the integrated M3D inverter demonstrates an ultra-low power consumption of 0.112 nW at a VDD of 1 V. Statistical analysis of the fabricated inverters devices shows their high reliability, rendering them suitable for large-area applications. The successful demonstration of M3D inverters based on large-scale 2D monolayer TMDs indicate their high potential for advancing the application of 2D TMDs in future integrated circuits.

The Role of Luminescent Coupling in Monolithic Perovskite/Silicon Tandem Solar Cells.

Luminescent coupling (LC) is a key phenomenon in monolithic tandem solar cells. This study presents a nondestructive technique to quantitatively evaluate the LC effect, addressing a gap in the existing predictions made by optical modeling. The method involves measuring the ratio of photons emitted from the high bandgap top cell that escape through the rear, contributing additional current to the bottom cell, and to those escaping from the front side of top cell. The findings indicate that in the analyzed monolithic perovskite/silicon tandem solar cells, more than 85% of the emitted photons escaping from the perovskite top cell are used to generate additional current in the bottom cell. This process notably reduces the mismatch in the generated current between each subcell, particularly when the current is limited by the low bandgap subcell. The presented method is applicable to a variety of monolithic tandem structures, providing vital information for subcell characterization, providing vital information for predicting energy output and optimization for outdoor applications.

Electrochemically Dealloying Engineering toward Integrated Monolithic Electrodes with Superior Electrochemical Li-Storage Properties.

Integrated monolithic electrodes (IMEs) free of inactive components demonstrate great potential in boosting energy-power densities and cycling life of lithium-ion batteries. However, their practical applications are significantly limited by low active substance loading (< 4.0 mg cm-2 and 1.0 g cm-3), complicated manufacturing process, and high fabrication cost. Herein, employing industrial Cu-Mn alloy foil as a precursor, a simple neutral salt solution-mediated electrochemical dealloying strategy is proposed to address such problems. The resultant Cu-Mn IMEs achieve not only a significantly larger active material loading due to the in situ generated Cu2O and MnOx (ca. 16.0 mg cm-2 and 1.78 g cm-3), simultaneously fast transport of ions and electrons due to the well-formed nanoporous structure and built-in Cu current collector, but also high structural stability due to the interconnected ligaments and suitable free space to relieve the volume expansion upon lithiation. As a result, they demonstrate remarkable performances including large specific capacities (> 5.7 mAh cm-2), remarkable pseudocapacitive effect despite the battery-type constitutes, long cycling life, and good working condition in a lithium-ion full cell. This study sheds new light on the further development of IMEs, enriches the existing dealloying techniques, and builds a bridge between the two.

Monolithic Microparticles Facilitated Flower-Like TiO2 Nanowires for High Areal Capacity Flexible Li-Ion Batteries.

Flexible lithium-ion batteries (FLIBs) are intensively studied using free-standing transition metal oxides (TMOs)-based anode materials. However, achieving high areal capacity TMO-based anode materials is yet to be effectively elucidated owing to the poor adhesion of the active materials to the flexible substrate resulting in low active mass loading, and hence low areal capacity is realized. Herein, a novel monolithic rutile TiO2 microparticles on carbon cloth (ATO/CC) that facilitate the flower-like arrangement of TiO2 nanowires (denoted ATO/CC/OTO) is demonstrated as high areal capacity anode for FLIBs. The optimized ATO/CC/OTO anode exhibits high areal capacity (5.02 mAh cm-2@0.4 mA cm-2) excellent rate capability (1.17 mAh cm-2@5.0 mA cm-2) and remarkable cyclic stability (over 500 cycles). A series of morphological, kinetic, electrochemical, in situ Raman, and theoretical analyses reveal that the rational phase boundaries between the microparticles and nanowires contribute to promoting the Li storage activity. Furthermore, a 16.0 cm2 all-FLIB pouch cell assembled based on the ATO/CC/OTO anode and LiNiCoMnO2 cathode coated on ATO/CC (ATO/CC/LNCM) exhibits impressive flexibility under different folding conditions, creating opportunity for the development of high areal capacity anodes in future flexible energy storage devices.

Using the reactive/transport dispersive models to simulate a monolithic anion exchanger: Experimental parameter determination, simultaneous model evaluation, and validation.

Selecting an adequate model to represent the mass transfer mechanisms occurring in a chromatographic process is generally complicated, which is one of the reasons why monolithic chromatography is scarcely simulated. In this study, the chromatographic separation of model proteins bovine serum albumin (BSA), ß-lactoglobulin-A, and ß-lactoglobulin-B on an anion exchange monolith was simulated based on experimental parameter determination, simultaneous model testing, and validation under three statistical criteria: retention time, dispersion accuracies, and Pearson correlation coefficient. Experimental characterization of morphologic, physicochemical, and kinetic parameters was performed through volume balances, pressure drop analysis, breakthrough curve analysis, and batch adsorptions. Free Gibbs energy indicated a spontaneous adsorption process for proteins and counterions. Dimensionless numbers were estimated based on height equivalent to a theoretical plate analysis, finding that pore diffusion controlled ß-lactoglobulin separation, whereas adsorption/desorption kinetics was the dominant mechanism for BSA. The elution profiles were modeled using the transport dispersive model and the reactive dispersive model coupled with steric mass action (SMA) isotherms because these models allowed to consider most of the mass transport mechanisms that have been described. RDM-SMA presented the most accurate simulations at pH 6.0 and at low (250 mM) and high (400 mM) NaCl concentrations. This simulation will be used as reference to forecast the purification of these proteins from bovine whey waste and to extrapolate this methodology to other monolith-based separations using these three statistical criteria that have not been used previously for this purpose.

Graphitized Carbon-Supported Co@Co3O4 for Ozone Decomposition over the Entire Humidity Range.

Ground-level ozone (O3) pollution has emerged as a significant concern due to its detrimental effects on human health and the ecosystem. Catalytic removal of O3 has proven to be the most efficient and cost-effective method. However, its practical application faces substantial challenges, particularly in relation to its effectiveness across the entire humidity range. Herein, we proposed a novel strategy termed "dual active sites" by employing graphitized carbon-loaded core-shell cobalt catalysts (Co@Co3O4-C). Co@Co3O4-C was synthesized via the pyrolysis of a Co-organic ligand as the precursor. By utilizing this approach, we achieved a nearly constant 100% working efficiency of the Co@Co3O4-C catalyst for catalyzing O3 decomposition across the entire humidity range. Physicochemical characterization coupled with density functional theory calculations elucidates that the presence of encapsulated metallic Co nanoparticles enhances the reactivity of the cobalt oxide capping layer. Additionally, the interface carbon atom, strongly influenced by adjacent metallic Co nuclei, functions as a secondary active site for the decomposition of O3 decomposition. The utilization of dual active sites effectively mitigates the competitive adsorption of H2O molecules, thus isolating them for adsorption in the cobalt oxide capping layer. This optimized configuration allows for the decomposition of O3 without interference from moisture. Furthermore, O3 decomposition monolithic catalysts were synthesized using a material extrusion-based three-dimensional (3D) printing technology, which demonstrated a low pressure drop and exceptional mechanical strength. This work provides a "dual active site" strategy for the O3 decomposition reaction, realizing O3 catalytic decomposition over the entire humidity range.

Monolithic Catalyst of Ni Foam-Supported MnOx for Boosting Magnetocaloric Oxidation of Toluene.

Catalytic oxidation has been considered an effective technique for volatile organic compound degradation. Development of metal foam-based monolithic catalysts coupling electromagnetic induction heating (EMIH) with efficiency and low energy is critical yet challenging in industrial applications. Herein, a Mn18.2-NF monolithic catalyst prepared by electrodeposition exhibited superior toluene catalytic activity under EMIH conditions, and the temperature of 90% toluene conversion decreased by 89 °C compared to that in resistance furnace heating. Relevant characterizations proved that the skin effect induced by EMIH encouraged activation of gaseous oxygen, leading to superior low-temperature redox properties of Mn18.2-NF under the EMIH condition. In situ Fourier transform infrared spectroscopy results showed that skin effect-induced activation of oxidizing species further accelerated the conversion of intermediates. As a result, the Mn18.2-NF monolithic catalyst under EMIH demonstrated remarkable performance for the toluene oxidation, surpassing the conventional nonprecious metal catalyst and other reported monolithic catalysts.

Enhancing Oxygen Activation Ability by Composite Interface Construction over a 2D Co3O4-Based Monolithic Catalyst for Toluene Oxidation.

Developing robust metal-based monolithic catalysts with efficient oxygen activation capacity is crucial for thermal catalytic treatment of volatile organic compound (VOC) pollution. Two-dimensional (2D) metal oxides are alternative thermal catalysts, but their traditional loading strategies on carriers still face challenges in practical applications. Herein, we propose a novel in situ molten salt-loading strategy that synchronously enables the construction of 2D Co3O4 and its growth on Fe foam for the first time to yield a unique monolithic catalyst named Co3O4/Fe-S. Compared to the Co3O4 nanocube-loaded Fe foam, Co3O4/Fe-S exhibits a significantly improved catalytic performance with a temperature reduction of 44 °C at 90% toluene conversion. Aberration-corrected scanning transmission electron microscopy and theoretical calculation suggest that Co3O4/Fe-S possesses abundant 2D Co3O4/Fe3O4 composite interfaces, which promote the construction of active sites (oxygen vacancy and Co3+) to boost oxygen activation and toluene chemisorption, thereby accelerating the transformation of reaction intermediates through Langmuir-Hinshelwood (L-H) and Mars-van Krevelen (MvK) mechanisms. Moreover, the growth mechanism reveals that 2D Co3O4/Fe3O4 composite interfaces are generated in situ in molten salt, inducing the growth of 2D Co3O4 onto the surface lattice of 2D Fe3O4. This study provides new insights into enhancing oxygen activation and opens an unprecedented avenue in preparing efficient monolithic catalysts for VOC oxidation.

Study of the Enantioselectivity and Recognition Mechanism of Allyl-ß-CD Modified Organic Polymer Monolithic Capillary Column.

Allyl-ß-CD was synthesized and used as the chiral functional monomer to prepare chiral organic polymer monolithic columns in capillary HPLC. First, the enantioselectivity of the prepared allyl-ß-CD modified organic polymer monolithic capillary columns was investigated. Then, the influences of enantioseparation conditions of chiral drugs were further explored. Finally, the recognition mechanism was studied by molecular docking with AutoDock. Complete enantioseparations of four chiral drugs as well as partial enantioseparations of eight chiral drugs have been achieved. Results showed that the RSD values for run-to-run, day-to-day, and column-to-column variations ranged from 1.2% to 4.6%, 1.4% to 4.7%, and 2.0% to 6.1%, respectively. The enantioselectivity factor rather than resolution is correlated with the binding free energy difference between enantiomers with allyl-ß-CD. Furthermore, the abundant ether bonds, hydroxyl groups, and hydrophobic cavities in cyclodextrin are responsible for the enantioseparation ability of the chiral monolithic capillary columns.

Clinical performance and risk factors of all-ceramic screw-retained implant crowns in the posterior region based on a retrospective investigation.

OBJECTIVES: Clinical data on all-ceramic screw-retained implant crowns (SICs) luted on titanium base abutments (TBAs) over more than 3 years are sparse. This study aimed to evaluate the clinical performance and potential risk factors for these restorations. MATERIALS AND METHODS: Analysis took place based on the medical patient-records of three dental offices. Implant survival and prosthetic complications over time were evaluated. The study included SICs in premolar and molar regions made from monolithic lithium disilicate ceramic (M_LiDi) or veneered zirconia (V_ZiO) luted on a TBA documented over an observation time of at least 3 years. Survival and complication rates were calculated and compared by a log-rank test. Cox-Regressions were used to check potential predictors for the survival (p < .05). RESULTS: Six hundred and one crowns out of 371 patients met the inclusion criteria and follow-up period was between 3.0 and 12.9 (mean: 6.4 (SD: 2.1)) years. Over time, six implants had to be removed and 16 restorations had to be refabricated. The estimated survival rates over 10 years were 93.5% for M_LiDi and 95.9% for V_ZiO and did not differ significantly among each other (p = .80). However, V_ZiO showed significantly higher complication rates (p = .003). Material selection, sex, age, and implant diameter did not affect the survival of investigated SICs but crown height influences significantly the survival rate (hazard ratio, HR = 1.26 (95%CI: 1.08, 1.49); p = .043). CONCLUSIONS: Screw-retained SICs luted on TBAs that were fabricated from monolithic lithium disilicate ceramic or veneered zirconia showed reliable and similar survival rates. Increasing crown heights reduced survival over the years.

Digital light processing 3D printing of microfluidic devices targeting high-pressure liquid-phase separations.

This paper focuses on 3D printing using digital light processing (DLP) to create microchannel devices with inner diameters of 100, 200, and 500 µm and cater flow-through applications within the realm of analytical chemistry, in particular high-pressure liquid chromatographic separations. Effects of layer thickness and exposure time on channel dimensions and surface roughness were systematically investigated. Utilizing a commercially accessible 3D printer and acrylate resin formulation, we fabricated 100-500 µm i.d. squared and circular channel designs minimizing average surface roughness (< 20%) by applying a 20-µm layer thickness and exposure times ranging from 1.1 to 0.7 s. Pressure resistance was measured by encasing microdevices in an aluminum chip holder that integrated flat-bottom polyetheretherketon (PEEK) nanoports allowing to establish the micro-to-macro interface to the HPLC instrument. After thermal post-curing and finetuning the clamping force of the chip holder, a maximum pressure resistance of 650 bar (1.5% RSD) was reached (n = 3). A polymer monolithic support structure was successfully synthesized in situ with the confines of a 500 µm i.d. 3D printed microchannel. A proof-of-concept of a reversed-phase chromatographic gradient separation of intact proteins is demonstrated using an aqueous-organic mobile-phase with isopropanol as organic modifier.

A new approach towards highly sensitive detection of endogenous N-acetylaspartic acid, N-acetylglutamic acid, and N-acetylaspartylglutamic acid in brain tissues based on strong anion exchange monolith microextraction coupled with UHPLC-MS/MS.

A novel in-tube solid-phase microextraction coupled with an ultra-high performance liquid chromatography-mass spectrometry method has been established for simultaneous quantification of three crucial brain biomarkers N-acetylaspartic acid (NAA), N-acetylglutamic acid (NAG), and N-acetylaspartylglutamic acid (NAAG). A polymer monolith with quaternary ammonium as the functional group was designed and exhibited efficient enrichment of target analytes through strong anion exchange interaction. Under the optimized conditions, the proposed method displayed wide linear ranges (0.1-80 nM for NAA and NAG, 0.2-160 nM for NAAG) with good precision (RSDs were lower than 15%) and low limits of detection (0.019-0.052 nM), which is by far the most sensitive approach for NAA, NAG, and NAAG determination. Furthermore, this approach has been applied to measure the target analytes in mouse brain samples, and endogenous NAA, NAG, and NAAG were successfully detected and quantified from only around 5 mg of cerebral cortex, cerebellum, and hippocampus. Compared with existing methods, the newly developed method in the current study provides highest sensitivity and lowest sample consumption for NAA, NAG, and NAAG measurements, which would potentially be utilized in determining and tracking these meaningful brain biomarkers in diseases or treatment processes, benefiting the investigations of pathophysiology and treatment of brain disorders.

Initial damage and failure load of zirconia-ceramic and metal-ceramic posterior cantilever fixed partial dentures.

OBJECTIVES: The aim of this study was to compare failure load and initial damage in monolithic, partially veneered, and completely veneered (translucent) zirconia cantilevered fixed partial dentures (CFPDs), as well as completely veneered metal-ceramic CFPDs under different support and loading configurations. MATERIALS AND METHODS: Eight test groups with anatomically congruent CFPDs (n = 8/group) were fabricated, differing in CFPD material/support structure/loading direction (load applied via steel ball (Ø 6 mm) 3 mm from the distal end of the pontic for axial loading with a 2-point contact on the inner cusp ridges of the buccal and oral cusps and 1.3 mm below the oral cusp tip for 30° oblique loading): (1) monolithic zirconia/CoCr abutment teeth/axial, (2) monolithic zirconia/CoCr abutment teeth/oblique, (3) partially veneered zirconia/CoCr abutment teeth/axial, (4) partially veneered zirconia/CoCr abutment teeth/oblique, (5) completely veneered zirconia/CoCr abutment teeth/axial, (6) completely veneered CoCr/CoCr abutment teeth/axial (control group), (7) partially veneered zirconia/implants/axial, and (8) partially veneered zirconia/natural teeth/axial. Restorations were artificially aged before failure testing. Statistical analysis was conducted using one-way ANOVA and Tukey post hoc tests. RESULTS: Mean failure loads ranged from 392 N (group 8) to 1181 N (group 1). Axially loaded monolithic zirconia CFPDs (group 1) and controls (group 6) showed significantly higher failure loads. Oblique loading significantly reduced failure loads for monolithic zirconia CFPDs (group 2). Initial damage was observed in all groups except monolithic zirconia groups, and fractography revealed design flaws (sharp edges at the occlusal boundary of the veneering window) in partially veneered zirconia CFPDs. CONCLUSIONS: Monolithic zirconia CFPDs might be a viable alternative to completely veneered CoCr CFPDs in terms of fracture load. However, oblique loading of monolithic zirconia CFPDs should be avoided in clinical scenarios. Design improvements are required for partially veneered zirconia CFPDs to enhance their load-bearing capacity. CLINICAL RELEVANCE: Monolithic zirconia may represent a viable all-ceramic alternative to the established metal-ceramic option for CFPD fabrication. However, in daily clinical practice, careful occlusal adjustment and regular monitoring should ensure that oblique loading of the cantilever is avoided.

Design and Evaluation of a Rapid Monolithic Manufacturing Technique for a Novel Vision-Based Tactile Sensor: C-Sight.

Tactile sensing has become indispensable for contact-rich dynamic robotic manipulation tasks. It provides robots with a better understanding of the physical environment, which is a vital supplement to robotic vision perception. Compared with other existing tactile sensors, vision-based tactile sensors (VBTSs) stand out for augmenting the tactile perception capabilities of robotic systems, owing to superior spatial resolution and cost-effectiveness. Despite their advantages, VBTS production faces challenges due to the lack of standardised manufacturing techniques and heavy reliance on manual labour. This limitation impedes scalability and widespread adoption. This paper introduces a rapid monolithic manufacturing technique and evaluates its performance quantitatively. We further develop and assess C-Sight, a novel VBTS sensor manufactured using this technique, focusing on its tactile reconstruction capabilities. Experimental results demonstrate that the monolithic manufacturing technique enhances VBTS production efficiency significantly. Also, the fabricated C-Sight sensor exhibits its reliable tactile perception and reconstruction capabilities, proofing the validity and feasibility of the monolithic manufacturing method.

Differential BroadBand (1-16 GHz) MMIC GaAs mHEMT Low-Noise Amplifier for Radio Astronomy Applications and Sensing.

A broadband differential-MMIC low-noise amplifier (DLNA) using metamorphic high-electron-mobility transistors of 70 nm in Gallium Arsenide (70 nm GaAs mHEMT technology) is presented. The design and results of the performance measurements of the DLNA in the frequency band from 1 to 16 GHz are shown, with a high dynamic range, and a noise figure (NF) below 1.3 dB is obtained. In this work, two low-noise amplifiers (LNAs) were designed and manufactured in the OMMIC foundry: a dual LNA, which we call balanced, and a differential LNA, which we call DLNA. However, the paper focuses primarily on DLNA because of its differential architecture. Both use a 70 nm GaAs mHEMT space-qualified technology with a cutoff frequency of 300 GHz. With a low power bias Vbias/Ibias (5 V/40.5 mA), NF < 1.07 dB "on wafer" was achieved, from 2 to 16 GHz; while with the measurements made "on jig", NF = 1.1 dB, from 1 to 10 GHz. Furthermore, it was obtained that NF < 1.5 dB, from 1 to 16 GHz, with a figure of merit equal to 145.5 GHz/mW. Finally, with the proposed topology, several LNAs were designed and manufactured, both in the OMMIC process and in other foundries with other processes, such as UMS. The experimental results showed that the NF of the DLNA MMIC with multioctave bandwidth that was built in the frequency range of the L-, S-, C-, and X-bands was satisfactory.

Finite element evaluation of dentin stress changes following different endodontic surgical approaches.

The aim was to compare the effect of different endodontic surgical treatments on the stress distributions in dentin of a simulated first mandibular molar tooth using the finite element analysis method. Three surgical endodontic procedures (apical resection, root amputation, and hemisection) were simulated in a first mandibular molar. Biodentine or mineral-trioxide-aggregate was used to repair the surgery site in apical resection and root amputation models; the remaining root canal spaces were filled with gutta-percha. Access cavities were restored using resin composite. In hemisection model, root canal was filled with gutta-percha, and coronal restoration was finished with a monolithic zirconia crown. A sound tooth model was created as a control model. An oblique force of 300 N angled at 45° to the occlusal plane was simulated. Maximum von Mises stresses were evaluated in dentin near the surgery regions and the entire tooth. Apical resection/Biodentine and apical resection/mineral-trioxide-aggregate models generated maximum von Mises stresses of 39.001 MPa and 39.106 MPa, respectively. The recorded maximum von Mises stresses in root amputation models were 66.491 MPa for root amputation/Biodentine and 73.063 MPa for root amputation/mineral-trioxide-aggregate models. The highest maximum von Mises stress value among all models was observed in the hemisection model, measuring 138.87 MPa. Hemisection induced the highest von Mises stresses in dentin, followed by root amputation and apical resection. In apical resection, Biodentine and mineral-trioxide-aggregate did not show a significant difference in stress distribution. Biodentine in root amputation may lead to lower stresses compared to mineral-trioxide-aggregate.

CAD/CAM full-mouth rehabilitation of an elderly patient: One-piece digital complete denture meets multilayered zirconia with gradient technology.

OBJECTIVE: This article highlights a CAD/CAM complete-mouth rehabilitation in an 82-year-old patient by means of a complete maxillary prosthesis and mandibular implant- and tooth-supported fixed restorations made from multilayered zirconia. CLINICAL CONSIDERATIONS: Comprehensive complete-mouth rehabilitations in elderly patients with adaptation of the occlusal vertical dimension (OVD) often present particular challenges. This applies especially when exacting functional and esthetic requirements are to be met and the treatment should not cause the patient too much effort, still ensuring the highest level of quality and efficiency and a low intervention rate. CONCLUSION: The digital approach used for the present patient allowed for an efficient treatment procedure, facilitated virtual evaluations using a face-scan, and enhanced the predictability of the prosthodontic outcome. The approach enabled some steps required in the conventional protocol to be omitted, resulting in a straightforward clinical treatment with minimal strain on the patient. CLINICAL SIGNIFICANCE: Because of the comprehensive recording of extraoral and intraoral data, for example with a facial scanner, it was possible to transfer a digital replica of the patient to the dental laboratory technician. With this protocol, many steps can be performed in the absence of the real patient.

A step-by-step technique to create an ideal color match, form, and surface texture to all-ceramic restorations.

OBJECTIVES: Although the presence of a chairside CAD/CAM system in the dental office saves time and cost, it deprives the dentist from the dental technologist' skills and experience. The dentist now has to gain and acquire knowledge and skills about how to finish, characterize, stain, and glaze ceramic restorations. The main objectives of this article is to teach novel and reproducible techniques for surface color, texture, glaze and polish for either the chairside or laboratory fabricated indirect ceramic restoration. CLINICAL CONSIDERATIONS: A protocol for intraoral characterization of monolithic ceramics; the "Triple R" protocol for tooth color mimicking was followed. It consist of three steps: (1) "Recognize" tooth color shapes, (2) "Record" the present color shapes in the patient dentition by drawing a color map for the color shapes extension and determine which luster paste stain to be used for replicating them, and (3) "Replicate" intraorally the recorded color shapes guided by the adjacent natural teeth using low fusing ceramic pastes (shades and stains) for color shape replication. Also, the final touch technique was followed to shape, texture and final surface finish of dental restorations. It is composed of 5 basic levels which we call dental "micro-esthetics that define shape, texture, and surface luster. CONCLUSIONS: Following the steps of both; the "Triple R" protocol and the "FINAL TOUCH" technique will help to reproduce the final shade of the restoration to create the illusion of a natural tooth to the observer. CLINICAL SIGNIFICANCE: This article shows how combining two practical methodologies to record and replicate both color shapes and surface texture of natural teeth may extend mimicking, that is, step by step natural tooth shade beyond the limitations of the available commercial shade guides.

The effect of aging on the translucency of contemporary zirconia generations: in-vitro study.

BACKGROUND: The translucency of different zirconia generations at each time point after thermocycling aging is still lacking. METHODS: Four zirconia materials were used with a total of 60 samples produced from monolithic third generation (5Y) 5 mol% yttria-stabilized zirconia polycrystalline ceramic and fourth generation zirconia (4Y) 4 mol% yttria-stabilized zirconia polycrystalline ceramic, represented by [group1:[CM-5Y] Ceramill Zolid fx (3rd generation zirconia) (Amann Girrbach, Koblach, Austria), group 2:[CM-4Y] Ceramill Zolid HT + (4th generation zirconia) (Amann Girrbach, Koblach, Austria), group 3:[CC-5Y] Cercon XT/ML (Dentsply Sirona, Germany) (3rd generation), and group 4:[CC-4Y] Cercon HT/ML (Dentsply Sirona, Germany) (4th generation)]. The L*a*b* figures were measured by using a spectrophotometer at baseline and after 10,000, 30,000, and 50,000 cycles of thermocycling. At each interval, the translucency of the samples was estimated by using the translucency formula CIEDE2000. The Scheffe post-hoc compared differences among each of the four materials. The Repeated measures ANOVA tested the differences between the materials at each of the different thermocycling intervals (p < .001). Data analyses were evaluated at a significance level of p < .05 (CI 95%). RESULTS: Two-way ANOVA revealed that at baseline the third and fourth generation's zirconia showed statistically significant differences in translucency (P < .001). Translucency values at baseline and after thermocycling exhibited statistically significant changes (p = .003). At each of the time interval; CM-4Y had the highest translucency values followed by CM-5Y, CC-4Y and CC-5Y had the least translucency values. CONCLUSIONS: The third and fourth generations of zirconia displayed different translucencies. Thermocycling affected the translucency of both third and fourth generations of zirconia. At each of the time intervals group 2:[CM-4Y] had the highest TP followed by group1:[CM-5Y], while, group 3:[CC-5Y] and group 4:[CC-4Y] had the least TP.

Evaluation of vertical marginal discrepancy and load-to-failure of monolithic zirconia and lithium disilicate laminate veneers manufactured in different thicknesses.

OBJECTIVES: This study aimed to evaluate the feasibility of monolithic zirconia laminate veneers (MZLV) compared to lithium disilicate laminate veneers (LDLV). MATERIALS AND METHODS: Sixty resin replicas, each prepared with depths of 0.5 mm, 0.7 mm, and 1 mm, were produced using a 3D printer from acrylic teeth. Laminate veneers of these thicknesses were milled from pre-sintered monolithic zirconia (3rd generation) and lithium disilicate blocks. The intaglio surface of MZLV was treated with air abrasion using 110 µm diameter silica-modified aluminium oxide particles and ceramic primer, while LDLV was etched with etchant gel and treated with the ceramic primer before cementation with resin cement. Vertical marginal discrepancy (VMD) was assessed using a stereomicroscope, and a load-to-failure test was conducted using a universal testing machine. Failure modes were evaluated macroscopically on fractured surfaces. Data were analysed statistically using Two-way ANOVA and Bonferroni correction (α = 0.05). RESULTS: LDLV samples exhibited significantly larger VMD compared to MZLV samples across all thicknesses, especially in cervical, palatal, and mean data. Within the LDLV group, load-to-fracture values for 0.7 mm and 1.0 mm thicknesses were similar, whereas for 0.5 mm thickness, it was significantly lower. In the MZLV group, load-to-fracture values were lower for 0.7 mm and 1.0 mm thicknesses compared to LDLV, but higher for 0.5 mm thickness. CONCLUSIONS: Material choice and restoration thickness significantly influence laminate veneer restorations' success. MZLV generally exhibits superior vertical marginal fit compared to LDLV, with varying load-to-failure values across different thicknesses. Clinical management of debonding in MZLV is simpler compared to restoration fracture in LDLV. CLINICAL RELEVANCE: Considering clinical factors, MZLV may be a preferable option to LDLV for this restoration with the thickness of 0.5 mm.