PEDOT:PSS-Based Prolonged Long-Term Decay Synaptic OECT with Proton-Permeable Material, Nafion.

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS), a conductive polymer, has gained popularity as the channel layer in organic electrochemical transistors (OECTs) due to its high conductivity and straightforward processing. However, difficulties arise in controlling its conductivity through gate voltage, presenting a challenge. To address this issue, aromatic amidine base, diazabicyclo[4.3.0]non-5-ene (DBN), is used to stabilize the doping state of the PEDOT chain through a reliable chemical de-doping process. Furthermore, the addition of the proton-penetrable material Nafion to the PEDOT:PSS channel layer induces phase separation between the substances. By utilizing a solution containing both PEDOT:PSS and Nafion as the channel layer of OECTs, the efficiency of ion movement into the channel from the electrolyte is enhanced, resulting in improved OECT performance. The inclusion of Nafion in the OECTs' channel layer modifies ion movement dynamics, allowing for the adjustment of synaptic properties such as pulse-paired facilitation, memory level, short-term plasticity, and long-term plasticity. This research aims to introduce new possibilities in the field of neuromorphic computing and contribute to biomimetic technology through the enhancement of electronic component performance.

Ultra-high sensitivity pH sensor based on vertical organic electrochemical transistors with extended gate.

An ultra-high sensitivity pH sensor based on vertical organic electrochemical transistors (vOECT) with extended gate was proposed. The vOECT, which exhibited high transconductance (gm), was for the first time used in the preparation of a pH sensor. The extended gate was modified by electrochemical deposition of polyaniline (PANI) using the cyclic voltammetry (CV) technique. Open circuit potential (OCP) measurements were used to optimize the scan rate, showing a super-Nernstian sensitivity at all scan rates. The pH sensor based on vOECT with extended gate was investigated at different pH levels, and it exhibited an ultra-high sensitivity of 3363.6 µA/pH in the pH range 5-9, which was about 36 times greater than the maximum current sensitivity (91 µA/pH) of other transistor-based pH sensors, to the best of our knowledge. This pH sensor performed excellently in terms of reversibility, long-term stability, and selectivity. To confirm the reliability of the pH sensor, we conducted measurements on real samples using this pH sensor and compared the results with those obtained from a standard pH meter. The ultra-high sensitivity pH sensor based on vOECT with extended gate offers a sensitive and promising alternative in environmental monitoring, food safety, chemistry, clinical diagnostics, and bio-sensing applications.

Optically Readable Organic Electrochemical Synaptic Transistors for Neuromorphic Photonic Image Processing.

Optically readable organic synaptic devices have great potential in both artificial intelligence and photonic neuromorphic computing. Herein, a novel optically readable organic electrochemical synaptic transistor (OR-OEST) strategy is first proposed. The electrochemical doping mechanism of the device was systematically investigated, and the basic biological synaptic behaviors that can be read by optical means are successfully achieved. Furthermore, the flexible OR-OESTs are capable of electrically switching the transparency of semiconductor channel materials in a nonvolatile manner, and thus the multilevel memory can be achieved through optical readout. Finally, the OR-OESTs are developed for the preprocessing of photonic images, such as contrast enhancement and denoising, and feeding the processed images into an artificial neural network, achieving a recognition rate of over 90%. Overall, this work provides a new strategy for the implementation of photonic neuromorphic systems.

A Study of the Drift Phenomena of Gate-Functionalized Biosensors and Dual-Gate-Functionalized Biosensors in Human Serum.

In this paper, we study the drift behavior of organic electrochemical transistor (OECT) biosensors in a phosphate-buffered saline (PBS) buffer solution and human serum. Theoretical and experimental methods are illustrated in this paper to understand the origin of the drift phenomenon and the mechanism of ion diffusion in the sensing layer. The drift phenomenon is explained using a first-order kinetic model of ion adsorption into the gate material and shows very good agreement with experimental data on drift in OECTs. We show that the temporal current drift can be largely mitigated using a dual-gate OECT architecture and that dual-gate-based biosensors can increase the accuracy and sensitivity of immuno-biosensors compared to a standard single-gate design. Specific binding can be detected at a relatively low limit of detection, even in human serum.

High Performance Organic Mixed Ionic-electronic Polymeric Conductor with Stability to Autoclave Sterilization.

We present a series of newly developed donor-acceptor (D-A) polymers designed specifically for organic electrochemical transistors (OECTs) synthesized by a straightforward route. All polymers exhibited accumulation mode behavior in OECT devices, and tuning of the donor comonomer resulted in a three-order-of-magnitude increase in transconductance. The best polymer gFBT-g2T, exhibited normalized peak transconductance (gm,norm) of 298±10.4 S cm-1 with a corresponding product of charge-carrier mobility and volumetric capacitance, µC*, of 847 F V-1 cm-1 s-1 and a µ of 5.76 cm2 V-1 s-1, amongst the highest reported to date. Furthermore, gFBT-g2T exhibited exceptional temperature stability, maintaining the outstanding electrochemical performance even after undergoing a standard (autoclave) high pressure steam sterilization procedure. Steam treatment was also found to promote film porosity, with the formation of circular 200 - 400 nm voids. These results demonstrate the potential of gFBT-g2T in p-type accumulation mode OECTs, and pave the way for the use in implantable bioelectronics for medical applications.

Breathable and Stretchable Organic Electrochemical Transistors with Laminated Porous Structures for Glucose Sensing.

Dynamic glucose monitoring is important to reduce the risk of metabolic diseases such as diabetes. Wearable biosensors based on organic electrochemical transistors (OECTs) have been developed due to their excellent signal amplification capabilities and biocompatibility. However, traditional wearable biosensors are fabricated on flat substrates with limited gas permeability, resulting in the inefficient evaporation of sweat, reduced wear comfort, and increased risk of inflammation. Here, we proposed breathable OECT-based glucose sensors by designing a porous structure to realize optimal breathable and stretchable properties. The gas permeability of the device and the relationship between electrical properties under different tensile strains were carefully investigated. The OECTs exhibit exceptional electrical properties (gm ~1.51 mS and Ion ~0.37 mA) and can retain up to about 44% of their initial performance even at 30% stretching. Furthermore, obvious responses to glucose have been demonstrated in a wide range of concentrations (10-7-10-4 M) even under 30% strain, where the normalized response to 10-4 M is 26% and 21% for the pristine sensor and under 30% strain, respectively. This work offers a new strategy for developing advanced breathable and wearable bioelectronics.

[Bionic optic nerve based on perovskite (CsPbBr 3) quantum-dots].

The bionic optic nerve can mimic human visual physiology and is a future treatment for visual disorders. Photosynaptic devices could respond to light stimuli and mimic normal optic nerve function. By modifying (Poly(3,4-ethylenedioxythio-phene):poly (styrenesulfonate)) active layers with all-inorganic perovskite quantum dots, with an aqueous solution as the dielectric layer in this paper, we developed a photosynaptic device based on an organic electrochemical transistor (OECT). The optical switching response time of OECT was 3.7 s. To improve the optical response of the device, a 365 nm, 300 mW·cm -2 UV light source was used. Basic synaptic behaviors such as postsynaptic currents (0.225 mA) at a light pulse duration of 4 s and double pulse facilitation at a light pulse duration of 1 s and pulse interval of 1 s were simulated. By changing the way light stimulates, for example, by adjusting the intensity of the light pulses from 180 to 540 mW·cm -2, the duration from 1 to 20 s, and the number of light pulses from 1 to 20, the postsynaptic currents were increased by 0.350 mA, 0.420 mA, and 0.466 mA, respectively. As such, we realized the effective shift from short-term synaptic plasticity (100 s recovery of initial value) to long-term synaptic plasticity (84.3% of 250 s decay maximum). This optical synapse has a high potential for simulating the human optic nerve.

Organic Electrochemical Transistor Based on Hydrophobic Polymer Tuned by Ionic Gels.

Hydrophobic conjugated polymers have poor ionic transport property, so hydrophilic side chains are often grafted for their application as organic electrochemical transistors (OECTs). However, this modification lowers their charge transport ability. Here, an ionic gel interfacial layer is applied to improve the ionic transport while retaining the charge transport ability of the polymers. By using the ionic gels comprising gel matrix and ionic liquids as the interfacial layers, the hydrophobic polymer achieves the OECT feature with high transconductance, low threshold voltage, high current on/off ratio, short switching time, and high operational stability. The working mechanism is also revealed. Moreover, the OECT performance can be tuned by varying the types and ratios of ionic gels. With the proposed ionic gel strategy, OECTs can be effectively realized with hydrophobic conjugated polymers.

The Influence of Regiochemistry on the Performance of Organic Mixed Ionic and Electronic Conductors.

Thiophenes functionalised in the 3-position are ubiquitous building blocks for the design and synthesis of organic semiconductors. Their non-centrosymmetric nature has long been used as a powerful synthetic design tool exemplified by the vastly different properties of regiorandom and regioregular poly(3-hexylthiophene) owing to the repulsive head-to-head interactions between neighbouring side chains in the regiorandom polymer. The renewed interest in highly electron-rich 3-alkoxythiophene based polymers for bioelectronic applications opens up new considerations around the regiochemistry of these systems as both the head-to-tail and head-to-head couplings adopt near-planar conformations due to attractive intramolecular S-O interactions. To understand how this increased flexibility in the molecular design can be used advantageously, we explore in detail the geometrical and electronic effects that influence the optical, electrochemical, structural, and electrical properties of a series of six polythiophene derivatives with varying regiochemistry and comonomer composition. We show how the interplay between conformational disorder, backbone coplanarity and polaron distribution affects the mixed ionic-electronic conduction. Ultimately, we use these findings to identify a new conformationally restricted polythiophene derivative for p-type accumulation-mode organic electrochemical transistor applications with performance on par with state-of-the-art mixed conductors evidenced by a µC* product of 267 F V-1 cm-1 s-1 .

High-Performance Bioelectronic Circuits Integrated on Biodegradable and Compostable Substrates with Fully Printed Mask-Less Organic Electrochemical Transistors.

Organic electrochemical transistors (OECTs) rely on volumetric ion-modulation of the electronic current to provide low-voltage operation, large signal amplification, enhanced sensing capabilities, and seamless integration with biology. The majority of current OECT technologies require multistep photolithographic microfabrication methods on glass or plastic substrates, which do not provide an ideal path toward ultralow cost ubiquitous and sustainable electronics and bioelectronics. At the same time, the development of advanced bioelectronic circuits combining bio-detection, amplification, and local processing functionalities urgently demand for OECT technology platforms with a monolithic integration of high-performance iontronic circuits and sensors. Here, fully printed mask-less OECTs fabricated on thin-film biodegradable and compostable substrates are proposed. The dispensing and capillary printing methods are used for depositing both high- and low-viscosity OECT materials. Fully printed OECT unipolar inverter circuits with a gain normalized to the supply voltage as high as 136.6 V-1 , and current-driven sensors for ion detection and real-time monitoring with a sensitivity of up to 506 mV dec-1 , are integrated on biodegradable and compostable substrates. These universal building blocks with the top-performance ever reported demonstrate the effectiveness of the proposed approach and can open opportunities for next-generation high-performance sustainable bioelectronics.

Ion-Selective Organic Electrochemical Transistors: Recent Progress and Challenges.

The charged species inside biofluids (blood, interstitial fluid, sweat, saliva, urine, etc.) can reflect the human body's physiological conditions and thus be adopted to diagnose various diseases early. Among all personalized health management applications, ion-selective organic electrochemical transistors (IS-OECTs) have shown tremendous potential in point-of-care testing of biofluids due to low cost, ease of fabrication, high signal amplification, and low detection limit. Moreover, IS-OECTs exhibit excellent flexibility and biocompatibility that enable their application in wearable bioelectronics for continuous health monitoring. In this review, the working principle of IS-OECTs and the recent studies of IS-OECTs for performance improvement are reviewed. Specifically, contemporary studies on material design and device optimization to enhance the sensitivity of IS-OECTs are discussed. In addition, the progress toward the commercialization of IS-OECTs is highlighted, and the recently proposed solutions or alternatives are summarized. The main challenges and perspectives for fully exploiting IS-OECTs toward future preventive and personal medical devices are addressed.

Realizing Ultrahigh Transconductance in Organic Electrochemical Transistor by Co-Doping PEDOT:PSS with Ionic Liquid and Dodecylbenzenesulfonate.

Organic electrochemical transistors (OECTs), especially the ones with high transconductance, are highly promising in sensitive detection of chemical and biological species. However, it is still a great challenge to design and fabricate OECTs with very high transconductance. Herein, an OECT with ultrahigh transconductance is reported by introducing ionic liquid and dodecylbenzenesulfonate (DBSA) simultaneously in poly(3,4-ethylenedioxythiophene): polystyrenesulfonate (PEDOT:PSS) as the semiconductive channel. Compared with the OECT based on pristine PEDOT:PSS, the OECT based on co-doped PEDOT:PSS demonstrates a significant enhancement of transconductance from 1.85 to 22.7 mS, because of the increase in volumetric capacitance and conductivity. The enhanced transconductance is attributed to the DBSA-facilitated phase separation between the ionic liquid and PEDOT:PSS, which helps to form conductive domains of ionic liquid in PEDOT:PSS matrix, and the partial dispersion of ionic liquid in the PEDOT:PSS phase. Furthermore, by using the interdigitated electrodes as the source and drain electrodes, an ultrahigh transconductance of 180 mS is obtained, which is superior to that of the state-of-the-art OECTs. Because of the ultrahigh transconductance, the obtained OECT demonstrates sensitive detection of hydrogen peroxide and glucose, making it promising in clinical diagnosis, health monitoring, and environmental surveillance.

Fast-Scanning Potential-Gated Organic Electrochemical Transistors for Highly Sensitive Sensing of Dopamine in Living Rat Brain.

Developing techniques for the highly sensitive assay of neurotransmitters is essential for understanding physiological and pathological processes. Here, we demonstrate a fast-scanning potential (FSP)-gated organic electrochemical transistor (OECT): for the highly sensitive sensing of dopamine (DA) in a living rat brain. The configuration combines the selectivity of fast-scan cyclic voltammetry (FSCV) with the high sensitivity of an OECT. The combined use of FSP as a gating mode and transconductance (gm ) as a sensing parameter further improve the sensing performance in terms of sensitivity, limit of detection, reproducibility, and stability. The FSP-OECT exhibits a sensitivity of 0.899 S M-1 and a low limit of detection down to 5 nM and was validated for in vivo monitoring of the basal level and electrically stimulated release of DA.

Homocysteine Solution-Induced Response in Aerosol Jet Printed OECTs by Means of Gold and Platinum Gate Electrodes.

Homocysteine (Hcy) is a non-protein, sulfur-containing amino acid, which is recognized as a possible risk factor for coronary artery and other pathologies when its levels in the blood exceed the normal range of between 5 and 12 µmol/L (hyperhomocysteinemia). At present, standard procedures in laboratory medicine, such as high-performance liquid chromatography (HPLC), are commonly employed for the quantitation of total Hcy (tHcy), i.e., the sum of the protein-bound (oxidized) and free (homocystine plus reduced Hcy) forms, in biological fluids (particularly, serum or plasma). Here, the response of Aerosol Jet-printed organic electrochemical transistors (OECTs), in the presence of either reduced (free) and oxidized Hcy-based solutions, was analyzed. Two different experimental protocols were followed to this end: the former consisting of gold (Au) electrodes' biothiol-induced thiolation, while the latter simply used bare platinum (Pt) electrodes. Electrochemical impedance spectroscopy (EIS) analysis was performed both to validate the gold thiolation protocol and to gain insights into the reduced Hcy sensing mechanism by the Au-gated OECTs, which provided a final limit of detection (LoD) of 80 nM. For the OECT response based on Platinum gate electrodes, on the other hand, a LoD of 180 nM was found in the presence of albumin-bound Hcy, with this being the most abundant oxidized Hcy-form (i.e., the protein-bound form) in physiological fluids. Despite the lack of any biochemical functionalization supporting the response selectivity, the findings discussed in this work highlight the potential role of OECT in the development of low-cost point-of-care (POC) electronic platforms that are suitable for the evaluation, in humans, of Hcy levels within the physiological range and in cases of hyperhomocysteinemia.

Polaron Delocalization in Donor-Acceptor Polymers and its Impact on Organic Electrochemical Transistor Performance.

Donor-acceptor (D-A) polymers are promising materials for organic electrochemical transistors (OECTs), as they minimize detrimental faradaic side-reactions during OECT operation, yet their steady-state OECT performance still lags far behind their all-donor counterparts. We report three D-A polymers based on the diketopyrrolopyrrole unit that afford OECT performances similar to those of all-donor polymers, hence representing a significant improvement to the previously developed D-A copolymers. In addition to improved OECT performance, DFT simulations of the polymers and their respective hole polarons also reveal a positive correlation between hole polaron delocalization and steady-state OECT performance, providing new insights into the design of OECT materials. Importantly, we demonstrate how polaron delocalization can be tuned directly at the molecular level by selection of the building blocks comprising the polymers' conjugated backbone, thus paving the way for the development of even higher performing OECT polymers.

Fused Bithiophene Imide Dimer-Based n-Type Polymers for High-Performance Organic Electrochemical Transistors.

The development of n-type organic electrochemical transistors (OECTs) lags far behind their p-type counterparts. In order to address this dilemma, we report here two new fused bithiophene imide dimer (f-BTI2)-based n-type polymers with a branched methyl end-capped glycol side chain, which exhibit good solubility, low-lying LUMO energy levels, favorable polymer chain orientation, and efficient ion transport property, thus yielding a remarkable OECT electron mobility (µe ) of up to ≈10-2  cm2 V-1 s-1 and volumetric capacitance (C*) as high as 443 F cm-3 , simultaneously. As a result, the f-BTI2TEG-FT-based OECTs deliver a record-high maximum geometry-normalized transconductance of 4.60 S cm-1 and a maximum µC* product of 15.2 F cm-1 V-1 s-1 . The µC* figure of merit is more than one order of magnitude higher than that of the state-of-the-art n-type OECTs. The emergence of f-BTI2TEG-FT brings a new paradigm for developing high-performance n-type polymers for low-power OECT applications.

n-Type Rigid Semiconducting Polymers Bearing Oligo(Ethylene Glycol) Side Chains for High-Performance Organic Electrochemical Transistors.

N-type conjugated polymers as the semiconducting component of organic electrochemical transistors (OECTs) are still undeveloped with respect to their p-type counterparts. Herein, we report two rigid n-type conjugated polymers bearing oligo(ethylene glycol) (OEG) side chains, PgNaN and PgNgN, which demonstrated an essentially torsion-free π-conjugated backbone. The planarity and electron-deficient rigid structures enable the resulting polymers to achieve high electron mobility in an OECT device of up to the 10-3  cm2 V-1 s-1 range, with a deep-lying LUMO energy level lower than -4.0 eV. Prominently, the polymers exhibited a high device performance with a maximum dimensionally normalized transconductance of 0.212 S cm-1 and the product of charge-carrier mobility µ and volumetric capacitance C* of 0.662±0.113 F cm-1 V-1 s-1 , which are among the highest in n-type conjugated polymers reported to date. Moreover, the polymers are synthesized via a metal-free aldol-condensation polymerization, which is beneficial to their application in bioelectronics.

Transparent, conformable, active multielectrode array using organic electrochemical transistors.

Mechanically flexible active multielectrode arrays (MEA) have been developed for local signal amplification and high spatial resolution. However, their opaqueness limited optical observation and light stimulation during use. Here, we show a transparent, ultraflexible, and active MEA, which consists of transparent organic electrochemical transistors (OECTs) and transparent Au grid wirings. The transparent OECT is made of Au grid electrodes and has shown comparable performance with OECTs with nontransparent electrodes/wirings. The transparent active MEA realizes the spatial mapping of electrocorticogram electrical signals from an optogenetic rat with 1-mm spacing and shows lower light artifacts than noise level. Our active MEA would open up the possibility of precise investigation of a neural network system with direct light stimulation.

Organic Electrochemical Transistors (OECTs) Toward Flexible and Wearable Bioelectronics.

Organic electronics have emerged as a fascinating area of research and technology in the past two decades and are anticipated to replace classic inorganic semiconductors in many applications. Research on organic light-emitting diodes, organic photovoltaics, and organic thin-film transistors is already in an advanced stage, and the derived devices are commercially available. A more recent case is the organic electrochemical transistors (OECTs), whose core component is a conductive polymer in contact with ions and solvent molecules of an electrolyte, thus allowing it to simultaneously regulate electron and ion transport. OECTs are very effective in ion-to-electron transduction and sensor signal amplification. The use of synthetically tunable, biocompatible, and depositable organic materials in OECTs makes them specially interesting for biological applications and printable devices. In this review, we provide an overview of the history of OECTs, their physical characterization, and their operation mechanism. We analyze OECT performance improvements obtained by geometry design and active material selection (i.e., conductive polymers and small molecules) and conclude with their broad range of applications from biological sensors to wearable devices.

Microscopic Determination of Carrier Density and Mobility in Working Organic Electrochemical Transistors.

A comprehensive understanding of electrochemical and physical phenomena originating the response of electrolyte-gated transistors is crucial for improved handling and design of these devices. However, the lack of suitable tools for direct investigation of microscale effects has hindered the possibility to bridge the gap between experiments and theoretical models. In this contribution, a scanning probe setup is used to explore the operation mechanisms of organic electrochemical transistors by probing the local electrochemical potential of the organic film composing the device channel. Moreover, an interpretative model is developed in order to highlight the meaning of electrochemical doping and to show how the experimental data can give direct access to fundamental device parameters, such as local charge carrier concentration and mobility. This approach is versatile and provides insight into the organic semiconductor/electrolyte interface and useful information for materials characterization, device scaling, and sensing optimization.