Surface Hydroxyl and Oxygen Vacancies Engineering in ZnSnAl LDH: Synergistic Promotion of Photocatalytic Oxidation of Aromatic VOCs.

Photocatalytic oxidation has gained great interest in environmental remediation, but it is still limited by its low efficiency and catalytic deactivation in the degradation of aromatic VOCs. In this study, we concurrently regulated the surface hydroxyl and oxygen vacancies by introducing Al into ZnSn layered double hydroxide (LDH). The presence of distorted Al species induced local charge redistribution, leading to the remarkable formation of oxygen vacancies. These oxygen vacancies subsequently increased the amount of surface hydroxyl and elongated its bond length. The synergistic effects of surface hydroxyl and oxygen vacancies greatly enhanced reactant adsorption-activation and facilitated charge transfer to generate •OH, •O2-, and 1O2, resulting in highly efficient oxidation and ring-opening of various aromatic VOCs. Compared with commercial TiO2, the optimized ZnSnAl-50 catalyst exhibited about 2-fold activity for the toluene and styrene degradation and 10-fold activity for the chlorobenzene degradation. Moreover, ZnSnAl-50 demonstrated exceptional stability in the photocatalytic oxidation of toluene under a wide humidity range of 0-75%. This work marvelously improves the photocatalytic efficiency, stability, and adaptability through a novel strategy of surface hydroxyl and oxygen vacancies engineering.

Atomically Strained Metal Sites for Highly Efficient and Selective Photooxidation.

Strain engineering is an attractive strategy for improving the intrinsic catalytic performance of heterogeneous catalysts. Manipulating strain on the short-range atomic scale to the local structure of the catalytic sites is still challenging. Herein, we successfully achieved atomic strain modulation on ultrathin layered vanadium oxide nanoribbons by an ingenious intercalation chemistry method. When trace sodium cations were introduced between the V2O5 layers (Na+-V2O5), the V-O bonds were stretched by the atomically strained vanadium sites, redistributing the local charges. The Na+-V2O5 demonstrated excellent photooxidation performance, which was approximately 12 and 14 times higher than that of pristine V2O5 and VO2, respectively. Complementary spectroscopy analysis and theoretical calculations confirmed that the atomically strained Na+-V2O5 had a high surficial charge density, improving the activation of oxygen molecules and contributing to the excellent photocatalytic property. This work provides a new approach for the rational design of strain-equipped catalysts for selective photooxidation reactions.

Self-Adaptive Aromatic Cation-π Driven Dimensional Polymorphism in Supramolecular Polymers for the Photocatalytic Oxidation and Separation of Aromatic/Cyclic Aliphatic Compounds.

The phenomenon of polymorphism is ubiquitous in nature, the controlled manipulation of which not only increases our ontological understanding of nature but also facilitates the conceptualization and realization of novel functional materials. However, achieving targeted polymorphism in supramolecular assemblies (SAs) remains a formidable challenge, largely because of the constraints inherent in controlling the specific binding motifs of noncovalent interactions. Herein, we propose self-adaptive aromatic cation-π binding motifs to construct polymorphic SAs in both the solid and solution states. Using distinct discrete cation-π-cation and long-range cation-π binding motifs enables control of the self-assembly directionality of a C2h-symmetric bifunctional monomer, resulting in the successful formation of both two-dimensional and three-dimensional crystalline SAs (2D-CSA and 3D-CSA). The differences in the molecular packing of 3D-CSA compared with that of 2D-CSA significantly improve the charge separation and carrier mobility, leading to enhanced photocatalytic activity for the aerobic oxidation of thioanisole to methyl phenyl sulfoxide (yield of 99 % vs 57 %). 2D-CSA, which has a vertical extended structure with favorable stronger interaction with toluene though face-to-face cation-π interactions than methylcyclohexane, shows higher toluene/methylcyclohexane separation efficiency than 3D-CSA (96.9 % for 2D-CSA vs 56.3 % for 3D-CSA).

NiS/Cd0.6 Zn0.4 S Schottky Junction Bifunctional Photocatalyst for Sunlight-Driven Highly Selective Catalytic Oxidation of Vanillyl Alcohol Towards Vanillin Coupled with Hydrogen Evolution Reaction.

Selective oxidation of biomass-based molecules to high-value chemicals in conjunction with hydrogen evolution reaction (HER) is an innovative photocatalysis strategy. The key challenge is to design bifunctional photocatalysts with suitable band structures, which can achieve highly efficient generation of high-value chemicals and hydrogen. Herein, NiS/Cd0.6 Zn0.4 S Schottky junction bifunctional catalysts are constructed for sunlight-driven catalytic vanillyl alcohol (VAL) selective oxidation towards vanillin (VN) coupling HER. At optimal conditions, the 8% NiS/Cd0.6 Zn0.4 S photocatalyst achieves high activity of VN production (3.75 mmol g-1 h-1 ) and HER (3.84 mmol g-1 h-1 ). It also exhibits remarkable VAL conversion (66.9%), VN yield (52.1%), and selectivity (77.8%). The photocatalytic oxidation of VAL proceeds a carbon-centered radical mechanism via the cleavage of αC-H bond. Experimental results and theoretical calculations show that NiS with metallic properties enhances the electron transfer capability. Importantly, a Ni-S-Cd "electron bridge" formed at the interface of NiS/Cd0.6 Zn0.4 S further improves the separation/transfer of electrone/h+ pairs and also furnishes HER active sites due to its smaller the |ΔGH* | value, thereby resulting in a remarkably HER activity. This work sheds new light on the selective catalytic oxidation VAL to VN coupling HER, with a new pathway towards achieving its efficient HER efficiency.

Enhanced Photocatalytic Activity of Hyper-Cross-Linked Polymers Toward Amines Oxidation Coupled with H2 O2 Generation through Extending Monomer's Conjugation Degree.

Visible-light-driven amines oxidation coupled with hydrogen peroxide (H2 O2 ) generation is a promising way to convert solar energy to chemical energy. Herein, a series of hyper-cross-linked polymers (HCPs) photocatalysts with different arenes monomers, including benzene (BE), diphenyl (DP), p-terphenyl (TP), or p-quaterphenyl (QP), were synthesized by simple Friedel-Crafts alkylation reaction. Owing to the maximum monomer's conjunction degree and excellent oxygen (O2 ) adsorption capacity, QP-HCPs exhibited highest photocatalytic activity for benzylamine oxidation coupled with H2 O2 generation under the irradiation of 455 nm Blue LED lamp. More than 99 % of benzylamine could be converted to N-benzylidenebenzylamine within 60 min. In addition, nearly stoichiometric H2 O2 was synchronously obtained with a high production rate of 9.3 mmol gcat -1 h-1 . Our work not only demonstrated that the photocatalytic activity of HCPs photocatalysts significantly depends on monomer's conjunction degree, but also provided a new strategy for converting solar energy to chemical energy.

Improved catalytic performance of ZnO via coupling with CoFe2O4 and carbon nanotubes: A new, photocatalysis-mediated peroxymonosulfate activation system, applied towards Cefixime degradation.

In this study, a ternary ZnO@spinel cobalt ferrite@carbon nanotube magnetic photocatalyst (ZSCF@CNT) was successfully synthesized and used to activate peroxymonosulfate (PMS) for Cefixime (CFX) antibiotic degradation under UVC irradiation. The morphology, optical, structural, and physicochemical properties of ZSCF@CNT were characterized and analyzed by XPS, XRD, FESEM-EDX, TEM, BET, VSM, UV-vis DRS and PL analysis. The results indicated that the ternary ZSCF@CNT photocatalyst exhibited superior catalytic activity on CFX elimination than that of individual components and binary composite catalysts, in which CFX with was rapidly removed under UVC irradiation and PMS. The effect of operational parameters including initial PMS, catalyst, and CFX concentrations and solution pH on the catalytic activity was investigated in detail; the optimal conditions were: pH: 7.0, catalyst: 0.3 g/L, PMS: 3.0 mM, leading to total CFX (10 mg/L) elimination in ∼20 min. Based on the radical scavenger tests, various radicals and non-radical species including sulfate, hydroxyl and superoxide radicals, singlet oxygen and electrons were involved in the ZSCF@CNT/PMS/UVC system. The high surface area, reduced agglomeration formation and excellent separation of photogenerated electron-hole pairs embodied in ZSCF@CNT photocatalyst conferred its superior catalytic activity and stability. The results from the tests in real water matrices revealed that ZSCF@CNT could be a promising photocatalyst to activate PMS for actual aqueous matrices' treatment.

Visible Light-Mediated Organoboron-Catalyzed Metal-Free Synthesis of Silanols from Silanes.

Herein, a four-coordinated organoboron compound, aminoquinoline diarylboron (AQDAB), is utilized as the photocatalyst in the oxidation of silane to silanol. This strategy effectively oxidizes Si-H bonds, affording Si-O bonds. Generally, the corresponding silanols can be obtained in moderate to good yields at room temperature under oxygen atmospheres, representing a green protocol to complement the existing preparation methods for silanols.

Reaction Steps in Heterogeneous Photocatalytic Oxidation of Toluene in Gas Phase-A Review.

A review of the current literature shows there is no clear consensus regarding the reaction mechanisms of air-borne aromatic compounds such as toluene by photocatalytic oxidation. Potential oxidation reactions over TiO2 or TiO2-based catalysts under ultraviolet and visible (UV/VIS) illumination are most commonly considered for removal of these pollutants. Along the pathways from a model pollutant, toluene, to final mineralization products (CO2 and H2O), the formation of several intermediates via specific reactions include parallel oxidation reactions and formation of less-reactive intermediates on the TiO2 surface. The latter may occupy active adsorption sites and causes drastic catalyst deactivation in some cases. Major hazardous gas-phase intermediates are benzene and formaldehyde, classified by the International Agency for Research on Cancer (IARC) as Group 1 carcinogenic compounds. Adsorbed intermediates leading to catalyst deactivation are benzaldehyde, benzoic acid, and cresols. The three most typical pathways of toluene photocatalytic oxidation are reviewed: methyl group oxidation, aromatic ring oxidation, and aromatic ring opening.

Human Health Risk Assessment of the Photocatalytic Oxidation of BTEX over TiO2/Volcanic Glass.

This study demonstrates rapid photocatalytic oxidation of a benzene, toluene, ethylbenzene, and xylene (BTEX) mixture over TiO2/volcanic glass. The assessment of the photocatalytic oxidation of BTEX was conducted under conditions simulating those found in indoor environments affected by aromatic hydrocarbon release. We show, under UV-A intensities of 15 mW/cm2 and an air flow rate of 55 m3/h, that low ppmv levels of BTEX concentrations can be reduced to below detectable levels. Solid-phase microextraction technique was employed to monitor the levels of BTEX in the test chamber throughout the photocatalytic oxidation, lasting approximately 21 h. Destruction of BTEX from the gas phase was observed in the following sequence: o-xylene, ethylbenzene, toluene, and benzene. This study identified sequential degradation of BTEX, in combination with the stringent regulatory level set for benzene, resulted in the air quality hazard indexes (Total Hazard Index and Hazard Quotient) remaining relatively high during the process of photocatalytic oxidation. In the practical application of photocatalytic purification, it is crucial to account for the slower oxidation kinetics of benzene. This is of particular importance due to not only its extremely low exposure limits, but also due to the classification of benzene as a Group 1 carcinogenic compound by the International Agency for Research on Cancer (IARC). Our study underscores the importance of taking regulatory considerations into account when using photocatalytic purification technology.

Photo-Fenton and TiO2 Photocatalytic Inactivation of Model Microorganisms under UV-A; Comparative Efficacy and Optimization.

Photocatalytic inactivation of pathogens in aqueous waste is gaining increasing attention. Several homogeneous and heterogeneous photocatalytic protocols exist using the Fenton's reagent and TiO2, respectively. A comprehensive study of homogeneous and heterogeneous photocatalysis on a range of microorganisms will significantly establish the most efficient method. Here, we report a comparative study of TiO2- and Fe+3-based photocatalytic inactivation under UV-A of diverse microorganisms, including Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria, bacterial spores (Bacillus stearothermophilus spores) and viruses (MS2). We also present data on the optimization of TiO2 photocatalysis, including optimal catalyst concentration and H2O2 supplementation. Our results indicate that both photo-Fenton and TiO2 could be successfully applied for the management of microbial loads in liquids. Efficient microorganism inactivation is achieved with homogeneous photocatalysis (7 mg/L Fe+3, 100 mg/L H2O2, UV-A) in a shorter processing time compared to heterogeneous photocatalysis (0.5 g/L TiO2, UV-A), whereas similar or shorter processing is required when heterogenous photocatalysis is performed using microorganism-specific optimized TiO2 concentrations and H2O2 supplementation (100 mg/L); higher H2O2 concentrations further enhance the heterogenous photocatalytic inactivation efficiency. Our study provides a template protocol for the design and further application for large-scale photocatalytic approaches to inactivate pathogens in liquid biomedical waste.

Experimental study of the purification performance of a MopFan-based photocatalytic air cleaning system.

Severe acute respiratory syndrome coronavirus (SARS-CoV)-2, the virus that causes the coronavirus disease (COVID)-19, is primarily transmitted through respiratory droplets which linger in enclosed spaces, often exacerbated by HVAC systems. Although research to improve HVAC handling of SARS-CoV-2 is progressing, currently installed HVAC systems cause problems because they recirculate air and use ineffective filters against virus. This paper details the process of developing a novel method of eliminating air pollutants and suspended pathogens in enclosed spaces using Photocatalytic Oxidation (PCO) technology. It has been previously employed to remove organic contaminants and compounds from air streams using the irradiation of titanium dioxide (TiO2) surfaces with ultraviolet (UV) lights causing the disintegration of organic compounds by reactions with oxygen (O) and hydroxyl radicals (OH). The outcome was two functional prototypes that demonstrate the operation of PCO-based air purification principle. These prototypes comprise a novel TiO2 coated fibre mop system, which provide very large surface area for UV irradiation. Four commercially accessible materials were used for the construction of the mop: Tampico, Brass, Coco, and Natural synthetic. Two types of UV lights were used: 365 nm (UVA) and 270 nm (UVC). A series of tests were conducted that proved the prototype's functionality and its efficiency in lowering volatile organic compounds (VOCs) and formaldehyde (HCHO). The results shown that a MopFan with rotary mop constructed with Coco fibres and utilising UVC light achieves the best VOC and HCHO purification performance. Within 2 h, this combination lowered HCHO by 50% and VOCs by 23% approximately.

Large-scale evaluation of microorganism inactivation by bipolar ionization and photocatalytic devices.

The COVID-19 pandemic has raised awareness in the spread of disease via airborne transmission. As a result, there has been increasing interest in technologies that claim to reduce concentrations of airborne pathogens in indoor environments. The efficacy of many of these emerging technologies is not fully understood, and the testing that has been done is often conducted at a small scale and not representative of applied settings. There is currently no standard test method for evaluating air treatment technologies, making it difficult to compare results across studies or technology types. Here, a consistent testing approach in an operational-scale test chamber with a mock recirculating heating, ventilation, and air conditioning (HVAC) system was used to evaluate the efficacy of bipolar ionization and photocatalytic devices against the non-enveloped bacteriophage MS2 in the air and on surfaces. Statistically significant differences between replicate sets of technology tests and control tests (without technologies active) are apparent after 1 h, ranging to a maximum of 0.88 log10 reduction for the bipolar ionization tests and 1.8 log10 reduction for the photocatalytic device tests. It should be noted that ozone concentrations were elevated above background concentrations in the test chamber during the photocatalytic device testing. No significant differences were observed between control and technology tests in terms of the amount of MS2 deposited or inactivated on surfaces during testing. A standardized, large-scale testing approach, with replicate testing and time-matched control conditions, is necessary for contextualizing laboratory efficacy results, translating them to real-world conditions, and for facilitating technology comparisons.

Parasitic Light Absorption, Rate Laws and Heterojunctions in the Photocatalytic Oxidation of Arsenic(III) Using Composite TiO2 /Fe2 O3.

Composite photocatalyst-adsorbents such as TiO2 /Fe2 O3 are promising materials for the one-step treatment of arsenite contaminated water. However, no previous study has investigated how coupling TiO2 with Fe2 O3 influences the photocatalytic oxidation of arsenic(III). Herein, we develop new hybrid experiment/modelling approaches to study light absorption, charge carrier behaviour and changes in the rate law of the TiO2 /Fe2 O3 system, using UV-Vis spectroscopy, transient absorption spectroscopy (TAS), and kinetic analysis. Whilst coupling TiO2 with Fe2 O3 improves total arsenic removal by adsorption, oxidation rates significantly decrease (up to a factor of 60), primarily due to the parasitic absorption of light by Fe2 O3 (88 % of photons at 368 nm) and secondly due to changes in the rate law from disguised zero-order kinetics to first-order kinetics. Charge transfer across this TiO2 -Fe2 O3 heterojunction is not observed. Our study demonstrates the first application of a multi-adsorbate surface complexation model (SCM) towards describing As(III) oxidation kinetics which, unlike Langmuir-Hinshelwood kinetics, includes the competitive adsorption of As(V). We further highlight the importance of parasitic light absorption and catalyst fouling when designing heterogeneous photocatalysts for As(III) remediation.

High specific surface CeO2-NPs doped loose porous C3N4for enhanced photocatalytic oxidation ability.

Porous C3N4(PCN) is favored by researchers because it has more surface active sites, higher specific surface area and stronger light absorption ability than traditional g-C3N4. In this study, cerium dioxide nanoparticles (CeO2-NPs) with mixed valence state of Ce3+and Ce4+were doped into the PCN framework by a two-step method. The results indicate that CeO2-NPs are highly dispersed in the PCN framework, which leads to a narrower band gap, a wider range of the light response and an improved the separation efficiency of photogenerated charge in PCN. Moreover, the specific surface area (145.69 m2g-1) of CeO2-NPs doped PCN is a 25.5% enhancement than that of PCN (116.13 m2g-1). In the experiment of photocatalytic selective oxidation of benzyl alcohol, CeO2-NPs doped porous C3N4exhibits excellent photocatalytic activity, especially Ce-PCN-30. The conversion rate of benzyl alcohol reaches 74.9% using Ce-PCN-30 as photocatalyst by 8 h of illumination, which is 25.7% higher than that of pure porous C3N4. Additionally, CeO2-NPs doped porous C3N4also exhibits better photocatalytic efficiency for other aromatic alcohols.

Photocatalytic oxidation degradation of inhibitory fatty acids for aged Chlorella vulgaris cultivation medium recycling.

The medium used for Chlorella vulgaris cultivation exerted obvious inhibitory effects on the growth of C. vulgaris after several culture-harvest cycles. The accumulated fatty acids secreted by C. vulgaris during their growth process were expected to be the cell inhibition components. In this work, the ultraviolet-driven photocatalytic oxidation technique was applied for the degradation of microalgae cell growth inhibition components in the aged cultivation medium, and the reaction parameters were optimized. The results indicated that the photocatalytic oxidation processes using 0.5 g/L [Formula: see text] NPs as the catalyst under the aeration condition showed as high as 74.61 ± 4.60% FA degradation efficiency after 20 min illumination, and the contents of -COOH, [Formula: see text] (α) and -COO-R functional groups in the aged C. vulgaris medium were significantly reduced. In addition, the modification of the photocatalyst further improved the ability of the degradation of FA. When the modified [Formula: see text]/AC and [Formula: see text]/Ag catalysts were applied, the FA degradation rates reached as high as 92.46 ± 0.37% and 93.91 ± 1.37%, respectively. In the recycled medium treated with [Formula: see text]/AC, the cell density in the stable phase reached 96.33 ± 1.83% of that in the fresh medium as the control. In summary, the photocatalytic oxidation with the modified [Formula: see text]/AC catalyst was proposed as the efficient strategy to realize the recycling of the aged C. vulgaris cultivation medium via the degradation of the FA as the cell growth inhibitors.

Modification of natural chitosan with Fe and Ce cations as photocatalyst beads: Degradation of dye chemicals and textile wastewater under UVA light.

The photocatalytic effect of ferrous and cerium loaded catalysts produced from chitosan beads (CB) was investigated for dye removal and textile wastewater degradation. Commercially available chitosan was initially shaped into beads form and modified with ferrous and cerium compounds. The amount of ferrous and cerium loaded on the chitosan beads were calculated as 22 mg Fe/g CB, 60 mg Ce/g CB, respectively. The chemical formation and morphology of the catalysts were characterized with SEM-EDS. Photocatalytic studies with UVA irradiation were carried out using 20 mg/L Direct Orange 46 (DO46) textile dye solution, 1 g/L catalyst and 10 mM H2O2 and the dye removal efficiencies for CB, Fe/CB and Ce/CB were obtained as 10%, 60% and 26%, respectively As a result of the characterization and photocatalytic studies, the produced Fe/CB was then used for the treatment of the textile industry wastewater and while 21% total organic carbon (TOC) removal efficiency was obtained, 30, 23 and 26% color removal efficiencies were calculated for 436, 525 and 620 nm wavelengths, respectively.

Postharvest quality of 'Cripps Pink' apple fruit influenced by ethylene antagonists during controlled atmosphere storage with photocatalytic oxidation.

BACKGROUND: The present study investigated the efficacy of 1H-cyclopropa[b]naphthalene (NC) and 1H-cyclopropabenzene (BC) with respect to antagonizing ethylene action and maintaining postharvest fruit quality in 'Cripps Pink' apple stored in a controlled atmosphere comprising 3.45 ± 0.45% oxygen and 2.40 ± 0.36% carbon dioxide with photocatalytic oxidation (PCO) at 0 ± 1 °C and 90 ± 5% relative humidity. RESULTS: The BC, NC, and 1-methylcyclopropene (1-MCP) fumigation treatments delayed the climacteric peaks onset and retarded ethylene production rates compared to control fruit. Treatments with ethylene antagonist also maintained fruit firmness (up to 1.12 times), titratable acidity (up to 1.08 times), malic acid (up to 1.23 times), ascorbic acid (up to 1.12 times) and total phenol levels (up to 1.19 times) higher compared to that in control fruit. The 1-MCP was more efficient in reducing the rates of ethylene production compared to NC and BC, but, in the case of all other fruit quality parameters investigated, the effect of NC and BC treatments were on a par with 1-MCP. CONCLUSION: The NC and BC have the potential to be used as ethylene antagonists in 'Cripps Pink' apple fruit stored in a controlled atmosphere with PCO. The efficacy of different concentrations of NC and BC in downregulating ethylene action, as well as interactive effects of PCO on the performance of ethylene antagonists, still warrants further investigation. © 2022 The Authors. Journal of The Science of Food and Agriculture published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

Self-cleaning, photocatalytic films on aluminum plates for multi-pollutant air remediation: promoting adhesion and activity by SiO2interlayers.

In recent years, nanoparticles have come under close scrutiny for their possible health and environmental issues, making them less attractive for photocatalytic applications in air or water purification. Replacing free nano-powders with active and stable films is thus a fundamental step towards developing effective photocatalytic devices. Aluminum represents a cheap and technologically-relevant substrate, but its photocatalytic applications have been hampered by adhesion issues and metal ion diffusion within the photocatalytic layer. In this work, the use of silica interlayers is investigated as a strategy to promote adhesion, efficiency and reusability of TiO2films deposited on aluminum plates. Films were prepared from stable titania sols to avoid the use of nano-powders. Aluminum substrates with different surface morphology were investigated and the role of the silica interlayer thickness was studied. Films were extensively characterized, studying their structure, morphology, optical properties, adhesion and hardness. Self-cleaning properties were studied with respect to their superhydrophilicity and ability to resist fouling via alkylsilanes. Photocatalytic degradation tests were carried out using both volatile organic compounds and NOx, also in recycle tests. The presence of the silica interlayer proved crucial to promote the film robustness and photocatalytic activity. The substrate morphology determined the optimal interlayer thickness, especially in terms of the film reusability.

Unintended Consequences of Air Cleaning Chemistry.

Amplified interest in maintaining clean indoor air associated with the airborne transmission risks of SARS-CoV-2 have led to an expansion in the market for commercially available air cleaning systems. While the optimal way to mitigate indoor air pollutants or contaminants is to control (remove) the source, air cleaners are a tool for use when absolute source control is not possible. Interventions for indoor air quality management include physical removal of pollutants through ventilation or collection on filters and sorbent materials, along with chemically reactive processes that transform pollutants or seek to deactivate biological entities. This perspective intends to highlight the perhaps unintended consequences of various air cleaning approaches via indoor air chemistry. Introduction of new chemical agents or reactive processes can initiate complex chemistry that results in the release of reactive intermediates and/or byproducts into the indoor environment. Since air cleaning systems are often continuously running to maximize their effectiveness and most people spend a vast majority of their time indoors, human exposure to both primary and secondary products from air cleaners may represent significant exposure risk. This Perspective highlights the need for further study of chemically reactive air cleaning and disinfection methods before broader adoption.

Innovative green/non-toxic Bi2S3@g-C3N4 nanosheets for dark antimicrobial activity and photocatalytic depollution: Turnover assessment.

Herein, green and non-toxic bismuth sulphide@graphitic carbon nitride (Bi2S3@g-C3N4) nanosheets (NCs) were firstly synthesized by ultrasonicated-assisted method and characterized with different tool. Bi2S3@g-C3N4 NCs antimicrobial activity tested against three types of microbes. As well the heterostructured Bi2S3@g-C3N4 NCs was investigated for removing dye and hexavalent chromium under visible light and showed high efficiency of photocatalytic oxidation/reduction higher than g-C3N4 alone, attributing to lower recombination photogenerated electron-hole pairs. Bi2S3@g-C3N4 NCs showed high antimicrobial efficiencies against Staphylococcus aureus (S. aureus) as a Gram positive bacterium, Escherichia coli (E. Coli)as a Gram negative bacterium and Candida albicans (C. albicans) and that the disinfection rates are 99.97%, 99.98% and 99.92%, respectively. The core mechanism is that the bacterial membrane could be destroyed by reactive oxygen species. The Bi2S3@g-C3N4 NCs is promising for environmental disinfection including water and public facilities disinfection and solar photocatalytic depollution. Turnover number (TON) and Turnover frequency (TOF) are used as concise assessment indicator for photocatalytic efficiency.