Food contamination from packaging material with special focus on the Bisphenol-A.

Additives, such as bisphenol A (BPA) that are added to packaging material to enhance functionality may migrate into food products creating a concern for food safety. BPA has been linked to various chronic diseases, such as: diabetes, obesity, prostate cancer, impaired thyroid function, and several other metabolic disorders. To safeguard consumers, BPA migration limits have been defined by regulatory bodies. However, it is important to address the underlying factors and mechanisms so that they can be optimized in order to minimize BPA migration. In this review, we determine the relative importance of the factors, i.e. temperature, contact time, pH, food composition, storage time and temperature, package type, cleaning, and aging, and packaging damage that promote BPA migration in foods. Packaging material seems to be the key source of BPA and the temperature (applied during food production, storage, can sterilization and cleaning processes) was the critical driver influencing BPA migration.

Perioperative Outcomes: Polycarbonate Polyurethane Artificial Blood Vessel Versus Polyester Artificial Blood Vessel.

OBJECTIVE: The objective of this study was to compare the perioperative performance of the novel large-diameter composite polycarbonate polyurethane graft and the polyester graft. METHODS: In this study, we retrospectively analyzed 14 patients with thoracic aortic prosthesis replacement from 2016 to 2021. The preoperative, intraoperative, and postoperative data of the 2 groups were assessed in detail. RESULTS: We defined the patients with polyester grafts as the control group and the patients with polycarbonate polyurethane grafts as the experimental group. The total operation time of the experimental group was significantly shorter than that of the control group, which were 159.29±38.13 minutes and 252.57±64.40 minutes, respectively (p<0.001). The length of time from aortic opening to the end of operation in the experimental group was significantly shorter than that in the control group, which were 70.43±8.08 minutes and 124.71±37.59 minutes, respectively (p<0.001). The mean total drainage of pleural fluid was lower in the experimental group than in the control group (383.43±139.68 mL vs. 828.00±457.27 mL; p<0.05). The mean postoperative in-hospital time was shorter in the experimental group than in the control group (6.71±0.75 days vs. 9.43±2.82 days; p<0.05). CONCLUSIONS: This study provides preliminary evidence that the novel artificial blood vessel has good mechanical properties, histocompatibility, hemocompatibility, and anti-seepage function in the human body. A multicenter randomized controlled trial is needed for further validation. CLINICAL IMPACT: The novel hybrid polycarbonate polyurethane (PCU)/polyester three-layered large-diameter artificial blood vessel simulates the internal, middle, and external layers of the human blood vessels. The inner and outer layer are made of PCU, and the middle reinforcing layer is woven by polyester. Because of the three-layered structure, this artificial blood vessel has excellent anti-seepage and anti-infection functions. the inner and outer layers of the blood vessel made of PCU let this artificial blood vessel has excellent blood compatibility, outstanding biocompatibility, high endothelialization rate, and 100% patency. By comparing the perioperative outcomes with the polyester artificial blood vessel, we find it has good mechanical properties, histocompatibility, hemocompatibility and anti-seepage function in the human body.

Bisphenol A release from CAD/CAM splint materials.

This study aimed to investigate the bisphenol A (BPA) release from four CAD/CAM splint materials: three polycarbonate-based (DD BioSplint C, Splint Plus Biostar, Temp Premium Flexible) and one polymethylmethacrylate-based (Temp Basic) material. From each material, ten cylindrical samples (n = 40) were immersed in high-performance liquid chromatography (HPLC) grade water following ISO 10993-12 and incubated for 24 h in an incubation shaker at 37°C and 112 rpm. Following BPA derivatization, analysis was performed by high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS). After 24 h of incubation, all investigated materials released significant amounts of BPA compared to water blanks. The material-dependent elution increased in the following order: DD BioSplint C < Splint Plus Biostar < Temp Basic < Temp Premium Flexible. Subtracting extraneous BPA, the concentrations ranged between 2.27 ng/mL and 12.65 ng/mL. After extrapolating the concentrations in relation to the average surface area of occlusal splints, the amount of BPA per mL exceeded the Tolerable Daily Intake (TDI) set by the European Union for a person weighing 70 kg by 1.32-6.16 times. Contrary to the release from previously investigated materials, BPA elution from CAD/CAM splint materials was highly elevated. Considering the increasing adaptation of CAD/CAM techniques, elution from them may represent a relevant BPA source in daily dental practice.

Exposure to emissions generated by 3-dimensional printing with polycarbonate: effects on peripheral vascular function, cardiac vascular morphology and expression of markers of oxidative stress in male rat cardiac tissue.

Three-dimensional (3D) printing with polycarbonate (PC) plastic occurs in manufacturing settings, homes, and schools. Emissions generated during printing with PC stock and bisphenol-A (BPA), an endocrine disrupter in PC, may induce adverse health effects. Inhalation of 3D printer emissions, and changes in endocrine function may lead to cardiovascular dysfunction. The goal of this study was to determine whether there were any changes in markers of peripheral or cardiovascular dysfunction in animals exposed to PC-emissions. Male Sprague Dawley rats were exposed to PC-emissions generated by 3D printing for 1, 4, 8, 15 or 30 d. Exposure induced a reduction in the expression of the antioxidant catalase (Cat) and endothelial nitric oxide synthase (eNos). Endothelin and hypoxia-induced factor 1α transcripts increased after 30 d. Alterations in transcription were associated with elevations in immunostaining for estrogen and androgen receptors, nitrotyrosine, and vascular endothelial growth factor in cardiac arteries of PC-emission exposed animals. There was also a reduction eNOS immunostaining in cardiac arteries from rats exposed to PC-emissions. Histological analyses of heart sections revealed that exposure to PC-emissions resulted in vasoconstriction of cardiac arteries and thickening of the vascular smooth muscle wall, suggesting there was a prolonged vasoconstriction. These findings are consistent with studies showing that inhalation 3D-printer emissions affect cardiovascular function. Although BPA levels in animals were relatively low, exposure-induced changes in immunostaining for estrogen and androgen receptors in cardiac arteries suggest that changes in the action of steroid hormones may have contributed to the alterations in morphology and markers of cardiac function.

Biofilm formation of the food spoiler Brochothrix thermosphacta on different industrial surface materials using a biofilm reactor.

Brochothrix thermosphacta is considered as a major food spoiler bacteria. This study evaluates biofilm formation by B. thermosphacta CD337(2) - a strong biofilm producer strain - on three food industry materials (polycarbonate (PC), polystyrene (PS), and stainless steel (SS)). Biofilms were continuously grown under flow at 25 °C in BHI broth in a modified CDC biofilm reactor. Bacterial cells were enumerated by plate counting, and biofilm spatial organization was deciphered by combining confocal laser scanning microscopy and image analysis. The biofilms had the same growth kinetics on all three materials and reach 8log CFU/cm2 as maximal concentration. Highly structured biofilms were observed on PC and PS, but less structured ones on SS. This difference was confirmed by structural quantification analysis using the image analysis software tool BiofilmQ. Biofilm on SS show less roughness, density, thickness and volume. The biofilm 3D structure seemed to be related to the coupon topography and roughness. The materials used in this study do not affect biofilm growth. However, their roughness and topography affect the biofilm architecture, which could influence biofilm behaviour.

Silver nanopopcorns decorated on flexible membrane for SERS detection of nitrofurazone.

The synthesis of three-dimensional silver nanopopcorns (Ag NPCs) onto a flexible polycarbonate membrane (PCM) for the detection of nitrofurazone (NFZ) on the fish surface by surface-enhanced Raman spectroscopy (SERS) is presented. The proposed flexible Ag-NPCs/PCM SERS substrate exhibits significant Raman signal intensity enhancement with the measured enhancement factor of 2.36 × 106. This is primarily attributed to the hotspots created on Ag NPCs, including numerous nanoscale protrusions and internal crevices distributed across the surface of Ag NPCs. The detection of NFZ by this flexible SERS substrate demonstrates a low limit of detection (LOD) of 3.7 × 10-9 M and uniform and reproducible Raman signal intensities with a relative standard deviation below 8.34%. It also exhibits excellent stability, retaining 70% of its efficacy even after 10 days of storage. Notably, the practical detection of NFZ in tap water, honey water, and fish surfaces achieves LOD values of 1.35 × 10-8 M, 5.76 × 10-7 M, and 3.61 × 10-8 M, respectively,  which highlights its effectiveness across different sample types. The developed Ag-NPCs/PCM SERS substrate presents promising potential for sensitive SERS detection of toxic substances in real-world samples.

A 1 × 8 Optical Splitter Based on Polycarbonate Multicore Polymer Optical Fibers.

Visible light communication (VLC) is becoming more relevant due to the accelerated advancement of optical fibers. Polymer optical fiber (POF) technology appears to be a solution to the growing demand for improved transmission efficiency and high-speed data rates in the visible light range. However, the VLC system requires efficient splitters with low power losses to expand the optical energy capability and boost system performance. To solve this issue, we propose an effective 1 × 8 optical splitter based on multicore polycarbonate (PC) POF technology suitable for functioning in the green-light spectrum at a 530 nm wavelength. The new design is based on replacing 23 air-hole layers with PC layers over the fiber length, while each PC layer length is suitable for the light coupling of the operating wavelength, which allows us to set the right size of each PC layer between the closer PC cores. To achieve the best result, the key geometrical parameters were optimized through RSoft Photonics CAD suite software that utilized the beam propagation method (BPM) and analysis using MATLAB script codes for finding the tolerance ranges that can support device fabrication. The results show that after a light propagation of 2 mm, an equally green light at a 530 nm wavelength is divided into eight channels with very low power losses of 0.18 dB. Additionally, the splitter demonstrates a large bandwidth of 25 nm and stability with a tolerance range of ±8 nm around the operated wavelength, ensuring robust performance even under laser drift conditions. Furthermore, the splitter can function with 80% and above of the input signal power around the operated wavelength, indicating high efficiency. Therefore, the proposed device has a great potential to boost sensing detection applications, such as Raman spectroscopic and bioengineering applications, using the green light.

Modulus-Modulated All-Organic Core-Shell Nanofiber with Remarkable Piezoelectricity for Energy Harvesting and Condition Monitoring.

The low piezoelectricity of piezoelectric polymers significantly restricts their applications. Introducing inorganic fillers can slightly improve the piezoelectricity of polymers, whereas it is usually at the cost of flexibility and durability. In this work, using a modulus-modulated core-shell structure strategy, all-organic nanofibers with remarkable piezoelectricity were designed and prepared by a coaxial electrospinning method. It was surprisingly found that the introduction of a nonpiezoelectric polymeric core (e.g., polycarbonate, PC) can result in 110% piezoelectric coefficient (d33) enhancement in a poly(vinylidenefluoride-co-trifluoroethylene) (PVDF-TrFE) nanofiber. Accordingly, the all-organic PVDF-TrFE@PC core-shell nanofiber exhibits record-high energy-harvesting performance (i.e., 126 V output voltage, 710 mW m-2 power density) among the reported organic piezoelectric materials. In addition, the excellent sensing capability of the core-shell nanofiber enabled us to develop a wireless vibration monitoring and analyzing system, which realizes the real-time vibration detection of a power transformer.

Self-Healable, Transparent, Biodegradable, and Shape Memorable Polyurethanes Derived from Carbon Dioxide-Based Diols.

A series of CO2-based thermoplastic polyurethanes (TPUs) were prepared using CO2-based poly(polycarbonate) diol (PPCDL), 4,4'-methylenebis (cyclohexyl isocyanate) (HMDI), and polypropylene glycol (PPG and 1,4-butanediol (BDO) as the raw materials. The mechanical, thermal, optical, and barrier properties shape memory behaviors, while biocompatibility and degradation behaviors of the CO2-based TPUs are also systematically investigated. All the synthesized TPUs are highly transparent amorphous polymers, with one glass transition temperature at ~15-45 °C varying with hard segment content and soft segment composition. When PPG is incorporated into the soft segments, the resultant TPUs exhibit excellent self-healing and shape memory performances with the average shape fixity ratio and shape recovery ratio as high as 98.9% and 88.3%, respectively. Furthermore, the CO2-based TPUs also show superior water vapor permeability resistance, good biocompatibility, and good biodegradation properties, demonstrating their pretty competitive potential in the polyurethane industry applications.

Penetration performance of protective materials from crossbow attack: a preliminary study.

Crossbow-related injuries resulting in serious and mortal consequences have increased in recent years, and although significant research exists for both injury and fatality on the human body, limited data exists on the lethality of the bolt and the failure modes of protective materials. This paper concerns itself with the experimental validation of four differing crossbow bolt geometries, their effects on material failure and potentially lethality. During this study, four different types of crossbow bolt geometries were tested against two protection mechanisms that differed in mechanical properties, geometry, mass and size. The results show that at 67 ms-1, ogive, field and combo tips do not provide lethal effect at 10-m range, whilst a broadhead tip will perforate both the para-aramid and a reinforced area of polycarbonate material consisting of two 3-mm plates at 63-66 ms-1. Although perforation was apparent with a more honed tip geometry, the chain mail layering within the para-aramid protection and friction caused by polycarbonate petalling on the arrow body reduced the velocity enough to demonstrate the materials under test are effective at withstanding crossbow attack. Subsequent calculation of the maximum velocity that arrows could achieve if fired from the crossbow within this study shows results close to the overmatch value of each material and therefore a requirement to advance the knowledge in this field to influence the development of more effective armour protection mechanisms.

Aqueous Developable and CO2-Sourced Chemical Amplification Photoresist with High Performance.

Seeking high-performance photoresists is an important item for semiconductor industry due to the continuous miniaturization and intelligentization of integrated circuits. Polymer resin containing carbonate group has many desirable properties, such as high transmittance, acid sensitivity and chemical formulation, thus serving as promising photoresist material. In this work, a series of aqueous developable CO2-sourced polycarbonates (CO2-PCs) were produced via alternating copolymerization of CO2 and epoxides bearing acid-cleavable cyclic acetal groups in the presence of tetranuclear organoborane catalyst. The produced CO2-PCs were investigated as chemical amplification resists in deep ultraviolet (DUV) lithography. Under the catalysis of photogenerated acid, the acetal (ketal) groups in CO2-PC were hydrolysed into two equivalents of hydroxyl groups, which change the exposed area from hydrophobicity to hydrophilicity, thus enabling the exposed area to be developed with water. Through normalized remaining thickness analysis, the optimal CO2-derived resist achieved a remarkable sensitivity of 1.9 mJ/cm2, a contrast of 7.9, a favorable resolution (750 nm, half pitch), and a good etch resistance (38 % higher than poly(tert-butyl acrylate)). Such performances outperform commercial KrF and ArF chemical amplification resists (i.e., polyhydroxystyrene-derived and polymethacrylate-based resists), which endows broad application prospects in the field of DUV (KrF and ArF) and extreme ultraviolet (EUV) lithography for nanomanufacturing.

Closed-Loop Recycling of Mixed Plastics of Polyester and CO2-Based Polycarbonate to a Single Monomer.

Physical blending is an effective strategy for tailoring polymeric materials to specific application requirements. However, physically blended mixed plastics waste adds additional barriers in mechanical or chemical recycling. This difficulty arises from the intricate requirement for meticulous sorting and separation of the various polymers in the inherent incompatibility of mixed polymers during recycling. To overcome this impediment, this work furthers the emerging single-monomer - multiple-materials approach through the design of a bifunctional monomer that can not only orthogonally polymerize into two different types of polymers - specifically lactone-based polyester and CO2-based polycarbonate - but the resultant polymers and their mixture can also be depolymerized back to the single, original monomer when facilitated by catalysis. Specifically, the lactone/epoxide hybrid bifunctional monomer (BiLO) undergoes ring-opening polymerization through the lactone manifold to produce polyester, PE(BiLO), and is also applied to ring-opening copolymerization with CO2, via the epoxide manifold, to yield polycarbonate, PC(BiLO). Remarkably, a one-pot recycling process of a BiLO-derived PE/PC blend back to the constituent monomer BiLO in >99 % selectivity was achieved with a superbase catalyst at 150 °C, thereby effectively obviating the requirement for sorting and separation typically required for recycling of mixed polymers.

Nano porous polycarbonate membranes stimulating cell adhesion and promoting osteogenic differentiation and differential mRNA expression.

Tissue engineering is thought to be the ideal therapy for bone defect reconstructive treatment. In this study, we present a method of utilizing micro/nano porous polycarbonate membranes (PCMs) as the extracellular matrix to cultivate the human periodontal ligament cells (hPDLCs) and investigate the osteogenic differentiation of those cells. We also compared the osteogenic enhancing abilities of different pore size PCMs. The pore diameters of the candidate membranes are 200 nm, 800 nm, 1200 nm, and 10 µm respectively, and their physical properties are identified. After seeding and cultivating on the PCMs, hPDLCs can be stimulated to undergo osteogenic differentiation, in which the 200 nm PCM is proved to have the most optimal osteo-induction ability. The results of in vivo experiments provide strong evidence suggesting that the hPDLCs stimulated by 200 nm PCM greatly accelerates the healing of bone reconstruction in mice skull defects, as well as promote the process of ectopic osteogenesis. RNA-sequencing was conducted to determine the differential mRNA expression profile during the osteogenesis process of hPDLCs on PCMs. GO and KEGG enrichment analysis were conducted to study the regulatory mechanisms, in which osteogenic marker expression such as Hippo, TGF-ß, and PI3K-Akt signaling pathways were significantly up-regulated. The up-regulation indicates the promising potential of nano porous PCMs for promoting osteogenesis for bone regeneration applications. Ultimately, signaling pathways that promote osteogenesis warrants further exploration.

Peptide-Decorated Degradable Polycarbonate Nanogels for Eliciting Antigen-Specific Immune Responses.

For successful therapeutic interventions in cancer immunotherapy, strong antigen-specific immune responses are required. To this end, immunostimulating cues must be combined with antigens to simultaneously arrive at antigen-presenting cells and initiate cellular immune responses. Recently, imidazoquinolines have shown their vast potential as small molecular Toll-like receptor 7/8 (TLR7/8) agonists for immunostimulation when delivered by nanocarriers. At the same time, peptide antigens are promising antigen candidates but require combination with immune-stimulating adjuvants to boost their immunogenicity and exploit their full potential. Consequently, we herein present biodegradable polycarbonate nanogels as versatile delivery system for adjuvants within the particles' core as well as for peptide antigens by surface decoration. For that purpose, orthogonally addressable multifunctional polycarbonate block copolymers were synthesized, enabling adjuvant conjugation through reactive ester chemistry and peptide decoration by strain-promoted alkyne-azide cycloaddition (SPAAC). In preparation for SPAAC, CD4+-specific peptide sequences of the model protein antigen ovalbumin were equipped with DBCO-moieties by site-selective modification at their N-terminal cysteine. With their azide groups exposed on their surface, the adjuvant-loaded nanogels were then efficiently decorated with DBCO-functional CD4+-peptides by SPAAC. In vitro evaluation of the adjuvant-loaded peptide-decorated gels then confirmed their strong immunostimulating properties as well as their high biocompatibility. Despite their covalent conjugation, the CD4+-peptide-decorated nanogels led to maturation of primary antigen-presenting cells and the downstream priming of CD4+-T cells. Subsequently, the peptide-decorated nanogels loaded with TLR7/8 agonist were successfully processed by antigen-presenting cells, enabling potent immune responses for future application in antigen-specific cancer immunotherapy.

Electron Beam Processing as a Promising Tool to Decontaminate Polymers Containing Brominated Flame Retardants.

Electron Beam (EB) irradiation was utilized to decontaminate model systems of industrial polymers that contain a brominated flame retardant (BFR). Acrylonitrile-butadiene-styrene (ABS) and Polycarbonate (PC) are two types of polymers commonly found in Waste Electrical and Electronic Equipment (WEEE). In this study, these polymers were exposed to EB irradiation to degrade DecaBromoDiphenylEther (DBDE), one of the most toxic BFRs. Fourier-transform infrared spectroscopy analysis demonstrated an 87% degradation rate of DBDE for the ABS-DBDE system and 91% for the PC-DBDE system following an 1800 kGy irradiation dose. Thermal analysis using Differential Scanning Calorimetry revealed the presence of crosslinking in ABS and a minor reduction in the glass transition temperature of PC after EB processing. Polymers exhibited thermal stability after photolysis, as indicated by thermogravimetric analysis. In summary, EB irradiation had no impact on the overall thermal properties of both polymers. High-resolution mass spectrometry analysis has confirmed the debromination of both ABS-DBDE and PC-DBDE systems. Therefore, the results obtained are promising and could offer an alternative approach for removing bromine and other additives from plastic E-waste.

Recycling of Plastics from E-Waste via Photodegradation in a Low-Pressure Reactor: The Case of Decabromodiphenyl Ether Dispersed in Poly(acrylonitrile-butadiene-styrene) and Poly(carbonate).

Recycling of plastic waste from electrical and electronic equipment (EEE), containing brominated flame retardants (BFR) remains difficult due to the increasingly stringent regulations on their handling and recovery. This report deals with photodegradation in a low-pressure reactor applying UV-visible light on Decabromodiphenyl ether (DBDE or BDE-209) randomly dispersed in commercially available Poly(acrylonitrile-butadiene-styrene) (ABS) and Poly(carbonate) (PC). The aim of this study is to investigate the possibility of decomposing a BFR in plastic waste from EEE while maintaining the specifications of the polymeric materials in order to allow for their recycling. The photodegradation of the extracted BFR was monitored using infrared spectroscopy and gas chromatography coupled with mass spectroscopy. DBDE underwent rapid photodegradation during the first minutes of exposure to UV-visible light and reached degradation yields superior to 90% after 15 min of irradiation. The evaluation of polymer properties (ABS and PC) after irradiation revealed superficial crosslinking effects, which were slightly accelerated in the presence of DBDE. However, the use of a low-pressure reactor avoids large photooxidation and allowed to maintain the thermal and structural properties of the virgin polymers.

[Inter-laboratory Study on the Modified Methods for Analyzing Bisphenol A Content for Migration Tests from Polycarbonate Food Apparatuses, Containers, and Packaging].

An inter-laboratory study involving 24 laboratories was conducted to validate the modified analytical method for the migration solution of heptane for the determination of bisphenol A migrating from polycarbonate food processing materials. In this study, two concentrations of samples were blindly coded. Each laboratory determined the analyte (bisphenol A, phenol and p-tert-butylphenol) concentration in each sample according to the established protocol. The obtained values were analyzed statistically using internationally accepted guidelines. Horwitz ratios were calculated based on the reproducibility relative standard deviation (RSDR), which was estimated from the inter-laboratory study, and predicted RSDR, which was calculated using the Horwitz/Thompson equation. Horwitz ratios of the two samples ranged from 0.15 to 0.37 for the three compounds, meeting the performance criteria of less than 2 set by the Codex Alimentarius for analytical method approval. These results showed that this modified analytical method shows good performance as an analytical method for the migration solution of heptane.

[Modified Methods for Analyzing Bisphenol A Content for Migration Tests from Polycarbonate Food Apparatuses, Containers, and Packaging].

A validation study was performed on the modified analytical method for the migration solution of heptane, 20% ethanol and 4% acetic acid for the determination of bisphenol A migrating from polycarbonate food apparatuses, containers, and packaging. The analytes for the method were bisphenol A, phenol and p-tert-butylphenol. The repeatability, within-laboratory reproducibility and trueness of the method was estimated in the range of 0.2-1.8%, 0.4-2.6% and 95-102% respectively. These results showed that the method is useful as an analytical method for the migration solution of heptane, 20% ethanol and 4% acetic acid. Furthermore, the applicability of the determination methods with a fluorescence detector was verified. As a result of the validation study, the repeatability, within-laboratory reproducibility and trueness of the method was estimated in the range of 0.1-2.9%, 0.2-3.1% and 94-101% respectively. It was confirmed that the measurement with a fluorescence detector is also available.

Development of DNA Bio-chip for Detection of Mutations of rpoB, embB and inhA Genes in Drug-Resistant Mycobacterium Tuberculosis.

Drug-resistant (DR) tuberculosis (TB) is a global threat to health security and TB control programs. Since conventional drug susceptibility testing (DST) takes several weeks, we have developed a molecular method for the rapid identification of DR strains of Mycobacterium Tuberculosis (M.tb) utilizing DNA bio-chips. DNA bio-chips were prepared by immobilizing oligonucleotides (probes) on highly microporous polycarbonate track-etched membranes (PC-TEM) as novel support. Bio-chip was designed to contain 15 specific probes to detect mutations in three genes (rpoB, embB, and inhA). A sensitive and specific chemiluminescence based bio-chip assay was developed based on multiplex PCR followed by hybridization on bio-chip. Fifty culture isolates were used to evaluate the ability of in-house developed bio-chip to detect the mutations. Bio-chip analysis shows that 37.7% of samples show wild type sequences, 53.3% of samples were monoresistance showing resistance to either rifampicin (RMP), isoniazid (INH), or ethambutol (EMB). 4.4% of samples were polydrug resistant showing mutations in both the rpoB gene and embB gene while 4.4% of samples were multidrug-resistant (MDR), harboring mutations in the rpoB and inhA genes. The results were compared with DST and sequencing. Compared to sequencing, bio-chip assay shows a sensitivity of 96.5% and specificity of 100% for RMP resistance. For EMB and INH, the results were in complete agreement with sequencing. This study demonstrates the first-time use of PC-TEMs for developing DNA bio-chip for the detection of mutations associated with drug resistance in M.tb. Developed DNA bio-chip accurately detected different mutations present in culture isolates and thus provides detailed and reliable data for clinical diagnosis.

Bionate® nucleus disc replacement: bench testing comparing two different designs.

BACKGROUND: Intervertebral disc nucleus degeneration initiates a degenerative cascade and can induce chronic low back pain. Nucleus replacement aims to replace the nucleus while the annulus is still intact. Over time, several designs have been introduced, but the definitive solution continues to be elusive. Therefore, we aimed to create a new nucleus replacement that replicates intact intervertebral disc biomechanics, and thus has the potential for clinical applications. MATERIALS AND METHODS: Two implants with an outer ring and one (D2) with an additional midline strut were compared. Static and fatigue tests were performed with an INSTRON 8874 following the American Society for Testing and Materials F2267-04, F2346-05, 2077-03, D2990-01, and WK4863. Implant stiffness was analyzed at 0-300 N, 500-2000 N, and 2000-6000 N and implant compression at 300 N, 1000 N, 2000 N, and 6000 N. Wear tests were performed following ISO 18192-1:2008 and 18192-2:2010. GNU Octave software was used to calculate movement angles and parameters. The statistical analysis package R was used with the Deducer user interface. Statistically significant differences between the two designs were analyzed with ANOVA, followed by a post hoc analysis. RESULTS: D1 had better behavior in unconfined compression tests, while D2 showed a "jump." D2 deformed 1 mm more than D1. Sterilized implants were more rigid and deformed less. Both designs showed similar behavior under confined compression and when adding shear. A silicone annulus minimized differences between the designs. Wear under compression fatigue was negligible for D1 but permanent for D2. D1 suffered permanent height deformation but kept its width. D2 suffered less height loss than D1 but underwent a permanent width deformation. Both designs showed excellent responses to compression fatigue with no breaks, cracks, or delamination. At 10 million cycles, D2 showed 3-times higher wear than D1. D1 had better and more homogeneous behavior, and its wear was relatively low. It showed good mechanical endurance under dynamic loading conditions, with excellent response to axial compression fatigue loading without functional failure after long-term testing. CONCLUSION: D1 performed better than D2. Further studies in cadaveric specimens, and eventually in a clinical setting, are recommended. Level of evidence 2c.