Poly(ether-sulfone)/MWCNT nanocomposites manufactured by powder metallurgy route and their dynamic mechanical properties.

Dynamic mechanical properties of the poly(ether-sulfone) (PES)/multi-walled carbon nanotube (MWCNT) nanocomposites manufactured by powder metallurgical route was discussed for the first time. The structural investigation of the nanocomposites was analysed by x-ray diffraction. At room temperature, both storage modulus and microhardness of the nanocomposites increased by more than 60% while the strengthening efficiency at higher temperatures is several-folds compared to that of neat PES. The nanocomposites exhibited better damping behaviour compared to neat PES. The Cole-Cole plot indicated a good interaction between the PES and the MWCNT. Moreover, the coefficient of reinforcement decreased by 42% while the degree of entanglement increased.

ß-cyclodextrin modified GO ultrafiltration membranes with enhanced antifouling property for water purification.

The study investigated the influence of additives on the fabrication of mixed matrix membranes comprising polyethersulfone (PES), with a specific focus on hydrophilicity, flux, morphology, and antifouling properties. Carboxymethyl modified ß-cyclodextrin (CMß-CD) was used to enhance the dispersion and hydrophilicity of graphene oxide (GO), leading to the formation of a hydrophilic and stable composite nanoparticle (CMCD@GO). The hydrophilicity (WCA <51.5°) and water flux (32.6 L m-2.h-1) of the modified PES membranes (MCDGO-x) were improved by the incorporation of CMCD@GO nanoparticles, while that of PES membrane was 79.7° and 10.6 L m-2.h-1. The rate of backscattered light intensity (ΔBS) of MCDGO-x suspensions remains stable, suggesting stable dispersion of CMCD@GO in organic solvents. Compared to the bare PES membrane, the MCDGO-x membrane exhibits a thinner active layer and a finger-like structure. The MCDGO-x membrane exhibited excellent naphthenic acids (NAs) rejection (>93.2%) due to reduced roughness and higher hydrophilicity, while the GO-modified PES membrane (MGO-5) exhibited lower NAs rejection (87.2%). Furthermore, the MCDGO-5 membrane showed higher flux recovery ratio (FRR) of 79.3% compared to MGO-5 membrane (68.5%) after three cycles, indicating the antifouling performance of MCDGO-x for NAs was significantly improved. The combination of CMß-CD and GO enhance the flux and antifouling properties of PES ultrafiltration membranes, suggesting significant potential for applications in the purification of oil sands process water and the treatment of oily wastewater.

Construction of self-repairing polyethersulfone membrane with high density hydrophilic microregions by two dimensional restricted channels for enhanced dyes/salts selective separation.

Based on the dye/salts separation efficiency and membrane injury caused by serious pollution of dye/salts wastewater, this study constructed a 2D tight ultrafiltration membrane that could both solve the membrane injury problem and improve the dye/salts separation efficiency, the compatibility of good self-healing performance and penetration performance by 2D material magnesium-aluminum Layered double hydroxide (MgAl-LDH). The self-repairing of physical injury was achieved through the swelling effect of AMPS-PAN, this property was proved by permeate flux, the retention performance of salts in dye/salts solution, the comparison of scanning electron microscope (SEM), and the mechanical strength after physical injury. The healing of chemical injury occured through the reaction of CC and polyethersulfone chain breakage, which was confirmed by X-ray photoelectron spectroscopy (XPS), permeate flux, the retention performance of salts in dye/salts solution, and mechanical property. The high separation efficiency of dye/salts was achieved through 2D material MgAl-LDH, which was proved by separation selectivity ɑ. The compatibility of good self-healing performance and penetration performance was obtained by 2D material MgAl-LDH, which was proved by the penetration and self-healing performance. Morever, the membrane illustrated excellent both permeability and dye/sals separation efficiency, just like the permeate flux, the retention performance of sodium sulfate in methyl blue/sodium sulfate solution, the retention performance of Na2SO4 in methyl blue/Na2SO4 solution, the retention rate of methyl blue were 99.1 L/m2h, 12.5%, 7.9%, 97.7%, respectively. The results of pollution index and contact angle also proved that the membrane had anti-pollution performance.

Safety and performance of the Clearum™ high flux hemodialyzer.

BACKGROUND: Clearum™ is a high flux steam sterilized dialyzer for patients with hemodialysis or hemodiafiltration. This study evaluated the safety and performance of the Clearum high flux steam sterilized hemodialyzer in the removal of small and middle-sized toxins. METHODS: A prospective, interventional, nonrandomized study enrolled twenty end-stage renal disease patients undergoing hemodialysis. The Clearum high flux steam sterilized dialyzer was compared to Fresenius FX dialyzers for baseline comparison. The duration of the trial was 2 weeks for the FX dialyzer and 6 weeks with the Clearum high flux steam sterilized dialyzer. In vitro studies with dextrans of varying sizes were performed to compare the membrane characteristics and sieving coefficient curves for the two dialyzers. RESULTS: The primary objective of a mean urea reduction ratio >65% was met, with no significant difference in mean urea reduction ratio between the Clearum high flux steam sterilized and Fresenius FX-series of dialyzers (p = 0.86). No dialyzer-related adverse events were reported in the study. ß-2-microglobulin reduction with the Clearum high flux steam sterilized dialyzer was statistically higher than the FX-series dialyzer (66.5% vs. 53.6%; p < 0.0001). Predialysis interleukin-6 and C-reactive protein concentrations, blood-rest scores (residual blood after blood restitution), and thrombin-anti-thrombin values were comparable. Albumin remained stable during the 6 weeks of Clearum high flux steam sterilized dialyzer use, with no appreciable differences compared to the Fresenius FX-series. CONCLUSION: The Clearum high flux steam sterilized dialyzer showed good mid-term effectivity for small and middle molecule removal with no reported dialyzer-related adverse events.

Highly luminescent and stable CsPbBr3 perovskite nanocrystals coated with polyethersulfone for white light-emitting diode applications.

Simultaneously improving the stability and photoluminescence quantum yield (PLQY) of all inorganic perovskite nanocrystals (NCs) is crucial for their practical utilization in various optoelectronic devices. Here, CsPbBr3 NCs coated with polyethersulfone (PES) were prepared via an in-situ co-precipitation method. The sulfone groups in PES bind to undercoordinated lead ion (Pb2+) on the CsPbBr3 NCs, resulting in significant reduction of surface defects, thus enhancing the PLQY from 74.2% to 88.3%. Meanwhile, the PES-coated NCs exhibit high water resistance and excellent heat and light stability, maintaining over 85% of the initial PL intensity under thermal aging (70°C, 4 h) and continuous 365 nm ultraviolet (UV) light irradiation (24 W, 8 h) conditions. By contrast, the PL intensity of the control NCs dramatically dropped to less than 40%. Finally, a diode emitting bright white light was fabricated utilizing the PES-coated CsPbBr3 NCs, which exhibits a color gamut of ~110% NTSC standard.

Polyethersulfone Polymer for Biomedical Applications and Biotechnology.

Polymers stand out as promising materials extensively employed in biomedicine and biotechnology. Their versatile applications owe much to the field of tissue engineering, which seamlessly integrates materials engineering with medical science. In medicine, biomaterials serve as prototypes for organ development and as implants or scaffolds to facilitate body regeneration. With the growing demand for innovative solutions, synthetic and hybrid polymer materials, such as polyethersulfone, are gaining traction. This article offers a concise characterization of polyethersulfone followed by an exploration of its diverse applications in medical and biotechnological realms. It concludes by summarizing the significant roles of polyethersulfone in advancing both medicine and biotechnology, as outlined in the accompanying table.

Comparative Study of Autogenic and Allogenic Chondrocyte Transplants on Polyethersulfone Scaffolds for Cartilage Regeneration.

The aim of this study was to evaluate the chondrogenic potential of chondrocyte transplants cultured in vitro on polyethersulfone (PES) membranes. Forty-eight rabbits (96 knee joints) were used in the project. The synthetic, macro-porous PES membranes were used as scaffolds. Fragments of articular cartilage were harvested from non-weight-bearing areas of the joints of the animals. Chondrocytes were isolated and then cultivated on PES scaffolds for 3 weeks. The animals were divided into four groups. All the lesions in the articular cartilage were full thickness defects. In Group I, autogenic chondrocytes on PES membranes were transplanted into the defect area; in Group II, allogenic chondrocytes on PES membranes were transplanted into the defect area; in Group III, pure PES membranes were transplanted into the defect area; and in Group IV, lesions were left untreated. Half of the animals from each group were terminated after 8 weeks, and the remaining half were terminated 12 weeks postoperatively. The samples underwent macroscopic evaluation using the Brittberg scale and microscopic evaluation using the O'Driscoll scale. The best regeneration was observed in Groups II and I. In Group I, the results were achieved with two surgeries, while in Group II, only one operation was needed. This indicates that allogenic chondrocytes do not require two surgeries, highlighting the importance of further in vivo studies to better understand this advantage. The success of the study and the desired properties of PES scaffolds are attributed mainly to the presence of sulfonic groups in the structure of the material. These groups, similar to chondroitin sulfate, which naturally occurs in hyaline cartilage, likely enable mutual affinity between the scaffold and cells and promote scaffold colonization by the cells.

Enhancing oil-water emulsion separation via synergistic filtration using graphene oxide-silver oxide nanocomposite-embedded polyethersulfone membrane.

This study introduces an innovative approach for enhancing oil-water emulsion separation using a polyethersulfone (PES) membrane embedded with a nanocomposite of graphene oxide (GO) and silver oxide (AgO). The composite membrane, incorporating PES and polyvinyl chloride (PVC), demonstrates improved hydrophilicity, structural integrity and resistance to fouling. Physicochemical characterization confirms successful integration of GO and AgO, leading to increased tensile strength, porosity and hydrophilicity. Filtration tests reveal substantial improvements in separating various oils from contaminated wastewater, with the composite membrane exhibiting superior efficiency and reusability compared to pristine PES membranes. This research contributes to the development of environmentally friendly oil-water separation methods with broad industrial applications.

A UV-Reflective Organic-Inorganic Tandem Structure for Efficient and Durable Daytime Radiative Cooling in Harsh Climates.

Radiative cooling shows great promise in eco-friendly space cooling due to its zero-energy consumption. For subambient cooling in hot humid subtropical/tropical climates, achieving ultrahigh solar reflectance (≥96%), durable ultraviolet (UV) resistance, and surface superhydrophobicity simultaneously is critical, which, however, is challenging for most state-of-the-art scalable polymer-based coolers. Here an organic-inorganic tandem structure is reported to address this challenge, which comprises a bottom high-refractive-index polyethersulfone (PES) cooling layer with bimodal honeycomb pores, an alumina (Al2 O3 ) nanoparticle UV reflecting layer with superhydrophobicity, and a middle UV absorption layer of titanium dioxide (TiO2 ) nanoparticles, thus providing thorough protection from UV and self-cleaning capability together with outstanding cooling performance. The PES-TiO2 -Al2 O3 cooler demonstrates a record-high solar reflectance of over 0.97 and high mid-infrared emissivity of 0.92, which can maintain their optical properties intact even after equivalent 280-day UV exposure despite the UV-sensitivity of PES. This cooler achieves a subambient cooling temperature up to 3 °C at summer noontime and 5 °C at autumn noontime without solar shading or convection cover in a subtropical coastal city, Hong Kong. This tandem structure can be extended to other polymer-based designs, offering a UV-resist but reliable radiative cooling solution in hot humid climates.

Efficacy and Safety of the Medium Cut-Off Elisio HX Dialyzer.

INTRODUCTION: The medium cut-off Elisio HX dialyzer by Nipro became commercially available in Europe in 2021, but there are still no reports of in vivo data. This study aimed to evaluate the safety and efficacy of it compared with previously evaluated hemodialysis (HD), expanded HD (HDx), and postdilution hemodiafiltration (HDF) treatments. METHODS: A prospective study was carried out on 18 patients who underwent 5 dialysis sessions: FX80 Cordiax in HD, Elisio H19 in HD, Elisio HX19 in HDx, Theranova 400 in HDx, and FX80 Cordiax in HDF. The reduction ratios of urea, creatinine, ß2-microglobulin, myoglobin, kappa FLC, prolactin, α1-microglobulin, α1-acid glycoprotein, lambda FLC, and albumin were compared. Dialysate albumin loss was measured. RESULTS: The comparison between the different dialysis modalities revealed no difference for small molecules, but HDx and HDF were significantly more efficient than HD for medium and large molecule removal. The efficacy of Elisio HX19 dialyzer in HDx was similar to the Theranova 400, superior to both dialyzers in HD, and slightly lower than HDF. Albumin losses in dialysate with HD dialyzers were less than 1 g, but between 1.5 and 2.5 g in HDx and HDF. The global removal score (GRS) values with HDx treatments were statistically significantly higher than those with HD. The highest GRS was obtained with the helixone dialyzer in HDF. CONCLUSIONS: The new MCO dialyzer, Elisio HX, performs with excellent behavior and tolerance. It represents an upgrade compared to their predecessor and is very close to the removal capacity of HDF treatment.

Preparation and Characterization of Polyethersulfone-Ultrafiltration Membrane Blended with Terbium-Doped Cerium Magnesium Aluminate: Analysis of Fouling Behavior.

In this study, various techniques, including X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS) mapping, X-ray photoelectron spectroscopy (XPS), and water-contact-angle goniometry (WCAG), were used to characterize the crystalline structure and morphological properties of terbium-doped cerium magnesium aluminate (Ce0.67Tb0.33MgAl11O19 or CMAT) in powder form. The results demonstrated that CMAT was successfully synthesized with a particle size of less than 5 µm and a fully evident distribution of elements, as revealed by the SEM images. This was further confirmed by the XRD and HRTEM images. XPS analysis confirmed the presence of all necessary components in CMAT. Additionally, WCAG results showed that the contact angle of CMAT was more hydrophilic with a value of 8.4°. To evaluate its performance, CMAT particles were dispersed in a Polyethersulfone (PES) solution and used to modify a PES ultrafiltration membrane through a phase-inversion method. The resulting membranes were characterized by SEM, atomic force microscopy (AFM), thermogravimetric analysis (TGA), WCAG, and permeability performance and fouling experiments. The addition of CMAT to the PES membranes did not have a significant effect on the structure of the SEM images of the top layer and cross-section of surface properties. However, increasing the concentration of CMAT improved the membrane surface roughness in AFM, and the modified membranes had the ability to resist fouling. The addition of CMAT did not lead to significant energy loss, indicating that the heat flux loss observed can indeed be explained by the amount of C-OH on the PES membrane's surface. The contact angle of the membranes became more hydrophilic with increasing concentration of CMAT from PES G0 to PES G7. The PES origin membrane showed a higher permeation than the membranes mixed with CMAT, and the modified membranes with CMAT displayed significant fouling resistance.

Scaffolds for Cartilage Tissue Engineering from a Blend of Polyethersulfone and Polyurethane Polymers.

In recent years, one of the main goals of cartilage tissue engineering has been to find appropriate scaffolds for hyaline cartilage regeneration, which could serve as a matrix for chondrocytes or stem cell cultures. The study presents three types of scaffolds obtained from a blend of polyethersulfone (PES) and polyurethane (PUR) by a combination of wet-phase inversion and salt-leaching methods. The nonwovens made of gelatin and sodium chloride (NaCl) were used as precursors of macropores. Thus, obtained membranes were characterized by a suitable structure. The top layers were perforated, with pores over 20 µm, which allows cells to enter the membrane. The use of a nonwoven made it possible to develop a three-dimensional network of interconnected macropores that is required for cell activity and mobility. Examination of wettability (contact angle, swelling ratio) showed a hydrophilic nature of scaffolds. The mechanical test showed that the scaffolds were suitable for knee joint applications (stress above 10 MPa). Next, the scaffolds underwent a degradation study in simulated body fluid (SBF). Weight loss after four weeks and changes in structure were assessed using scanning electron microscopy (SEM) and MeMoExplorer Software, a program that estimates the size of pores. The porosity measurements after degradation confirmed an increase in pore size, as expected. Hydrolysis was confirmed by Fourier-transform infrared spectroscopy (FT-IR) analysis, where the disappearance of ester bonds at about 1730 cm-1 wavelength is noticeable after degradation. The obtained results showed that the scaffolds meet the requirements for cartilage tissue engineering membranes and should undergo further testing on an animal model.

The effect of adding concentrated cheese whey prepared by ultrafiltration on the quality of Syrian bread.

The objective of this study is to evaluate the effect of adding two types cheese whey (W) contaning 0.9% protein and concentrated cheese whey (CW) containing 7.61% protein on the physical, chemical and sensory properties of Syrian bread. Concentrated whey samples were prepared using a UF membrane unit of 15 KDa at 25 °C and 4 bars. Both W and CW samples were added to wheat flour (72% extraction rate) at dilution level: 0, 25, 50, 75, and 100% levels. The effects of W and CW on dough rheology were evaluated using farinograph and alveograph parameters. The addition of 25% W or 50% CW improved the dough stability in the farinogram, as well as pressure and energy values in the alveogram. Significant increases were observed in ash, minerals (Ca, K, Mg, and P), and protein content (13.8%) when 50% CW was added to the dough. The results of sensory analysis showed that Syrian bread containing 25% whey (W) or 50% whey concentrate (CW) has achieved highest overall acceptability scores than control.

Photoaging of Baby Bottle-Derived Polyethersulfone and Polyphenylsulfone Microplastics and the Resulting Bisphenol S Release.

This study evaluated the release of bisphenol S (BPS) from polyethersulfone (PES) and polyphenylsulfone microplastics (MPs) derived from baby bottles under UV irradiation. Released BPS fluctuates over time because it undergoes photolysis under UV254 irradiation. Under UV365 irradiation, the highest released concentration at 50 °C was 1.7 and 3.2 times that at 35 and 25 °C, respectively, as the activation energy of the photochemical reactions responsible for MP decay was reduced at high temperatures. Low concentrations of humic acid (HA, ≤10 mg·L-1) promote BPS release because HA acts as a photosensitizer. A high concentration of HA (10∼50 mg·L-1) decreases the BPS release because HA shields MPs from light and scavenges reactive radicals that are produced via photochemical reactions. For example, under UV irradiation, hydroxyl radicals (•OH) attack results in the breakage of ether bonds and the formation of phenyl radicals (Ph•) and phenoxy radicals (Ph-O•).The•OH addition and hydrogen extractions further produce BPS from the decayed MPs. A leaching kinetics model was developed and calibrated by the experimental data. The calibrated model predicts the equilibrium level of BPS release from MPs that varies with the surface coverage density of BPS and leaching rate constants. This study provides groundwork that deepens our understanding of environmental aging and the chemical release of MPs.

Surface tuned polyethersulfone membrane using an iron oxide functionalized halloysite nanocomposite for enhanced humic acid removal.

Nanomodification of ultrafiltration (UF) membranes has been shown to be a simple and efficient technique for the preparation of high-performance membranes. In this work, an iron oxide functionalized halloysite nanoclay (Fe-HNC) nanocomposite was prepared and used as a nanofiller for polyethersulfone (PES) membranes. The effect of Fe-HNC concentration on the filtration performance of the membrane was investigated by varying the nanocomposite dosage (0-0.5 wt %) in the casting dope. Various characterization studies showed that the incorporation of Fe-HNC nanocomposites improved the membrane morphology and enhanced the surface properties, thermal stability, mechanical strength, hydrophilicity, and porosity. The permeability to pure water and filtration of humic acid (HA) were significantly improved by incorporating Fe-HNC into the PES membranes. The membrane with Fe-HNC loading of 0.1 wt % exhibited the highest pure water permeability (174.3 L/(m2 h bar)) and removal of HA (90.1 %), which were 1.8 times and 29 % higher, respectively than the pristine PES membrane. Moreover, fouling studies showed the enhanced antifouling ability of the Fe-HNC nanocomposites modified PES membranes, especially against irreversible fouling. Continuous membrane regeneration-based fouling removal studies from HA showed that the PES/0.1 wt % Fe-HNC membrane exhibited a high fouling recovery of 70.4 % with very low reversible and irreversible fouling resistance of 9.61 % and 14.78 %, respectively, compared to the pristine PES membrane (fouling recovery: 40.4 %; reversible fouling: 21.7 %; irreversible fouling: 20.1 %). Overall, the Fe-HNC nanocomposite proved to be an effective nanomodifier for improving the permeability of PES membranes and the antifouling ability to treat HA polluted aqueous streams.

Surface-engineered polyethersulfone membranes with inherent Fe-Mn bimetallic oxides for improved permeability and antifouling capability.

In recent years, bimetallic oxide nanoparticles have garnered significant attention owing to their salient advantages over monometallic nanoparticles. In this study, Fe2O3-Mn2O3 nanoparticles were synthesized and used as nanomodifiers for polyethersulfone (PES) ultrafiltration membranes. A NIPS was used to fabricate asymmetric membranes. The effect of nanoparticle concentration (0-1 wt.%) on the morphology, roughness, wettability, porosity, permeability, and protein filtration performance of the membranes was investigated. The membrane containing 0.25 wt% nanoparticles exhibited the lowest water contact angle (67°) and surface roughness (10.4 ± 2.8 nm) compared to the other membranes. Moreover, this membrane exhibited the highest porosity (74%) and the highest pure water flux (398 L/m2 h), which was 16% and 1.9 times higher than that of the pristine PES membrane. The modified PES membranes showed an improved antifouling ability, especially against irreversible fouling. Bovine serum albumin protein-based dynamic five-cycle filtration tests showed a maximum flux recovery ratio of 77% (cycle-1), 67% (cycle-2), and 65.8% (cycle-5) for the PES membrane containing 0.25 wt% nanoparticles. Overall, the biphasic Fe2O3-Mn2O3 nanoparticles were found to be an effective nanomodifier for improving the permeability and antifouling ability of PES membranes in protein separation and water treatment applications.

Efficient removal of lead ions from aqueous solution by graphene oxide modified polyethersulfone adsorptive mixed matrix membrane.

In this study, we report the combined effect of graphene oxide (GO) and polyvinylpyrrolidone (PVP) for the heavy metal removal efficiency of polyethersulfone (PES) membranes. PVP with four different amounts of GO was infused in the membrane matrix by the physical blending method. Characterizations such as porosity, contact angle, water flux and Fourier transform infrared spectroscopy were conducted for all prepared membranes. Viscid behavior of polymer dope solution was examined to understand the phase separation phenomena better. PVP enhanced the GO distribution within the membrane surface to some extent via hydrogen bond. The addition of nanoparticles enhanced the membrane physicochemical properties with water permeation, Pb2+ rejection and adsorption capacity. Permeate flux of modified membrane (m4) was found to be 150.21 L/m2h and it is 8.03 times higher than unmodified membrane (m0). Besides, all fabricated membranes were evaluated for Pb2+ rejection from synthetic wastewater and rejection % of m4 (80.6%) had increased twofold than m0 (38.9%). Membrane cleaning was performed using different methods and the best results were achieved with a concentration of 0.05 wt% sodium hypochlorite under pH 7 and further reused for the filtration test. Moreover, adsorption isotherm was tested using Freundlich and Langmuir models and the Langmuir model offered the best fitting.

Membrane surface roughness promotes rapid initial cell adhesion and long term microalgal biofilm stability.

In biofilm membrane photobioreactors development, conscientious works revolving around the effect of external environment factors on microalgal biofilm growth were assessed but more comparative research about the role of carrier surfaces properties such as surface roughness is necessary. Thus, commercial polyethersulfone (PES) membranes with two different molecular-weight-cut-offs (1 kDa and 30 kDa) were selected as the main representatives of surface roughness in a 20 days long-term biofilm cultivation experiment under dynamic flow condition for the biofilm evolvement of three benthic diatoms (Amphora coffeaeformis, Cylindrotheca fusiformis and Navicula incerta). Results depicted that rougher 30 kDa PES enable higher cell attachment degree for C. fusiformis (25.85 ± 2.75 × 109 cells m-2), followed by A. coffeaeformis (11.86 ± 2.76 × 109 cells m-2) and N. incerta (10.10 ± 0.65 × 109 cells m-2). Bounded extracellular polymeric substances (bEPS) gathered were relatively higher than soluble EPS (sEPS) while bEPS accumulated at least 10% higher on smooth 1 kDa PES than rough 30 kDa PES for the purpose of enhancing the biofilm disruption resistivity under liquid flow. Moreover, cell adhesion mechanism was proposed via computational fluid dynamics in parallel with EPS analysis. Copious amount of asperities and stagnant zones present on rough 30 kDa surfaces accelerated biofilm development and the consistency of the results have a great valence for interpretation of microalgal biofilm lifestyle on porous surfaces.

In-Plane Thermal Diffusivity Measurements of Polyethersulfone Woven Textiles by Infrared Thermography.

Lock-in thermography was applied to the measurement of the in-plane thermal diffusivity of three polyethersulfone (PES) textiles characterized by different weaving pattern as well as different mass density of interlacing fibers. The experimental results showed that the in-plane thermal diffusivity in each direction decreased with the increase of the fibers' linear mass density, thus leading to an anisotropic behavior of the thermal diffusivity in the specimen where PES fibers with different density were interlaced. A new theoretical model for the study of the heat diffusion in textiles was specifically developed and, thereafter, employed for the analysis of the experimental results. As such, our textile model approach, shedding light on the role of different textile and fibers parameters on the resulting thermal diffusivity, paves the way for the development and design of textiles with tailored thermal behavior.

Impact of Extractables/Leachables from Filter Materials on the Stability of Protein-Based Pharmaceutical Products.

The manufacturing of biopharmaceutical drug solutions can involve close contact with various polymeric components, including common filter membranes. Potential leachable substances from filters may interact with the protein and thereby increase the structural damage and aggregation. The main aim of the study deals with the assessment of extractable and leachable (E/L) from different filters and the potential effect of E/Ls on protein (human granulocyte-colony stimulating factor (rh-GCSF) stability. The present study examines the E/L profile of five different polymeric filter membranes using various chromatographic techniques including LC-MS and GC-MS. In order to investigate their effect on protein stability, G-CSF (human granulocyte colony-stimulating factor) formulations were spiked with filter leachable stock solutions at two different pH levels. The spiked formulations were further analyzed with respect to their aggregation behavior. The results demonstrated a higher E/L content in the case of polyamide (PA), polycarbonate (PC), and polyethersulfone (PES) filters as compared to the polytetrafluoroethylene (PTFE) and regenerative cellulose (RC) filter materials. The E/L from RC and PES was found surface-active, whereas E/L from PA and RC significantly altered the particle size/structure resulting in the aggregation of proteins. Furthermore, bisphenol A was found to be one of the E/L substances from PC filters and can impose significant health problems when administered along with pharmaceutical products. The present study reports a qualitative rank ordering of the filter membranes in terms of their propensity to generate E/Ls and thus can be helpful in selecting a suitable membrane filter.