Transepithelial Electrical Impedance Increase Following Porous Substrate Electroporation Enables Label-Free Delivery.

Porous substrate electroporation (PSEP) is a promising new method for intracellular delivery, yet fundamentals of PSEP are not well understood, especially the intermediate processes leading to delivery. PSEP is an electrical method, yet the relationship between PSEP and electrical impedance remains underexplored. In this study, a device capable of measuring impedance and performing PSEP is developed and the changes in transepithelial electrical impedance (TEEI) are monitored. These measurements show TEEI increases following PSEP, unlike other electroporation methods. The authors then demonstrate how cell culture conditions and electrical waveforms influence this response. More importantly, TEEI response features are correlated with viability and delivery efficiency, allowing prediction of outcomes without fluorescent cargo, imaging, or image processing. This label-free delivery also allows improved temporal resolution of transient processes following PSEP, which the authors expect will aid PSEP optimization for new cell types and cargos.

Integrated Catalyst-Substrate Electrodes for Electrochemical Water Splitting: A Review on Dimensional Engineering Strategy.

Water splitting (or, water electrolysis) is considered as a promising approach to produce green hydrogen and relieve the ever-increasing energy consumption as well as the accompanied environmental impact. Development of high-efficiency, low-cost practical water-splitting systems demands elegant design and fabrication of catalyst-loaded electrodes with both high activity and long-life time. To this end, dimensional engineering strategies, which effectively tune the microstructure and activity of electrodes as well as the electrochemical kinetics, play an important role and have been extensively reported over the past years. Here, a type of most investigated electrode configurations is reviewed, combining particulate catalysts with 3D porous substrates (aerogels, metal foams, hydrogels, etc.), which offer special advantages in the field of water splitting. It is analyzed the design principles, structural and interfacial characteristics, and performance of particle-3D substrate electrode systems including overpotential, cycle life, and the underlying mechanism toward improved catalytic properties. In particular, it is also categorized the catalysts as different dimensional particles, and show the importance of building hybrid composite electrodes by dimensional control and engineering. Finally, present challenges and possible research directions toward low-cost high-efficiency water splitting and hydrogen production is discussed.

Temperature-controlled microalgal biofilm detachment and harvesting assisted by ultrasonic from 3D porous substrates grafted with thermosensitive gels.

Microalgae have been renowned as the most promising energy organism with significant potential in carbon fixation. In the large-scale cultivation of microalgae, the 3D porous substrate with higher specific surface area is favorable to microalgae adsorption and biofilm formation, whereas difficult for biofilm detachment and microalgae harvesting. To solve this contradiction, N-isopropylacrylamide, a temperature-responsive gels material, was grafted onto the inner surface of the 3D porous substrate to form temperature-controllable interface wettability. The interfacial free energy between microalgae biofilm and the substrates increased from -63.02 mJ/m2 to -31.89 mJ/m2 when temperature was lowered from 32 °C to 17 °C, weakening the adsorption capacity of cells to the surface, and making the biofilm detachment ratio increased to 50.8%. When further cooling the environmental temperature to 4 °C, the detachment capability of microalgae biofilm kept growing. 91.6% of the cells in the biofilm were harvesting from the 3D porous substrate. And the biofilm detached rate was up to 19.84 g/m2/h, realizing the temperature-controlled microalgae biofilm harvesting. But, microalgae growth results in the secretion of extracellular polymeric substances (EPS), which enhanced biofilm adhesion and made cell detachment more difficult. Thus, ultrasonic vibration was used to reinforce biofilm detachment. With the help of ultrasonic vibration, microalgae biofilm detached rate increased by 143.45% to 41.07 g/m2/h. These findings provide a solid foundation for further development of microalgae biofilm detachment and harvesting technology.

Conformal atomic layer deposition of RuOxon highly porous current collectors for micro-supercapacitor applications.

3D porous electrodes have been considered as a new paradigm shift for increasing the energy storage of pseudocapacitive micro-supercapacitors for on-chip electronics. However, the conformal deposition of active materials is still challenging when highly porous structures are involved. In this work, we have investigated the atomic layer deposition (ALD) of ruthenium dioxide RuO2on porous Au and Pt architectures prepared by hydrogen bubble templated electrodeposition, with area enlargement factors ranging from 400 to 10 000 cm2/cm2. Using proper ALD conditions, a uniform RuO2coverage has been successfully obtained on porous Au, with a specific electrode capacitance of 8.1 mF cm-2and a specific power of 160 mW cm-2for a minute amount of active material. This study also shows the importance of the chemical composition and reactivity of the porous substrate for achieving conformal deposition of a ruthenium oxide layer.

Metallization of Porous Polyethylene Using a Wire-Arc Spray Process for Heat Transfer Applications.

Metallization of polyethylene (PE) using thermal spray techniques has proved difficult due to its low melting point and softness. In this study, metallic coatings were applied on porous polyethylene substrates using a twin wire-arc spray process. Commercially available polyethylene sheets, 3 mm in thickness, were used as substrates. Copper (Cu), aluminum (Al), and zinc (Zn) were successfully deposited on the porous polymer, without prior surface preparation, to form coatings with thickness of about 400 µm. Coating surface morphology and cross-sections were examined using a scanning electron microscope. Individual metal splats on the porous and non-porous substrates were observed to study the differences in the bonding mechanisms. The adhesion strength and electrical resistivity of the coatings on porous PE were evaluated. It was found that the bond strength of all three metallic coatings was found to be higher than the ultimate fracture strength of the porous. These results suggest that porosity in the polymer helps to overcome the challenges of metallizing polyethylene and provides a significant reduction in the weight of the polymer. Therefore, all these properties aided in fabricating an extremely lightweight, composite material with potential use in thermal management applications.

Quantification of Inkjet-Printed Pharmaceuticals on Porous Substrates Using Raman Spectroscopy and Near-Infrared Spectroscopy.

The use of inkjet printing for pharmaceutical manufacturing is gaining interest for production of personalized dosage forms tailored to specific patients. As part of the manufacturing, it is imperative to ensure that the correct dose is printed. The aim of this study was to use inkjet printing for manufacturing of personalized dosage forms combined with the use of near-infrared (NIR) and Raman spectroscopy as complementary analytical techniques for active pharmaceutical ingredient (API) quantification of the inkjet-printed dosage forms. Three APIs, propranolol (0.5-4.1 mg), montelukast (2.1-12.1 mg), and haloperidol (0.6-4.1 mg) were inkjet printed in 1 cm2 areas on a porous substrate. The printed doses were non-destructively analyzed by transmission NIR and Raman spectroscopy (both transmission and backscatter). X-ray computed microtomography (µ-CT) analysis was undertaken for porosity measurements of the substrate. The API content was confirmed using high-performance liquid chromatography (HPLC), and the content in the dosage forms was modeled from the NIR and Raman spectra using partial least squares regression (PLS). HPLC analysis revealed a linear correlation of the number of layers printed to the API content. The resulting PLS models for both NIR and Raman had R2 values between 0.95 and 0.99. The best predictive model was obtained using NIR, followed by Raman spectroscopy. µ-CT revealed the substrate to be highly porous and optimal for inkjet printing. In conclusion, NIR and Raman spectroscopic techniques could be used complementary as fast API quantification tools for inkjet-printed medicines.

A novel scale-down cell culture and imaging design for the mechanistic insight of cell colonisation within porous substrate.

At the core of translational challenges in tissue engineering is the mechanistic understanding of the underpinning biological processes and the complex relationships among components at different levels, which is a challenging task due to the limitations of current tissue culture and assessment methodologies. Therefore, we proposed a novel scale-down strategy to deconstruct complex biomatrices into elementary building blocks, which were resembled by thin modular substrate and then evaluated separately in miniaturised bioreactors using various conventional microscopes. In order to investigate cell colonisation within porous substrate in this proof-of-concept study, TEM specimen supporters (10-30 µm thick) with fine controlled open pores (100∼600 µm) were selected as the modular porous substrate and suspended in 3D printed bioreactor systems. Noninvasive imaging of human dermal fibroblasts cultured on these free-standing substrate using optical microscopes illustrated the complicated dynamic processes used by both individual and coordinated cells to bridge and segment porous structures. Further in situ analysis via SEM and TEM provided high-quality micrographs of cell-cell and cell-scaffold interactions at microscale, depicted cytoskeletal structures in stretched and relaxed areas at nanoscale. Thus this novel scaled-down design was able to improve our mechanistic understanding of tissue formation not only at single- and multiple-cell levels, but also at micro- and nanoscales, which could be difficult to obtain using other methods.

Growth and biomass productivity of Scenedesmus vacuolatus on a twin layer system and a comparison with other types of cultivations.

Scenedesmus is a genus of microalgae employed for several industrial uses. Industrial cultivations are performed in open ponds or in closed photobioreactors (PBRs). In the last years, a novel type of PBR based on immobilized microalgae has been developed termed porous substrate photobioreactors (PSBR) to achieve significant higher biomass density during cultivation in comparison to classical PBRs. This work presents a study of the growth of Scenedesmus vacuolatus in a Twin Layer System PSBR at different light intensities (600 µmol photons m-2 s-1 or 1000 µmol photons m-2 s-1), different types and concentrations of the nitrogen sources (nitrate or urea), and at two CO2 levels in the gas phase (2% or 0.04% v/v). The microalgal growth was followed by monitoring the attached biomass density as dry weight, the specific growth rate and pigment accumulation. The highest productivity (29 g m-2 d-1) was observed at a light intensity of 600 µmol photons m-2 s-1 and 2% CO2. The types and concentrations of nitrogen sources did not influence the biomass productivity. Instead, the higher light intensity of 1000 µmol photons m-2 s-1 and an ambient CO2 concentration (0.04%) resulted in a significant decrease of productivity to 18 and 10-12 g m-2 d-1, respectively. When compared to the performance of similar cultivation systems (15-30 g m-2 d-1), these results indicate that the Twin Layer cultivation System is a competitive technique for intensified microalgal cultivation in terms of productivity and, at the same time, biomass density.

Two-Ply Composite Membranes with Separation Layers from Chitosan and Sulfoethylcellulose on a Microporous Support Based on Poly(diphenylsulfone-N-phenylphthalimide).

Two-ply composite membranes with separation layers from chitosan and sulfoethylcellulose were developed on a microporous support based on poly(diphenylsulfone-N-phenylphthalimide) and investigated by use of X-ray diffraction and scanning electron microscopy methods. The pervaporation properties of the membranes were studied for the separation of aqueous alcohol (ethanol, propan-2-ol) mixtures of different compositions. When the mixtures to be separated consist of less than 15 wt % water in propan-2-ol, the membranes composed of polyelectrolytes with the same molar fraction of ionogenic groups (-NH3⁺ for chitosan and -SO3- for sulfoethylcellulose) show high permselectivity (the water content in the permeate was 100%). Factors affecting the structure of a non-porous layer of the polyelectrolyte complex formed on the substrate surface and the contribution of that complex to changes in the transport properties of membranes are discussed. The results indicate significant prospects for the use of chitosan and sulfoethylcellulose for the formation of highly selective pervaporation membranes.

Scaling up BiVO4 Photoanodes on Porous Ti Transport Layers for Solar Hydrogen Production.

Commercialization of photoelectrochemical (PEC) water-splitting devices requires the development of large-area, low-cost photoanodes with high efficiency and photostability. Herein, we address these challenges by using scalable fabrication techniques and porous transport layer (PTLs) electrode supports. We demonstrate the deposition of W-doped BiVO4 on Ti PTLs using successive-ionic-layer-adsorption-and-reaction methods followed by boron treatment and chemical bath deposition of NiFeOOH co-catalyst. The use of PTLs that facilitate efficient mass and charge transfer allowed the scaling of the photoanodes (100 cm2 ) while maintaining ~90 % of the performance obtained with 1 cm2 photoanodes for oxygen evolution reaction, that is, 2.10 mA cm-2 at 1.23 V vs. RHE. This is the highest reported performance to date. Integration with a polycrystalline Si PV cell leads to bias-free water splitting with a stable photocurrent of 208 mA for 6 h and 2.2 % solar-to-hydrogen efficiency. Our findings highlight the importance of photoelectrode design towards scalable PEC device development.

Zwitterion-functionalized nanofiber-based composite proton exchange membranes with superior ionic conductivity and chemical stability for direct methanol fuel cells.

Proton exchange membranes with high ionic conductivity and good chemical stability are critical for achieving high power density and long lifespan of direct methanol cells (DMFCs). Herein, a zwitterionic molecule was grafted onto the surface of polyvinylidene fluoride (PVDF) nanofibers to obtain functionalized PVDF porous substrate (SBMA-PDA@PVDF). Then, sulfonated poly(ether ether ketone) (SPEEK) was filled into the pores of SBMA-PDA@PVDF, and further ionic cross-linked via H2SO4 to prepare the composite membrane (SBMA-PDA@PVDF/SPEEK). The basic groups on the zwitterionic interface could not only establish ionic cross-linking with SPEEK to increase chemical stability and reduce swelling, but also serve as the adsorption sites for subsequent H2SO4 cross-linking to significantly enhance proton conductivity. Super-high proton conductivity (165.34 mS cm-1, 80 °C) was achieved for the membrane, which was 2.12 times higher than that of the pure SPEEK. Moreover, the SBMA-PDA@PVDF/SPEEK membrane exhibited remarkably improved oxidative stability of 91.6 % mass retention after soaking in Fenton's agent for 12 h, while pure SPEEK completely decomposed. Satisfactorily, the DMFC assembled with SBMA-PDA@PVDF/SPEEK exhibited a peak power density of 99.01 mW cm-2, which was twice as much as that of commercial Nafion 212 (48.88 mW cm-2). After 235 h durability test, only 11 % voltage loss was observed.

The Potential of Double-Faced Polyester-Viscose Woven Fabric as a Porous Substrate for Direct-Coating and Multilayer Concept.

Textile-based sensors fabricated using the direct-coating method are the appropriate choice to meet the aspects of flexibility, non-invasiveness, and lightness for continuous monitoring of the human body. The characteristics of the sensor substrate are directly influenced by factors such as the type of weave, thread fineness, fabric density, and the type of polymeric constituent fibers. The fabric used as the sensor substrate, fabricated using the direct-coating method, must be capable of retaining the electrode paste solution, which has higher viscosity, on one surface of the fabric to avoid short circuits during the fabrication process. However, during its application, this fabric should allow the easy passage of analyte solutions with low viscosity as much as possible. Hence, an appropriate fabric construction is required to serve as the substrate for textile-based sensors to ensure the success of the fabrication process and the effectiveness of the resulting sensor's performance. The development of the structural design of the fabric to be used as a substrate for non-invasive biosensors with a multilayer concept is carried out by weaving and sewing processes utilizing polyester-viscose fibers. During the production process, variations are applied, such as weft yarn density, the characterization of wetting time, absorption rate, maximum wetted radius, spreading speed, and accumulative one-way transport index. The most suitable fabric for use as a substrate for non-invasive biosensors with a multilayer concept, such as in this research, is a fabric with a weft thread density of 70 strands per inch, along with the addition of an analyte transfer thread configuration.

Potential of Porous Substrate Bioreactors for Removal of Pollutants from Wastewater Using Microalgae.

Porous substrate bioreactors (PSBRs) are a new technology to grow microalgae immobilized in a dense culture and solve some problems linked to suspended cultivation. During recent years, this technology has been used in laboratory and pilot setups in different fields of environmental biotechnology, such as wastewater treatment. The aim of this short review is to introduce the PSBR technology, summarize the results obtained in removing some pollutants from wastewater, provide an assessment of the potential of PSBRs for wastewater treatment, and the subsequent use of the algal biomass for other purposes.

Transepithelial Electrical Impedance Increase Following Porous Substrate Electroporation Enables Label-Free Delivery.

Porous substrate electroporation (PSEP) is a promising new method for intracellular delivery, yet fundamentals of the PSEP delivery process are not well understood, partly because most PSEP studies rely solely on imaging for evaluating delivery. Although effective, imaging alone limits understanding of intermediate processes leading to delivery. PSEP is an electrical process, so electrical impedance measurements naturally complement imaging for PSEP characterization. In this study, we developed a device capable of measuring impedance and performing PSEP and we monitored changes in transepithelial electrical impedance (TEEI). Our measurements show TEEI increases following PSEP, unlike other electroporation methods. We then demonstrated how cell culture conditions and electrical waveforms influence this response. More importantly, we correlated TEEI response features with viability and delivery efficiency, allowing prediction of outcomes without fluorescent cargo, imaging, or image processing. This label-free delivery also allows improved temporal resolution of transient processes following PSEP, which we expect will aid PSEP optimization for new cell types and cargos.

Thin film liquid-vapor phase change phenomena over nano-porous substrates: A molecular dynamics perspective.

Surfaces with nano-pores have significant effect in enhancing heat transfer during phase change process. In this study, Molecular dynamics simulations have been performed to investigate thin film evaporation over different nano-porous substrate. The molecular system consists of argon as the working fluid and Platinum as the solid substrate. To study the effect of the nano-pores in phase change process, the nano-porous substrates had been structured with four different hexagonal porosity with three different heights. The structures of the hexagonal nano-pore were characterized through variation of void fraction as well as height to arm thickness ratio. Qualitative heat transfer performance has been characterized by closely monitoring the temporal variation of temperature and pressure, net evaporation number, wall heat flux of the system for all cases under consideration. The quantitative characterization of heat and mass transfer performance has been done by calculating the average heat flux and evaporative mass flux. Diffusion coefficient of argon is also evaluated to illustrate the effect of these nano-porous substrate in enhancing the movement of argon atoms thus heat transfer. It has been found that the presence of hexagonal nano-porous substrates significantly increases heat transfer performance. Structures with lower void fraction offers better enhancement of heat flux and other transport characteristics. Increment in nano-pores height also significantly enhances heat transfer. Present study clearly points out the noteworthy role associated with nano-porous substrate in modulating heat transfer characteristics during liquid-vapor phase change phenomena both from qualitative and quantitative perspectives.

Permeation Properties of Water Vapor through Graphene Oxide/Polymer Substrate Composite Membranes.

Graphene oxide (GO) has attracted attention as an excellent membrane material for water treatment and desalination owing to its high mechanical strength, hydrophilicity, and permeability. In this study, composite membranes were prepared by coating GO on various polymeric porous substrates (polyethersulfone, cellulose ester, and polytetrafluoroethylene) using suction filtration and casting methods. The composite membranes were used for dehumidification, that is, water vapor separation in the gas phase. GO layers were successfully prepared via filtration rather than casting, irrespective of the type of polymeric substrate used. The dehumidification composite membranes with a GO layer thickness of less than 100 nm showed a water permeance greater than 1.0 × 10-6 mol/(m2 s Pa) and a H2O/N2 separation factor higher than 104 at 25 °C and 90-100% humidity. The GO composite membranes were fabricated in a reproducible manner and showed stable performance as a function of time. Furthermore, the membranes maintained high permeance and selectivity at 80°C, indicating that it is useful as a water vapor separation membrane.

Effect of LED Illumination Cycle and Carbon Sources on Biofilms of Haematococcus pluvialis in Pilot-Scale Angled Twin-Layer Porous Substrate Photobioreactors.

Light-emitting diodes are increasingly used as artificial light sources in Haematococcus pluvialis cultivation due to the fact of their energy advantages. The immobilized cultivation of H. pluvialis in pilot-scale angled twin-layer porous substrate photobioreactors (TL-PSBRs) was initially performed with a 14/10 h light/dark cycle and showed relatively low biomass growth and astaxanthin accumulation. In this study, the illumination time with red and blue LEDs at a light intensity of 120 µmol photons m-2 s-1 was increased to 16-24 h per day. With a light/dark cycle of 22/2 h, the biomass productivity of the algae was 7.5 g m-2 day-1, 2.4 times higher than in the 14/10 h cycle. The percentage of astaxanthin in the dry biomass was 2%, and the total amount of astaxanthin was 1.7 g m-2. Along with the increase in light duration, adding 10 or 20 mM NaHCO3 to the BG11-H culture medium over ten days of cultivation in angled TL-PSBRs did not increase the total amount of astaxanthin compared with only CO2 addition at a flow rate of 3.6 mg min-1 to the culture medium. Adding NaHCO3 with a 30-80 mM concentration inhibited algal growth and astaxanthin accumulation. However, adding 10-40 mM NaHCO3 caused algal cells to accumulate astaxanthin at a high percentage in dry weight after the first four days in TL-PSBRs.

An equivalent circuit model for localized electroporation on porous substrates.

In vitro intracellular delivery is a fundamental challenge with no widely adopted methods capable of both delivering to millions of cells and controlling that delivery to a high degree of accuracy. One promising method is porous substrate electroporation (PSEP), where cells are cultured on porous substrates and electric fields are used to permeabilize discrete portions of the cell membrane for delivery. A major obstacle to the widespread use of PSEP is a poor understanding of the various impedances that constitute the system, including the impedances of the porous substrate and the cell monolayer, and how these impedances are influenced by experimental parameters. In response, we used impedance measurements to develop an equivalent circuit model that closely mimics the behavior of each of the main components of the PSEP system. This circuit model reveals for the first time the distribution of voltage across the electrode-electrolyte interface impedances, the channels of the porous substrate, the cell monolayer, and the transmembrane potential during PSEP. We applied sample waveforms through our model to understand how waveforms can be improved for future studies. Our model was validated from intracellular delivery of protein using PSEP.

Effect of nanodisperse powders on the spreading and crystallization of a metal drop on a porous substrate.

The influence of modifying nanopowders on the spreading and crystallization of a nickel droplet on a porous steel substrate is analyzed. For this purpose, a model has been developed for the spreading of a drop of liquid metal after its high-speed collision with a heated porous substrate. Due to the high impact velocity, the process of metal crystallization is considered after the complete spreading of the drop using the model of heterogeneous nucleation and macroscopic growth of the solid phase, taking into account the size and capillary effects. The influence of the impact velocity and substrate porosity on the thickness and diameter of the formed splat, the penetration depth, and the volume of liquid that penetrated the substrate has been studied. The numerical study of heterogeneous crystallization of a metal drop has made it possible to evaluate the influence of the modifying nanoparticle parameters, the impact velocity, and substrate porosity on the heterogeneous nucleation and on the resulting splat macrostructure.

A New Class of Electronic Devices Based on Flexible Porous Substrates.

With the advent of the Internet of Things era, the connection between electronic devices and humans is getting closer and closer. New-concept electronic devices including e-skins, nanogenerators, brain-machine interfaces, and implantable medical devices, can work on or inside human bodies, calling for wearing comfort, super flexibility, biodegradability, and stability under complex deformations. However, conventional electronics based on metal and plastic substrates cannot effectively meet these new application requirements. Therefore, a series of advanced electronic devices based on flexible porous substrates (e.g., paper, fabric, electrospun nanofibers, wood, and elastic polymer sponge) is being developed to address these challenges by virtue of their superior biocompatibility, breathability, deformability, and robustness. The porous structure of these substrates can not only improve device performance but also enable new functions, but due to their wide variety, choosing the right porous substrate is crucial for preparing high-performance electronics for specific applications. Herein, the properties of different flexible porous substrates are summarized and their basic principles of design, manufacture, and use are highlighted. Subsequently, various functionalization methods of these porous substrates are briefly introduced and compared. Then, the latest advances in flexible porous substrate-based electronics are demonstrated. Finally, the remaining challenges and future directions are discussed.