RESUMO
Transparent solar cells (TSCs) hold substantial potential as continuous energy generators, enabling their use in situations where conventional devices may not be feasible. However, research aimed at modularizing TSCs for the purpose of regulating the overall voltage and current they produce, a critical step toward practical application, is still in its nascent stages. In this study, we explored a custom-designed, all-back-contact (ABC) configuration, which situates all electrical contacts on the rear side, to create glass-like transparent crystalline silicon (c-Si) solar cells and seamless modules. The ABC design not only demonstrates high power conversion efficiency (PCE) in solar cells but also ensures unobstructed visibility through transparent solar modules. Notably, ABC-transparent c-Si solar cells achieved a peak PCE of 15.8% while maintaining an average visible transmittance of 20%. Through seamlessly interconnecting the unit cells, the output voltage and power were systematically tuned from 0.64 V and 15.8 mW (for a 1 cm2-sized unit cell) to 10.0 V and 235 mW (for a 16 cm2-sized module). Furthermore, we successfully demonstrated the photocharging of a smartphone using a transparent ABC solar module.
RESUMO
For organic photovoltaic (OPV) devices to achieve consistent performance and long operational lifetimes, organic semiconductors must be processed with precise control over their purity, composition, and structure. This is particularly important for high volume solar cell manufacturing where control of materials quality has a direct impact on yield and cost. Ternary-blend OPVs containing two acceptor-donor-acceptor (A-D-A)-type nonfullerene acceptors (NFAs) and a donor have proven to be an effective strategy to improve solar spectral coverage and reduce energy losses beyond that of binary-blend OPVs. Here, we show that the purity of such a ternary is compromised during blending to form a homogeneously mixed bulk heterojunction thin film. We find that the impurities originate from end-capping C=C/C=C exchange reactions of A-D-A-type NFAs, and that their presence influences both device reproducibility and long-term reliability. The end-capping exchange results in generation of up to four impurity constituents with strong dipolar character that interfere with the photoinduced charge transfer process, leading to reduced charge generation efficiency, morphological instabilities, and an increased vulnerability to photodegradation. As a consequence, the OPV efficiency falls to less than 65% of its initial value within 265 h when exposed to up to 10 suns intensity illumination. We propose potential molecular design strategies critical to enhancing the reproducibility as well as reliability of ternary OPVs by avoiding end-capping reactions.
RESUMO
Perovskite materials, particularly FAPbI3, have emerged as promising candidates for solar energy conversion applications. However, these materials are plagued by well-known defects and suboptimal film quality. Enhancing crystallinity and minimizing defect density are therefore essential steps in the development of high-performance perovskite solar cells. In this study, 1H-Pyrazole-1-carboximidamide hydrochloride (PCH) is introduced into FAPbI3 perovskite films. The molecular structure of PCH features a pyrazole ring bonded to formamidine (FA). The FA moiety of PCH facilitated the incorporation of this additive into the film lattice, while the negatively charged pyrazole ring effectively passivated positively charged iodine vacancies. The presence of PCH led to the fabrication of an FAPbI3 device with improved crystallinity, a smoother surface, and reduced defect density, resulting in enhanced Voc and fill factor. A record power conversion efficiency of 24.62% is achieved, along with exceptional stability under prolonged air exposure and thermal stress. The findings highlight the efficacy of PCH as a novel additive for the development of high-performance perovskite solar cells.
RESUMO
PbS quantum dot (QD) solar cells harvest near-infrared solar radiation. Their conventional hole transport layer has limited hole collection efficiency due to energy level mismatch and poor film quality. Here, how to resolve these two issues by using Ag-doped PbS QDs are demonstrated. On the one hand, Ag doping relieves the compressive stress during layer deposition and thus improves film compactness and homogeneity to suppress leakage currents. On the other hand, Ag doping increases hole concentration, which aligns energy levels and increases hole mobility to boost hole collection. Increased hole concentration also broadens the depletion region of the active layer, decreasing interface charge accumulation and promoting carrier extraction efficiency. A champion power conversion efficiency of 12.42% is achieved by optimizing the hole transport layer in PbS QD solar cells, compared to 9.38% for control devices. Doping can be combined with compressive strain relief to optimize carrier concentration and energy levels in QDs, and even introduce other novel phenomena such as improved film quality.
RESUMO
Although the atmospheric stability of lead-free inorganic double perovskite (DP) solar cells (PSCs) looks promising, their further development is hampered by inadequate film quality and non-radiative carrier recombination at the interfaces. Herein, the incorporation of a newly developed intriguing class of 2D material Ti3C2Tx MXene nanosheets with the photo-absorbing Cu2AgBiI6 (CABI) active layer of a fully inorganic solar cell is reported. The highly conductive Ti3C2Tx nanosheets work as a multi-functional additive by tuning the band gap, reducing the non-radiative carrier recombination, and inhibiting carrier accumulation. In addition, the presence of Ti3C2Tx MXene increases the surface free energy of the perovskite film, which elevates the energy barrier for nucleation and realizes a highly crystalline CABI perovskite film. Primarily, the MXene modification accelerates the charge extraction and transport at the interfaces of the active layer, utilizing energy level alignment with the charge transport layers. Consequently, the photo-conversion efficiency (PCE) of the device with MXene is substantially enhanced to 1.50%. Moreover, the 2D Ti3C2Tx nanosheets increased the long-term stability of the devices by retaining 70% of the initial PCE after 1680 h. With regard to relieving the severe carrier recombination at the interfaces, this work sets a new paradigm toward imminent solar energy conversion.
RESUMO
Luminescent coupling (LC) is a key phenomenon in monolithic tandem solar cells. This study presents a nondestructive technique to quantitatively evaluate the LC effect, addressing a gap in the existing predictions made by optical modeling. The method involves measuring the ratio of photons emitted from the high bandgap top cell that escape through the rear, contributing additional current to the bottom cell, and to those escaping from the front side of top cell. The findings indicate that in the analyzed monolithic perovskite/silicon tandem solar cells, more than 85% of the emitted photons escaping from the perovskite top cell are used to generate additional current in the bottom cell. This process notably reduces the mismatch in the generated current between each subcell, particularly when the current is limited by the low bandgap subcell. The presented method is applicable to a variety of monolithic tandem structures, providing vital information for subcell characterization, providing vital information for predicting energy output and optimization for outdoor applications.
RESUMO
Atomic layer deposition (ALD) growth of conformal thin SnOx films on perovskite absorbers offers a promising method to improve carrier-selective contacts, enable sputter processing, and prevent humidity ingress toward high-performance tandem perovskite solar cells. However, the interaction between perovskite materials and reactive ALD precursor limits the process parameters of ALD-SnOx film and requires an additional fullerene layer. Here, it demonstrates that reducing the water dose to deposit SnOx can reduce the degradation effect upon the perovskite underlayer while increasing the water dose to promote the oxidization can improve the electrical properties. Accordingly, a SnOx buffer layer with a gradient composition structure is designed, in which the compositionally varying are achieved by gradually increasing the oxygen source during the vapor deposition from the bottom to the top layer. In addition, the gradient SnOx structure with favorable energy funnels significantly enhances carrier extraction, further minimizing its dependence on the fullerene layer. Its broad applicability for different perovskite compositions and various textured morphology is demonstrated. Notably, the design boosts the efficiencies of perovskite/silicon tandem cells (1.0 cm2) on industrially textured Czochralski (CZ) silicon to a certified efficiency of 28.0%.
RESUMO
In inverted perovskite solar cells, conventional planar 2D/3D perovskite heterojunctions typically exhibit a type-II band alignment, where the electric field tends to drive the electron motion in the opposite direction to the direction of electron transfer. Here, a 2D/3D gradient heterojunction is developed by allowing the 2D perovskite to infiltrate the 3D perovskite surface along the grain boundaries using the interaction between the organic cation of the 2D perovskite and the pseudohalogen thiocyanate ion (SCN-), which has the ability to diffuse downward. The infiltrated 2D perovskite not only fills the gaps of grain boundaries with improved structural stability, but it also reconstructs the original landscape of the electric field toward the n-doped surface to enable more rapid electron transfer and weaken the adverse type-II band alignment effect. Since 2D perovskite seals the GBs, the nonvolatile SCN- can accumulate at the top and bottom dual interfaces, releasing residual stress and significantly inhibiting nonradiative recombination. The device exhibits an excellent efficiency of 24.76% (certified 24.29%) and long-term stability that is >90% of the original PCE value after 800 h of heating at 85 °C or in high humidity (≈65%).
RESUMO
Passivating the electronic defects of metal halide perovskite is regarded as an effective way to improve the power conversion efficiency (PCE) of perovskite solar cells (PVSCs). Here, a series of dipeptide molecules with abundant âCâO, âOâ and âNH functional groups as defects passivators for perovskite films are employed. These dipeptide molecules are utilized to treat the surface of prototype methyl ammonium lead iodide (MAPbI3) films and the corresponding PVSCs exhibit enhanced photovoltaic performance and ambient stability, which can be ascribed to: 1) the âCâO and âOâ can interact with the undercoordinated Pb2+ ions and the âNH groups can form hydrogen bonds with the I- ions, passivating the defects in perovskite film and reducing charge recombination in PVSCs; 2) the long alkyl chain of dipeptide molecules increases the hydrophobicity of the perovskite surface and thus enhance the stability of PVSCs. The passivated MAPbI3-based PVSCs exhibit a champion PCE of 20.3% and retain 60% of the initial PCE after 1000 h. It is believed that the defects passivation engineering using polypeptide moleculars can be applied in other perovskite compositions for high device efficiency and stability.
RESUMO
Blade-coating stands out as an alternative for fabricating scalable perovskite solar cells. However, it demands special control of the precursor composition regarding nucleation and crystallization and currently exhibits lower performance than the spin-coating process. It is mainly the resulting film morphology and excess lead iodide (PbI2) distribution that influences the optoelectronic properties. Here, the effectiveness of introducing N-Methyl-2-pyrrolidone (NMP) to regulate the structure of the perovskite layer and the redistribution of PbI2 is found. The introduction of NMP leads to the accumulation of excess PbI2, mainly on the top surface, reducing residual PbI2 at the perovskite buried interface. This not only facilitates the passivation of perovskite grain boundaries but also eliminates the potential degradation of the PbI2 triggered by light illumination in the perovskite buried interface. The optimized NMP-modified inverted perovskite solar cell achieves a champion efficiency of 24.5%, among the highest reported blade-coated perovskite solar cells. Furthermore, 13.68 cm2 blading perovskite solar modules are fabricated and demonstrate an efficiency of up to 20.4%. These findings underscore that with proper modulation of precursor composition, blade-coating can be a feasible and superior alternative for manufacturing high-quality perovskite films, paving the way for their large-scale applications in photovoltaic technology.
RESUMO
Sodium (Na) doping is a well-established technique employed in chalcopyrite and kesterite solar cells. While various improvements can be achieved in crystalline quality, electrical properties, or defect passivation of the absorber materials by incorporating Na, a comprehensive demonstration of the desired Na distribution in CZTSSe is still lacking. Herein, a straightforward Na doping approach by dissolving NaCl into the CZTS precursor solution is proposed. It is demonstrated that a favorable Na ion distribution should comprise a precisely controlled Na+ concentration at the front surface and an enhanced distribution within the bottom region of the absorber layer. These findings demonstrated that Na ions play several positive roles within the device, leading to an overall power conversion efficiency of 12.51%.
RESUMO
Inverted flexible perovskite cells (fPSCs) have attracted much attention for their high efficiency and power per weight. Still, the steady-state output is one of the critical factors for their commercialization. In this paper, it is found that the steady-state current of inverted fPSCs based on nickel oxide nanoparticles (n-NiOx) continuously decreases under light illumination. Conversely, those based on magnetron-sputtered NiOx (sp-NiOx) exhibit the opposite result. Based on visualization of ion migration in the photoluminescence (PL) imaging microscopy tests, the discrepancies in the buried surfaces lead to the differences in ion migration in perovskite films, which triggers the temporary instability of the output current of devices during operation. The DFT theoretical calculation and experimental results reveal that NiOx films with different contents of Ni vacancies can modulate the crystallization of the perovskite films on the NiOx surfaces. Tuning the crystallization of the perovskite films is essential to stabilize the output current of fPSCs at a steady state. To demonstrate that, capsaicin is doped into the perovskite solutions to improve the quality of the perovskite buried interface. Finally, the corresponding fPSCs exhibit outstanding efficiency and stability during operation. These results provide valuable scientific guidance for fabricating fPSCs with stable operation under illumination conditions.
RESUMO
Metal halide perovskite solar cells have achieved tremendous progress and have attracted enormous research and development efforts since the first report of demonstration in 2009. Due to fabrication versatility, many heat treatment methods can be utilized to achieve perovskite film crystallization. Herein, 10.6 µm carbon dioxide laser process is successfully developed for the first time for perovskite film crystallization. In addition, this is the first time formamidinium lead triiodide solar cells by laser annealing under ambient are demonstrated. The champion cell produces a power conversion efficiency of 21.8%, the highest for laser-annealed perovskite cells. And this is achieved without any additive, passivation, or post-treatment.
RESUMO
2D conjugated extension on central units of small molecular acceptors (SMAs) has gained great successes in reaching the state-of-the-art organic photovoltaics. Whereas the limit size of 2D central planes and their dominant role in constructing 3D intermolecular packing networks are still elusive. Thus, by exploring a series of SMAs with gradually enlarged central planes, it is demonstrated that, at both single molecular and aggerated levels, there is an unexpected blue-shift for their film absorption but preferable reorganization energies, exciton lifetimes and binding energies with central planes enlarging, especially when comparing to their Y6 counterpart. More importantly, the significance of well-balanced molecular packing modes involving both central and end units is first disclosed through a systematic single crystal analysis, indicating that when the ratio of central planes area/end terminals area is no more than 3 likely provides a preferred 3D intermolecular packing network of SMAs. By exploring the limit size of 2D central planes, This work indicates that the structural profiles of ideal SMAs may require suitable central unit size together with proper heteroatom replacement instead of directly overextending 2D central planes to the maximum. These results will likely provide some guidelines for future better molecular design.
RESUMO
"Perovskite / Carbon" interface has remained a key bottleneck for the hole-conductor-free perovskite solar cells based on carbon-electrode (CPSCs), due to problems like loose physics contact, defects, energy mismatch, poor chemical coupling, etc. A previous study shows that octylammonium iodide (OAI) blending in carbon paste induced a kind of "in-situ healing" effect for "perovskite / carbon" interface, and improved power conversion efficiency from ≈13% to >19%. Here the beneath mechanism is further explored by careful examination of the interaction between OAI molecule and carbon black (CB) nanoparticles. It comes to show that, the famous "CB adsorption" plays a key role during the "healing" processes. Due to CB adsorption behavior, the mass ratio between OAI and CB influences much on the healing effect. By suitably adjusting the mass ratio between OAI and CB, and increasing the light harvest of perovskite, an efficiency of 19.41% is achieved for the hole-conductor-free CPSCs. Device efficiency and the charge-extraction and recombination process are tracked with the storage period, continuous improvement appears for devices assembled by relatively higher CB mass. A kind of "slow-release effect" is revealed during the OAI-induced "in-situ healing" process, which is caused by the famous "CB adsorption" behavior.
RESUMO
Despite CsPbI2.75Br0.25 inorganic perovskites exhibit high potential for single-junction and/or tandem solar cells, unexpected non-radiative recombination, and mismatched interfacial band alignment within the inorganic perovskite solar cells (PSCs) disadvantageously affect their photovoltaic performance. Rational design of the dipole shielding layer (DSL) is vital to realize a win-win situation for the defect passivation and band alignment. Herein, A-site dipole molecules, that is, neopentylamine and 2-methylbutylamine, are employed for in-situ self-assembly of a thus-far unreported DSL at the interface between 3D perovskite and hole transport layer. The as-prepared DSL demonstrates a 2D RP phase perovskite and the lattice-matching structurally-stable DSL@3D perovskite enables to alleviate the unexpected surface defects and suppress the spontaneous non-radiative recombination by means of effectively tuning the surface work function via regulating the dipole moment length and Van der Waals gap. Accordingly, the top dipole-modified inorganic PSCs exhibit a champion power conversion efficiency (PSC) as high as 19.77% and a fill factor over 83%. Equally importantly, the corresponding solar cells demonstrate a remarkable enhanced stability, maintaining 90% of its initial efficiency for more than 1200 h without encapsulation under a 20% ± 5% relative humidity.
RESUMO
Perovskite solar cells, recognized for their high photovoltaic conversion efficiency (PCE), cost-effectiveness, and simple fabrication, face challenges in PCE improvement due to structural defects in polycrystalline films. This study introduces a novel fabrication method for perovskite films using methylammonium chloride (MACl) to align grain orientation uniformly, followed by a high-pressure process to merge these grains into a texture resembling single-crystal perovskite. Employing advanced visual fluorescence microscopy, charge dynamics in these films are analyzed, uncovering the significant impact of grain boundaries on photo-generated charge transport within perovskite crystals. A key discovery is that optimal charge transport efficiency and speed occur in grain centers when the grain size exceeds 10 µm, challenging the traditional view that efficiency peaks when grain size surpasses film thickness to form a monolayer. Additionally, the presence of large-sized grains enhances ion activation energy, reducing ion migration under light and improving resistance to photo-induced degradation. In application, a perovskite solar cell module with large grains achieve a PCE of 22.45%, maintaining performance with no significant degradation under continuous white LED light at 100 mA cm-2 for over 1000 h. This study offers a new approach to perovskite film fabrication and insights into optimizing perovskite solar cell modules.
RESUMO
The advancement of acceptors plays a pivotal role in determining photovoltaic performance. While previous efforts have focused on optimizing acceptor-donor-acceptor1-donor-acceptor (A-DA1-D-A)-typed acceptors by adjusting side chains, end groups, and conjugated extension of the electron-deficient central A1 unit, the systematic exploration of the impact of peripheral aryl substitutions, particularly with different electron groups, on the A1 unit and its influence on device performance is still lacking. In this study, three novel acceptors - QxTh, QxPh, and QxPy - with distinct substitutions on the quinoxaline (Qx) are designed and synthesized. Density functional theory (DFT) analyses reveal that QxPh, featuring a phenyl-substituted Qx, exhibits the smallest molecular binding energies and a tightest π···π stacking distance. Consequently, the PM6:QxPh device demonstrates a better power conversion efficiency (PCE) of 17.1% compared to the blends incorporating QxTh (16.4%) and QxPy (15.7%). This enhancement is primarily attributed to suppressed charge recombination, improved charge extraction, and more favorable molecular stacking and morphology. Importantly, introducing QxPh as a guest acceptor into the PM6:BTP-eC9 binary system yields an outstanding PCE of 19.5%, indicating the substantial potential of QxPh in advancing ternary device performance. The work provides deep insights into the expansion of high-performance organic photovoltaic materials through peripheral aryl substitution strategy.
RESUMO
Tin-halide perovskites (THP) are emerging materials for photovoltaics with optoelectronic properties potentially rivaling lead-based analoges. Their efficiencies in solar cells are, however, severely limited by the high sensitivity of tin to oxygen and the heavy p-doping natively present in the material. While the effects of oxygen can be mitigated by using reducing agents upon the synthesis and by encapsulating the device, the native p-doping caused by the high density of acceptor defects remains a challenge to be further addressed for prolonging carrier lifetimes and, consequently, device efficiency. In this work, potential compositional engineering strategies aimed at reducing the p-doping of this class of materials and increasing their efficiency in solar cells are investigated. Based on density functional theory simulations it is demonstrated that THP doping with d1s2 trivalent ions effectively decreases the hole background density and the density of the deep defects responsible for the non-radiative recombination in these materials. This effect is enhanced by alloying iodide with small fractions of bromide, up to 33%. Higher bromide fractions, instead, are detrimental due to the increased non-radiative recombination. These results may provide useful guidelines to experimentalists for improving the optoelectronic quality of THPs and consequently of the ensuing devices.
RESUMO
Nickel oxide (NiOx) is commonly used as a holetransporting material (HTM) in p-i-n perovskite solar cells. However, the weak chemical interaction between the NiOx and CH3NH3PbI3 (MAPbI3) interface results in poor crystallinity, ineffective hole extraction, and enhanced carrier recombination, which are the leading causes for the limited stability and power conversion efficiency (PCE). Herein, two HTMs, TRUX-D1 (N2,N7,N12-tris(9,9-dimethyl-9H-fluoren-2-yl)-5,5,10,10,15,15-hexaheptyl-N2,N7,N12-tris(4-methoxyphenyl)-10,15-dihydro-5H-diindeno[1,2-a:1',2'-c]fluorene-2,7,12-triamine) and TRUX-D2 (5,5,10,10,15,15-hexaheptyl-N2,N7,N12-tris(4-methoxyphenyl)-N2,N7,N12-tris(10-methyl-10H-phenothiazin-3-yl)-10,15-dihydro-5H-diindeno[1,2-a:1',2'-c]fluorene-2,7,12-triamine), are designed with a rigid planar C3 symmetry truxene core integrated with electron-donating amino groups at peripheral positions. The TRUX-D molecules are employed as effective interfacial layer (IFL) materials between the NiOx and MAPbI3 interface. The incorporation of truxene-based IFLs improves the quality of perovskite crystallinity, minimizes nonradiative recombination, and accelerates charge extraction which has been confirmed by various characterization techniques. As a result, the TRUX-D1 exhibits a maximum PCE of up to 20.8% with an impressive long-term stability. The unencapsulated device retains 98% of their initial performance following 210 days of aging in a glove box and 75.5% for the device after 80 days under ambient air condition with humidity over 40% at 25 °C.