Hydrogen Confinement in Hexagonal Boron Nitride Bubbles Using UV Laser Illumination.

Hexagonal boron nitride (h-BN) bubbles are of significant interest to micro-scale hydrogen storage thanks to their ability to confine hydrogen gas molecules. Previous reports of h-BN bubble creation from grown h-BN films require electron beams under vacuum, making integrating with other experimental setups for hydrogen production impractical. Therefore, in this study, the formation of h-BN bubbles is demonstrated in a 20 nm h-BN film grown on a sapphire substrate with a 213 nm UV laser beam. Using atomic force microscopy, it is shown that longer illumination time induces larger h-BN bubbles up to 20 µm with higher density. It is also demonstrated that h-BN bubbles do not collapse for more than 6 months after their creation. The internal pressure and gravimetric storage capacity of h-BN bubbles are reported. A maximum internal pressure of 41 MPa and a gravimetric storage capacity of 6% are obtained. These findings show that h-BN bubbles can be a promising system for long-term hydrogen storage.

A Retrofittable Photoelectron Gun for Low-Voltage Imaging Applications in the Scanning Electron Microscope.

Low-voltage scanning electron microscopy is a powerful tool for examining surface features and imaging beam-sensitive materials. Improving resolution during low-voltage imaging is then an important area of development. Decreasing the effect of chromatic aberration is one solution to improving the resolution and can be achieved by reducing the energy spread of the electron source. Our approach involves retrofitting a light source onto a thermionic lanthanum hexaboride (LaB6) electron gun as a cost-effective low energy-spread photoelectron emitter. The energy spread of the emitter's photoelectrons is theorized to be between 0.11 and 0.38 eV, depending on the photon energy of the ultraviolet (UV) light source. Proof-of-principle images have been recorded using this retrofitted photoelectron gun, and an analysis of its performance is presented.

The Effect of Combined Atmospheric Plasma/UV Treatments on Improving the Durability of Flame Retardants Applied to Cotton.

Application of a combined atmospheric plasma/UV laser to cotton fabrics impregnated with selected non-durable flame retardants (FRs) has shown evidence of covalent grafting of the latter species on to cotton fibre surfaces. As a result, an increase in their durability to water-soaking for 30 min at 40 °C has been recorded. Based on previous research plasma gases comprising Ar80%/CO220% or N280%/O220% were used to pre-expose cotton fabric prior to or after FR impregnation to promote the formation of radical species and increased −COOH groups on surface cellulosic chains, which would encourage formation of FR-cellulose bonds. Analysis by scanning electron microscopy (SEM/EDX), X-ray photoelectron spectroscopy (XPS) and thermal analysis (TGA) suggested that organophosphorus- and nitrogen- containing flame retarding species in the presence of the silicon-containing molecules such as 3-aminopropyltriethoxy silane (APTS) resulted in formation of FR-S-O-cellulose links, which gave rise to post-water-soaking FR retentions > 10%. Similarly, the organophosphorus FR, diethyl N, N bis (2-hydroxyethyl) aminomethylphosphonate (DBAP), after plasma/UV exposure produced similar percentage retention values possibly via (PO).O.cellulose bond formation, While none of the plasmas/UV-treated, FR-impregnated fabrics showed self-extinction behaviour, although burning rates reduced and significant char formation was evident, it has been shown that FR durability may be increased using plasma/UV treatments.

Assessing the local temperature of human cornea exposed to surface ablation by different laser refractive-surgery devices: a numerical comparative study.

To evaluate the local temperature at corneal tissue after applying single laser pulse from six commercial devices; Medilex™, Katana laser-soft, MEL90, Technolas-Teneo317, Alcon EX500, and PulzarTMZ1. The temperature distribution is simulated using finite element solution of the Penne's bio-heat transfer equation on a 3-D model of human cornea using the manufacturer's assigning parameters. The obtained results showed that the heating effect of Katana laser soft is 40% lower than MEL90 and Pulzar™ Z1, while the broad beam Medilex™ showed the minimum temperature rise especially at 248-nm laser radiation. The change in laser parameters selected for ablation has significant effect on the corneal local temperature. The broad beam-based device produces lower local corneal temperature than other flying spot types.

Flexible and Epitaxial Metal Oxide Thin Film Growth by Photoreaction Processing for Electrical and Optical Applications.

This review summarizes the use of photoreactions that replace conventional heating processes for growing oxide thin films from chemical solutions. In particular, this review outlines key variables in photoreactions that affect epitaxial and polycrystalline thin film growth, including precursor materials, laser wavelength, laser fluence, and carbon. In addition, the features of the photoreaction process that can be controlled at a low temperature by oxygen non-stoichiometry are examined. Likewise, functions that are neither achieved by developing a gradient structure nor controlled by a thermal equilibrium reaction are detailed. Two new concepts are presented, known as photoreaction of nanoparticles (PRNP) and photoreaction of a hybrid solutions (PRHS), in which crystal nuclei are pre-dispersed in a metal-organic compound film. This method has successfully produced flexible phosphor films used as resistor or thermistor electronic components. Finally, thin film growth using different light sources such as flash lamps and femtosecond lasers (fs) is explored.

Identification of novel direct protein-protein interactions by irradiating living cells with femtosecond UV laser pulses.

The identification of protein-protein interaction networks in living cells is becoming increasingly fundamental to elucidate main biological processes and to understand disease molecular bases on a system-wide level. We recently described a method (LUCK, Laser UV Cross-linKing) to cross-link interacting protein surfaces in living cells by UV laser irradiation. By using this innovative methodology, that does not require any protein modification or cell engineering, here we demonstrate that, upon UV laser irradiation of HeLa cells, a direct interaction between GAPDH and alpha-enolase was "frozen" by a cross-linking event. We validated the occurrence of this direct interaction by co-immunoprecipitation and Immuno-FRET analyses. This represents a proof of principle of the LUCK capability to reveal direct protein interactions in their physiological environment.

Femtosecond UV-laser pulses to unveil protein-protein interactions in living cells.

A hallmark to decipher bioprocesses is to characterize protein-protein interactions in living cells. To do this, the development of innovative methodologies, which do not alter proteins and their natural environment, is particularly needed. Here, we report a method (LUCK, Laser UV Cross-linKing) to in vivo cross-link proteins by UV-laser irradiation of living cells. Upon irradiation of HeLa cells under controlled conditions, cross-linked products of glyceraldehyde-3-phosphate dehydrogenase (GAPDH) were detected, whose yield was found to be a linear function of the total irradiation energy. We demonstrated that stable dimers of GAPDH were formed through intersubunit cross-linking, as also observed when the pure protein was irradiated by UV-laser in vitro. We proposed a defined patch of aromatic residues located at the enzyme subunit interface as the cross-linking sites involved in dimer formation. Hence, by this technique, UV-laser is able to photofix protein surfaces that come in direct contact. Due to the ultra-short time scale of UV-laser-induced cross-linking, this technique could be extended to weld even transient protein interactions in their native context.

Influence of multi-wavelength laser irradiation of enamel and dentin surfaces at 0.355, 2.94, and 9.4 µm on surface morphology, permeability, and acid resistance.

OBJECTIVE: Ultraviolet (UV) and infrared (IR) lasers can be used to specifically target protein, water, and mineral, respectively, in dental hard tissues to produce varying changes in surface morphology, permeability, reflectivity, and acid resistance. The purpose of this study was to explore the influence of laser irradiation and topical fluoride application on the surface morphology, permeability, reflectivity, and acid resistance of enamel and dentin to shed light on the mechanism of interaction and develop more effective treatments. METHODS: Twelve bovine enamel surfaces and twelve bovine dentin surfaces were irradiated with various combinations of lasers operating at 0.355 (Freq.-tripled Nd:YAG (UV) laser), 2.94 (Er:YAG laser), and 9.4 µm (CO2 laser), and surfaces were exposed to an acidulated phosphate fluoride gel and an acid challenge. Changes in the surface morphology, acid resistance, and permeability were measured using digital microscopy, polarized light microscopy, near-IR reflectance, fluorescence, polarization sensitive-optical coherence tomography (PS-OCT), and surface dehydration rate measurements. RESULTS: Different laser treatments dramatically influenced the surface morphology and permeability of both enamel and dentin. CO2 laser irradiation melted tooth surfaces. Er:YAG and UV lasers, while not melting tooth surfaces, showed markedly different surface roughness. Er:YAG irradiation led to significantly rougher enamel and dentin surfaces and led to higher permeability. There were significant differences in acid resistance among the various treatment groups. CONCLUSION: Surface dehydration measurements showed significant changes in permeability after laser treatments, application of fluoride and after exposure to demineralization. CO2 laser irradiation was most effective in inhibiting demineralization on enamel while topical fluoride was most effective for dentin surfaces. Lasers Surg. Med. 49:913-927, 2017. © 2017 Wiley Periodicals, Inc.

UV-laser-based microscopic dissection of tree rings - a novel sampling tool for δ(13) C and δ(18) O studies.

UV-laser-based microscopic systems were utilized to dissect and sample organic tissue for stable isotope measurements from thin wood cross-sections. We tested UV-laser-based microscopic tissue dissection in practice for high-resolution isotopic analyses (δ(13) C/δ(18) O) on thin cross-sections from different tree species. The method allows serial isolation of tissue of any shape and from millimetre down to micrometre scales. On-screen pre-defined areas of interest were automatically dissected and collected for mass spectrometric analysis. Three examples of high-resolution isotopic analyses revealed that: in comparison to δ(13) C of xylem cells, woody ray parenchyma of deciduous trees have the same year-to-year variability, but reveal offsets that are opposite in sign depending on whether wholewood or cellulose is considered; high-resolution tree-ring δ(18) O profiles of Indonesian teak reflect monsoonal rainfall patterns and are sensitive to rainfall extremes caused by ENSO; and seasonal moisture signals in intra-tree-ring δ(18) O of white pine are weighted by nonlinear intra-annual growth dynamics. The applications demonstrate that the use of UV-laser-based microscopic dissection allows for sampling plant tissue at ultrahigh resolution and unprecedented precision. This new technique facilitates sampling for stable isotope analysis of anatomical plant traits like combined tree eco-physiological, wood anatomical and dendroclimatological studies.

Imprinting on empty hard gelatin capsule shells containing titanium dioxide by application of the UV laser printing technique.

The purpose of this study was to examine the application of ultraviolet (UV) laser irradiation to printing hard gelatin capsule shells containing titanium dioxide (TiO2) and to clarify how the color strength of the printing by the laser could be controlled by the power of the irradiated laser. Hard gelatin capsule shells containing 3.5% TiO2 were used in this study. The capsules were irradiated with pulsed UV laser at a wavelength of 355 nm. The color strength of the printed capsule was determined by a spectrophotometer as total color difference (dE). The capsules could be printed gray by the UV laser. The formation of many black particles which were agglomerates of oxygen-defected TiO2 was associated with the printing. In the relationship between laser peak power of a pulse and dE, there were two inflection points. The lower point was the minimal laser peak power to form the black particles and was constant regardless of the dosage forms, for example film-coated tablets, soft gelatin capsules and hard gelatin capsules. The upper point was the minimal laser peak power to form micro-bubbles in the shells and was variable with the formulation. From the lower point to the upper point, the capsules were printed gray and the dE of the printing increased linearly with the laser peak power. Hard gelatin capsule shells containing TiO2 could be printed gray using the UV laser printing technique. The color strength of the printing could be controlled by regulating the laser energy between the two inflection points.

Improved Design of Slope-Shaped Hole-Blocking Layer and Electron-Blocking Layer in AlGaN-Based Near-Ultraviolet Laser Diodes.

The injection and leakage of charge carriers have a significant impact on the optoelectronic performance of GaN-based lasers. In order to improve the limitation of the laser on charge carriers, a slope-shape hole-barrier layer (HBL) and electron-barrier layer (EBL) structure are proposed for near-UV (NUV) GaN-based lasers. We used Crosslight LASTIP for the simulation and theoretical analysis of the energy bands of HBL and EBL. Our simulations suggest that the energy bands of slope-shape HBL and EBL structures are modulated, which could effectively suppress carrier leakage, improve carrier injection efficiency, increase stimulated radiation recombination rate in quantum wells, reduce the threshold current, improve optical field distribution, and, ultimately, improve laser output power. Therefore, using slope-shape HBL and EBL structures can achieve the superior electrical and optical performance of lasers.

Osteocyte gene expression analysis in mouse bone: optimization of a laser-assisted microdissection protocol.

Among bone cells, osteocytes are the most abundant, but also the most challenging to study because they are located inside a dense mineralized matrix. Due to their involvement in bone homeostasis, diverse tools are needed to understand their roles in bone physiology and pathology. This work was aimed at establishing a laser-assisted microdissection protocol to isolate osteocytes and analyze their gene expressions. The goal was to overcome the limitations of the technique currently most used: RNA extraction from the whole bone. To perform laser microdissection and subsequent gene expression analysis, the five main steps of the protocol have been adapted for the bone tissue. After testing many parameters, we found that the best options were (1) take unfixed snap-frozen tissue, (2) cryosection with a supported tape system to improve the tissue morphology if necessary, (3) microdissect regions of interest, and (4) recover the bone pieces by catapulting, if feasible, or by gravity. Finally, RNA extraction (5) was the most efficient with a precipitation method and allowed quantifying the expression of well described osteocyte genes (Gja1/Cx43, Phex, Pdpn, Dmp1, Sost). This work describes two protocols optimized for femur and calvaria and gives an overview of the many optimization options that one could try when facing difficulties with laser microdissection.

Fabrication and validation of flexible neural electrodes based on polyimide tape and gold sheet.

This research was conducted to apply polyimide tape, which has the advantages of low price ans strong adhesive strength, to the neural electrode process. In addition, to maximize the low-cost characteristics, a fabrication process based on UV laser patterning rather than a photolithography process was introduced. The fabrication process started by attaching the gold sheet on the conductive double-sided tape without being torn or crushed. Then, the gold sheet and the double-sided tape were patterned together using UV laser. The patterned layer was transferred to the single-side polyimide tape. For insulation layer, electrode site opened single-sided polyimide tape was prepared. Polydimethylsiloxane was used as an adhesion layer, and alignment between electrode sites and opening sites was processed manually. The minimum line width achieved through the proposed fabrication process was approximately 100 µm, and the sheet resistance of the conductive layer was 0.635 Ω/sq. Measured cathodal charge storage capacity was 0.72 mC/cm2 and impedance at 1 kHz was 4.07 kΩ/cm2. Validation of fabricated electrode was confirmed by conducting 30 days accelerated soak test, flexibility test, adhesion test and ex vivo stimulation test. The novel flexible neural electrodes based on single-sided polyimide tape and UV laser patterned gold sheet was fabricated successfully. Conventional neural electrode fabrication processes based on polyimide substrate has a disadvantages such as long fabrication time, expensive costs, and probability of delamination between layers. However, the novel fabrication process which we introduced can overcome many shortcomings of existing processes, and offers great advantages such as simplicity of fabrication, inexpensiveness, flexibility and long-term reliability.

UV-LASER adjuvant-surfactant-facilitated delivery of mobile dsRNA to tomato plant vasculature and evidence of biological activity by gene knockdown in the potato psyllid.

BACKGROUND: Double-stranded RNA (dsRNA) biopesticides are of interest for the abatement of insect vectors of pathogenic bacteria such as 'Candidatus Liberibacter', which infects both its psyllid and plant hosts. Silencing of genes essential for psyllids, or for Liberibacter, is anticipated to lead to mortality or impeded bacterial multiplication. Foliar delivery is preferred for biopesticide application; however, the cuticle impedes dsRNA penetration into the vasculature. Here, conditions were established for wounding tomato leaves using ultraviolet light amplification by stimulated emissions of radiation (UV-LASER) to promote dsRNA penetration into leaves and vasculature. RESULTS: UV-LASER treatment with application of select adjuvants/surfactants resulted in vascular delivery of 100-, 300- and 600-bp dsRNAs that, in general, were correlated with size. The 100-bp dsRNA required no pretreatment, whereas 300- and 600-bp dsRNAs entered the vasculature after UV-LASER treatment only and UV-LASER adjuvant/surfactant treatment, respectively. Of six adjuvant/surfactants evaluated, plant-derived oil combined with an anionic organosilicon compound performed most optimally. Localization of dsRNAs in the tomato vasculature was documented using fluorometry and fluorescence confocal microscopy. The biological activity of in planta-delivered dsRNA (200-250 bp) was determined by feeding third-instar psyllids on tomato leaves post UV-LASER adjuvant/surfactant treatment, with or without psyllid cdc42- and gelsolin dsRNAs. Gene knockdown was quantified by quantitative, real-time polymerase chain reaction with reverse transcription (RT-qPCR) amplification. At 10 days post the ingestion-access period, knockdown of cdc42 and gelsolin expression was 61% and 56%, respectively, indicating that the dsRNAs delivered to the tomato vasculature were mobile and biologically active. CONCLUSION: Results indicated that UV-LASER adjuvant/surfactant treatments facilitated the delivery of mobile, biologically active dsRNA molecules to the plant vasculature. © 2023 The Authors. Pest Management Science published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

UV laser-processed microstructure for building biohybrid actuators with anisotropic movement.

Fabrication of a biohybrid actuator requires muscle cells anisotropically aligned in a line, curve, or combination of lines and curves (similar to the microstructure of living muscle tissue) to replicate lifelike movements, in addition to considering the arrangement of skeletal structure or muscular structure with anisotropic straight patterns. Here, we report a UV laser-processed microstructure for freely directing cellular alignment to engineer a biohybrid actuator composed of poly(styrene-block-butadiene-block-styrene triblock copolymer) (SBS) thin film with tailor-made microgrooves (MGs) and skeletal myotubes aligned along these MGs. Specifically, straight, circular, or curved MGs were transferred to SBS thin films from a UV laser-processed template, allowing for the successful alignment of myotubes along MGs. The biohybrid actuator, composed of anisotropically aligned myotubes on a curved microgrooved SBS thin film, was contracted by electrical stimulation. Contraction of biohybrid actuators with curved aligned myotubes permits twisted-like behavior, unlike straight microgrooved films. Therefore, the UV laser-ablation system is a unique maskless and rapid microfabrication technique that provides intriguing opportunities for omni-directional microgrooved structures to achieve the complex motion of living organisms.

Pulse-on-Demand Operation for Precise High-Speed UV Laser Microstructuring.

Laser microstructuring has been studied extensively in the last decades due to its versatile, contactless processing and outstanding precision and structure quality on a wide range of materials. A limitation of the approach has been identified in the utilization of high average laser powers, with scanner movement fundamentally limited by laws of inertia. In this work, we apply a nanosecond UV laser working in an intrinsic pulse-on-demand mode, ensuring maximal utilization of the fastest commercially available galvanometric scanners at scanning speeds from 0 to 20 m/s. The effects of high-frequency pulse-on-demand operation were analyzed in terms of processing speeds, ablation efficiency, resulting surface quality, repeatability, and precision of the approach. Additionally, laser pulse duration was varied in single-digit nanosecond pulse durations and applied to high throughput microstructuring. We studied the effects of scanning speed on pulse-on-demand operation, single- and multipass laser percussion drilling performance, surface structuring of sensitive materials, and ablation efficiency for pulse durations in the range of 1-4 ns. We confirmed the pulse-on-demand operation suitability for microstructuring for a range of frequencies from below 1 kHz to 1.0 MHz with 5 ns timing precision and identified the scanners as the limiting factor even at full utilization. The ablation efficiency was improved with longer pulse durations, but structure quality degraded.

Rapid Fabrication of High-Performance Flexible Pressure Sensors Using Laser Pyrolysis Direct Writing.

The fabrication of flexible pressure sensors with low cost, high scalability, and easy fabrication is an essential driving force in developing flexible electronics, especially for high-performance sensors that require precise surface microstructures. However, optimizing complex fabrication processes and expensive microfabrication methods remains a significant challenge. In this study, we introduce a laser pyrolysis direct writing technology that enables rapid and efficient fabrication of high-performance flexible pressure sensors with a micro-truncated pyramid array. The pressure sensor demonstrates exceptional sensitivities, with the values of 3132.0, 322.5, and 27.8 kPa-1 in the pressure ranges of 0-0.5, 0.5-3.5, and 3.5-10 kPa, respectively. Furthermore, the sensor exhibits rapid response times (loading: 22 ms, unloading: 18 ms) and exceptional reliability, enduring over 3000 pressure loading and unloading cycles. Moreover, the pressure sensor can be easily integrated into a sensor array for spatial pressure distribution detection. The laser pyrolysis direct writing technology introduced in this study presents a highly efficient and promising approach to designing and fabricating high-performance flexible pressure sensors utilizing micro-structured polymer substrates.

A crystal-processing machine using a deep-ultraviolet laser: application to long-wavelength native SAD experiments.

While native SAD phasing is a promising method for next-generation macromolecular crystallography, it requires the collection of high-quality diffraction data using long-wavelength X-rays. The crystal itself and the noncrystalline medium around the crystal can cause background noise during long-wavelength X-ray data collection, hampering native SAD phasing. Optimizing the crystal size and shape or removing noncrystalline sample portions have thus been considered to be effective means of improving the data quality. A crystal-processing machine that uses a deep-UV laser has been developed. The machine utilizes the pulsed UV laser soft ablation (PULSA) technique, which generates less heat than methods using infrared or visible lasers. Since protein crystals are sensitive to heat damage, PULSA is an appropriate method to process them. Integration of a high-speed Galvano scanner and a high-precision goniometer enables protein crystals to be shaped precisely and efficiently. Application of this crystal-processing machine to a long-wavelength X-ray diffraction experiment significantly improved the diffraction data quality and thereby increased the success rate in experimental phasing using anomalous diffraction from atoms.

Femtosecond UV Laser Ablation Characteristics of Polymers Used as the Matrix of Astronautic Composite Material.

Ultrafast laser processing has recently emerged as a new tool for processing fiber-reinforced polymer (FRP) composites. In the astronautic industry, the modified epoxy resin (named 4211) and the modified cyanate ester resin (known as BS-4) are two of the most widely used polymers for polymer-based composites. To study the removal mechanism and ablation process of different material components during the ultrafast laser processing of FRPs, we isolated the role of the two important polymers from their composites by studying their femtosecond UV laser (260 fs, 343 nm) ablation characteristics for controllable machining and understanding the related mechanisms. Intrinsic properties for the materials' transmission spectrum, the absorption coefficient and the optical bandgap (Eg), were measured, derived, and compared. Key parameters for controllable laser processing, including the ablation threshold (Fth), energy penetration depth (δeff), and absorbed energy density (Eabs) at the ablation threshold, as well as their respective "incubation" effect under multiple pulse excitations, were deduced analytically. The ablation thresholds for the two resins, derived from both the diameter-regression and depth-regression techniques, were compared between resins and between techniques. An optical bandgap of 3.1 eV and 2.8 eV for the 4211 and BS-4 resins, respectively, were obtained. A detectable but insignificant-to-ablation difference in intrinsic properties and ablation characteristics between the two resins was found. A systematic discrepancy, by a factor of 30~50%, between the two techniques for deriving ablation thresholds was shown and discussed. For the 4211 resin ablated by a single UV laser pulse, a Fth of 0.42 J/cm2, a δeff of 219 nm, and an Eabs of 18.4 kJ/cm3 was suggested, and they are 0.45 J/cm2, 183 nm, and 23.2 kJ/cm3, respectively, for the BS-4 resin. The study may shed light on the materials' UV laser processing, further the theoretical modeling of ultrafast laser ablation, and provide a reference for the femtosecond UV laser processing characteristics of FRPs for the future.

Integration of Impedimetric Sensors for In Situ Electrochemical Impedance Spectroscopy in Free-Flow Electrophoresis Applications in Lab-on-Chip Systems.

Miniaturization and integration of chemical reactions into fluidic systems in combination with product purification or buffer exchange can reduce the amount of solvents and reactants required while increasing synthesis efficiency. A critical step is the regulation of flow rates to realize optimal synthesis conditions and high purification rates, so real-time, label-free monitoring is required in methods such as free-flow electrophoresis. Optical detection methods are widely used, but they often have complex excitation and detection setups that are disadvantageous for point-of-care applications. The method we have chosen is electrochemical impedance spectroscopy for detecting charged compounds in aqueous buffers with low ionic strength. Propranolol was selected for proof of concept and was separated from the organic solvent and the precursor oxirane by free-flow electrophoresis. For this purpose, electrode structures were fabricated in microfluidic channels by photolithographic lift-off technique and optimized in terms of positioning, electrode size and distance for sensitive detection, and quantification of propranolol in the nanomolar range. It is also noteworthy that the organic solvent dimethyl sulfoxide (DMSO) could be detected and quantified by an increased impedance magnitude. Subsequently, the optimized interdigital electrode structures were integrated into the outlet channels of the electrophoretic separation chamber to monitor the various outgoing fluidic streams and provide in-line control of the fluidic flows for the purification step. In conclusion, we can provide a microfluidic chip to monitor the separation efficiency of a substance mixture during free-flow electrophoresis without the need of complex analytical techniques using electrochemical impedance spectroscopy.