Results of the cyclic triaxial testing on mechanically-biologically treated waste.

Accurate assessment of the dynamic strength characteristics of mechanically-biologically treated (MBT) waste is crucial for the construction and safe operation of landfill sites. Herein, samples of MBT waste from the Hangzhou Tianziling landfill were collected and subjected to consolidated undrained cyclic triaxial tests under four confinement levels and six cyclic stress ratios (CSRs). Under cyclic loading, the MBT waste exhibited a critical CSR. If the CSR exceeds the critical value, the MBT waste specimen rapidly undergoes deformation and failure. Dynamic strength of MBT waste decreases with an increase in the number of cyclic vibrations and increases with an increase in confining pressure. Considering the influence of cyclic vibrations and confining pressure, a formula for dynamic strength in terms of cyclic vibrations and confining pressure has been established. The dynamic shear strength parameter ranges for MBT waste were obtained under different seismic magnitudes. We compared the dynamic and static shear strength parameters of MBT waste and municipal solid waste. These study findings can serve as a reference for the dynamic stability analysis of MBT waste landfills.

Variation in perikymata counts between repetitive episodes of linear enamel hypoplasia among orangutans from Sumatra and Borneo.

The goal of this study is to evaluate whether repetitive linear enamel hypoplasia (rLEH) in apes is ecologically informative. LEH, which appears as grooves of thinner enamel often caused by malnutrition and/or disease, is a permanent record of departures from developmental homeostasis in infant and juvenile apes. Orangutans were selected for the study as they are a threatened species, have a remarkably high prevalence of rLEH, and because Sumatra is deemed a better habitat for orangutans than is Borneo, facilitating an ecological comparison. Objectives are to determine: a) whether periodicity of rLEH in orangutans corresponds to monsoon-mediated cycles in precipitation or food; and b) whether patterning of rLEH supports the view that Borneo is an inferior habitat. This study compares the counts of perikymata between adjacent LEH from 9 Sumatran and 26 Bornean orangutans to estimate the periodicity of rLEH. A total of 131 nonredundant inter-LEH perikymata counts were transformed to natural log values to reveal clusters of counts in a multiplicative series. Using a value of 10 days to form one perikyma, rLEH tends to recur semiannually in both populations. However, Sumatran orangutans show significantly fewer semiannual intervals and more annually recurring episodes. Bornean orangutans show mostly semiannual intervals and are more variable in inter-LEH perikymata counts. It is concluded that: a) developmental conditions for infant orangutans in Sumatra protect them somewhat from seasonal and environmental variation; b) temporal patterning of rLEH indicates that Borneo is the poorer habitat for orangutans; and c) the study of rLEH can be ecologically informative.

Microecology of aerobic denitrification system construction driven by cyclic stress of sulfamethoxazole.

The construction of aerobic denitrification (AD) systems in an antibiotic-stressed environment is a serious challenge. This study investigated strategy of cyclic stress with concentration gradient (5-30 mg/L) of sulfamethoxazole (SMX) in a sequencing batch reactor (SBR), to achieve operation of AD. Total nitrogen removal efficiency of system increased from about 10 % to 95 %. Original response of abundant-rare genera to antibiotics was changed by SMX stress, particularly conditionally rare or abundant taxa (CRAT). AD process depends on synergistic effect of heterotrophic nitrifying aerobic denitrification bacteria (Paracoccus, Thauera, Hypomicrobium, etc). AmoABC, napA, and nirK were functionally co-expressed with multiple antibiotic resistance genes (ARGs) (acrR, ereAB, and mdtO), facilitating AD process. ARGs and TCA cycling synergistically enhance the antioxidant and electron transport capacities of AD process. Antibiotic efflux pump mechanism played an important role in operation of AD. The study provides strong support for regulating activated sludge to achieve in situ AD function.

Estimation of Cyclic Stress-Strain Curves of Steels Based on Monotonic Properties Using Artificial Neural Networks.

This paper introduces a novel method for estimating the cyclic stress-strain curves of steels based on their monotonic properties and plastic strain amplitudes, utilizing artificial neural networks (ANNs). ANNs were trained on a substantial number of experimental data for steels, collected from relevant literature, and divided into subgroups according to alloying elements content (unalloyed, low-alloy, and high-alloy steels). Only monotonic properties that were proven to be relevant for the estimation of points on the stress-strain curve were used. The performance of the developed ANNs was assessed using an independent set of data, and the results were compared to experimental values, values obtained by existing empirical estimation methods, and by previously developed ANNs. The results showed that the new approach which combines relevant monotonic properties and plastic strain amplitudes as inputs to ANNs for cyclic stress-strain curve estimation is better than the previously used approach where ANNs estimate the parameters of the Ramberg-Osgood material model separately. This shows that a more favorable approach to the estimation of cyclic stress-strain behavior would be to directly estimate corresponding material curves using monotonic properties. Additionally, this may also reduce inaccuracies resulting from simplified representations of the actual material behavior inherent in the material model.

A Hyper-Pseudoelastic Model of Cyclic Stress-Softening Effect for Rubber Composites.

Rubber composites are hyperelastic materials with obvious stress-softening effects during the cyclic loading-unloading process. In previous studies, it is hard to obtain the stress responses of rubber composites at arbitrary loading-unloading orders directly. In this paper, a hyper-pseudoelastic model is developed to characterize the cyclic stress-softening effect of rubber composites with a fixed stretch amplitude at arbitrary loading-unloading order. The theoretical relationship between strain energy function and cyclic loading-unloading order is correlated by the hyper-pseudoelastic model directly. Initially, the basic laws of the cyclic stress-softening effect of rubber composites are revealed based on the cyclic loading-unloading experiments. Then, a theoretical relationship between the strain energy evolution function and loading-unloading order, as well as the pseudoelastic theory, is developed. Additionally, the basic constraints that the strain energy evolution function must satisfy in the presence or absence of residual deformation effect are derived. Finally, the calibration process of material parameters in the hyper-pseudoelastic model is also presented. The validity of the hyper-pseudoelastic model is demonstrated via the comparisons to experimental data of rubber composites with different filler contents. This paper presents a theoretical model for characterizing the stress-softening effect of rubber composites during the cyclic loading-unloading process. The proposed theoretical model can accurately predict the evolution of the mechanical behavior of rubber composites with the number of loading-unloading cycles, which provides scientific guidance for predicting the durability properties and analyzing the fatigue performance of rubber composites.

Degradation behavior of 2D auxetic structure with biodegradable polymer under mechanical stress.

Coronary heart disease is serious harm to human health. Vascular scaffold implantation is the main treatment. Biodegradable polymers are widely used in vascular scaffolds for good biodegradability and biocompatibility. However, whether the mechanical properties and radial expansion ability can successfully implant the scaffold without acute elastic retraction remains to be further studied. Because of the unique deformation mechanism, shear resistance, and resilience, auxetic structures can effectively avoid the restenosis of degraded vascular scaffolds. Firstly, the plane isotropic and plane anisotropic auxetic structural scaffolds were designed. The control structures (traditional structures) scaffolds were taken as the contrast. PCL was used to prepare the vascular auxetic by 3D printing. The printing parameters of fused deposition 3D printing, such as printing temperature, printing speed, and printing pressure, were studied to determine the optimal printing parameters of PCL. A self-assembled cyclic tensile stress loading device was used to investigate the degradation behavior of different scaffolds under different sizes of cyclic tensile stress, such as surface morphology, pH changes, mass loss rate, and mechanical properties. The increase of stress, surface roughness, and mass loss rate of the scaffolds all showed an increasing trend. pH gradually decreased from the fifth week, and the decrease was proportional to the stress. A large level of stress loading intensifies the decline of elastic modulus and the ultimate strength of the scaffold. In conclusion, the increase of periodic tensile stress will accelerate the degradation of scaffolds, and the degradation behavior of scaffolds with different configurations is different. The degradation rate of dilatant scaffolds was higher than that of control scaffolds, and the degradation rate of anisotropic auxetic scaffolds was higher than that of isotropic auxetic scaffolds, which provides a theoretical reference for the application of auxetic structure in the degradation of vascular scaffolds.

Investigation of Changes in Fatigue Damage Caused by Mean Load under Block Loading Conditions.

The literature in the area of material fatigue indicates that the fatigue properties may change with the number of cycles. Researchers recommend taking this into account in fatigue life calculation algorithms. The results of simulation research presented in this paper relate to an algorithm for estimating the fatigue life of specimens subjected to block loading with a nonzero mean value. The problem of block loads using a novel calculation model is presented in this paper. The model takes into account the change in stress-strain curve parameters caused by mean strain. Simulation tests were performed for generated triangular waveforms of strains, where load blocks with changed mean strain values were applied. During the analysis, the degree of fatigue damage was compared. The results of calculations obtained for standard values of stress-strain parameters (for symmetric loads) and those determined, taking into account changes in the curve parameters, are compared and presented in this paper. It is shown that by neglecting the effect of the mean strain value on the K' and n' parameters and by considering only the parameters of the cyclic deformation curve for εm = 0 (symmetric loads), the ratio of the total degree of fatigue damage varies from 10% for εa = 0.2% to 3.5% for εa = 0.6%. The largest differences in the calculation for ratios of the partial degrees of fatigue damage were observed in relation to the reference case for the sequence of block n3, where εm = 0.4%. The simulation results show that higher mean strains change the properties of the material, and in such cases, it is necessary to take into account the influence of the mean value on the material response under block loads.

Monotonic and Fatigue Behavior of EBM Manufactured Ti-6Al-4V Solid Samples: Experimental, Analytical and Numerical Investigations.

The present study aims to carry out an experimental, analytical and numerical investigation of the monotonic and fatigue performance of electron beam melted Ti-6Al-4V structures. Therefore, tensile tests, multiple step tests and strain-life tests were performed on machined EBM Ti-6Al-4V solid samples. An elastic-plastic material model in combination with a numerical damage model was examined according to the experimental tensile tests. Analytical models proposed by Ramberg and Osgood, as well as Coffin and Manson were obtained to describe the cyclic stress-strain curves and strain-life curves, respectively. The fracture surfaces of the tested samples and the influence of different build directions were analyzed. A prediction of the static and fatigue material properties is of particular importance, e.g., for the safe application of additively manufactured load-bearing implant structures. Based on the determined analytical and numerical models, the material and product behavior of complex electron beam melted structures under cyclic loading and fatigue life determination can be investigated in the early stages of the product development process.

Prediction of Cyclic Stress-Strain Property of Steels by Crystal Plasticity Simulations and Machine Learning.

In this study, a method for the prediction of cyclic stress-strain properties of ferrite-pearlite steels was proposed. At first, synthetic microstructures were generated based on an anisotropic tessellation from the results of electron backscatter diffraction (EBSD) analyses. Low-cycle fatigue experiments under strain-controlled conditions were conducted in order to calibrate material property parameters for both an anisotropic crystal plasticity and an isotropic J2 model. Numerical finite element simulations were conducted using these synthetic microstructures and material properties based on experimental results, and cyclic stress-strain properties were calculated. Then, two-point correlations of synthetic microstructures were calculated to quantify the microstructures. The microstructure-property dataset was obtained by associating a two-point correlation and calculated cyclic stress-strain property. Machine learning, such as a linear regression model and neural network, was conducted using the dataset. Finally, cyclic stress-strain properties were predicted from the result of EBSD analysis using the obtained machine learning model and were compared with the results of the low-cycle fatigue experiments.

Low Cycle Fatigue Behavior of Steam Generator Tubes under Axial Loading.

Compared with the fatigue properties of the material (Inconel Alloy 690), the real fatigue lives of tubes are more meaningful in the fatigue design and assessment of steam generator (SG) tube bundles. However, it is almost impossible to get a satisfactory result by conducting fatigue tests on the tube directly. A tube with a uniform and thin wall easily fails near the clamping ends under cyclic loading due to the stress concentration. In this research, a set-up for fatigue tests of real tubes is proposed to overcome the stress concentration. With the set-up, low cycle fatigue tests were conducted in accordance with an existing fatigue design curve for Alloy 690. Strain control mode was applied with fully reversed push⁻pull loading under different strain amplitudes (0.15%, 0.2%, 0.3%, and 0.4%). A favourable result was obtained, and the low cycle fatigue behavior was investigated. The results showed that the fatigue life tested by the real tube was below the strain⁻life curve of Alloy 690 which was fitted by conventional solid specimens. A cyclic hardening behavior was found by the cyclic stress⁻strain curve when compared with the monotonic stress⁻strain curve.

Data demonstrating the effects of build orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel.

Axial fully-reversed strain-controlled ([Formula: see text]) fatigue experiments were performed to obtain data demonstrating the effects of building orientation (i.e. vertical versus horizontal) and heat treatment on the fatigue behavior of 17-4 PH stainless steel (SS) fabricated via Selective Laser Melting (SLM) (Yadollahi et al., submitted for publication [1]). This data article provides detailed experimental data including cyclic stress-strain responses, variations of peak stresses during cyclic deformation, and fractography of post-mortem specimens for SLM 17-4 PH SS.