Development of hybrid polyvinylpyrrolidone/carboxymethyl cellulose/collagen incorporated oregano scaffolds via direct ink write printing for potential wound healing applications.

Additive manufacturing can develop regenerative scaffolds for wound healing. 3D printing offers meticulous porosity, mechanical integrity, cell adhesion and cost-effectiveness. Herein, we prepared ink composed of carboxymethyl cellulose (CMC), polyvinylpyrrolidone (PVP), collagen, and oregano extract for the fabrication of tissue constructs. The blend was optimized to form a homogeneous ink and rheological characterization demonstrated shear thinning behavior. The scaffolds were printed using Direct Ink Write (DIW) at a flow speed of 4 mm3/s and a layer height of 0.18 mm. The fabricated scaffolds demonstrated an ultimate tensile strength (UTS) and toughness of 730 KPa and 2.72 MJ/m3, respectively. Scanning Electron Microscopy (SEM) revealed an average pore size of 300 ± 30 µm. Fourier transform infrared spectroscopy (FTIR) analysis confirmed that all materials were present. The contact angle of the composite scaffold was 68° ± 1°. Moreover, the scaffolds presented 82 % mass loss (degradation) in phosphate buffer saline (PBS) over 14 days. The composite scaffold exhibited inhibition zones of 9 mm and 12 mm against Staphylococcus aureus and Escherichia coli, respectively. The PVP/CMC/collagen/oregano 3D printed scaffolds exhibited excellent biocompatibility with the mesenchymal stem cells and humman dermal fibroblast cells, confirmed by water-soluble tetrazolium - 8 (WST-8) assay (test conducted for 7 days). The enhanced angiogenic potential of said scaffold was assesed by release of vascular endothelial growth factor followed by further validation through in-vivo CAM assay. Thus, confirming suitability for the potential wound healing application.

Dual feed progressive cavity pump extrusion system for functionally graded direct ink write 3D printing.

Material extrusion Additive Manufacturing (AM), is one of the most widely practiced methods of AM. Fused Filament Fabrication (FFF) is what most associate with AM, as it is relatively inexpensive, and highly accessible, involving feeding plastic filament into a hot-end that melts and extrudes from a nozzle as the toolhead moves along the toolpath. Direct Ink Write (DIW) 3D printing falls into this same category of AM, however is primarily practiced in laboratory settings to construct novel parts from flowable feedstock materials. DIW printers are relatively expensive and often depend on custom software to print a part, limiting user-specificity. There have been recent advancements in multi-material and functionally graded DIW, but the systems are highly custom and the methods used to achieve multi-material prints are openly available to the public. The following article outlines the construction and operation method of a DIW system that is capable of printing that can produce compositionally-graded components using a dual feed progressive cavity pump extruder equipped with a dynamic mixer. The extruder and its capabilities to vary material composition while printing are demonstrated using a Prusa i3 MK3S+ desktop fused filament fabrication printer as the gantry system. This provides users ease of operation, and the capability of further tailoring to specific needs.

Bionic Artificial Skin Based on Self-Healable Ionogel Composites with Tailored Mechanics and Robust Interfaces.

Bionic artificial skin which imitates the features and functions of human skin, has broad applications in wearable human-machine interfaces. However, equipping artificial materials with skin-like mechanical properties, self-healing ability, and high sensitivity remains challenging. Here, inspired by the structure of human skin, an artificial skin based on ionogel composites with tailored mechanical properties and robust interface is prepared. Combining finite element analysis and direct ink writing (DIW) 3D printing technology, an ionogel composite with a rigid skeleton and an ionogel matrix is precisely designed and fabricated, realizing the mechanical anisotropy and nonlinear mechanical response that accurately mimic human skin. Robust interface is created through co-curing of the skeleton and matrix resins, significantly enhancing the stability of the composite. The realization of self-healing ability and resistance to crack growth further ensure the remarkable durability of the artificial skin for sensing application. In summary, the bionic artificial skin mimics the characteristics of human skin, including mechanical anisotropy, nonlinear mechanical response, self-healing capability, durability and high sensitivity when applied as flexible sensors. These strategies provide strong support for the fabrication of tissue-like materials with adaptive mechanical behaviors.

3D-printed polyether-ether ketone/carboxymethyl cellulose scaffolds coated with Zn-Mn doped mesoporous bioactive glass nanoparticles.

Patient-specific fabrication of scaffold/implant requires an engineering approach to manufacture the ideal scaffold. Herein, we design and 3D print scaffolds comprised of polyether-ether-ketone (PEEK) and sodium-carboxymethyl cellulose (Na-CMC). The fabricated scaffold was dip coated with Zn and Mn doped bioactive glass nanoparticles (Zn-Mn MBGNs). The synthesized ink exhibit suitable shear-thinning behavior for direct ink write (DIW) 3D printing. The scaffolds were crafted with precision, featuring 85% porosity, 0.3 mm layer height, and 1.5 mm/s printing speed at room temperature. Scanning electron microscopy images reveal a well-defined scaffold with an average pore size of 600 ± 30 µm. The energy dispersive X-ray spectroscopy analysis confirmed a well dispersed/uniform coating of Zn-Mn MBGNs on the PEEK/Na-CMC scaffold. Fourier transform infrared spectroscopy approved the presence of PEEK, CMC, and Zn-Mn MBGNs. The tensile test revealed a Young's modulus of 2.05 GPa. Antibacterial assays demonstrate inhibition zone against Staphylococcus aureus and Escherichia Coli strains. Chick Chorioallantoic Membrane assays also present significant angiogenesis potential, owing to the antigenic nature of Zn-Mn MBGNs. WST-8 cell viability assays depicted cell proliferation, with a 103% viability after 7 days of culture. This study suggests that the PEEK/Na-CMC scaffolds coated with Zn-Mn MBGNs are an excellent candidate for osteoporotic fracture treatment. Thus, the fabricated scaffold can offer multifaceted properties for enhanced patient outcomes in the bone tissue regeneration.

Novel and Accessible Physical Recycling for Expanded Polystyrene Waste with the Use of Acetone as a Solvent and Additive Manufacturing (Direct Ink-Write 3D Printing).

The current high production of plastics has prompted the exploration of alternative pathways to facilitate recycling, aiming for a progressively sustainable society. This paper presents an alternative and affordable technology for treating waste expanded polystyrene (EPS) mixed with acetone in a 100:1 volume ratio to be used as 3D printing ink for Direct Ink Write technology. In order to optimize the printing parameters, a comprehensive study was conducted, evaluating different needle diameters, printing speeds, and bed temperature values to achieve homogenous pieces and a highly repeatable 3D printing process. Results showed that the main optimum printing parameters were using needles with diameters of 14 to 16 G and printing speeds ranging from 2 to 12 mm/s, which were found to yield the most uniform ribbons. Increasing the bed temperature, despite favoring acetone evaporation, led to the generation of more heterogeneous structures due to void growth inside the printed ribbons. Thus, employing room temperature for the bed proved to be the optimal value. Lastly, a comparative study between the starting material and the EPS after the printing process was conducted using FTIR-ATR and GPC analyses, ensuring the preservation of the original polymer's integrity during physical recycling.

3D Printing of Ionogels with Complementary Functionalities Enabled by Self-Regulating Ink.

Shaping soft and conductive materials into sophisticated architectures through 3D printing is driving innovation in myriad applications, such as robotic counterparts that emulate the synergic functions of biological systems. Although recently developed multi-material 3D printing has enabled on-demand creation of intricate artificial counterparts from a wide range of functional viscoelastic materials. However, directly achieving complementary functionalities in one ink design remains largely unexplored, given the issues of printability and synergy among ink components. In this study, an easily accessible and self-regulating tricomponent ionogel-based ink design to address these challenges is reported. The resultant 3D printed objects, based on the same component but with varying ratios of ink formulations, exhibit distinct yet complementary properties. For example, their Young's modulus can differ by three orders of magnitude, and some structures are rigid while others are ductile and viscous. A theoretical model is also employed for predicting and controlling the printing resolution. By integrating complementary functionalities, one further demonstrates a representative bioinspired prototype of spiderweb, which mimics the sophisticated structure and multiple functions of a natural spiderweb, even working and camouflaging underwater. This ink design strategy greatly extends the material choice and can provide valuable guidance in constructing diverse artificial systems by 3D printing.

Triplet Fusion Upconversion for Photocuring 3D-Printed Particle-Reinforced Composite Networks.

High energy photons (λ < 400 nm) are frequently used to initiate free radical polymerizations to form polymer networks, but are only effective for transparent objects. This phenomenon poses a major challenge to additive manufacturing of particle-reinforced composite networks since deep light penetration of short-wavelength photons limits the homogeneous modification of physicochemical and mechanical properties. Herein, the unconventional, yet versatile, multiexciton process of triplet-triplet annihilation upconversion (TTA-UC) is employed for curing opaque hydrogel composites created by direct-ink-write (DIW) 3D printing. TTA-UC converts low energy red light (λmax  = 660 nm) for deep penetration into higher-energy blue light to initiate free radical polymerizations within opaque objects. As proof-of-principle, hydrogels containing up to 15 wt.% TiO2 filler particles and doped with TTA-UC chromophores are readily cured with red light, while composites without the chromophores and TiO2 loadings as little as 1-2 wt.% remain uncured. Importantly, this method has wide potential to modify the chemical and mechanical properties of complex DIW 3D-printed composite polymer networks.

Direct-Ink-Write Printing and Electrospinning of Cellulose Derivatives for Conductive Composite Materials.

The aim of this study is to realize the controlled construction and modulation of micro-/nanostructures of conductive composite materials (CCMs) in a facile way. Herein, interdigital electrodes are prepared by direct-ink-write printing co-blended inks made of ethyl cellulose and carbon nanotubes on cellulose paper. The cellulose nanofibers (CFs) are prepared by electrospinning cellulose acetate on to an aluminum foil, followed by deacetylation in NaOH/ethanol. All co-blended inks exhibit a typical non-Newtonian shear thinning behavior, enabling smooth extrusion and printing. The above electrodes and the conductive CF films with excellent thermal stability are assembled into a pressure sensor, which has a high sensitivity (0.0584 KPa-1) to detect the change in external loading pressure. The obtained porous CFs film is further endowed with conductivity by in situ polymerization of polypyrrole (PPy), which are uniformly distributed on the CFs surface as particles; a triboelectric nanogenerator is constructed by using the CF@PPy film as a tribo-positive friction layer to achieve efficient energy harvesting (output voltage = 29.78 V, output current = 2.12 µA). Therefore, the construction of CCMs with micro-/nanostructures based on cellulose derivatives have essential application prospects in emerging high-tech fields, such as green electronics for sensing and energy harvesting.

3D Printing of Ridged FeS2 Cathodes for Improved Rate Capability and Custom-Form Lithium Batteries.

Additive manufacturing can enable the fabrication of batteries in nonconventional form factors, enabling higher practical energy density due to improved material packing efficiency of power sources in devices. Furthermore, energy density can be improved by transitioning from conventional Li-ion battery materials to lithium metal anodes and conversion cathodes. Iron disulfide (FeS2) is a prominent conversion cathode of commercial interest; however, the direct-ink-write (DIW) printing of FeS2 inks for custom-form battery applications has yet to be demonstrated or optimized. In this work, DIW printing of FeS2 inks is used to systematically investigate the impact of ink solid concentration on rheology, film shape retention on arbitrary surfaces, cathode morphology, and electrochemical cell performance. We find that cathodes with a ridged interface, produced from the filamentary extrusion of highly concentrated FeS2 inks (60-70% solids w/w%), exhibit optimal power, uniformity, and stability when cycled at higher rates (in excess of C/10). Meanwhile, cells with custom-form, wave-shaped electrodes (printed FeS2 cathodes and pressed lithium anodes) are demonstrated and shown to exhibit similar performance to comparable cells in planar configurations, demonstrating the feasibility of printing onto complex geometries. Overall, the DIW printing of FeS2 inks is shown to be a viable path toward the making of custom-form conversion lithium batteries. More broadly, ridging is found to optimize rate capability, a finding that may have a broad impact beyond FeS2 and syringe extrusion.

3D Printing of Liquid Metal Embedded Elastomers for Soft Thermal and Electrical Materials.

Liquid metal embedded elastomers (LMEEs) are composed of a soft polymer matrix embedded with droplets of metal alloys that are liquid at room temperature. These soft matter composites exhibit exceptional combinations of elastic, electrical, and thermal properties that make them uniquely suited for applications in flexible electronics, soft robotics, and thermal management. However, the fabrication of LMEE structures has primarily relied on rudimentary techniques that limit patterning to simple planar geometries. Here, we introduce an approach for direct ink write (DIW) printing of a printable LMEE ink to create three-dimensional shapes with various designs. We use eutectic gallium-indium (EGaIn) as the liquid metal, which reacts with oxygen to form an electrically insulating oxide skin that acts as a surfactant and stabilizes the droplets for 3D printing. To rupture the oxide skin and achieve electrical conductivity, we encase the LMEE in a viscoelastic polymer and apply acoustic shock. For printed composites with a 80% LM volume fraction, this activation method allows for a volumetric electrical conductivity of 5 × 104 S cm-1 (80% LM volume)─significantly higher than what had been previously reported with mechanically sintered EGaIn-silicone composites. Moreover, we demonstrate the ability to print 3D LMEE interfaces that provide enhanced charge transfer for a triboelectric nanogenerator (TENG) and improved thermal conductivity within a thermoelectric device (TED). The 3D printed LMEE can be integrated with a highly soft TED that is wearable and capable of providing cooling/heating to the skin through electrical stimulation.

Direct Ink Write Printing of Chitin-Based Gel Fibers with Customizable Fibril Alignment, Porosity, and Mechanical Properties for Biomedical Applications.

A fine control over different dimensional scales is a challenging target for material science since it could grant control over many properties of the final material. In this study, we developed a multivariable additive manufacturing process, direct ink write printing, to control different architectural features from the nano- to the millimeter scale during extrusion. Chitin-based gel fibers with a water content of around 1500% were obtained extruding a polymeric solution of chitin into a counter solvent, water, inducing instant solidification of the material. A certain degree of fibrillar alignment was achieved basing on the shear stress induced by the nozzle. In this study we took into account a single variable, the nozzle's internal diameter (NID). In fact, a positive correlation between NID, fibril alignment, and mechanical resistance was observed. A negative correlation with NID was observed with porosity, exposed surface, and lightly with water content. No correlation was observed with maximum elongation (~50%), and the scaffold's excellent biocompatibility, which appeared unaltered. Overall, a single variable allowed a customization of different material features, which could be further tuned, adding control over other aspects of the synthetic process. Moreover, this manufacturing could be potentially applied to any polymer.

Additive-Manufactured Stochastic Polyimide Foams for Low Relative Permittivity, Lightweight Electronic Architectures.

Polyimides are widely utilized engineering polymers due to their excellent balance of mechanical, dielectric, and thermal properties. However, the manufacturing of polyimides into complex multifunctional designs can be hindered by dimensional shrinkage of the polymer upon imidization and post processing methods and inability to tailor electronic or mechanical properties. In this work, we developed methods to three-dimensional (3D) direct ink write polyimide closed-cell stochastic foams with tunable densities. These polyimide structures preserve the geometrical fidelity of 3D design with a linear shrinkage value of <10% and displayed microscale porosity ranging from 25 to 35%. This unique balance of morphology and direct-write compatibility was enabled by polymer phase inversion behavior without the need of conventional post-print cross-linking, imidization, or pore-inducing freeze processing. The manufacturability, thermal stability, and dielectric properties of the 3D polyimide stochastic foams reported here serve as enablers for the exploration of hierarchical, lightweight, high-temperature, high-power electronics.

4D-Printable Liquid Metal-Liquid Crystal Elastomer Composites.

Soft actuators that undergo programmable shape change in response to a stimulus are enabling components of future soft robots and other soft machines. Strategies to power these actuators often require the incorporation of rigid, electrically conductive materials into the soft actuator, thus limiting the compliance and shape change of the material. In this study, we develop a 4D-printable composite composed of liquid crystal elastomer (LCE) matrix with dispersed droplets of eutectic gallium indium alloy (EGaIn). Using deformable EGaIn droplets in place of rigid conductive fillers preserves the compliance and shape-morphing properties of the LCE. The process enables 4D-printed LCE actuators capable of photothermal and electrothermal actuation. At low liquid metal (LM) concentrations (71 wt %), the composite actuator exhibits a photothermal response upon irradiation of near-IR light. Printed actuators with a twisted nematic configuration are capable of bending angles of 150° at 800 mW cm-2. At higher LM concentrations (88 wt %), the embedded LM droplets can form percolating networks that conduct electricity and enable electrical Joule heating of the LCE. Actuation strain ranging from 5 to 12% is controlled by the amount of electrical power that is delivered to the composite. We also introduce a method for multimaterial printing of monolithic structures where the LM filler loading is spatially varied. These multifunctional materials exhibit innate responsivity where the actuator behaves as an electrical switch and can report one of two states (on/off). These multiresponsive, 4D-printable composites enable multifunctional, mechanically active structures that can be powered with IR light or low DC voltages.

3D printing of glass by additive manufacturing techniques: a review.

Additive manufacturing (AM), which is also known as three-dimensional (3D) printing, uses computer-aided design to build objects layer by layer. Here, we focus on the recent progress in the development of techniques for 3D printing of glass, an important optoelectronic material, including fused deposition modeling, selective laser sintering/melting, stereolithography (SLA) and direct ink writing. We compare these 3D printing methods and analyze their benefits and problems for the manufacturing of functional glass objects. In addition, we discuss the technological principles of 3D glass printing and applications of 3D printed glass objects. This review is finalized by a summary of the current achievements and perspectives for the future development of the 3D glass printing technique.

Continuous Based Direct Ink Write for Tubular Cardiovascular Medical Devices.

Bioresorbable cardiovascular applications are increasing in demand as fixed medical devices cause episodes of late restenosis. The autologous treatment is, so far, the gold standard for vascular grafts due to the similarities to the replaced tissue. Thus, the possibility of customizing each application to its end user is ideal for treating pathologies within a dynamic system that receives constant stimuli, such as the cardiovascular system. Direct Ink Writing (DIW) is increasingly utilized for biomedical purposes because it can create composite bioinks by combining polymers and materials from other domains to create DIW-printable materials that provide characteristics of interest, such as anticoagulation, mechanical resistance, or radiopacity. In addition, bioinks can be tailored to encounter the optimal rheological properties for the DIW purpose. This review delves into a novel emerging field of cardiovascular medical applications, where this technology is applied in the tubular 3D printing approach. Cardiovascular stents and vascular grafts manufactured with this new technology are reviewed. The advantages and limitations of blending inks with cells, composite materials, or drugs are highlighted. Furthermore, the printing parameters and the different possibilities of designing these medical applications have been explored.

Direct-Ink-Write 3D Printing of Hydrogels into Biomimetic Soft Robots.

Hydrogels are promising starting materials for biomimetic soft robots as they are intrinsically soft and hold properties analogous to nature's organic parts. However, the restrictive mold-casting and post-assembly fabrication alongside mechanical fragility impedes the development of hydrogel-based soft robots. Herein, we harness biocompatible alginate as a rheological modifier to manufacture 3D freeform architectures of both chemically and physically cross-linked hydrogels using the direct-ink-write (DIW) printing. The intrinsically hydrophilic polymer network of alginate allows the preservation of the targeted functions of the host hydrogels, accompanied by enhanced mechanical toughness. The integration of free structures and available functionalities from diversified hydrogel family renders an enriched design platform for bioinspired fluidic and stimulus-activated robotic prototypes from an artificial mobile tentacle, a bioengineered robotic heart with beating-transporting functions, and an artificial tendril with phototropic motion. The design strategy expands the capabilities of hydrogels in realizing geometrical versatility, mechanical tunability, and actuation complexity for biocompatible soft robots.

3D-Printed Hydrogel Composites for Predictive Temporal (4D) Cellular Organizations and Patterned Biogenic Mineralization.

Materials chemistries for hydrogel scaffolds that are capable of programming temporal (4D) attributes of cellular decision-making in supported 3D microcultures are described. The scaffolds are fabricated using direct-ink writing (DIW)-a 3D-printing technique using extrusion to pattern scaffolds at biologically relevant diameters (≤ 100 µm). Herein, DIW is exploited to variously incorporate a rheological nanoclay, Laponite XLG (LAP), into 2-hydroxyethyl methacrylate (HEMA)-based hydrogels-printing the LAP-HEMA (LH) composites as functional modifiers within otherwise unmodified 2D and 3D HEMA microstructures. The nanoclay-modified domains, when tested as thin films, require no activating (e.g., protein) treatments to promote robust growth compliances that direct the spatial attachment of fibroblast (3T3) and preosteoblast (E1) cells, fostering for the latter a capacity to direct long-term osteodifferentiation. Cell-to-gel interfacial morphologies and cellular motility are analyzed with spatial light interference microscopy (SLIM). Through combination of HEMA and LH gels, high-resolution DIW of a nanocomposite ink (UniH) that translates organizationally dynamic attributes seen with 2D gels into dentition-mimetic 3D scaffolds is demonstrated. These analyses confirm that the underlying materials chemistry and geometry of hydrogel nanocomposites are capable of directing cellular attachment and temporal development within 3D microcultures-a useful material system for the 4D patterning of hydrogel scaffolds.

Ultraviolet-Assisted Direct Ink Write to Additively Manufacture All-Aromatic Polyimides.

All-aromatic polyimides have degradation temperatures above 500 °C, excellent mechanical strength, and chemical resistance, and are thus ideal polymers for high-temperature applications. However, their all-aromatic structure impedes additive manufacturing (AM) because of the lack of melt processability and insolubility in organic solvents. Recently, our group demonstrated the design of UV-curable polyamic acids (PAA), the precursor of polyimides, to enable their processing using vat photopolymerization AM. This work leverages our previous synthetic strategy and combines it with the high solution viscosity of nonisolated PAA to yield suitable UV-curable inks for UV-assisted direct ink write (UV-DIW). UV-DIW enabled the design of complex three-dimensional structures comprising of thin features, such as truss structures. Dynamic mechanical analysis of printed and imidized specimens confirmed the thermomechanical properties typical of all-aromatic polyimides, showing a storage modulus above 1 GPa up to 400 °C. Processing polyimide precursors via DIW presents opportunity for multimaterial printing of multifunctional components, such as three-dimensional integrated electronics.