RESUMO
Freeze-casting has been wildly exploited to construct porous ceramics but usually requires costly and demanding freeze-drying (high vacuum, size limit, and supercooled chamber), which can be avoided by the ambient pressure drying (APD) technique. However, applying APD to freeze-cast ceramic based on an aqueous suspension is still challenging due to inert surface chemistry. Herein, a modified APD strategy is developed to improve the drying process of freeze-cast ceramics by exploiting the simultaneous ice etching, ionic cross-linking, and solvent exchange under mild conditions (-10-0 °C, ambient pressure). This versatile strategy is applicable to various ceramic species, metal ions, and freezing techniques. The incorporated metal ions not only enhance liquid-phase sintering, producing ceramics with higher density and mechanical properties than freeze-cast counterparts, but also render customizable coloration and antibacterial property. The cost-/time-efficient APD is promising for mass production and even successive production of large-size freeze-cast ceramics that exceed the size of commercial freeze-dryers.
RESUMO
Amylase is an enzyme used to hydrolyze starch in order to obtain different products that are mainly used in the food industry. The results reported in this article refer to the immobilization of α-amylase in gellan hydrogel particles ionically cross-linked with Mg2+ ions. The obtained hydrogel particles were characterized physicochemically and morphologically. Their enzymatic activity was tested using starch as a substrate in several hydrolytic cycles. The results showed that the properties of the particles are influenced by the degree of cross-linking and the amount of immobilized α-amylase enzyme. The temperature and pH at which the immobilized enzyme activity is maximum were T = 60 °C and pH = 5.6. The enzymatic activity and affinity of the enzyme to the substrate depend on the particle type, and this decreases for particles with a higher cross-linking degree owing to the slow diffusion of the enzyme molecules inside the polymer's network. By immobilization, α-amylase is protected from environmental factors, and the obtained particles can be quickly recovered from the hydrolysis medium, thus being able to be reused in repeated hydrolytic cycles (at least 11 cycles) without a substantial decrease in enzymatic activity. Moreover, α-amylase immobilized in gellan particles can be reactivated via treatment with a more acidic medium.
Assuntos
Hidrogéis , alfa-Amilases Pancreáticas , Suínos , Estabilidade Enzimática , Enzimas Imobilizadas/química , alfa-Amilases/metabolismo , Temperatura , Íons , Amido , Concentração de Íons de Hidrogênio , AnimaisRESUMO
The literature indicates the existence of a relationship between rhamnolipids and bacterial biofilm, as well as the ability of selected bacteria to produce rhamnolipids and alginate. However, the influence of biosurfactant molecules on the mechanical properties of biofilms are still not fully understood. The aim of this research is to determine the effect of rhamnolipids concentration, CaCl2 concentration, and ionic cross-linking time on the mechanical properties of alginate hydrogels using a Box-Behnken design. The mechanical properties of cross-linked alginate hydrogels were characterized using a universal testing machine. It was assumed that the addition of rhamnolipids mainly affects the compression load, and the value of this parameter is lower for hydrogels produced with biosurfactant concentration below CMC than for hydrogels obtained in pure water. In contrast, the addition of rhamnolipids in an amount exceeding CMC causes an increase in compression load. In bacterial biofilms, the presence of rhamnolipid molecules does not exceed the CMC value, which may confirm the influence of this biosurfactant on the formation of the biofilm structure. Moreover, rhamnolipids interact with the hydrophobic part of the alginate copolymer chains, and then the hydrophilic groups of adsorbed biosurfactant molecules create additional calcium ion trapping sites.
Assuntos
Alginatos/química , Bactérias/crescimento & desenvolvimento , Biofilmes/crescimento & desenvolvimento , Glicolipídeos/química , Hidrogéis/química , Líquidos Iônicos/química , Algoritmos , Modelos TeóricosRESUMO
In the present study, the fabrication of a biomimetic wound dressing that mimics the extracellular matrix, consisting of a hydrogel matrix composed of non-oxidized and periodate-oxidized marine alginate, was prepared to which gelatin was bound via Schiff base formation. Into this alginate/oxidized-alginate-gelatin hydrogel, polyP was stably but reversibly integrated by ionic cross-linking with Zn2+ ions. Thereby, a soft hybrid material is obtained, consisting of a more rigid alginate scaffold and porous structures formed by the oxidized-alginate-gelatin hydrogel with ionically cross-linked polyP. Two forms of the Zn-polyP-containing matrices were obtained based on the property of polyP to form, at neutral pH, a coacervate-the physiologically active form of the polymer. At alkaline conditions (pH 10), it will form nanoparticles, acting as a depot that is converted at pH 7 into the coacervate phase. Both polyP-containing hydrogels were biologically active and significantly enhanced cell growth/viability and attachment/spreading of human epidermal keratinocytes compared to control hydrogels without any adverse effect on reconstructed human epidermis samples in an in vitro skin irritation test system. From these data, we conclude that polyP-containing alginate/oxidized-alginate-gelatin hydrogels may provide a suitable regeneratively active matrix for wound healing for potential in vivo applications.
Assuntos
Alginatos/química , Biomimética , Gelatina/química , Hidrogéis/química , Queratinócitos/efeitos dos fármacos , Polifosfatos/química , Cicatrização , Materiais Biocompatíveis/química , Movimento Celular , Sobrevivência Celular , Epiderme/metabolismo , Matriz Extracelular/química , Humanos , Concentração de Íons de Hidrogênio , Íons , Queratinócitos/citologia , Queratinócitos/efeitos da radiação , Nanopartículas Metálicas/química , Nanopartículas/química , Porosidade , Pele/efeitos da radiação , Espectroscopia de Infravermelho com Transformada de Fourier , Engenharia Tecidual , Alicerces Teciduais/química , Zinco/químicaRESUMO
As an emerging class of dynamic cross-linked network, vitrimers have attracted much attention due to the combination of mechanical advantages of thermosets and recyclability of thermoplastics at an elevated temperature. In particular, most vitrimers with multi-shape memory properties usually involve more than one thermal transition or molecular switch, which might pose a challenge for facile sample fabrication and potentially limits their applications. In pursuit of a more universal and simple route, utilizing commercially available and inexpensive reagents to prepare shape-memory vitrimers with dual cross-linked network from vinyl monomer-derived prepolymers is reported here. Copolymerization of desired vinyl monomers gives prepolymers containing carboxyl and zinc carboxylate groups, which are later converted into vitrimers in a single step by post-curing with diglycidylether of bisphenol A. The Zn2+ ions can not only act as physical crosslinking points through ionic coordination interactions, thus providing the triple-shape-memory properties, but also play the role of catalyst to activate transesterification in the dynamic covalent network. This new self-catalyzed vitrimer has excellent transesterification efficiency, triple-shape-memory properties, and can be sufficiently healed and reprocessed at an elevated temperature. The proposed molecular design of self-catalyzed materials opens a new avenue toward commercially relevant fabrication of high-performance vitrimers with multiple shape-memory properties.
Assuntos
Ácidos Carboxílicos/química , Reagentes de Ligações Cruzadas/química , Polímeros/química , Zinco/química , Catálise , Reagentes de Ligações Cruzadas/síntese química , Estrutura Molecular , Polimerização , Polímeros/síntese química , TemperaturaRESUMO
In this study, the effect of the ionic cross-linking mode on the ability to control physical properties and in vitro release behavior of the dexamethasone (DEX) drug from chitosan (CS) and chitosan/hydroxyapatite (CS/HA) beads was investigated. CS solutions without and with HA and DEX were dripped into two coagulation solutions, prepared with a non-toxic ionic crosslinker (sodium tripolyphosphate, TPP) and distilled water, one at pH = 9.0 and other at pH = 6.0. Optical microscopy (OM) and scanning electron microscopy (SEM) results showed changes on the surface topology of the beads, with a reduction of roughness for beads prepared at pH = 6.0 and an increase for the one prepared at pH = 9.0. The diameter and sphericity of the beads prepared at pH = 6.0 proved more uniform and had a larger pore size with a good interconnectivity framework. Attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) suggested a higher crosslinking degree for beads prepared at pH = 6.0, corroborated by X-ray diffraction profiles (XRD) analysis that indicated a decrease in the crystalline structure for such beads. In in vitro drug release data, all beads presented a sustained release during the studied period (24 h). The drug release rate was affected by the pH of the coagulation solution used in the preparation of the beads. The in vitro kinetics of the release process was of the Peppas-Sahlin model, controlled by both diffusion and relaxation of polymer chains or swelling (anomalous transport mechanism). Our results suggest that DEX-loaded CS/HA beads, crosslinked in TPP coagulation solution at pH = 9.0, led to a decrease in the DEX release rate and prolonged the release period. Thus, this composition might have prospective as a functional material for bone and cartilage tissue engineering.
Assuntos
Quitosana/química , Dexametasona/administração & dosagem , Durapatita/química , Íons/química , Microesferas , Materiais Biocompatíveis/química , Reagentes de Ligações Cruzadas/química , Preparações de Ação Retardada/química , Dexametasona/química , Portadores de Fármacos/química , Concentração de Íons de Hidrogênio , Cinética , Microscopia Eletrônica de Varredura , Espectroscopia de Infravermelho com Transformada de Fourier , Difração de Raios XRESUMO
Quercetin is a kind of flavonol compound, which has been widely concerned because of its good pharmacological effects. However, its poor water solubility and poor oral absorption limit its application. To address the above problems, the optimal technological conditions for preparing quercetin-loaded chitosan sodium alginate nanoparticles (Q-CSNPs) were obtained through single-factor experiment method. Q-CSNPs were characterized by particle size analyzer, scanning electron microscope (SEM), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FTIR). Biofilm experiment evaluated the antibacterial activity of five different concentrations of Q-CSNPs against Escherichia coli and Staphylococcus aureus. DPPH and hydroxyl radical scavenging experiments determined their antioxidant activity. The effect of Q-CSNPs labeled with FITC on the oxidative stress of planarian was determined. The results showed that quercetin was successfully encapsulated and had good antibacterial and antioxidant capacity in vitro. In vivo experiments of planarians also showed that Q-CSNPs could inhibit the oxidative stress induced by lipopolysaccharide (LPS) and especially alleviate the decrease of CAT activity and the increase of MDA content in planarians induced by LPS. After being supported by future in vivo studies, this preparation will provide research possibilities for the development of quercetin nano-drugs, quercetin dietary supplement, and so on.
Assuntos
Quitosana , Nanopartículas , Planárias , Animais , Quercetina/farmacologia , Quercetina/química , Lipopolissacarídeos/farmacologia , Antioxidantes/farmacologia , Antioxidantes/química , Estresse Oxidativo , Antibacterianos/farmacologia , Antibacterianos/química , Quitosana/farmacologia , Quitosana/química , Nanopartículas/química , Biofilmes , Tamanho da PartículaRESUMO
To address the plasticization phenomenon and MOF-polymer interfacial defects, we report the synthesis of ionic cross-linked MOF MMMs from a dual brominated polymer and MOF components by using N,N'-dimethylpiperazine as the cross-linker. We synthesized brominated MIL-101(Cr) nanoparticles by using mixed linkers and prepared brominated polyimide (6FDA-DAM-Br) to form ionic cross-linked MMMs. The gas permeation properties of the polyimide, ionic cross-linked MOF-polymer MMMs, and non-cross-linked MOF-polymer MMMs with various MOF weight loadings were investigated systematically to effectively understand the effects of MOF weight loading and ionic cross-linking. The ionic cross-linked 40 wt % MOF-polymer MMM exhibited significantly enhanced gas permeability with an H2 permeability of 1640 Barrer and CO2 permeability of 1981 Barrer and slightly decreased H2/CH4, H2/N2, CO2/CH4 and CO2/N2 selectivities of 16.9, 15.4, 20.5, and 18.6, respectively. The H2 and CO2 permeabilities are approximately 2-3 fold higher than those of the pure polyimide (6FDA-DAM) membrane. Moreover, the ionic cross-linked 40 wt % MOF-polymer MMM exhibited significantly increased resistance to plasticization. This is because the brominated MOF incorporation boosted molecular transport and polymer chain rigidity, and ionic cross-linking further reduced the number of interfacial defects and polymer chain mobility.
RESUMO
Most hydrogels have poor mechanical properties, severely limiting their potential applications, and numerous approaches have been introduced to fabricate more robust and durable examples. However, these systems consist of nonbiodegradable polymers which limit their application in tissue engineering. Herein, we focus on the fabrication and investigate the influence of hydrophobic segments on ionic cross-linking properties for the construction of a tough, biodegradable hydrogel. A biodegradable, poly(γ-glutamic acid) polymer conjugated with a hydrophobic amino acid, l-phenylalanine ethyl ester (Phe), together with an ionic cross-linking group, alendronic acid (Aln) resulting in γ-PGA-Aln-Phe, was initially synthesized. Rheological assessments through time sweep oscillation testing revealed that the presence of hydrophobic domains accelerated gelation. Comparing gels with and without hydrophobic domains, the compressive strength of γ-PGA-Aln-Phe was found to be six times higher and exhibited longer stability properties in ethylenediaminetetraacetic acid solution, lasting for up to a month. Significantly, the contribution of the hydrophobic domains to the mechanical strength and stability of ionic cross-linking properties of the gel was found to be the dominant factor for the fabrication of a tough hydrogel. As a result, this study provides a new strategy for mechanical enhancement and preserves ionic cross-linked sites by the addition of hydrophobic domains. The development of tough, biodegradable hydrogels reported herein will open up new possibilities for applications in the field of biomaterials.
Assuntos
Hidrogéis , Interações Hidrofóbicas e Hidrofílicas , Hidrogéis/química , Hidrogéis/síntese química , Reagentes de Ligações Cruzadas/química , Ácido Poliglutâmico/química , Ácido Poliglutâmico/análogos & derivados , Reologia , Força Compressiva , Íons/química , Materiais Biocompatíveis/química , Fenilalanina/química , Fenilalanina/análogos & derivadosRESUMO
Inspired by the charge-governed protein channels located in the cell membrane, a series of polyether ether ketone-based polymers with side chains containing ionically cross-linkable quaternary ammonium groups and acidic groups have been designed and synthesized to prepare monovalent cation-selective membranes (MCEMs). Three acidic groups (sulfonic acid, carboxylic acid, and phenolic hydroxyl) with different acid dissociation constant (pKa) were selected to form the ionic cross-linking structure with quaternary ammonium groups in the membranes. The ionic cross-linking induced the nanophase separation and constructed ionic channels, which resulted in excellent mechanical performance and high cation fluxes. Interesting, the cation flux of membranes increased as the ionization of acidic groups increase, but the selectivity of MCEMs did not follow the same trend, which was mainly dependent on the affinity between the functional groups and the cations. Carboxyl group-containing MCEMs exhibited the best selectivity (9.01 for Li+/Mg2+), which was higher than that of the commercial monovalent cation-selective CIMS membrane. Therefore, it is possible to prepare stable MCEMs through a simple process using ionically cross-linkable polymers, and tuning acidic groups in the membranes provided an attractive approach to improving the cation flux and selectivity of MCEMs.
RESUMO
In this study, biodegradable oxidized methacrylated alginate (OMA) hydrogels with controllable mechanical properties were engineered. An ionic and photo cross-linking combination was employed to fabricate dual cross-linked hydrogels. By altering the degree of methacrylation and polymer concentration, hydrogels with an elastic modulus of 4.85 ± 0.13 to 21.02 ± 0.91 kPa, controllable swelling, and degradation kinetics, and cross-link density in the range of 1.0 × 10-5 to 6.5 × 10-5 mol/cm3 were obtained. Moreover, evaluating the effect of cross-linking sequence on the hydrogels' mechanical properties demonstrated that in comparison to the hydrogels fabricated by ionic cross-linking followed by photo-polymerization, hydrogels produced by photo-polymerization followed by ionic cross-linking retain a stiffer gel network with more compact structure. Cytocompatibility examination was performed via MTT assay against L929 fibroblasts, and all the hydrogel samples demonstrated high cell viability (>80%). The findings demonstrate the significant effect of the sequence of cross-linking as a novel tool to tune the OMA hydrogel's final properties which can serve as a useful platform for tissue engineering applications.
Assuntos
Metacrilatos , Polímeros , Metacrilatos/química , Hidrogéis/química , Alginatos/química , Tempo de Reação , Engenharia TecidualRESUMO
Alginate hydrogels are gaining traction for use in drug delivery, regenerative medicine, and as tissue engineered scaffolds due to their physiological gelation conditions, high tissue biocompatibility, and wide chemical versatility. Traditionally, alginate is decorated at the carboxyl group to carry drug payloads, peptides, or proteins. While low degrees of substitution do not cause noticeable mechanical changes, high degrees of substitution can cause significant losses to alginate properties including complete loss of calcium cross-linking. While most modifications used to decorate alginate deplete the carboxyl groups, we propose that alginate modifications that replenish the carboxyl groups could overcome the loss in gel integrity and mechanics. In this report, we demonstrate that restoring carboxyl groups during functionalization maintains calcium cross-links as well as hydrogel shear-thinning and self-healing properties. In addition, we demonstrate that alginate hydrogels modified to a high degree with azide modifications that restore the carboxyl groups have improved tissue retention at intramuscular injection sites and capture blood-circulating cyclooctynes better than alginate hydrogels modified with azide modifications that deplete the carboxyl groups. Taken together, alginate modifications that restore carboxyl groups could significantly improve alginate hydrogel mechanics for clinical applications. STATEMENT OF SIGNIFICANCE: Chemical modification of hydrogels provides a powerful tool to regulate cellular adhesion, immune response, and biocompatibility with local tissues. Alginate, due to its biocompatibility and easy chemical modification, is being explored for tissue engineering and drug delivery. Unfortunately, modifying alginate to a high degree of substitution consumes carboxyl group, which are necessary for ionic gelation, leading to poor hydrogel crosslinking. We introduce alginate modifications that restore the alginate's carboxyl groups. We demonstrate that modifications that reintroduce carboxyl groups restore gelation and improve gel mechanics and tissue retention. In addition to contributing to a basic science understanding of hydrogel properties, we anticipate our approach will be useful to create tissue engineered scaffolds and drug delivery platforms.
Assuntos
Alginatos , Hidrogéis , Adesão Celular , Injeções , Engenharia TecidualRESUMO
The development of smart elastomeric materials with inherent self-repairing abilities after mechanical damage has important technological and scientific implications, particularly in regard to the durability and life cycle of rubber products. The interest in self-healing materials for automotive applications is rapidly growing along with the increasing importance of vehicle scratch quality and quantity. The creation of a reversible network by noncovalent ionic cross-linking in elastomer/rubber blends is an effective approach to generate the self-healing phenomenon, with reprocessing and recycling properties. In this work, thermoplastic vulcanizates (TPVs) were prepared using ethylene-propylene-diene (EPDM) polymers and high-acid-containing thermoplastic ionomers. Along with the general EPDM, maleic anhydride grafted EPDM (EPDM-g-MAH) was also used for the preparation of the TPVs. The strategy was based on a simple ionic crosslinking reaction between the carboxyl groups present in the ionomer and zinc oxide (ZnO), where the formation of reversible Zn2+ salt bondings exhibits the self-healing behavior. The heterogeneous blending of EPDM and ionomers was also used to investigate the thermal and mechanical properties of the TPVs. The experimental findings were further supported by the surface morphology of the fracture surfaces viewed using microscopy. The self-healing behavior of the TPVs has been identified by scratch resistance testing, where the EPDM-g-MAH TPVs showed excellent healing efficiency of the scratch surface. Therefore, this work provides an efficient approach to fabricate new ionically cross-linked thermoplastic vulcanizates with excellent mechanical and self-repairing properties for the skins of automotive interior door trims and instrument panel applications.
RESUMO
Benefiting from the associative exchange reaction, vitrimers could be deformed to various shapes while maintaining the integrity of the network, thus being regarded as promising candidates for shape memory polymers. However, it is still a challenge to design the highly desired smart electronic devices with triple and multishape memory performances through a facile method. Here, a novel dual-cross-linked poly(acrylonitrile-co-butyl acrylate-co-hydroxyethyl methacrylate-co-zinc methacrylate) (Zn-PABHM) copolymer was developed via a facile and one-pot free radical polymerization strategy. Ionic cross-linking, the transcarbamoylation reaction, and glass transition were used to fix the permanent shape and two temporary shapes of the obtained ionomer vitrimer, respectively. The thermomechanical and stress relaxation performances of Zn-PABHM vitrimer can be customized by tuning the proportion of the chemical cross-linking and physical cross-linking knots. Furthermore, the Zn-PABHM was employed to construct a shape memory triboelectric nanogenerator, which demonstrates distinctive performance and tunable electrical outputs (37.4-96.0 V) due to variable contact areas enabled by triple shape memory effects. Consequently, the triple-shape memory ionomer vitrimer obtained via a facile and one-pot synthetic strategy has great potential in smart multifunctional electronic devices.
RESUMO
BACKGROUD: Ginsenoside compound K (GK) is a major metabolite of protopanaxadiol-type ginsenosides and has remarkable anticancer activities in vitro and in vivo. This work used an ionic cross-linking method to entrap GK within O-carboxymethyl chitosan (OCMC) nanoparticles (Nps) to form GK-loaded OCMC Nps (GK-OCMC Nps), which enhance the aqueous solubility and stability of GK. METHODS: The GK-OCMC Nps were characterized using several physicochemical techniques, including x-ray diffraction, transmission electron microscopy, zeta potential analysis, and particle size analysis via dynamic light scattering. GK was released from GK-OCMC Nps and was conducted using the dialysis bag diffusion method. The effects of GK and GK-OCMC Nps on PC3 cell viability were measured by using the 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2-H-tetrazolium bromide assay. Fluorescent technology based on Cy5.5-labeled probes was used to explore the cellular uptake of GK-OCMC Nps. RESULTS: The GK-OCMC NPs had a suitable particle size and zeta potential; they were spherical with good dispersion. In vitro drug release from GK-OCMC NPs was pH dependent. Moreover, the in vitro cytotoxicity study and cellular uptake assays indicated that the GK-OCMC Nps significantly enhanced the cytotoxicity and cellular uptake of GK toward the PC3 cells. GK-OCMC Nps also significantly promoted the activities of both caspase-3 and caspase-9. CONCLUSION: GK-OCMC Nps are potential nanocarriers for delivering hydrophobic drugs, thereby enhancing water solubility and permeability and improving the antiproliferative effects of GK.
RESUMO
MXenes are an emerging class of highly conductive two-dimensional (2D) materials with electrochemical storage features. Oriented macroscopic Ti3C2Tx fibers can be fabricated from a colloidal 2D nematic phase dispersion. The layered conductive Ti3C2Tx fibers are ideal candidates for constructing high-speed ionic transport channels to enhance the electrochemical capacitive charge storage performance. In this work, we assemble Ti3C2Tx fibers with a high degree of flake orientation by a wet spinning process with controlled spinning speeds and morphology of the spinneret. In addition to the effects of cross-linking of magnesium ions between Ti3C2Tx flakes, the electronic conductivity and mechanical strength of the as-prepared fibers have been improved to 7200 S cm-1 and 118 MPa, respectively. The oriented Ti3C2Tx fibers present a volumetric capacitive charge storage capability of up to 1360 F cm-3 even in a Mg-ion based neutral electrolyte, with contributions from both nanofluidic ion transport and Mg-ion intercalation pseudocapacitance. The oriented 2D Ti3C2Tx driven nanofluidic channels with great electronic conductivity and mechanical strength endows the MXene fibers with attributes for serving as conductive ionic cables and active materials for fiber-type capacitive electrochemical energy storage, biosensors, and potentially biocompatible fibrillar tissues.
RESUMO
The selection of sacrificial support materials is important in the fabrication of complex freeform structures. In this study, a dual droplet-based, freeform 3D printing method for pseudoplastic alginate biomaterial inks was developed using Bingham plastic cellulose nanocrystals (CNCs) as support nanomaterials. CNCs-CaCl2 mixture compositions and alginate concentrations were varied to enhance printability with rheological properties of shape fidelity and structural stability. The mixtures supported the shape of alginate and allowed CaCl2 diffusion-based cross-linking during 3D printing. The hydrogels showed rheological and physicochemical properties similar to those of pure alginate hydrogel, as CNCs were removed during post-printing processing. BSA-loaded multi-layered spheres, freeform 3D-printed for oral protein drug delivery, protected BSA in the gastric environment and provided controlled and sustained release of BSA into the intestinal environment as layer width and alginate concentration increased. This method can facilitate freeform 3D printing of diverse pseudoplastic biomaterial inks for biomedical applications.
Assuntos
Celulose , Alginatos , Hidrogéis , Impressão Tridimensional , Engenharia TecidualRESUMO
Curcumin has essential therapeutic benefits, but it is insoluble in water and thus has low bioavailability. This study aimed to immobilize curcumin into new polysaccharide-based microparticles (gellan, i-carrageenan, and chitosan) to increase its stability and bioavailability. Curcumin-loaded complex microparticles were obtained from three polysaccharides, of different ionic character, by ionic cross-linking and polyelectrolyte complexation. The immobilization efficiency was between 85.75% and 97.25%. The microparticles were characterized morphologically by SEM, and it was observed that the microparticles containing the i-carrageenan had a more pronounced porosity of the matrix. The swelling degree values at pH = 7.4 were superior to those obtained at pH = 6.8 or pH = 2 and depend on both the cross-linking degree and particles morphology. The polysaccharides microparticles, curcumin, and constituent polysaccharides were characterized by FT-IR spectroscopy. The curcumin release kinetics was studied in three different pH media, and the release efficiency ranged between 65.1% and 97.9% at pH = 7.4, between 60.2% and 82.2% at pH = 6.8 and between 56.1% and 64.0% at pH = 2. These microparticles can be intended for oral administration, having as therapeutic target the colon, for the controlled release of curcumin, since they can overcome the gastric barrier without the degradation of the active principle, which is protected by the polymer matrix.
Assuntos
Curcumina/química , Portadores de Fármacos , Sistemas de Liberação de Medicamentos , Polissacarídeos/química , Administração Oral , Disponibilidade Biológica , Carragenina/química , Quitosana/química , Curcumina/uso terapêutico , Géis/química , Humanos , Concentração de Íons de Hidrogênio , Microesferas , Tamanho da Partícula , Polieletrólitos/química , Polímeros/química , Espectroscopia de Infravermelho com Transformada de FourierRESUMO
Copper(II) sulfate-loaded chitosan microparticles were herein prepared using ionic cross-linking with sodium tripolyphosphate (STPP) followed by spray drying. The microencapsulation process was optimal using an inlet temperature of 180 °C, a liquid flow-rate of 290 mL/h, an aspiration rate of 90%, and an atomizing gas flow-rate of 667 nL/h. Chitosan particles containing copper(II) sulfate of approximately 4 µm with a shrunken-type morphology were efficiently attained and, thereafter, fixated on a paper substrate either via cross-linking with STPP or using a chitosan hydrogel. The latter method led to the most promising system since it was performed at milder conditions and the original paper quality was preserved. The developed cellulose substrates were reduced and then exposed to different humidity conditions and characterized using colorimetric measurements in order to ascertain their potential as irreversible indicators for moisture detection. The results showed that the papers coated with the copper(II) sulfate-containing chitosan microparticles were successfully able to detect ambient moisture shown by the color changes of the coatings from dark brown to blue, which can be easily seen with the naked eye. Furthermore, the chitosan microparticles yielded no cytotoxicity in an in vitro cell culture experiment. Therefore, the cellulose substrates herein developed hold great promise in paper packaging as on-package colorimetric indicators for monitoring moisture in real time.
RESUMO
This study investigates the impact of dual ionic and covalent cross-links (ion-XrL and cov-XrL) on the properties of chitosan-based (CTS) hydrogels as eco-friendly drug delivery systems (DDS) for the model drug diclofenac sodium (DCNa). Citric acid and a diiodo-trehalose derivative (ITrh) were the chosen ionic and covalent cross-linker, respectively. The novel hydrogels completely disintegrated within 96 h by means of a hydrolysis process mediated by the enzyme trehalase. As far as the authors are aware, this is the first time that a trehalose derivative has been used as a covalent cross-linker in the formation of biodegradable hydrogels. The impact of CTS concentration and degree of cov-XrL on rheological parameters were examined by means of an experimental model design and marked differences were found between the materials. Hydrogels with maximum elastic properties were achieved at high CTS concentrations and high degrees of cov-XrL. DCNa-loaded formulations displayed well-controlled drug-release profiles strongly dependent on formulation composition (from 17% to 40% in 72 h). Surprisingly, higher degrees of covalent cross-linking led to a boost in drug release. The formulations presented herein provides a simple and straightforward pathway to design fully biodegradable, tailor-made controlled drug delivery systems with improved rheological properties.