LED-Based Desktop Analyzer for Fat Content Determination in Milk.

In dairy, there is a growing request for laboratory analysis of the main nutrients in milk. High throughput of analysis, low cost, and portability are becoming critical factors to provide the necessary level of control in milk collection, processing, and sale. A portable desktop analyzer, including three light-emitting diodes (LEDs) in the visible light region, has been constructed and tested for the determination of fat content in homogenized and raw cow's milk. The method is based on the concentration dependencies of light scattering by milk fat globules at three different wavelengths. Univariate and multivariate models were built and compared. The red channel has shown the best performance in prediction. However, the joint use of all three LED signals led to an improvement in the calibration model. The obtained preliminary results have shown that the developed LED-based technique can be sufficiently accurate for the analysis of milk fat content. The ways of its further development and improvement have been discussed.

A Simple Procedure to Assess Limit of Detection for Multisensor Systems.

Currently, there are no established procedures for limit of detection (LOD) evaluation in multisensor system studies, which complicates their correct comparison with other analytical techniques and hinders further development of the method. In this study we propose a simple and visually comprehensible approach for LOD estimation in multisensor analysis. The suggested approach is based on the assessment of evolution of mean relative error values in calibration series with growing analyte concentration. The LOD value is estimated as the concentration starting from which MRE values become stable from sample to sample. This intuitive procedure was successfully tested with a variety of real data from potentiometric multisensor systems.

Multichannel Acoustic Spectroscopy of the Human Body for Inviolable Biometric Authentication.

Specific features of the human body, such as fingerprint, iris, and face, are extensively used in biometric authentication. Conversely, the internal structure and material features of the body have not been explored extensively in biometrics. Bioacoustics technology is suitable for extracting information about the internal structure and biological and material characteristics of the human body. Herein, we report a biometric authentication method that enables multichannel bioacoustic signal acquisition with a systematic approach to study the effects of selectively distilled frequency features, increasing the number of sensing channels with respect to multiple fingers. The accuracy of identity recognition according to the number of sensing channels and the number of selectively chosen frequency features was evaluated using exhaustive combination searches and forward-feature selection. The technique was applied to test the accuracy of machine learning classification using 5,232 datasets from 54 subjects. By optimizing the scanning frequency and sensing channels, our method achieved an accuracy of 99.62%, which is comparable to existing biometric methods. Overall, the proposed biometric method not only provides an unbreakable, inviolable biometric but also can be applied anywhere in the body and can substantially broaden the use of biometrics by enabling continuous identity recognition on various body parts for biometric identity authentication.

A different approach for the analysis of grapes: Using the skin as sensing element.

In this work, an alternative method to monitor the phenolic maturity of grapes was developed. In this approach, the skins of grapes were used to cover the surface of carbon paste electrodes and the voltammetric signals obtained with the skin-modified sensors were used to obtain information about the phenolic content of the skins. These sensors could easily detect differences in the phenolic composition of different Spanish varieties of grapes (Mencía, Prieto Picudo and Juan García). Moreover, sensors were able to monitor changes in the phenolic content throughout the ripening process from véraison until harvest. Using PLS-1 (Partial Least Squares), correlations were established between the voltammetric signals registered with the skin-modified sensors and the phenolic content measured by classical methods (Glories or Total Polyphenol Index). PLS-1 models provided additional information about Brix degree, density or sugar content, which usually used to establish the harvesting date. The quality of the correlations was influenced by the maturation process and the structural and mechanical skin properties. Thus the skin sensors fabricated with Juan García and Prieto Picudo grapes (that showed faster polyphenolic maturation and a higher amount of extractable polyphenols than Mencía), showed good correlations and therefore could be used to monitor the ripening.

A combination of dynamic measurement protocol and advanced data treatment to resolve the mixtures of chemically similar analytes with potentiometric multisensor system.

Data processing techniques and measuring protocol are very important parts of the multisensor systems methodology. Complex analytical tasks like resolving the mixtures of two components with very similar chemical properties require special attention. We report on the application of non-linear (artificial neural networks, ANNs) and linear (projections on latent structures, PLS) regression techniques to the data obtained from the flow cell with potentiometric multisensor detection of neighouring lanthanides in the Periodic System of the elements (samarium, europium and gadolinium). Quantification of individual components in mixtures is possible with reasonable precision if dynamic components of the response are incorporated thanks to the use of an automated sequential injection analysis system. The average absolute error in prediction of lanthanides with PLS was around 1 × 10(-4)mol/L, while the use of ANNs allows the lowering of prediction errors down to 2 × 10(-5)mol/L in certain cases. The suggested protocol seems to be useful for other analytical applications where simultaneous determination of chemically similar analytes in mixtures is required.

Mimicking Daphnia magna bioassay performance by an electronic tongue for urban water quality control.

Toxicity is one of the key parameters of water quality in environmental monitoring. However, being evaluated as a response of living beings (as their mobility, fertility, death rate, etc.) to water quality, toxicity can only be assessed with the help of these living beings. This imposes certain restrictions on toxicity bioassay as an analytical method: biotest organisms must be properly bred, fed and kept under strictly regulated conditions and duration of tests can be quite long (up to several days), thus making the whole procedure the prerogative of the limited number of highly specialized laboratories. This report describes an original application of potentiometric multisensor system (electronic tongue) when the set of electrochemical sensors was calibrated against Daphnia magna death rate in order to perform toxicity assessment of urban waters without immediate involvement of living creatures. PRM (partial robust M) and PLS (projections on latent structures) regression models based on the data from this multisensor system allowed for prediction of toxicity of unknown water samples in terms of biotests but in the fast and simple instrumental way. Typical errors of water toxicity predictions were below 20% in terms of Daphnia death rate which can be considered as a good result taking into account the complexity of the task.

Monitoring changes in behaviour from multi-sensor systems.

Behavioural patterns are important indicators of health status in a number of conditions and changes in behaviour can often indicate a change in health status. Currently, limited behaviour monitoring is carried out using paper-based assessment techniques. As technology becomes more prevalent and low-cost, there is an increasing movement towards automated behaviour-monitoring systems. These systems typically make use of a multi-sensor environment to gather data. Large data volumes are produced in this way, which poses a significant problem in terms of extracting useful indicators. Presented is a novel method for detecting behavioural patterns and calculating a metric for quantifying behavioural change in multi-sensor environments. The data analysis method is shown and an experimental validation of the method is presented which shows that it is possible to detect the difference between weekdays and weekend days. Two participants are analysed, with different sensor configurations and test environments and in both cases, the results show that the behavioural change metric for weekdays and weekend days is significantly different at 95% confidence level, using the methods presented.